Professional Documents
Culture Documents
Ray of Reflection Washing Lens User's Guide
Ray of Reflection Washing Lens User's Guide
Ray of Reflection
Washing Lens
Users Guide
Lens
A
Laser
TUbe
F1-3
far
infrared
F1-1
ray
wave
band.It
is
an
F1-4
and
standard
adjusting
methods
of
45
CO2
Car
directio
n
45
45
B
Transport
ing beam
D
Car nozzle
F141
Obviousely,The
F142
fly-light-route
of
Suny
Laser
Focusing
Lens
D,Car
head,Transporting
Beam,Car Nozzle.
2.Light route adjusting:
1. Laser tube Light Route adjusting:
Firstly, install and adjust the laser tube:put
the
laser
tube
plane
,ensure
-3-
the
anode
water
inleting,
cathode(light
outleting.also
ensure
outlet)
water
inlet
water
lower,water
outlet higher.
Secondly,adjust
the
Laser
tube
bracket
Reflecting
Leans A
A
Water
outlet
Bracket
screw
F2-1
E
Water
inlet
supply,observe
there
is
or
not
red
pre
speed to 1%.
Last,stick
double
glue
to
the
face
of
come
photo),if
F2-2
F2-3
no
Laser
tube
-5-
and
down,clockwise
up,anticlockwise down
Adjust this screw, optical route move
right and left, clockwise right, anticlockwise left.
Adjust this screw, optical route move
right
and
left,clockwise
right,anti-
clockwise left
F2-4
The methods:
1.Adjust
Reflector
optical route:
F2-5
near
as
possible
to
F2-5
reflector A
, Put adhesive tapes (other paper) on reflecting mirror A(attention
adhesive far from lens surface, the same to the right photo), press the
reflecting button to dot the tapes(or other paper), then move the beam a
little ,dot the tapes again, secondly,move the beam farther and the farthest
then dot separately on the tapes ,check if the two dots overlap or not,if not
,adjust the screw of reflector A as the F2-4 photo until the dots overlap.
move
farther
the
small
and
the
car
to
farthest
or
not,if
not,
F2-7
F2-8
F2-9
Pass
F2-10
If the focus route deviates, adjust the screw
of
refector
until
the
route
sites
in
the
-9-
F2-11
Attention here:there is one special matter that
the shelves of the small car deformed caused by
Laser machine transporting,then the focus optical
route vertical angle deviates in a large range.
The urgent resolution is:fill one paper gasket
between the car head and shelve(or another suitable
thickness of materials)
one
thickness),
pcs
doting
of
plexiglass
some
time
by
(with
10mm
laser,observ
(not pass)
(pass)
parallelogram.
3. focus distance adjustment:
focus distance is defined the focus of lentiform
lens,but in order for our easy use, usually the
focus distance means to adjust the distance from
the small car nozzle to the working area.
100%
light
cutting,(the
intensity
material
1%
speed
can
to
be
selftesting
rubber
or
- 11 -
- 12 -
4. Install the reflector on the mount. Do not touch the lens nor blow it
with your mouth.
3. Cleaning Products:
Cleanser: the common cleanser used is prepared as aether:ethanol
=1:3, user can prepare the special cleanser-camera lens cleanser on his
own.
Cleaning Paper: special lens paper for camera only, no other products
are allowed.
The above-mentioned materials are available in camera apparatus
shop.
- 13 -