Professional Documents
Culture Documents
Fagor F1810 WFK1018 Washer SM Angl
Fagor F1810 WFK1018 Washer SM Angl
SERVICE
ASSISTANCE
Technical Study
t e c h n i c a l
PRODUCT:
RANGE:
Date: 25/02/2008
Document No.: 14538
t e c h n i c a l
Copyright by Fagor Electrodomsticos S.Coop. 2008. All rights reserved. The total
or partial reproduction of this document, by any procedure and on any type of media,
is prohibited without written authorisation from the holder of the usage rights. Breach
of this copyright will be pursued in conformity with applicable legislation and may lead
to criminal charges.
FAGOR ELECTRODOMESTICOS reserves the right to introduce, without prior
notification, any modifications to the characteristics of its manufactured products.
t e c h n i c a l
Table of contents
t e c h n i c a l
In order to avoid fire risk, electric shock, personal injury or other injuries when
using the washing machine, take the following precautions:
This washing machine is supplied with a manual that contains instructions on
operation, maintenance and installation. Read all the instructions before using the
washing machine.
Do not wash articles which have been previously cleaned, washed, soaked or treated
with gasoline, dry-cleaning solvents or other inflammable or explosive substances as
they produce vapours that may ignite or explode.
Do not add gasoline, dry-cleaning solvents or other inflammable or explosive substances
to the wash water since they produce vapours which may ignite orexplode.
Do not repair or replace any part of the washer, nor attempt any type of service unless
it has been recommended in the manuals maintenance instructions..
Do not stand or sit on the machine, or lean on the open loading door.
To reduce the risk of fire or electric shock, do NOT use an extension lead or adapter
to connect the washing machine to the mains electricity.
The machine must only be used for what it was designed.
Follow the washing instructions recommended by the manufacturer of the item to
bewashed.
Do not start the washing machine until you have made sure that:
All of the water connections, drainage, electricity and earthing comply with
local regulations and/or other applicable regulations.
t e c h n i c a l
Total power
FAGOR F-1810
TYPWM-900E3B
COD.905014763
N.080200001
2200W 220-230V-50Hz
10A.
4.9-98N/cm2
NIF ESF20020517
0905014763080200001
Washing machine
code (9 digits)
Month of manufacture
Year of manufacture
REGISTRATION PLATE
MAKE AND MODEL
TYPE OF APPLIANCE
SERIAL NUMBER
CAPACITY
BARCODE
t e c h n i c a l
Features
2.- Features
This range comprises of the following models:
Drawer for
detergent
Button
ON/OFF
Programme
selector
Start/pause
button
Spin + flot
button
Additional
functions
button
Time delay
button
1000
Stop
3h
6h
9h
700
400
AA
1 0 0 0 rpm
8 kg
Select
Wash programmes
For washing machines manufactured after 1st of May 2007
NORMAL
1 Normal cold
2 Fast 30C
3 Normal 30C
4 Normal 40C
5 Normal 60C
6 Pre-wash 60C
PROGRAMMES V1 circuits
DELICATE FABRICS
SPECIAL
7 Delicate Mixed 40C
10 Antibacterial 90C
8 Delicate cold
11 Eiderdown 30C
9 Delicate 30C
12 Curtains 30C
13 Hand wash
14 Quick (15 minutes)
15 Rinses
16 Spin
LB6W302A1 Circuit
t e c h n i c a l
Description of operation
Spin
The wash options must always be selected after selecting the wash programme.
Any change to the programme carried out during
the selection cancels the options which were
1000
700
previously selected.
Stop
3h
6h
9h
400
Select
1000
Stop
3h
6h
9h
700
400
Select
1000
700
1000
400
700
Stop
3h
6h
9h
Stop
3h
6h
9h
400
Select
Select
1000
Stop
3h
6h
9h
700
400
Select
To cancel the delay, press the time delay button until the pilots indicating the delay
go off. Changing to another programme also cancels the delay.
Start
Start/Pause button
a) To start the washing machine you must press the
start/stop key.
t e c h n i c a l
Description of operation
Additional functions
Button for selecting additional functions according to programmes.
There are 2 options: anti-crease and intensive wash.
Press the button to display the required option.
By pressing several times, you can choose
between various combinations of one or two
additional functions at the same time, depending
on the chosen programme.
1000
Stop
3h
6h
9h
700
400
Select
Key: Anti-crease
This stops at the final rinse, leaving the clothing floating in water. When the function is
deactivated, the washer continues the programme, draining and spinning.
This is used when you are not at home, for example, to delay the spin until you have
arrived so that creases are not caused by the clothes being spun and then left in
the drum.
Key: Intensive Wash
This option, specially recommended for very dirty or stained garments, gives better
results by lengthening the wash cycle.
Programme progress
a current programme phase.
When the programme is running, the pilot lights indicate the
1000
Stop
3h
6h
9h
700
400
Select
Important: If, during the wash cycle, the programme is changed using the selector,
the washer is left in the PAUSE state, and the programme is canceled. To add or
remove an article, press the start/pause button and make sure that the water is not
above the door overflow level, and that the interior temperature is not high. Press the
start/pause button again to re-start the washer from the same phase of the cycle in
which it was stopped.
t e c h n i c a l
Description of operation
Power failure
When the supply returns after a power failure, the washer continues to work as normal,
from the point at which it stopped (its memory lasts a few hours).
The same thing happens if the ON/OFF button is pressed.
Warnings
To reduce the noise level of the spin cycle: use the adjustable feet to level the washer.
Aim to wash clothes of different sizes in the same wash programme, for a better
weight distribution in the drum when spinning.
All the models have a spin cycle safety system, which prevents them spinning if the
distribution of the clothes in the drum is very uneven. This prevents excessive vibration.
If at any time the clothes have not been correctly spun, spread them out more evenly
in the drum, and spin again.
t e c h n i c a l
Description of operation
3.- Description of operation
3.1.- General description
3.1.1.- Component characteristics
Component
Motor
1250 RPM
4(%2-)#
02/4%#4/2
2
4'
34!4/2
4(%2-)#
02/4%#4/2
4'
34!4/2
4(%2-!,
02/4%#4/2
4(%2-!,
34!4/2
02/4%#4/2
4'
34!4/2
Door lock
Function
Used in machines
with variable spin,
and makes rotating
movements when
washing and spinning.
Motor power supply:
- Clockwise, power
220 V., contacts 2
and3. Bridge between
contacts 5 and 6.
- Anti-clockwise, power
220 V. , contacts 3
and5. Bridge between
contacts 2 and 6.
Features
Voltage: 220 v / 50 Hz
Stator resistance: 1.3
Rotor resistance: 1.7
Tachogenerator resistance:
184
Tachogenerator voltage:
1.2v / 1,000 rpm
Used in machines
with variable spin,
and makes rotating
movements when
washing and spinning.
Motor power supply:
- Clockwise, power
220 V, contacts 4
and5. Bridge between
contacts 3 and 6.
- Anti-clockwise, power
220 V, contacts 4
and6. Bridge between
contacts 5 and 3.
Voltage: 220 v / 50 Hz
Stator resistance: 3.3
Rotor resistance: 2.46
Tachogenerator resistance:
90
Voltage: 220 v / 50 Hz
16 Amp.
Delay of between 40 and
75 seconds.
4'
t e c h n i c a l
Description of operation
Component
Door lock with
instantopening
Function
Hatch closing
Manual opening for use
in case of electricity
supply failure
Recirculation pump
Double connectorised
electrovalve
Pressure switch
Features
Voltage: 220-240 v / 50 Hz
Drainage pump resistance
170
Recirculation pump
resistance 180
Both have a thermal
protector
Power 30 W
Allows water intake in
Voltage: 220-240 V /50 Hz
the pre-wash, wash and Power: 5 W
rinse phases
Flow: 6.7 litres / minute
EV1 pre-wash orange
Pressure: 0.5-10 kg / cm
connector
Resistance: R1=R2=R3=
EV2 wash black
3.7K
connector
3/4 Thread Gas
EV1 + EV2 additive
12mm conduit diameter
intake
Level 1
102 / 72 3
Overflow safety device
310 10
12
11
14
16
11 Common
12 Water inlet
14 Heating
16 Overflow
t e c h n i c a l
Description of operation
Component
Heating resistance
Function
Heating element
+ thermofuse
incorporated into the
element itself
Thermofuse cut-out
temperature165C
V1 electronic circuit
Features
Resistance: 26.4
Material: Austenitic
stainless steel
Power: 2022 W
Voltage: 230 v
NTC 30C variable
resistance value 9786
Voltage: 220 v / 50 Hz
Important: It is necessary
to configure the circuit
before starting the machine.
(follow configuration
instructions)
t e c h n i c a l
Description of operation
3.1.2.- Configuration of the V1circuits
1000
Stop
3h
6h
9h
700
400
AA
1 0 0 0 rpm
8 kg
Select
* Speed: press the speed button until the LED or LEDs match the sticker.
* Cold water: Press the time delay button. The LED must be off.
* RH: press the Select button until the Flot and Intensive LEDS light up.
7. To confirm the configuration, press the Start/Pause button until the Skip Spin Option,
Time Delay and Select LEDs start to flash.
10
t e c h n i c a l
Description of operation
3.1.3- T.S.S. Programme
1000
Stop
3h
6h
9h
700
400
AA
1 0 0 0 rpm
8 kg
Select
SELECTION MODE
TIME (APPROX.)
WASH
10 sec.
RINSES
Emptying + Spin
5 min.
STOP
Pressure switch
level
EXTRA
RINSE
40C
INTENSIVE
Water input via pre-wash, wash and softener electricallyoperated valves + Recirculation
5 sec.
Drainage Pump
30 sec.
11
12
UNBALANCED
WARNING
MOTOR
INVERSION
FAULT
MOTOR
DOES NOT
HEATUP
CHECK
The drum rotation direction does not change until the motor stops
(max. time 2 min.)
Wash, rinse, STOP and extra intensive rinse LEDs flashing
< 5C/15min.
(Except in reliability program)
Wash, rinse, STOP and SKIP spin (0) LEDs flashing
OVERFLOW
NTC
EB ON 6min.
and PN ON (full). Rinse and STOP LEDs flashing
FAULTS
ACTION
IN USER PROGRAMME
STOP (Programme end)
ACTIONS
RESET
The same as the previous ones but with the door lock
activated
T.S.S. programme fast forward function: Press the start / pause button to move to another step in the programme without first having to finish the step.
EMPTYING
DOOR OPEN
FILLING
SAFETY
MECHANISMS
t e c h n i c a l
Description of operation
T.S.S. SPIN
SEC.
SEC.
EXTRA SPIN
SEC.
SEMI-DELICATE SPIN
SEC.
SEC.
SEC.
DELICATE SPIN
NORMAL SPIN
NON-DETECTION
OF OVERFLOW AREA
ANTI-CLOCKWISE
CLOCKWISE
SUPER SPIN
SEC.
SPIN PLUS
SEC.
SEC.
t e c h n i c a l
Description of operation
Wash vibrations
13
IMBALANCE TEST
IMBALANCE TEST
MACHINE MODEL
RPM
selector
Easy iron
t e c h n i c a l
Description of operation
Spin vibrations
14
15
Step 0
Step 3
Step 2
Step 1
Step 4
Step 5
Step 6
Step 7
IMBALANCE TEST 1, 2, 3
According to programme
SEC.
MACHINE MODEL
t e c h n i c a l
Description of operation
Normal spin:
t e c h n i c a l
Description of operation
3.1.5.- Spin attempts
If the washing machine detects the unequal balance of clothes in the spin cycle it will
follow this process:
The total number of attempts to start spinning is 20, divided according to these criteria.
In the first 6 attempts, the maximum unbalanced limit allowed is 550 g.
Between the 7th and 18th attempts the maximum unbalanced limit allowed is 800 g
and the final speed is less than the nominal speed, for example a washing machine
of 1,200 rpm will spin at 1,000 rpm.
For the 19th and 20th attempts, the maximum unbalanced limit allowed is 1,500 g,
and the final spin speed will be 650 rpm, except in washing machines with a nominal
speed of 700 rpm, which will spin at 400 rpm.
These attempts to reposition the clothes in the drum will increase the total programme
time by 20 minutes.
The LCD screen will display CO3. This is not considered a fault, it merely warns the
user about the security measure the circuit has detected.
If an imbalance is detected in the rinse phase the number of attempts will not exceed 3.
In 8 kg washers dating from after 01/11/2007, the number of imbalance correction
attempts is reduced by half (9 attempts).
16
t e c h n i c a l
Description of operation
3.2.- Drawings and diagrams
17
t e c h n i c a l
E.V.2 WASH
PRESSURE SWITCH
FILTER
E.V.1 PRE-WASH
Description of operation
RESISTANCE
FUSE
AMAGREEN
DOOR LOCK
DRAIN
PUMP
RECIRCULATION
PUMP
AMAGREEN
MOTOR
18