Professional Documents
Culture Documents
Old and New DIN
Old and New DIN
Old and New DIN
Over the years, many DIN standards were integrated into the ISO standards, and thus also a part of the EN
standards. In the cource of the revision of the European standards serveral DIN standards were withdrawn and
replaced by DIN ISO EN and DIN EN.
The standards used in the past such as the DIN 17121, DIN 1629, DIN 2448 and the DIN 17175 have since
been mostly replaced by Euronorms. The Euronorms clearly distinguish the pipe's area of application.
Consequently different standards now exist for pipes used as construction materials, pipelines or for mechanical
engineering applications.
This distinction was not as clear in the past. For example, the old St.52.0 quality was derived from the DIN
1629 standard which was intended for pipeline systems and mechanical engineering applications. This quality
was also often used for steel structures, however.
The info below explains the main standards and steel qualities under the new system of standards.
The EN 10216 comprises several parts. The parts that are relevant to us are as follows:
EN 10216 Part 1: non-alloy pipes with specified properties at room temperature
EN 10216 Part 2: non-alloy pipes with specified properties at higher temperatures
EN 10216 Part 3: alloy pipes made from fine-grained steel for any temperature
Some examples:
1.
2.
EN 10216-2, Quality P235 GH (formerly DIN 17175, St.35.8 Cl. 1, boiler pipe)
P = Pressure
235 = minimum yield strength in N/mm2
GH = tested properties at higher temperatures
3.
* Normalized is defined as: normalized (warm) rolled or standard annealing (at a min temperature of 930C).
This applies to allqualities designated by the letter 'N' in the new Euro Standards.
New
Execution
Norm
Steel grade
Execution
Norm
Steel grade
Welded
DIN 1626
St.37.0
Welded
DIN EN 10217-1
P235TR2
Welded
DIN 1626
St.52.2
Welded
DIN EN 10217-3
P355N
Seamless
DIN 1629
St.37.0
Seamless
DIN EN 10216-1
P235TR2
Seamless
DIN 1629
St.52.2
Seamless
DIN EN 10216-3
P355N
Seamless
DIN 17175
St.35.8/1
Seamless
DIN EN 10216-2
P235GH
Seamless
ASTM A106*
Grade B
Seamless
DIN EN 10216-2
P265GH
Seamless
ASTM A333*
Grade 6
Seamless
DIN EN 10216-4
P265NL
* ASTM standards will remain valid and will not be replaced by Euronorms in the near future
DIN EN 10216-2
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non alloy and alloy steel
tubes with specified elevated temperature properties; German version EN 10216-2:2002+A2:2007
The document specifies the technical delivery conditions in two test categories for seamless tubes of circular
cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
DIN EN 10216-3
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes
Specifies the technical delivery conditions in two categories for seamless tubes of circular cross section, made
of weldable alloy fine grain steel...
DIN EN 10216-4
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 4: Non-alloy and alloy steel
tubes with specified low temperature properties
Specifies the technical delivery conditionsin two categories for seamless tubes of circular crossection, made with
specified low temperature properties, made of non-alloy and alloy steel...
DIN EN 10216-5
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes;
German version EN 10216-5:2004, Corrigendum to DIN EN 10216-5:2004-11; German version EN 102165:2004/AC:2008
This Part of this European Standard specifies the technical delivery conditions in two test categories for
seamless tubes of circular cross-section made of austenitic (including creep resisting steels) and austeniticferritic stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at
low temperatures or at elevated temperatures. It is important that the purchaser, at the time of enquiry and
order, takes in account the requirements of the relevant national legal regulations for the intended application.
DIN EN 10217-1
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with
specified room temperature properties
This Part of EN 10217 specifies the technical delivery conditions for two qualities TR1 and TR2 of welded tubes
of circular cross section, made of non-alloy quality steel and with specified room tempe...
DIN EN 10217-2
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric welded non-alloy and
alloy steel tubes with specified elevated temperature properties
Specifies the technical delivery conditions in two test categories of electric welded tubes of circular cross
section, with specified elevated temperature properties, made of non-alloy and alloy steel...
DIN EN 10217-3
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes
Specifies the technical delivery conditions for welded tubes of circular cross section, made of weldable non-alloy
fine grain steel...
DIN EN 10217-4
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 4: Electric welded non-alloy steel
tubes with specified low temperature properties
Specifies the technical delivery conditions in two test categories of electric welded tubes of circular cross
section, with specified low temperature properties, made of non-alloy steel...
DIN EN 10217-5
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 5: Submerged arc welded nonalloy and alloy steel tubes with specified elevated temperature properties
Specifies the technical delivery conditions in two test categories of submerged arc welded tubes of circular cross
section, with specified elevated temperature properties, made of non-alloy and alloy...
DIN EN 10217-6
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded nonalloy steel tubes with specified low temperature properties
Specifies the technical delivery conditions in two test categories of submerged arc welded tubes of circular cross
section, with specified low temperature properties, made of non-alloy steel...
DIN EN 10217-7
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes
Specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made
of austenitic and austenitic-ferritic stainless steel which are applied for pressure...
New
Execution
Norm
Steel grade
Execution
Norm
Steel grade
Welded
DIN 17120
St.37.2
Welded
DIN EN 10219-1/2
S235JRH
Welded
DIN 17120
St.52.3
Welded
DIN EN 10219-1/2
S355J2H
Seamless
DIN 17121
St.37.2
Seamless
DIN EN 10210-1/2
S235JRH
Seamless
DIN 17121
St.52.3
Seamless
DIN EN 10210-1/2
S355J2H
DIN EN 10210-2
Hot finished structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and
sectional properties
This part of EN 10210 specifies tolerances for hot finished circular, square, rectangular and elliptical structural
hollow sections, manufactured in wall thicknesses up to 120 mm, in the following siz...
DIN EN 10219-1
Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery
conditions
This part of this European Standard specifies the technical delivery conditions for cold formed welded structural
hollow sections of circular, square or rectangular forms and applies to structural hol...
DIN EN 10219-2
Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions
and sectional properties
This part of EN 10219 specifies tolerances for cold formed welded circular, square and rectangular structural
hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size range...
New
Execution
Norm
Steel grade
Execution
Norm
Steel grade
Welded
API 5L
Grade B
Welded
DIN EN 10208-2
L245NB
Welded
API 5L
Grade X52
Welded
DIN EN 10208-2
L360NB
Seamless
API 5L
Grade B
Seamless
DIN EN 10208-2
L245NB
Seamless
API 5L
Grade X52
Seamless
DIN EN 10208-2
L360NB
* API standards will remain valid and will not be replaced by Euronorms in the near future
DIN EN 10208-2
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement
class B
This European Standard specifies the technical delivery conditions for seamless and welded steel pipes for the
on land transport of combustible fluids primarily in gas supply systems but excluding pip...
DIN EN 10208-3
Steel pipes for pipe lines for combustible fluids - Technical delivery conditions - Part 3: Pipes of class C
Specifies the technical delivery conditions for unalloyed and alloyed (except stainless) seamless and welded
steel pipes. It includes quality and testing requirements overall higher than those specifi...
DIN EN 10253-1
Butt-welding pipe fittings - Part 1: Wrought carbon steel for general use and without specific inspection
requirements
The document specifies requirements for steel butt-welding fittings, namely elbows and return bends,
concentric reducers, equal and reducing tees, dished and caps.
DIN EN 10253-2
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements;
German version EN 10253-2
This European Standard specifies in two parts the technical delivery conditions for steel butt welding pipe
fittings (elbows, return bends, concentric and eccentric reducers, equal and reducing tees, and caps) which are
intended for pressure purposes and for the transmission and distribution of fluids and gases. The part 1 covers
fittings of unalloyed steels without specific inspection requirements. The part 2 covers fittings with specific
inspection requirements and offers two ways for determining the resistance to internal pressure of the fitting.
DIN EN 10253-3
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without
specific inspection requirements; German version EN 10253-3
This part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding
fittings made of austenitic and austenitic-ferritic (duplex) stainless steels and delivered without specific
inspection.
DIN EN 10253-4
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with
specific inspection requirements; German version EN 10253-4
This European Standard specifies the technical delivery requirements for seamless and welded butt-welding
fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and
austenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at
room temperature, at low temperature or at elevated temperatures. It specifies: the type of fittings, the steel
grades, the mechanical properties, the dimensions and tolerances, the requirements for inspection and testing,
the inspection documents, the marking, the handling and packaging.
NOTE: In the case of a harmonised supporting standard for materials, presumption of conformity to the
Essential Requirement(s) (ESRs) is limited to technical data of materials in the standard and does not presume
adequacy of the material to a specific item of equipment. Consequently the technical data stated in the material
standard should be assessed against the design requirements of this specific item of equipment to verify that
the ESRs of the Pressure Equipment Directive (PED) are satisfied. Unless otherwise specified in this European
Standard the general technical delivery requirements in DIN EN 10021 apply.
DIN EN 1092-1
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN designated - Part 1:
Steel flanges; German version EN 1092-1:2007
This European standard specifies requirements for circular steel flanges in PN designations PN 2,5 to PN 400
and nominal sizes from DN 10 to DN 4000. This standard specifies the flange types and their facings,
dimensions, tolerances, threading, bolt sizes, flange face surface finish, marking, materials, pressure /
temperature ratings and flange masses.
DIN EN 1092-2
Circular flanges for pipes, Valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
The document specifies requirements for circular flanges made from ductile, grey and malleable cast iron for
DN 10 to DN 4000 and PN 2,5 to PN 63. It also specifies the types of flanges and their facings, dimensions and
tolerances, bolt sizes, surface finish of jointing faces, marking, testing, quality assurance and materials together
with associated pressure/temperature (p/T) ratings.
DIN EN 1092-3
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN designated - Part 3:
Copper alloy flanges
This document specifies requirements for circular copper alloy flanges in PN designations from PN 6 to PN 40
and nominal sizes from DN 10 to DN 1800.
DIN EN 1092-4
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN designated - Part 4: