Professional Documents
Culture Documents
UMTS UE Behavior in Idle Mode Parameter Description
UMTS UE Behavior in Idle Mode Parameter Description
UMTS UE Behavior in Idle Mode Parameter Description
Security Level
Description
T3212
ATT
DRXCYCLELEN
COEF
CN domain specific DRX cycle length coefficient broadcast on SIB1 and used by
UEs in Idle Mode.
Qqualmin
Qrxlevmin
MaxAllowedUlTx
Power
The maximum allowed uplink transmits power of a UE in the cell, which is related
to the network planning. For detailed information, refer to 3GPP TS 25.304.
IdleSintrasearch
Threshold for intra-frequency cell reselection in idle mode. When the quality
(CPICH Ec/No measured by the UE) of the serving cell is lower than this
threshold plus the [Qqualmin] of the cell, the intra-frequency cell reselection
procedure will be started. This parameter is not configured when its value is 127.
The intra-frequency cell reselection has a priority higher than the inter-frequency
cell reselection and inter-RAT cell reselection, the intra-frequency cell
reselection start threshold should be higher than the inter-frequency cell
reselection start threshold and inter-RAT cell reselection start threshold. If the
cell reselection threshold is set to a comparatively high value, the UE may
frequently start cell reselections, and the battery of the UE may be largely
consumed. If the cell reselection threshold is set to a comparatively low value, it
2013-02-06
HUAWEI Confidential
Page1, Total8
Document Title
Parameter ID
Security Level
Description
is difficult for cell reselections to be started, and the UE may not timely reside in
the cells with good quality, affecting the quality of communication between the
UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304.
IdleSintersearch
Threshold for inter-frequency cell reselection in idle mode. When the quality
(CPICH Ec/No measured by UE) of the serving cell is lower than this threshold
plus the [Qqualmin] of the cell, the inter-frequency cell reselection procedure will
be started. This parameter is not configured when its value is 127. The
intra-frequency cell reselection has a priority higher than the inter-frequency cell
reselection and inter-RAT cell reselection, the intra-frequency cell reselection
start threshold should be higher than the inter-frequency cell reselection start
threshold and inter-RAT cell reselection start threshold. If the cell reselection
threshold is set to a comparatively high value, the UE may frequently start cell
reselections, and the battery of the UE may be largely consumed. If the cell
reselection threshold is set to a comparatively low value, it is difficult for cell
reselections to be started, and the UE may not timely reside in the cells with
good quality, affecting the quality of communication between the UTRAN and the
UE. For detailed information, refer to 3GPP TS 25.304.
SsearchRat
Threshold for inter-RAT cell reselection. When the quality (CPICH Ec/No
measured by UE) of the serving cell is lower than this threshold plus the
[Qqualmin] of the cell, the inter-RAT cell reselection procedure will be started.
This parameter is not configured when its value is 127. This parameter is not
configured when its value is 127. The intra-frequency cell reselection has a
priority higher than the inter-frequency cell reselection and inter-RAT cell
reselection, the intra-frequency cell reselection start threshold should be higher
than the inter-frequency cell reselection start threshold and inter-RAT cell
reselection start threshold. If the cell reselection threshold is set to a
comparatively high value, the UE may frequently start cell reselections, and the
battery of the UE may be largely consumed. If the cell reselection threshold is set
to a comparatively low value, it is difficult for cell reselections to be started, and
the UE may not timely reside in the cells with good quality, affecting the quality of
communication between the UTRAN and the UE. For detailed information, refer
to 3GPP TS 25.304.
SsearchHCS
Intra-system HCS cell reselection start threshold. When Srxlev of the serving cell
is less than this parameter, the UE starts the intra-frequency and inter-frequency
measurements so that better cells can be selected. For details, refer to 3GPP TS
25.304.
UseOfHcs
SHCSRat
Inter-system HCS cell reselection start threshold. When Srxlev of the serving cell
is less than this parameter, the UE starts the inter-system measurement so that
better cells can be selected. For details, refer to 3GPP TS 25.304.
SlimitSearchRat
The UE does not start the inter-RAT measurement if it detects that the quality of
2013-02-06
HUAWEI Confidential
Page2, Total8
Document Title
Parameter ID
Security Level
Description
the serving cell is higher than this threshold. For detailed information of this
parameter, refer to 3GPP TS 25.304.
IdleQoffset1sn
IdleQoffset2sn
QUALMEAS
IdleQhyst1s
The hysteresis value of the serving FDD cells in idle mode in case the quality
measurement for cell selection and reselection is set to CPICH RSCP. It is
related to the slow fading feature of the area where the cell is located. The
greater the slow fading variance is, the greater this parameter.
2013-02-06
HUAWEI Confidential
Page3, Total8
Document Title
Parameter ID
Security Level
Description
According to the R regulation, the current serving cell involves in cell selection
after the measurement value is added with the hysteresis value. The
measurement hysteresis aims to prevent the ping-pong effect of the cell
reselection, which is caused by the slow fading when the UE is on the edge of
the cell. The ping-pong effect may trigger frequent location updates (idle mode),
URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus
increase the load of network signaling and the consumption of UE batteries. Set
a proper measurement hysteresis to reduce as much as possible effect of the
slow fading as well as ensuring timely cell updates of the UE. According to the
CPICH RSCP emulation report of inter-frequency hard handovers, the
measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default
when the slow fading variance is 8 dB and the relative distance is 20 m. In the
cells where the slow fading variance is low and the average moving speed of
UEs is high, for example the suburbs and countryside, reduce the measurement
hysteresis to guarantee timely location updates of UEs. The higher the
measurement hysteresis is, the less likely it is for various types of cell
reselections to occur, and the better the slow fading resistance capability is, but
the slower the system reacts to the environment changes. For detailed
information of this parameter, refer to 3GPP TS 25.304.
IdleQhyst2s
2013-02-06
The hysteresis value of the serving FDD cells in idle mode in case the quality
measurement for cell selection and reselection is set to CPICH Ec/No. It is
related to the slow fading feature of the area where the cell is located. The
greater the slow fading variance is, the greater this parameter. It is optional. If it
is not configured, [Hysteresis 1] will be adopted as the value. This parameter is
not configured when its value is 255.
According to the R regulation, the current serving cell involves in cell selection
after the measurement value is added with the hysteresis value. The
measurement hysteresis aims to prevent the ping-pong effect of the cell
reselection, which is caused by the slow fading when the UE is on the edge of
the cell. The ping-pong effect may trigger frequent location updates (idle mode),
URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus
increase the load of network signaling and the consumption of UE batteries. Set
a proper measurement hysteresis to reduce as much as possible effect of the
slow fading as well as ensuring timely cell updates of the UE. According to the
CPICH RSCP emulation report of inter-frequency hard handovers, the
measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default
when the slow fading variance is 8 dB and the relative distance is 20 m. In the
cells where the slow fading variance is low and the average moving speed of
UEs is high, for example the suburbs and countryside, reduce the measurement
hysteresis to guarantee timely location updates of UEs. The higher the
measurement hysteresis is, the less likely it is for various types of cell
HUAWEI Confidential
Page4, Total8
Document Title
Parameter ID
Security Level
Description
reselections to occur, and the better the slow fading resistance capability is, but
the slower the system reacts to the environment changes. For detailed
information of this parameter, refer to 3GPP TS 25.304.
Treselections
If the signal quality (CPICH Ec/No measured by the UE) of a neighboring cell is
better than that of the serving cell during the specified time of this parameter, the
UE reselects the neighboring cell. It is used to avoid ping-pong reselection
between different cells. Note that the value 0 corresponds to the default value
defined in the protocol.
Set the parameter as follows:
1. Ensure that the UE can reselect a cell when crossing the non-soft-switch area
of the cell and that the UE timely performs location updates, cell updates, or
URA updates when necessary.
2. Ensure that the UE does not reselect a cell when it is in the soft-switch area of
the cell. In this way, the unnecessary location updates, cell updates, and URA
updates are avoided.
3. Consider the difference between cells that cover different areas, for example
the cells covering highways and cells covering densely populated areas. TIf the
parameter is set to a comparatively low value, the ping-pong reselections may
be caused. The parameter can be increased in populated area and reduced in
high-speed movement. If the parameter is set to a comparatively high value, the
cell reselection delay may become excessively high, and thus cell reselections
may be affected.
For detailed information, refer to 3GPP TS 25.304.
HCSPrio
HCS priority of the cell belongs to. The parameter depends on HCS rules. For
details, refer to 3GPP TS 25.304.
Qhcs
Quality threshold of HCS cell reselection. It can be used to calculate the quality
level of the specified cell in HCS reselection H rules.
TpenaltyHcsRese
lect
TempOffset1
TempOffset2
MCC
MNC
2013-02-06
HUAWEI Confidential
Page5, Total8
Document Title
Security Level
Default
Value
GUI Value
Range
Actual Value
Range
Unit
MML Command
NE
T3212
10
0~255
0~1530 step:6
min
ADD
CNDOMAIN(Optional)
RNC
ATT
ALLOWED
NOT_ALLOW
ED,
ALLOWED
NOT_ALLOW
ED,
ALLOWED
None
ADD
CNDOMAIN(Optional)
RNC
DRXCYCLE
LENCOEF
6~9
6~9
None
ADD
CNDOMAIN(Optional)
RNC
Qqualmin
-18(ADD
CELLSEL
RESEL)
-(ADD
NRNCCEL
L)
-24~0
-24~0
dB
ADD
CELLSELRESEL(Optio
nal)
ADD
NRNCCELL(Mandatory
)
RNC
Qrxlevmin
-58(ADD
CELLSEL
RESEL)
-(ADD
NRNCCEL
L)
-58~-13
-115~-25,
step:2
dBm
ADD
CELLSELRESEL(Optio
nal)
ADD
NRNCCELL(Mandatory
)
RNC
MaxAllowed
UlTxPower
24(ADD
CELLSEL
RESEL)
-(ADD
NRNCCEL
L)
-50~33
-50~33
dBm
ADD
CELLSELRESEL(Optio
nal)
ADD
NRNCCELL(Mandatory
)
RNC
IdleSintrase
arch
127
-16~10, 127
{-32~20},
{127}, step:2
dB
ADD
CELLSELRESEL(Optio
nal)
RNC
IdleSinterse
arch
127
-16~10, 127
{-32~20},
{127}, step:2
dB
ADD
CELLSELRESEL(Optio
nal)
RNC
SsearchRat
127
-16~10, 127
{-32~20},
{127}, step:2
dB
ADD
CELLSELRESEL(Optio
nal)
RNC
SsearchHC
-53~45
-105~91,
dB
ADD
RNC
2013-02-06
HUAWEI Confidential
Page6, Total8
Document Title
Parameter
ID
Default
Value
Security Level
GUI Value
Range
Actual Value
Range
Unit
step:2
MML Command
NE
CELLHCS(Optional)
UseOfHcs
NOT_USE
D
USED,
NOT_USED
USED,
NOT_USED
None
ADD
CELLHCS(Optional)
ADD
GSMCELL(Optional)
ADD
NRNCCELL(Optional)
RNC
SHCSRat
-53~45
-105~91,
step:2
dB
ADD
CELLHCS(Optional)
RNC
SlimitSearc
hRat
-16~10
-32~20, step:2
dB
ADD
CELLHCS(Optional)
RNC
IdleQoffset1
sn
-50~50
-50~50
dB
ADD
INTERFREQNCELL(O
ptional)
ADD
INTRAFREQNCELL(O
ptional)
RNC
IdleQoffset2
sn
-50~50
-50~50
dB
ADD
INTERFREQNCELL(O
ptional)
ADD
INTRAFREQNCELL(O
ptional)
RNC
QUALMEA
S
CPICH_E
CNO
CPICH_ECN
O(CPICH
Ec/N0),
CPICH_RSCP
(CPICH
RSCP)
CPICH_ECN
O,
CPICH_RSCP
None
ADD
CELLSELRESEL(Optio
nal)
RNC
IdleQhyst1s
0~20
0~40, step:2
dB
ADD
CELLSELRESEL(Optio
nal)
RNC
IdleQhyst2s
0~20,255
{0~40}, {255},
step:2
dB
ADD
CELLSELRESEL(Optio
nal)
RNC
Treselection
s
0~31
0~31
ADD
CELLSELRESEL(Optio
nal)
RNC
HCSPrio
0~7
0~7
None
ADD
CELLHCS(Optional)
RNC
2013-02-06
HUAWEI Confidential
Page7, Total8
Document Title
Parameter
ID
Default
Value
Security Level
GUI Value
Range
Actual Value
Range
Unit
MML Command
NE
ADD
GSMCELL(Optional)
ADD
NRNCCELL(Optional)
Qhcs
20
0~99
0~99
None
ADD
CELLHCS(Optional)
ADD
GSMCELL(Optional)
ADD
NRNCCELL(Optional)
RNC
TpenaltyHc
sReselect
D0
ADD
INTRAFREQNCELL(O
ptional)
ADD
INTERFREQNCELL(O
ptional)
ADD
GSMNCELL(Optional)
RNC
TempOffset
1
D3
3, 6, 9, 12, 15,
18, 21,
INFINITY
dB
ADD
INTRAFREQNCELL(O
ptional)
ADD
INTERFREQNCELL(O
ptional)
ADD
GSMNCELL(Optional)
RNC
TempOffset
2
D2
2, 3, 4, 6, 8,
10, 12,
INFINITY
dB
ADD
INTRAFREQNCELL(O
ptional)
ADD
INTERFREQNCELL(O
ptional)
RNC
MCC
000~999
None
SET
MBMSPERF(Mandator
y)
RNC
MNC
00~99,
000~999
None
SET
MBMSPERF(Mandator
y)
RNC
2013-02-06
HUAWEI Confidential
Page8, Total8