Professional Documents
Culture Documents
C Node Timing
C Node Timing
PROVISIONING
F2880_B10
PROVISIONING
VALUES
DESCRIPTION
System/Bypass
Timing Source
Force/Auto
Mode
Auto Reserved DNU
0 thru 255
0 thru 1800
Group ID
Hold off Time
(ms)
WTR Time
0 thru 7200
(sec)
Priority
1 thru 256
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
VALUES
DESCRIPTION
System/Bypass
(list box)
Lockout
(Check Box)
Forced Switch
Manual Switch
F2880_B10
PROVISIONING
6. Click the Close button. The Set Clock Extra Commands dialog disappears
and the Setup-Timing Source Configuration dialog box is displayed again.
7. In the Setup-Timing Source Configuration dialog box, perform one of the
following:
x To forward the NE setup, click the Next button to open the Setup-Timing
Source Attribute dialog box. Then go to the subsection 4.2.6 Setup NE
Clock Module Configuration.
x To go back to the NE slot configuration setup, click the Back button to return
to the Setup-Physical Slot Configuration dialog box.
x To cancel and quit the NE setup, click the Close button.
This step is the end of the procedure.
F2880_B10
PROVISIONING
VALUES
DESCRIPTION
Recoverability
(Check Box:
Revertive )
Switching Criterion
Priority/SSM
F2880_B10
PROVISIONING
(Contd)
ITEM/PARAMETER
VALUES
Timing Source
Threshold
DESCRIPTION
Select the timing source threshold.
When starting up the SSM protocol, the
timing source cannot be used as the
reference clock if its QL priority is lower
than the setting value.
(not a selection)
Working Timing
(not a selection)
(not a selection)
(not a selection)
Lock
Source Subrack
Working Timing
Source Slot
Working Timing
Source Port
Working Mode
Holdover
Freerun
(not a selection)
F2880_B10
PROVISIONING
F2880_B10
PROVISIONING
x To forward the NE setup, click the Next button to open the Setup-Others
dialog box. Then go to the subsection 4.2.7 Complete NE Setup.
x To go back to the timing source configuration setup, click the Back button to
return to the Setup-Timing Source Configuration dialog box.
x To cancel and quit the NE setup, click the Close button.
This step is the end of the procedure.
F2880_B10
PROVISIONING
Procedure
1. Confirm that the Setup-Others dialog box shown in Figure 4-9 is displayed:
Figure 4-9.
2. Click the Download check box (leaving a tick) to download any data to the NE.
NOTE: To configure NE, Download check box must be checked.
3. Adjust the system time in the Time Adjusting field, if necessary.
4. Confirm the settings, and perform one of the following:
x To modify any settings for NE setup again, click the Back button to go back
to the Setup-Timing Source Attribute dialog box.
x To complete the setting for NE setup (initialization), click the End button.
x To cancel and quit the NE setup, click the Close button.
This step is the end of all the procedures for NE setup operation.
F2880_B10
PROVISIONING
ITEM/PARAMETER
DESCRIPTION
NOTE
Slot ID
(not selected)
Port ID
(not selected)
SANBIT
(not selected)
Output Status
(not selected)
Timing Source
(not selected)
(drop-down list)
Setting:
Output Status
(drop-down list)
Setting:
Squelch
(drop-down list)
Threshold
Setting:
SANBIT
F2880_B10
PROVISIONING
Figure 4-10.
F2880_B10
PROVISIONING
DESCRIPTION
Board
(drop-down list)
NO.
(not selected)
(not selected)
(not selected)
Status
(not selected)
(drop-down list)
Type
NOTE
F2880_B10
PROVISIONING
DEFINITION
Port for fan board
NOTE
FAN_1: fan board
FAN_2: fan board with alarm port
02
03
04
F2880_B10
PROVISIONING
Figure 4-11.