Professional Documents
Culture Documents
A1 2015
A1 2015
Which part of the Directorate General of Civil Aviation govern the issuance of
an
a.
b.
c.
d.
Certificate of Airworthiness
Part 21
Part 23
Part 25
Part 39
preventive
d. The repair of portions of skin sheets by making additional seams major
repairs
10.Type certificate is the design approval for a new (model) aircraft; engine or
propeller;
a. To certify that the products design complies with authority standard
b. Which will be issued for individual aircraft, engine, or propeller
c. Issued for transport category
d. A and B answer are correct
11.What is the Newtons second law in more specific sense, the relationship
between mass, velocity, acceleration and distance?
a. Force equal calculation from momentum and velocity
b. Force equal action and reaction from self-force
c. Force equal calculation from mass and acceleration
d. Force equal calculation from rate of change moment
12.An aircraft weighs 6,400 pounds. How much force is needed to give it an
acceleration of 6 ft/sec2 (if set of gravity 32 ft/sec2)
a. 1,000 lb
b. 1,200 lb
c. 3,800 lb
d. 2,600 lb
13.What is the differential X2 + 2X + 5 ;
a. 2X + 5
b. 2X + 2
c. 1/3X3 + X2 + 5X
d. X3 + X2 + 5X
2X + 6
19.A piece of sheet metal is bent to a certain radius. The curvature of the bend
is referred to as the?
a. Bend allowance
b. Neutral line
c. Bend radius
d. Metal size
20.When a butt welded joint is visually inspected for penetration?
a. The penetration should be 25 to 50 percent of the thickness of the base
metal
b. The penetration should be 100 percent of the thickness of the base metal
c. The penetration should covered of the base metal
d. Look for evidence of excessive heat in the form of a very high bead
21.The diameter of pilot drill for pre-drilling of rivet hole should be;
a. 0.001 higher than diameter of rivet approximately 0.003 greater
than diameter of rivet shanks
b. 0.001 lower than diameter of rivet
c. Max 0.006 higher than diameter of rivet
d. The same as diameter of rivet
22.The aluminum code number 1100 identifies?
a. Aluminum alloy containing 11 percent copper
b. Aluminum alloy containing zinc
c. 99 percent commercially pure aluminum
d. 100 percent of pure aluminum
23.The second digit of aluminum designation identifies
a. The specific alloy modification
b. The percent of alloy group
c. The alloy type first digit
d. The different alloys in a group
b. The handle
c. The shank and length
d. The tip and the face
34.Which of the following bolts can be called as the special purpose bolt?
a. Hex head bolt with drilled shank
b. Airframe bolt and engine bolts
c. Clevis bolt and jo bolt
d. Close tolerance bolt and drilled head bolt
47.Boundary layer control device for hi lift application feature various devices to
maintain hi velocity in boundary layer and delay separation of the airflow.
The kind of method for controlling boundary layer air are :
a. Fix slot
b. Automatic slot
c. Control by flap augmentation
d. All are true
48.How is the installation of speed brakes on the aircraft?
a. On tail cone rear structure
b. On the left and right sides of rear fuselage
c. On the wing upper surface
d. As mentioned on a, b, and c
49.When spoiler is used to assist the ailerons, the movement is as follows :
a. The right spoiler surfaces moves up to make the aircraft bank left
b. The left spoiler surfaces moves up to make the aircraft bank right
c. When right spoilers move up the aircraft bank right, and when left
spoilers move up the aircraft bank left
d. A and b are correct
d. Grow up aspect ratio low induced drag, cause wing tip vortices is
affected by increasing in lift
61.The wing loading of an aircraft is:
a. The total gross weight of the aircraft divided by wing area W/S (W:
gross weight; S: wing surface)
b. The payload of the aircraft divided by wing area
c. The all-up weight of the aircraft in o wing area
d. The tare weight of the aircraft over wing area
62.What is the relationship between induced and parasite drag when the gross
weight is increase:
a. Induced drag increases more than parasite drag
b. Both parasite and induced drag are equally increased
c. Parasite drag increases more than induced drag
d. Both parasite and induced drag are equally decrease,
(afm airframe vol 1 pg G-20)
(afm airframe vol 1 pg G-25)
63.What changes to aircraft control must be made to maintain altitude while the
airspeed is being decreased:
a. Increase angle of attack to produce more lift than weight
b. Decrease the angle of attack to compensate for the decrease in drag
c. Increase the angle of attack to compensate for the decreasing dynamic
pressure
d. Maintain a constant angle of attack until the desired airspeed is reached,
then increase the angle of attack. most probable
64.The configuration of inverse dihedral wing is
a. Wings have positive angle towards the longitudinal axis
b. Wings have negative angle towards lateral axis rigging dihedral angle
c. Wings have positive angle towards lateral axis
d. Wings have negative angle towards longitudinal axis
65.Balance tab is
a. An adjustable tab mounted on the leading edge of a control surface to
produce a force automatically that aids the pilot in moving the surface
b. An adjustable tab mounted on the trailing edge of a control surface to
produce a force that aids the pilots in moving the surface
c. A non-adjustable tab mounted on the trailing edge of a control surface to
omit a force that aids the pilot in moving the surface
d. A control surface to produce a force automatically that aids the pilot in
moving the surface.
66.
67.The internal resistance of fluid which tends to prevent it from flowing is called
a. Viscosity
b. .
c. Velocity
d. Capacity
68.Centering cam
a. A cam in the main gear shock strut that cause the piston to center when
the strut fully extend
b. A cam in the left hand main-gear shock strut that cause the piston to
center when the strut fully extends
c. A cam in the nose gear shock strut that cause the piston to center when
the strut fully compress
d. A cam in the nose gear shock strut that cause the piston to center when
the strut fully extends.
69.Some aircraft uses pneumatic power to operate some systems. Which of the
following system normally uses high-pressure pneumatic system? high
pressure pneumatic system generally for emergency use
a. Ice & rain protection system use low and medium pressure
b. Landing gear system (retraction) extension as emergency
c. Pressure System
d. A and B are true
70.What device in hydraulic system with a constant delivery pump allows
circulation of the fluid when no demands are on the system?
a. Pressure relief valve as safety
b. Shuttle valve selector, safety
c. Pressure regulator
d. Debooster valve
71.Hydraulic fluid reservoirs are sometimes designed with a standpipe in one of
the outlet port in order to assure emergency supply of fluid. The outlet port
with the standpipe in it furnishes fluid to the:
a. Normal system power pump
b. Emergency pump when the fluid supply to the normal system has been
depleted.
c. Emergency pump at any time is required.
d. Normal pump when the fluid supply to the normal system has been
depleted
72.What produces the temperature drop drastically in air cycle cooling system?
a. Compressor
b. Turbine
c. Heat exchanger
d. Water separator
73.On
a.
b.
c.
d.
74.If condition below was occurs, generally on pneumatic system the SOV /
PRSOV will automatic close, except..
a. Over temperature
b. Over pressure
c. Leak
d. Over Speed
75.On
a.
b.
c.
d.
85. how many thing that are done when the fire warning switch handle in the
cockpit is pulled are :
a. Engine fuel shut off valve is closed, thrust reverser control power goes
off, and spar fuel valve closes.
b. power to engine driven pump low-pressure-warning system goes off,
bleed air valve closes
c. engine fuel shut off valve is closed, thrust reverser control power goes
off, power to engine driven pump low-pressure-warning system goes off,
spar fuel valve closes, , bleed air valve closes and hydraulic shut off
valve is closes
d. Hydraulic shut off valve is closes, engine fuel shut off valve is closed,
thrust reverser control power goes off, and spar fuel valve closes.
86.the cargo compartments are pressurized class D (smother type)
compartments for fire protection , planned on :
a. any fire starting in the compartments will allow the oxygen and
distinguishers
b. any fire starting in the compartments will left the oxygen and
distinguishers itself
c. any fire starting in the compartments will consume the oxygen and
extinguishers itself
d. any fire starting in the compartments will consume the oxygen and
distinguishers itself
87.three instrument are normally connected to the aircraft to the static air
source, there are :
a. airspeed indicator, outside air temperature indicator, altimeter
b. altimeter, oil pressure indicator, oil temperature indicator
c. altimeter, airspeed indicator, vertical speed indicator
d. absolute altimeter, vertical speed indicator, airspeed indicator
On simple aircraft, this may consist of a pitot-static system head or pitot
tube with impact and static air pressure ports and leak-free tubing
connecting these air pressure pickup points to the instruments that require
the air for their indications. The altimeter, airspeed indicator, and vertical
speed indicator are the three most common pitot-static instruments.
88.during climb, the air pressure inside the diaphragm of vertical speed
indicator :
a. smaller than air pressure in the instrument case
b. higher than air pressure in the instrument case
c. the same as air pressure in the instrument case
d. smaller than static pressure outside of aircraft
During a climb, the metering unit will establish the required factors
and differential pressure, but as the static pressure under this condition is
a decreasing one, and because the metering unit restricts the
flow out of the case, the case pressure leads the capsule pressure.
89.the component in automatic flight control system that actually applies force
to move the control surface is the :
a. servo
b. hydraulic probably most correct
c. mechanically
d. pressure
90.a rate gyro operates on the gyroscopic characteristic of
a. precession
b. rigidity
c. acceleration
d. deviation
91.an aircraft magnetic compass is swung to update the compass correction
card when
a. an annual inspection
b. the compass service
c. deviation error
d. variation
92.the
a.
b.
c.
commutator is used to
supply the AC output of the generator to the external circuit
produce DC in the armature conductors
convert the generated AC inside the armature to DC for the external
circuit
d. to split the AC output from DC generator
The Commutator: The voltage induced in the armature is AC.
The commutator changes the AC voltage into DC voltage.
93.the
a.
b.
c.
d.