Professional Documents
Culture Documents
MeasurIT FCI Application Data Sheet Flow Meter MT86 MT91 0908
MeasurIT FCI Application Data Sheet Flow Meter MT86 MT91 0908
MeasurIT FCI Application Data Sheet Flow Meter MT86 MT91 0908
U-Length = ID + B + E
(Convert to inches and enter into OIS boxes 9 through 12)
Craan, Craanford, Gorey, Co. Wexford, Ireland
email: info@measurIT.com, www.measurIT.com
phone: +353 (0) 53 942 8962, fax: +353 (0) 53 942 8963
measurIT technologies
(Convert to inches and enter into OIS boxes 9 through 12) For S Sensor Types Only:
Y = Distance from pipe inside wall to sensing point centerline. (Y = 0.146 x ID).
Z = Distance from sensing point center line to the end of the flow element. (Z = 1.0 in.
[25 mm] for standard temperature instruments and 0.75 inch. [19 mm] for the high
temperature.)
The 2-point configuration show is typically used for 16-inch diameter pipes or larger.
For 36-inch diameter pipes or larger, 3 or 4-point configurations are recommended. (Use
the same factor for calculating “Y” and space the flow elements evenly around the
circumference of the pipe (120 o or 90o apart, respectively.)
2 Address
3 City
4 County
5 Contact Person
6 Title or Department
7 Telephone Number / Extension ( )
8 Fax Number ( )
9 E-mail Address
10
11 Loop or Branch number
Service or Application
PROCESS PIPING DATA
12
13 Pipe or Duct Size / Schedule
14 Wall Thickness
15 Piping Cross-Section Geometry Round Square Rectangle
16 Material
17 Pipe Orientation / Flow Direction Horizontal Vertical, Flow Up Vertical, Flow Down
18 Flow Element Mounting Side Top Bottom
19 Flow Element Process Connection
20
Gas Composition Gas Percent (%)
21 % Volume (moles)
PROCESS MEDIA DATA
22 % Weight (mass)
23
24
25 (Total must add up to 100%)
Minimum Nominal Maximum
26 Operating Temperature
27 Conditions Pressure
28 Flow Rate
29
30 Tag Number(s)
Output Configuration Output #1 Output #2
31 Parameter Flow rate Temperature Flow rate Temperature
SPECIFICATIONS
FLOWMETER
INSTALLATION DIAGRAM
Upstream Distance * Downstream Distance *
F E
Upstream Disturbance * Downstream Disturbance *
MT Flow Element
* How far away are the nearest upstream and downstream flow disturbances and what are they (e.g.; elbow, reducer, tee, valve, blower, etc.)
measurIT technologies Application Data Sheet (ADS)
Craan, Craanford, Gorey, Co. Wexford, Ireland
email: info@measurIT.com, www.measurIT.com
MT86 & MT91
phone: +353 (0) 53 942 8962, fax: +353 (0) 53 942 8963 Insertion Multi-Point Mass Flowmeter
MT Type Code 6.- 8. Process Codes 13. Process Transmitter Options 19. Cable Jacket Notes
Connection 6 7 8 Orientation Code and Length 6 Code
1. Must specify Code 1 in
Analog design; 86 16. Input Power and Box 3.
8 sensing points “M” Sensor For Horizontal Display Code PVC
maximum Configuration Only Pipe or Duct 220°F [104°C] 2. All coatings are over 316
Stainless steel sensors and
All flow assemblies A MT86 without Display maximum temperature assemblies. Only available
Microproces sor 91 2 inch Male NPT N 2 0
based; 16 sensing with Right to Left flow with flange mounted, fixed
100 to 130 Vac 1 10 feet [ 3 m] A insertion length
points maximum ¤ 3 inch, 150 lb Flange 3 F 3 G All flow assemblies B configurations.
per material in Box 5 200 to 270 Vac 2
with Left to Right flow ¤ 50 feet [15 m] B 3. FCI supplied flanges are
¤ 24 Vdc 3 raised face, phonographic
1. Sensor Half flow assemblies C
Configuration Code
“S” Sensor
Configuration Only
with Right to Left flow, ¤ 90 to 110 Vac 4 ¤ 100 feet [30 m] C serrated.
and half with Left to 4. Customer supplied or
Right flow MT86 with Display Teflon 7 specified flange shall be
Two or more sensing M 1 inch Male NPT N1 0
points per flow For Vertical 100 to 130 Vac 5 350°F [177°C] per ANSI or DIN
maximum temperature
element assembly ¤ 1 1/2 inch, 150 lb F BG Pipe or Duct
200 to 270 Vac 6
specifications and shall be
no smaller than 1-1/2
Flange per material inches [DN40] for the “S”
One sensing point S in Box 5 3 Flow up D ¤ 24 Vdc 7 10 feet [ 3 m] E
per flow element Sensor Type or 3 inches
Flow down E
assembly 1
Low Pressure
¤ 90 to 110 Vac 8 ¤ 50 feet [15 m] F [DN80] for the “M” Sensor
Type.
¤ Other * Packing Gland with Customer specified W MT91 with Display
¤ 100 feet [30 m] G 5. Available with MT91 only.
Graphite Material 85 to 265 Vac A
50 psig [3.5 bar(g)] 6. Cable length required for
2. Sensor maximum 14. Local ¤ Other * ¤ Customer specified W each sensing point.
Assembly Code Enclosure Code 7. Teflon is standard for high
¤ 1 1/4 inch Male NPT P A 0 temperature (Box 4,
“M” Sensor 17. Output No. 1 Code Code H).
Number of flow 1 20. Identification TagCode
element assemblies 2 ¤ Flange 3 (select Q Configurations Only 8. Tag can have 5 lines with
3 Codes for 7 and 8 MT86 18 characters per line.
Carbon steel; G Adhesive label A
4 from Tables A and B) 4-20 mA A
5 NEMA Type 4 ¤ Label and8 stainless B 9. Available with “S” Sensor
6 Medium Pressure ¤ 4-20 mA isolated E steel tag Type only due to gas type.
7 Packing Gland with ¤ Aluminum; L 10.Customer specified
8 Graphite Material hazardous locations ¤ 0-10 Vdc B ¤ Customer specified W calibration cannot exceed
500 psig [35 bar(g)] Groups B, C, D, E, F the maximum operating
and G MT91
maximum temperature and pressure
3. Sensor Points Code Field configurable, 1 21. Calibration of the MT Series
¤ 1 1/4 inch Male NPT R A 0 “S” Sensor dual analog outputs Code 1: Code configuration.
Number of sensing 1 Configurations Only Application
¤ Other 11. If Code D is selected in
points per flow 2 ¤ Flange 3 (select T *
Air; standard range, T Table A, Code S must be
element assembly 3 Codes for 7 and 8 Aluminum; D selected in Table B.
4 from Tables A and B) NEMA Type 4X and 18. Output No. 2 Code wind tunnel, flat
5 hazardous locations profile
6 Groups B, C, D, E, F
7
“M” or “S” Sensor
and G, EEx d IIC MT86 ¤ Air equivalency C
Configurations (Flue gas, waste gas
8 (meets IP66) None 0 etc.)
¤ Flange 3 (select F
¤ 300 Series stainless J ¤ 4-20 mA A
4. Process Codes for 7 and 8 ¤ Nitrogen, helium, E
Temperature Code from Tables A and B) steel; NEMA Type 4X ¤ 4-20 mA isolated E argon, carbon dioxide,
and hazardous or nitrous oxide 9
Range locations Groups B, ¤ 0-10 Vdc B
¤ Customer supplied F S W
C, D, E, F and G, ¤ Hydrocarbons F
-40° to 350° F S 4
flange ¤ DPDT relay with C (natural gas,
EEx d IIC (meets IP66) 2 amp contacts
[-40° to 177° C] methane, ethane,
¤ Flow element with propane, etc.) 9
¤ -40° to 850° F 9.- 12. Insertion Length ¤ Other * D
H fault alarm ¤ Hydrogen or G
[-40° to 454° C] hydrogen mixture 9
MT91
¤ Other * • Field configurable 2 ¤ Customer specified 10 W
with dual alarms
9 10 11 12
5. Material of ¤ Other * 22. Calibration
Construction Code See Installation drawings
to specify dimension in Code 2: Code
Setup
316 Stainless steel, A inc hes to the nearest 15. Remote
nickel braze per tenth of an inc h. Div ide Enclosure Code
millimeters by 25.4 to None 0
AMS 4777
conv ert to inches. No enclosure; P ¤ Temperature A
“M“ Sensor panel mounted compensation
Confguration Only circuit board
Table A Table B ¤ Vortab flow C
¤ 316 Stainless steel, E Carbon steel; G conditioner
nickel braze with 7. Flange Size Code NEMA Type 4
all wetted parts
8. Flange Material
and Rating Code
¤ Temperature F
nickel coated 2 1 1/2 inch9 B ¤ Aluminum; M compensation and
Vortab flow
150 lb. per G hazardous locations
¤ 316 Stainless steel, F 2 inch 9 2 material in Box 5 Groups D, E, F and G
conditioner
nickel braze with
150 lb. Carbon steel A
all wetted parts
Chromium Carbide
3 inch 3 ¤ DIN/EIN rack
5
R
300 lb. per H assemby
coated 2 4 inch 4 material in Box 5
“S“ Sensor Flat duct flange 11 D 300 lb. Carbon steel B ¤ Other *
Confguration Only
300 Series stainless S
¤ Hastelloy C C Customer specified 4 W steel (duct flange) 11