Professional Documents
Culture Documents
Adj6 Anexos Relativos de La Norma de Pintura para Las Unidades y Sus Equipos A
Adj6 Anexos Relativos de La Norma de Pintura para Las Unidades y Sus Equipos A
Adj6 Anexos Relativos de La Norma de Pintura para Las Unidades y Sus Equipos A
May.2012
Beijing, China
Catalog
1.Technologicalprocedureofrustpreventionandinnerpackingforthrust
runnerplateofhydrogenerator(0605015)
2.Technologicalprocedureofrustpreventionandinnerpackingforshaftof
hydraulicturbineandhydraulicgenerator(0605016)
3.SigmaZinc102(7402)
4.SigmaCover280(7417)
5.SigmaGuard720(7433)
6.SigmaCover456(7466)
7.SigmaDur550(7537)
8.SigmaShield420(7951)
9.Tectyl506
10.Tectyl890
Rev.A
THE PEOPLE'S REPUBLIC OF CHINA
0605-015
HARBIN
Form No.00
0605-015
Technological
procedure
of
rust
prevention and inner packing for thrust
runner plate of hydro generator
Rev. A
1
PAGE
MODIFICATION CONTENT ABSTRACT
PAGE&ITEM
PREPARED BY &
REVIEWED BY
1
OF
1
DATE
Form No.G
0605-015
Technological procedure of rust prevention and
inner packing for thrust runner plate of hydro
generator
Rev. A
1
PAGE
OF
1 Scope
This procedure applies to rust prevention and inner packing of thrust runner plate of hydro
generator.
This procedure excludes the contents of transportation, packing and protection to be done
before the runner plate is transported out of factory.
2 Material
Table 1
description
type
Spec
stretch film
SF/LF-25
width 457 mm
SF/H104-110PA
width 340 mm
anti-rust compound
Tectyl 890
572#
gasoline
200#
cotton cloth
3 Environmental requirement
3.1
and over 45,relative humidity not over 80,temperature of machine part itself at least 3
over dew point.
3.2
Cleanliness of environment
The work place for oil sealing, rust prevention and packing shall be clean, no flying dust;
Prepared by
Checked by
Date
Reviewed by
Counter sign
Counter sign
Date
Date
Standardization
Authorized by
Date
Approved by
Date
Date
Date
Form No.01
0605-015
Technological procedure of rust prevention and inner packing for thrust runner
plate of hydro generator
Rev. A
2
PAGE
3
OF
Description
Wipe clean all the surfaces of runner plate All the surfaces shall not have oily dirt
with 200# gasoline
and other contaminants.
Wrap with one layer of stretchable film Application of stretchable film shall be
( SF/LF -25)
tight, lapped area shall be at least 150mm
Form No.02
0605-015
Technological procedure of rust prevention and inner packing for thrust runner
plate of hydro generator
Rev. A
3
PAGE
3
OF
5 Safety precaution
5.1
The operators shall wear working clothes, protective gauze mask, globes and goggles,
5.3
If the used material touches skin due to carelessness, immediately wash with worm water
and soap. if eye contaminated with used material, rinse with fresh water at least 10 minutes and
immediately see a doctor. It is strictly prohibited to use solvent to rub wash skin.
5.4
Anti-rust agent shall be kept far away from spark and/or flame, smoking is strictly
Form No.02
Rev.B
THE PEOPLE'S REPUBLIC OF CHINA
0605-016
HARBIN
Form No.00
0605-016
Technological procedure of rust prevention and
inner packing for shaft of hydraulic turbine
and hydraulic generator
Rev. B
1
PAGE
MODIFICATION CONTENT ABSTRACT
PAGE&ITEM
PREPARED BY &
REVIEWED BY
1
OF
1
DATE
Form No.G
0605-016
Rev. B
4
PAGE
OF
1 Scope
This procedure applies to rust prevention and inner packing of
description
type
spec
SF/FO-175 PL
width 2250 mm
LB cloth PE
width 1m~1.2m
Antirust paper
SF/H104-110PA
width 1020 mm
anti-rust compound
Tectyl 890
Pearl-like floss
EPE
thickness 5 mm
3M adhesive tape
6969#
width 50 mm
gasoline
200#
cotton cloth
stretch film
Prepared by
Checked by
Date
Date
Reviewed by
Counter sign
SF/LF-25
Counter sign
Date
Date
Standardization
width 457 mm
Authorized by
Date
Approved by
Date
Date
Date
Form No.01
0605-016
Technological procedure of rust prevention and inner packing for shaft of hydraulic
turbine and hydraulic generator
Rev. B
2
PAGE
4
OF
3 General requirement
3.1
ambient temperature not below 5 and over 45,relative humidity not over 80,temperature
of machine part itself at least 3 over dew point.
3.2
Cleanliness of environment
The work place for oil sealing, rust prevention and packing shall be clean, no flying dust;
cleanliness of air shall reach to general requirement.
3.3
3.4
During handling the shaft, avoid damaging the oil sealed packing.
Support the two side flanges, oil sealing and antirust packing for the shaft body ( see
Table 2).
4.2
Support the shaft body, perform oil sealing and anti-rust packing for the flanges at both
The operators shall wear working clothes, protective gauze mask, globes and goggles,
5.3
If the used malarial touches skin due to carelessness, immediately wash with worm water
and soap. if eye contaminated with used material, rinse with fresh water at least 10 minutes and
immediately see a doctor. It is strictly prohibited to use solvent to rub wash skin.
5.4
Anti-rust agent shall be kept far away from spark and/or flame, smoking is strictly
Anti-rust agent shall be stored as it falls in the category of inflammable and explosive
goods.
Form No.02
0605-016
Technological procedure of rust prevention and inner packing for shaft of hydraulic
turbine and hydraulic generator
Rev. B
3
PAGE
4
OF
Table 2
1
2
Description
Quality requirement and inspection
#
Wipe clean all the surfaces of shaft with 200 All the surfaces shall not have oily dirt
gasoline
and other contaminants.
All metal surfaces shall be uniformly
Apply two layers of Tectyl 890 anti-rust
coated, uncoated sports existed are not
compound
allowed
layer
of
Form No.02
0605-016
Technological procedure of rust prevention and inner packing for shaft of hydraulic
turbine and hydraulic generator
Rev. B
4
4
PAGE
OF
Table 3
Description
Rub wash all metal surfaces with 200# All surfaces should not have oily dirt and other
gasoline
contaminants.
Apply two layers of Tectyl 890 anti-rust All metal surfaces should be coated uniformly,
compound
any uncoated sports should not existed
Wrap with one layer of stretchable film Application of stretchable film shall be tight,
(SF/LF-25)
lapped area shall be at least 150 mm
packed
6969 #
flange,
on the
Form No.02
DATA
SIGMAZINC 102
(SIGMACOVER ZINC PRIMER)
4 pages
DESCRIPTION
September 2005
Revision of April 2005
PRINCIPAL CHARACTERISTICS
grey - flat
Mass density
Volume solids
VOC (supplied)
2.1 g/cm
55 2%
max. 193 g/kg (Directive 1999/13/EC, SED)
max. 410 g/l (approx. 3.4 lb/gal)
25 - 50 m depending on blasting profile; dfts of more then 50 m are not
recommended
22 m/l for 25 m *
15 min. at 20C *
min. 6 hours *
max. several months *
7 days
at least 12 months
base 46C, hardener 32C
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
Induction time
none
Pot life
Page 1/4
DATA
SIGMAZINC 102
(SIGMACOVER ZINC PRIMER)
September 2005
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets
this is a solvent based paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
ADDITIONAL DATA
Page 2/4
15.7
11
7.3
35
50
75
DATA
SIGMAZINC 102
(SIGMACOVER ZINC PRIMER)
September 2005
touch dry
dry to handle
full cure
40 min.
30 min.
15 min.
10 min.
4 hours
2 hours
2 hours
1 hour
20 days
10 days
7 days
5 days
Page 3/4
Whilst it is always the aim of Sigma Coatings to supply the same product on
a worldwide basis, slight modification of the product is sometimes
necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
DATA
SIGMAZINC 102
(SIGMACOVER ZINC PRIMER)
September 2005
REFERENCES
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance
only. All recommendations or suggestions relating to the use of the products made by Sigma Coatings, whether in technical
documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and
it is the end-user's responsibility to determine the suitability of the product for its intended use.
Sigma Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use
and application of the product. Sigma Coatings does therefore not accept any liability arising from loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet
is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
DS
179384
Page 4/4
7402
0000001800
DATA
SIGMACOVER 280
(SIGMA UNIVERSAL PRIMER - SIGMACOVER PRIMER)
5 pages
DESCRIPTION
September 2005
Revision of July 2005
PRINCIPAL CHARACTERISTICS general purpose epoxy primer in protective coating systems for steel and
non ferrous metals
good adhesion to steel and galvanised steel
good adhesion to non ferrous metals
good flow and wetting properties
good water and corrosion resistance
cures at temperatures down to +5C
suitable for touching up of weld seams and damages of epoxy coatings
during construction
long recoating intervals are possible when overcoating with epoxy and
polyurethane coatings (under cover)
can be overcoated with most alkyd-, chlorinated rubber-, vinyl-, epoxyand two component polyurethane coatings
suitable on wet blast cleaned substrates (damp or dry)
compatible with well designed cathodic protection systems
COLOURS AND GLOSS
Mass density
Volume solids
VOC (supplied)
1.3 g/cm
57 2%
max. 327 g/kg (Directive 1999/13/EC, SED)
max. 432 g/l (approx. 3.6 lb/gal)
50 - 100 m depending on system
at least 24 months
base 26C, hardener 26.5C
* see additional data
Page 1/5
DATA
SIGMACOVER 280
(SIGMA UNIVERSAL PRIMER - SIGMACOVER PRIMER)
September 2005
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
marine
system sheets
none
8 hours at 20C *
* see additional data
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Page 2/5
DATA
SIGMACOVER 280
(SIGMA UNIVERSAL PRIMER - SIGMACOVER PRIMER)
September 2005
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets
this is a solvent based paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
ADDITIONAL DATA
7.6
5.7
75
100
Page 3/5
50 m
40C
4 hours
3 months
2 months
DATA
SIGMACOVER 280
(SIGMA UNIVERSAL PRIMER - SIGMACOVER PRIMER)
September 2005
touch dry
dry to handle
full cure
8 hours
4 hours
2 hours
1 hour
45 min.
13 hours
6 hours
2.5 hours
1.5 hour
1 hour
21 days
14 days
7 days
5 days
3 days
10 hours
8 hours
5 hours
4 hours
Worldwide availability
Whilst it is always the aim of Sigma Coatings to supply the same product on
a worldwide basis, slight modification of the product is sometimes
necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
REFERENCES
Page 4/5
DATA
SIGMACOVER 280
(SIGMA UNIVERSAL PRIMER - SIGMACOVER PRIMER)
September 2005
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance
only. All recommendations or suggestions relating to the use of the products made by Sigma Coatings, whether in technical
documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and
it is the end-user's responsibility to determine the suitability of the product for its intended use.
Sigma Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use
and application of the product. Sigma Coatings does therefore not accept any liability arising from loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet
is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
DS
179083 yellow/green
179085 redbrown
Page 5/5
7417
4009002200
6137002200
DATA
SIGMAGUARD 720
(SIGMAGUARD EHB)
4 pages
DESCRIPTION
September 2005
Revision of January 2003
PRINCIPAL CHARACTERISTICS tank coating with good chemical resistance against a wide range of
chemicals
short curing periods
good low temperature curing
easy to clean
Recognized corrosion control coating (Lloyd's register), see sheet 1886
COLOURS AND GLOSS
Mass density
Volume solids
VOC (supplied)
1.4 g/cm
78 2%
max. 163 g/kg (Directive 1999/13/EC, SED)
max. 233 g/l (approx. 1.9 lb/gal)
125 m *
at least 12 months
base 28C, hardener 25C
* see additional data
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
tankcoatings
Page 1/4
DATA
SIGMAGUARD 720
(SIGMAGUARD EHB)
September 2005
Induction time
Pot life
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
BRUSH
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets
this is a solvent based paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
ADDITIONAL DATA
Page 2/4
6.2
125
100 m
DATA
SIGMAGUARD 720
(SIGMAGUARD EHB)
September 2005
Overcoating table
substrate
5C
10C
20C
temperature
minimum
32 hours 24 hours 8 hours
interval
maximum
28 days 28 days 28 days
interval
30C
40C
4 hours
3 hours
14 days
7 days
Page 3/4
3 hours
1.5 hour
1 hour
30 min.
Whilst it is always the aim of Sigma Coatings to supply the same product on
a worldwide basis, slight modification of the product is sometimes
necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
DATA
SIGMAGUARD 720
(SIGMAGUARD EHB)
September 2005
REFERENCES
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance
only. All recommendations or suggestions relating to the use of the products made by Sigma Coatings, whether in technical
documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and
it is the end-user's responsibility to determine the suitability of the product for its intended use.
Sigma Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use
and application of the product. Sigma Coatings does therefore not accept any liability arising from loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet
is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
DS
179122 grey
180730 green
Page 4/4
7433
5000002200
4000002200
DATA
SIGMACOVER 456
(SIGMA CM COATING - SIGMACOVER CM COATING)
5 pages
DESCRIPTION
September 2005
Revision of September 2004
PRINCIPAL CHARACTERISTICS general purpose epoxy build coat or finish in protective coating systems
for steel and concrete structures exposed to atmospheric land or marine
conditions
easy application, both by airless spray and brush
cures even at temperatures down to -10C
a high relative humidity max. 95%, during application and curing does
not influence the quality of the coating
good adhesion on most aged, sound alkyd-, chlorinated rubber- and
epoxy coatings
can be recoated with various two component and conventional coatings
even after long weathering periods
resistant to water and splash of mild chemicals
excellent durability
tough, with long term flexibility
COLOURS AND GLOSS
white and various other colours (see also Marine shade card) - semigloss
Mass density
Volume solids
VOC (supplied)
1.4 g/cm
65 2% (white); 62 - 65 2% (colours)
max. 250 g/kg (Directive 1999/13/EC, SED)
max. 347 g/l (approx. 2.9 lb/gal)
75 - 150 m depending on system
at least 24 months
base 26C, hardener 26.5C
* see additional data
Page 1/5
DATA
SIGMACOVER 456
(SIGMA CM COATING - SIGMACOVER CM COATING)
September 2005
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
marine
none
6 hours at 20C
* see additional data
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets
this is a solvent based paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
Page 2/5
DATA
SIGMACOVER 456
(SIGMA CM COATING - SIGMACOVER CM COATING)
September 2005
ADDITIONAL DATA
6.5
4.3
100
150
60 m
10C
20C
30C
40C
4
hours
3
hours
2
hours
2
hours
minimum
interval
maximum
interval
maximum
interval
10C
20C
30C
40C
72
24
hours hours
no limitation
16
hours
8
hours
5
hours
3
hours
17
days
10
days
7
days
4
days
2
days
14
days
Page 3/5
DATA
SIGMACOVER 456
(SIGMA CM COATING - SIGMACOVER CM COATING)
September 2005
Curing table
substrate temperature
-10C
-5C
0C
5C
10C
15C
20C
30C
40C
dry to handle
24-48 hours
24-30 hours
18-24 hours
18 hours
12 hours
8 hours
6 hours
4 hours
3 hours
full cure
20 days
14 days
10 days
8 days
6 days
5 days
4 days
3 days
2 days
12 hours
6 hours
4 hours
2 hours
Worldwide availability
Whilst it is always the aim of Sigma Coatings to supply the same product on
a worldwide basis, slight modification of the product is sometimes
necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
REFERENCES
Page 4/5
DATA
SIGMACOVER 456
(SIGMA CM COATING - SIGMACOVER CM COATING)
September 2005
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance
only. All recommendations or suggestions relating to the use of the products made by Sigma Coatings, whether in technical
documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and
it is the end-user's responsibility to determine the suitability of the product for its intended use.
Sigma Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use
and application of the product. Sigma Coatings does therefore not accept any liability arising from loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet
is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
DS
179073 white
Page 5/5
7466
7000002200
DATA
SIGMADUR 550
4 pages
DESCRIPTION
September 2005
Revision of April 2005
PRINCIPAL CHARACTERISTICS
unlimited recoatable
excellent resistance to atmospheric exposure conditions
excellent colour and gloss retention
non-chalking, non-yellowing
cures at temperatures down to -5C
resistant to splash of mineral and vegetable oils, paraffins, aliphatic
petroleum products and mild chemicals
can be recoated even after long atmospheric exposure
good application properties
white and various other colours (see also Marine shade card) - gloss
Mass density
Volume solids
VOC (supplied)
1.3 g/cm
56 2%
max. 334 g/kg (Directive 1999/13/EC, SED)
max. 430 g/l (approx. 3.6 lb/gal)
50 - 60 m depending on system
at least 24 months
base 33C, hardener 42C
* see additional data
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
Page 1/4
DATA
SIGMADUR 550
September 2005
Induction time
Pot life
none
5 hours at 20C *
* see additional data
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets
this is a solvent based paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
contains a toxic polyisocyanate curing agent
avoid at all times inhalation of aerosol spraymist
Page 2/4
DATA
SIGMADUR 550
September 2005
ADDITIONAL DATA
9.3
60
20C
30C
40C
6
hours
5
hours
3
hours
dry to handle
24 hours
16 hours
8 hours
6 hours
5 hours
3 hours
full cure
15 days
11 days
6 days
4 days
3 days
2 days
Page 3/4
7 hours
5 hours
3 hours
2 hours
Whilst it is always the aim of Sigma Coatings to supply the same product on
a worldwide basis, slight modification of the product is sometimes
necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
DATA
SIGMADUR 550
September 2005
REFERENCES
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance
only. All recommendations or suggestions relating to the use of the products made by Sigma Coatings, whether in technical
documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and
it is the end-user's responsibility to determine the suitability of the product for its intended use.
Sigma Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use
and application of the product. Sigma Coatings does therefore not accept any liability arising from loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet
is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
DS
238761 white
238763 white
Page 4/4
7537
7000001400
7000002200
SIGMASHIELD 420
(SIGMA MULTIGUARD)
4 pages
DESCRIPTION
January 2008
Revision of January 2007
two component reinforced high solids polyamine adduct cured epoxy coating
PRINCIPAL CHARACTERISTICS
coating for cargo tanks of bulk- or oil carriers and storage tanks
buildcoat for underwater- and boottop systems
excellent abrasion and impact resistance
excellent water resistance
easy to clean
good low temperature curing
Mass density
Volume solids
VOC (supplied)
1.6 g/cm
81 2%
max. 153 g/kg (Directive 1999/13/EC, SED)
max. 239 g/l (approx. 2.0 lb/gal)
150 - 200 m depending on system
5.4 m/l for 150 m, 4.1 m/l for 200 m *
3 hours
min. 10 hours *
max. 14 days *
5 days *
at least 12 months
* see additional data
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
previous coat; (e.g. SigmaCover 280 or SigmaShield 220) dry and free from
any contamination
substrate temperature should be at least 5C and at least 3C above dew
point during application and curing
SYSTEM SPECIFICATION
marine
the temperature of the mixed base and hardener should preferably be above
15C, otherwise extra solvent may be required to obtain application viscosity
too much solvent results in reduced sag resistance and slower cure
thinner should be added after mixing the components
Induction time
Pot life
none
1.5 hour at 20C *
* see additional data
page 1/4
SIGMASHIELD 420
(SIGMA MULTIGUARD)
January 2008
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and relevant
material safety data sheets
this is a solvent borne paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed skin
or eyes
ADDITIONAL DATA
8.1
5.4
4.6
4.1
dft in m
100
150
175
200
75 m
5C
10C
20C
30C
40C
minimum
interval
14 hours
7 hours
3.5 hours
2 hours
1.5 hour
with polyurethanes
minimum
interval
22 hours
14 hours
10 hours
6 hours
4 hours
maximum
interval
28 days
28 days
14 days
7 days
4 days
page 2/4
SIGMASHIELD 420
(SIGMA MULTIGUARD)
January 2008
dry to handle
full cure
for immersion in
seawater
full cure
5C
10C
20C
30C
40C
15 hours
8 hours
3.5 hours
2 hours
1.5 hour
10 days
7 days
5 days
4 days
3 days
17 days
14 days
7 days
5 days
3 days
for cargo hold application: for full cure for hard angular cargoes, please
contact your nearest SigmaKalon Marine & Protective Coatings sales office
adequate ventilation to remove solvent must be maintained during
application and curing (please refer to sheet 1433 and 1434)
should SigmaShield 420 or the total coating system (2 x 125 m) be applied
in excess of the specified dry film thickness, then the time necessary to
reach full cure will be increased
Pot life (at application viscosity)
10C
20C
30C
3 hours
1.5 hour
45 min.
Worldwide availability
REFERENCES
page 3/4
SIGMASHIELD 420
(SIGMA MULTIGUARD)
January 2008
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for
guidance only. All recommendations or suggestions relating to the use of the Sigma Coatings products made by
SigmaKalon Marine & Protective Coatings, whether in technical documentation, or in response to a specific enquiry,
or otherwise, are based on data which to the best of our knowledge are reliable. The products and information are
designed for users having the requisite knowledge and industrial skills and it is the end-user's responsibility to
determine the suitability of the product for its intended use.
SigmaKalon Marine & Protective Coatings has no control over either the quality or condition of the substrate, or
the many factors affecting the use and application of the product. SigmaKalon Marine & Protective Coatings does
therefore not accept any liability arising from loss, injury or damage resulting from such use or the contents of this
data sheet (unless there are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continous product
development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this
sheet is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
190960
192367
PDS
grey
redbrown
7951
5177052200
6179052200
page 4/4
TECTYL 506
Description
TECTYL 506 is a solvent cutback, wax base, corrosion
preventive compound. The dry film is firm, amber, waxy
and translucent. TECTYL 506 is excellent for long term
Laboratory Data
Typical Properties
English
100?
0.88
1.3 mils
630 sq. ft./
U.S gallon
53-57
1hour
300?
Metric
38?
0.88
32.5 microns
15.4 sq. meters/
liter
1hour
150?
-10?
3.24lbs./
U.S gallon
-23?
400 grams/
liter
2000
360
Benefits
Easy Application
TECTYL 506 is formulated for easy application by
spray, dip or brush.
Surface Preparation
The maximum performance of TECTYL 506 can
only be achieved when the metal surfaces, to be
protected, are clean and dry. Remove dirt, rust,
scaling paint and other contaminants before applying
506.
Application
Ensure Uniform consistency prior to use.
Continuous stirring or thinning is generally not
required. If product thickens due to cold storage or
loss of solvent during use, add only aliphatic mineral
spirits and only if necessary to restore consistency.
Do not apply heat; fire or explosion may result. Apply
at 50-95? (10-35? ) by spray, dip or brush.
Removal
TECTYL 506 can be removed with mineral spirits
or any similar petroleum solvent, vapor degreasing.
TECTYL 506 can be removed from fabrics by normal
dry cleaning procedures. Avoid using chlorinated or
highly aromatic solvents when removing from
painted surfaces as these solvent may adversely
affect paint.
Caution: Combustible
TECTYL 506 cures by solvent evaporation. Keep
away from heat, sparks and open flames. Use with
adequate ventilation. If applied to the interior of an
enclosed vessel adequate ventilation is required for
cure and to ensure against formation of an explosive
atmosphere. For further information, consult Korea
Houghton Corporation. Refer to Korea Houghton
Corporation Material Safety Data Sheet for health
and safety instructions.
Examples of Application
Bombardier. Chrysler. Ford. HUNDAI Heavy Industry.
DOOSAN Heavy Industry.
Coverage
The theoretical coverage is 630 sq. ft./gallon(15.4
sq. meters/liter) at the recommended dry film
thickness of 1.3 mils (32.5 microns). Material losses
during application will vary and must be considered
when estimating job requirements.
CAUTION:
The data, statements
and recommendations set forth in this
product information sheet are based
on testing, research and other
development work which has been
carefully conducted by us , and we
believe such data, statements and
recommendations will serve as
reliable guidelines. However, this
product is subject to numerable uses
under varying conditions over which
we have no control, and accordingly,
we do NOT warrant that this product
is suitable for any particular use.
Users are advised to test the product
in advance to make certain it is
suitable for their particular production
conditions and particular use or uses.
WARRANTY: Korea Houghton corporation warrants all products manufactured by it to be free from
defects in material and workmanship. KOREA HOUGHTON CORPORATION MAKE NO OTHER
WARRANTIES, WHETHER, EXPRESSED OR IMPLIED, WITH RESPECT TO SUCH
RPODUCTS, AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE AND IMPLIED WARRANTIES ARISING FROM A COURSE OF
DEALING OR USAGE OF TRADE, ARE DISCLAIMED BY KOREA HOUGHTON CORPORATION.
All claims hereunder must be made in writing within 30 days after receipt of the products at the
buyer
s plant and prior to further processing the products or combining them with other materials or
products. Korea Houghton corporation liability, whether under this warranty or in contract, tort,
negligence or otherwise, is limited to the return of the net purchase price paid for any products
proven defective or, at Korea Houghton corporation option, to the repair or replacement of said
products upon their return, transportation prepaid, to Korea Houghton corporation. THE REMEDY
HEREBY PROVIDED SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF THE BUYER, AND
UNDER NO CIRCUMSTANCES SHALL KOREA HOUGHTON CORPORATION BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, No Korea Houghton corporation representative
or other person is authorized to change this warranty in any way or to assume for Korea Houghton
corporation any other liability in connection with the sale or use of its products.
REFER TO MATERIAL SAFETY DATA SHEET FOR HEALTH AND SAFETY INFORMATION