Professional Documents
Culture Documents
Section 6 Pockets
Section 6 Pockets
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of MechoShade Systems, Inc. Paintloc is a trademark of its respective company.
Specifications subject to change without notice.
http://SolarControlLLC.com
Solar Control, LLC | 888-550-4836
1. #4123 Recessed Pocket with Tile Support. Extruded 6. Custom Sized Bent Pockets. Custom sized bent pockets
aluminum shade pocket, 5-15/16" W x 5-1/4" H x 15ft. L up to 10 ft. long are available by special order. Call your
(135mm x 133mm x 457cm), in 6063T5 baked PPG enamel MechoShade technical support representative for
finish in standard white or standard custom colors by size limitations.
special order. Comes with exposed flush mounted tile
support for acoustical tile or dry wall soffits and ceilings. 7. Return Air Option Pockets. Return Air Option is a series
An optional exposed flush mounted extruded aluminum of ventilation holes, punched into the side wall of the pocket.
removable closure panel is available to provide access This allows for heated return air to vent into the plenum.
to the shades. (See item 8.) Return Air Pockets minimize the potential for thermal
stress when shades are extended over the glazing.
2. #4133 Surfaced Mounted Pocket. No Tile Support. Especially for room darkening glazing systems. Venting
Extruded aluminum shade pocket, 4-3/4" W x 5" H x 15ft. L the concentrated heat, between the shade and window,
(121mm x127mm x 457cm), in 6063T5 baked PPG enamel minimizes the heat entering the room and improves the
finish in standard white or standard custom colors by special efficiency of the HVAC. For Return Air Pockets add “AR”
order. An optional exposed flush mounted extruded to the pocket number, i.e. 4123AR, 4133RA, etc. Standard
aluminum removable closure panel is available to return air openings: 12 square inches per linear foot
2
provide access to the shades. (See item 8.) (774.2mm per liner meter). If different return air is
required it must be specified.
3. #5113 Recessed Pocket with Tile Support. Steel shade
pocket, 8-3/4" W x 9-1/2" H x 10ft. L (223mm x 241mm x 8. Closures. Extruded aluminum pocket closure assembly
305cm), unpainted with white trim. Comes with exposed in 6063T5 baked PPG enamel finish in standard white or
flush mounted tile support for acoustical tile or dry wall standard custom colors by special order. Closure panel
soffits and ceilings. An optional exposed flush mounted available in 2", 3" and 5" x 15ft. (50mm, 76mm and
extruded aluminum removable closure panel is available 127mm x 457cm. or custom width.
to provide access to the shades. (See item 8.)
9. Single Closure Mount and Closure Mount with Tile
4. #6113 Recessed Pocket with Tile Support. Steel shade Support. Extruded aluminum Single Closure Mount or
pocket, 9-1/4" W x 15" H x 10ft. L (235mm x 381mm x Closure Mount with built in Tile Support in 6063T5 baked
305cm), unpainted with white trim. Comes with exposed PPG enamel finish in standard white or standard custom
flush mounted tile support for acoustical tile or dry wall colors by special order. Single Closure Mount 1-1/2" W x
soffits and ceilings. An optional exposed flush mounted 2-5/6" H x 15ft. L (38mm x 59mm x 457cm). Closure
extruded aluminum removable closure panel is available Mount with Tile Support 3/8" W x 2-5/16" H x 15ft.
to provide access to the shades. (See item 8.) (910mm x 59mm x 457cm).
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of MechoShade Systems, Inc. Specifications subject to change without notice.
http://SolarControlLLC.com
Solar Control, LLC | 888-550-4836
Optional
Pocket End Cap
Part No. UPCA 4650 AL WH
5" (127mm)
Mecho/5
Pocket
Bracket
* MechoShade recommends a 2" Closure (P/N: UCLX 2015 AL WH) with a chaindrawn system and a 3" Closure (P/N: UCLX 3015 AL WH) with a motorized system.
CORNER
5-1/2"
(22mm)
3" (76mm) Closure
Exterior
Exterior
Shade Fabric
(25 mm)
Shade Fabric
1"
Interior
Interior
(140mm)
5-1/2"
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of MechoShade Systems, Inc. Specifications subject to change without notice.
http://SolarControlLLC.com
Solar Control, LLC | 888-550-4836
(241mm)
Bracket
9-1/2"
Direction
Direction of Air Flow
of Air Flow
Direction
of travel
5" (127mm) Closure
Sold Separately
7/16"
(10mm) Min. 1/2" (13mm)
DoubleShade™ application 3-1/2" (89mm) 5" (127mm)
with 5113 Pocket 1-1/4"
(32mm)
8-1/2" (216mm)
#7113
Blackout
RECESSED (Reverse Roll)
POCKET SunScreen
(Regular Roll)
(P/N: APTS 7113 ST PL)
8-1/2" (216mm)
Electro/1 Electro/1
(P/N: UCLX 3015 AL WH) Extended Extended
Bracket Bracket
5" (127mm) Closure
sold separately.
1/4"
ShadeCloths
1-1/4"
14" (356mm)
(31mm)
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of, and DoubleShade is a trademark of, MechoShade Systems, Inc.
Specifications subject to change without notice.
http://SolarControlLLC.com
Solar Control, LLC | 888-550-4836
15" (381mm)
SunScreen
Continuous
Blocking
(By Others)
Shown with
Electro/1
Extended
Bracket
ShadeCloths
Direction
of travel Direction
Larger shades are possible of travel
with custom made brackets.
3" or 5" Closure
Sold Separately
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of MechoShade Systems, Inc. Specifications subject to change without notice.
http://SolarControlLLC.com
Solar Control, LLC | 888-550-4836
(59mm)
2-5/16"
2"
(50.8mm)
(29mm)
1-1/8"
1/16"
3" CLOSURE (3mm)
(29mm)
(10mm)
5" CLOSURE
(59mm)
2-5/16"
(29mm)
1-1/8"
1-1/8"
1-1/4"
5"
(32mm)
(127mm)
1-1/2"
(38mm)
© Copyright 2004, MechoShade Systems, Inc., Long Island City, NY. MechoShade and ElectroShade are registered trademarks of MechoShade Systems, Inc. Specifications subject to change without notice.
http://SolarControlLLC.com