Professional Documents
Culture Documents
Rock Failure Mechanisms
Rock Failure Mechanisms
Bits are designed to induce rock failure. Because rock failure can occur in different ways, depending
on the formation and on downhole conditions, there are a large number of design variations among
roller cone and fixed cutter bits. To evaluate these design variations and select a bit, we first need a
basic understanding of how rocks fail and how formation conditions affect drilling performance.
Elastic: If the applied stress is below the elastic limit of the material, the material
returns to its original shape and size once the stress is removed.)
Plastic: If the applied stress exceeds the material's elastic limit, the material
experiences permanent deformation; further stress increases result in additional
deformation.).
Above a certain stress limit, a material will rupture, or break. If it ruptures before significant plastic
deformation occurs, it is described as brittle. If it ruptures only after experiencing significant plastic
deformation, it is considered ductile. Under different conditions, the same material may exhibit either
brittle or ductile behavior.
Figure 1
Figure 2
Rock salt exhibits the same transition from brittle to plastic failure, but at much lower levels of
confining stress it becomes completely ductile and will flow at confining pressures of 800 psi and
greater.
Figure 3 (zero confining stress) and Figure 4 (3000 psi confining stress) illustrate the stress/strain
behavior of a cylindrical sample of porous limestone.
Figure 3
Figure 4
The value of P defines the hole condition as underbalanced, balanced or overbalanced ( Figure 5 ).
Each of these hole conditions, together with temperature and rate of deformation, affects rock failure
mechanisms, which in turn affect penetration rate.
Figure 5
Penetration rate is also affected by a pressure-related phenomenon known as chip hold-down. Chip
hold-down occurs when a mud filter cake or fine solids block fractures produced by the bit. This
prevents the liquid phase of the mud from invading the fractures, and results in a positive pressure
differential across the top surface of the chip. The hold-down force is equal to the area of the chip
times the differential pressure ( Figure 6 ).
Figure 6
Underbalanced Condition
If the pressure exerted by the fluid column is less than the pore pressure of the formation, the
differential pressure is less than zero, and the well is being drilled in an underbalanced condition.
This condition most often occurs when drilling with air, fresh water or muds weighing less than 8.6
lb/gal.
In underbalanced drilling, the rock exhibits brittle behavior it has a relatively low failure strength
and fractures very easily. Because the rock surface is in tension, it virtually explodes under the
compressive loads of the bit. There is no downward pressure to promote chip hold-down, and so
there is very little re grinding of already-drilled cuttings. This helps attain very high rates of
penetration.
Although its benefits are evident, underbalanced drilling is feasible only in areas where formation
fluids can be easily controlled and there is no danger of a blowout.
Balanced Condition
When the pressure of the fluid column is equal to the pore pressure, the hole is in
a balanced condition. This condition generally occurs when drilling with brine water or mud weighing
8.6 lb/gal.
Under balanced conditions, the rock is still in the brittle state and fractures relatively easily. The
bottom of the hole is in pressure equilibrium, so there is minimal stress concentration present to either
enhance or slow penetration rates. Penetration rates are generally slower than those experienced in
an underbalanced drilling, because there is some chip hold-down resulting from cohesive forces
between the rock cuttings, along with interference due to fluid viscosity.
Balanced drilling, like underbalanced drilling, presents blowout risks, and is an option only when there
is no likelihood of unexpected increases in formation pressure.
Overbalanced Condition
In overbalanced drilling, the pressure of the mud column exceeds the formation pore pressure. In
areas with normal pressure gradients, this condition occurs when the mud weight exceeds 8.6 ppg.
For safety reasons, overbalanced drilling is normal practice in most areas.
As the differential pressure increases in an overbalanced hole, the rock below the bit becomes
increasingly strong and ductile. The hole bottom is in a state of compression, thus retarding fracture
propagation caused by the bit. These factors, along with a high degree of chip hold-down, tend to
slow penetration rates. If the differential pressure is too high, the mud can fracture the formation,
resulting in lost circulation and possibly a blowout.
Differential pressures ranging from 2,000 to 6,000 psi are not uncommon in south Louisiana, south
Texas, the North Sea, the Middle East and other deep basins. The induced rock strength and large
chip hold-down forces created by these high differential pressures can make roller cone bits drill very
slowly in rocks that would normally be soft and easily drilled. A plot of penetration rate versus
differential pressure (Figure 7 ) shows the dramatic effect that increasing overbalance has on drilling
rates.
Figure 7
Rock sample:
Mud:
Circulation rate:
Mancos shale
Water-base, 10 lb/gal
320 GPM
Bits used:
" Smith F2
Bit nozzles:
Three (3),
diameter
Weight on bit:
35,000 lb
Rotary rpm:
80
The only condition that changed during this experiment was the differential pressure, which was 700
psi for the first set of bit runs, 1,200 psi for the second set of bit runs and 2,500 psi for the third set of
bit runs. Table 1 and Figure 8 summarize the test results.
P,
psi
ROP,
ft/hr
700
62
1200
2500
0 - 0.5
"
"
"
Figure 8
Note that with all other conditions held constant, the increase in differential pressure resulted in
dramatically reduced penetration rates and increased chip hold-down.
Normal drilling practice calls for maintaining mud weight 0.2 to 0.4 lb/gal higher than the equivalent
mud weight of the formation. While this practice provides a safety factor for well control, it can also
result in high differential pressures ( Figure 9 ) which, in turn, can severely limit drilling rates.
Figure 9
For example, using an 11 lb/gal mud at 14,000 feet in a well with a normal pressure gradient results in
a differential pressure of 1,700 psi, which places most shales and evaporites, as well as some
sandstones, into the plastic region. This results in much lower penetration rates than could be
attained in shallower formations with similar lithology.
A basic awareness of rock failure mechanisms and the effects of formation conditions allows us to
look more closely at the design features of roller cone and fixed cutter bits.