Professional Documents
Culture Documents
SCX500 Manual
SCX500 Manual
SCX500 Manual
user manual
DIMENSIONS
All dimensions are in millimeters
442
178
364
138
200
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mania SCX500 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rigging the Mania SCX500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Focus adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Creating a data link for DMX and master/slave operation . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Auto trig operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Music trig operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Master/slave operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DMX controller operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Inverting pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Firmware /hard boot uploads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Mania SCX 500 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1. INTRODUCTION
Thank you for selecting the Martin Mania SCX500. This automated
moving-mirror projector has the following features:
Automatic triggering and music triggering modes
Stand-alone single fixture and master/slave operation, both with auto
trig and music trig
DMX controllable, choice of 6- or 8-channel DMX control modes
12 pre-programmed macros
15 full colors (including white) and 5 multi-colors. Split color feature for
added color capability
16 gobos
180 pan and 72 tilt
Adjustable focus
15 beam angle
150 watt long-life halogen lamp
Versatile mounting options
Unpacking
The packing material is carefully designed to protect the fixture during
shipment - always use it to transport the fixture.
The Mania SCX500 is supplied with:
Lamp (installed)
Power cable
5 meter (16.4 ft.) RS-485 XLR cable for data link
User manual
Mounting U-bracket and mounting plate
Fasteners for U-bracket and mounting plate
Introduction
DMX out
Swivel lock
Main fuse
DMX in
Power input
Power indicator
DMX Address
X100
X10
X1
Mode
Safety information
Warning!
2. INSTALLATION
AC power
The Mania SCX500 is supplied set up to match local voltage and
frequency. The factory setting is shown on the serial number label. It is not
possible to reconfigure the Mania SCX500 to accept any other voltage or
frequency than those stated on the serial number label.
Warning!
For protection from fire and electric shock, the fixture must be
grounded (earthed). The power supply must have overload
and ground-fault protection.
Check that power cables are undamaged and rated for the
current requirements of all connected devices before use.
Check the operating voltage and frequency indicated on the
serial number label before applying power. If your Mania
SCX500 does not match your local AC power, do not use it.
Pin
Marking
Screw color
brown
live
yellow or brass
blue
neutral
silver
yellow/green
ground
green
Installation
Block access below the work area and work from a stable
platform when installing or servicing the fixture.
Always use a secure means of secondary attachment that can
hold at least 10 times the weight of the fixture.
1. The fixture must be located at least 1 meter (3.3 ft.) away from the
surface to be illuminated and at least 0.1 meters (4 in.) from any
combustible materials (wood, fabric, paper, etc.). Ensure that the
clearance around the fan and air vents is at least 0.1 meters (4 in.).
Ensure that there are no flammable materials nearby.
2. If using a rigging clamp (not included), ensure that the clamp is
undamaged and can bear at least 10 times the fixtures weight. Bolt the
clamp securely to the fixtures mounting bracket with a grade 8.8
(minimum) M12 bolt and lock nut through the 13 mm hole in the center
of the mounting bracket, or as recommended by the clamp
manufacturer.
3. If fastening the fixture directly to a mounting surface, ensure that any
fasteners used and the mounting surface can bear at least 10 times the
fixtures weight. The fixture may be fastened using any of the following:
four 6.5mm holes in the sides of the U-bracket
two 8mm holes in the top of the U- bracket
one 13mm hole in the top of the U-bracket.
10
4. Ensure that the structure used to support the fixture can support at
least 10 times the total weight of all installed fixtures, clamps, cables,
auxiliary equipment, etc.
5. Install a safety wire that can hold at least 10 times the weight of the
Safety wire attachment
point
Installation
11
6. Loosen the swivel locks and tilt the fixture to the desired angle. Turn the
swivel locks clockwise to tighten. Check that both swivel locks are tight
and that the fixture is securely clamped in position.
Focus adjustment
The focus adjustment screw is next to the lens aperture. Do not confuse it
with the cover release screw.
Focus
adjustment knob
Lamp module
cover release
thumbscrew
Do not look directly into the light beam while adjusting the focus.
applications. Your Martin dealer can supply suitable high quality cable in
various lengths.
3-pin to 5-pin
Adaptor
Male
Female
Male
Female
Male
Female
1
2
3
4
5
1
2
3
1
2
3
1
2
3
4
5
1
2
3
1
2
3
P/N 11820005
3-pin to 3-pin
Phase-Reversing
Adaptor
P/N 11820004
P/N 11820006
Male
Termination Plug
Female DMX
Termination Plug
Male XLR
Female XLR
1
2 120 Ohm
3
P/N 91613017
1
2
3 120 Ohm
P/N 91613018
Installation
13
3. OPERATION
Important! Each time you power the Mania SCX500 off, wait at least 10
seconds before powering on again. Failure to do so may cause
damage that is not covered by the product guarantee.
The Mania SCX500 is supplied in DMX mode. If you are not using a DMX
controller, set the fixture to music trig or auto trig mode before use (see
Selecting operating modes on page 15).
Once the Mania SCX500 is correctly and safely installed, power on at the
fixtures power on/off switch. The fixture will reset.
If the Mania SCX500 resets and starts up successfully, three digits will
appear in the display for a few moments to indicate the software version
installed. The first digit is the major release number (i.e. the number
before the decimal point in a version number). For example, if software
version 1.1 is installed, the message 1 1 0 will appear in the display.
Any other message (see Error messages on page 21) indicates power
reset failure. If this occurs, switch off, wait a few seconds and switch on
again. If the software version number still fails to appear, consult your
Martin dealer.
The Mania SCX500 has three operating modes:
Music trig: In this mode, lighting effects are triggered by music intensity.
Auto trig: In this mode, lighting effects are triggered automatically.
Both music trig and auto trig modes can be used in:
Single fixture operation, where a Mania SCX500 operates
independently.
Master/slave operation, where one fixture sends signals to others via a
data link so that all fixtures perform an identical light show.
DMX mode: In this mode, fixtures can be controlled using a DMX
controller on the data link.
Fixtures need to be in DMX mode to operate as slaves in master/slave
operation.
Once the fixture has reset after powering on, if the fixture is in DMX mode
its DMX address will appear in the display. The Mania SCX500 is factoryset to DMX mode with the DMX address set to 001.
14
Mode selection
DMX Address
X100
X10
X1
Mode
Mode button
When a fixture is powered off and then on again, it will remember which
mode it is set to and start up in that mode.
Master/slave operation
In master/slave mode, one master Mania SCX500 sends trigger signals to
all the fixtures connected to it, and all fixtures run an identical dynamic
light show. Up to 32 Mania SCX500s can be connected together and
operated in master/slave mode. More fixtures can be added using an
optically isolated splitter/amplifier such as the Martin RS-485 Opto-Splitter
(P/N 90758060).
Important! Set only 1 fixture as master: damage can occur if 2 masters, or
a master and a controller, are linked together.
Slave mode
DMX Address
X100
X10
X1
Mode button
16
Operation
17
For individual control, each fixture must be assigned its own DMX address
and control channels. Fixtures with the same address will receive the
same instructions and behave identically.
If a fixture is set to 8-channel mode and you give it DMX address 100, for
example, it will use channels 100, 101, 102, 103, 104, 105, 106 and 107.
Channel 108 is available for the next fixture.
To set DMX addresses:
1. Power on the fixtures on the DMX link.
2. Depending on which channels are
available, decide on suitable DMX
addresses for the Mania SCX500s.
3. Enter the DMX address for each Mania
SCX500 using the three addressing
buttons on the control panel of each
fixture. The X1 button increases the last
digit in the DMX address, the X10 button
increases the address by 10 and the X100
increases the address by 100.
DMX Address
X100
X10
X1
Mode
Mo
DMX addressing
buttons
Reset
Strobe effect
Macros 1 - 12
Dimming (0 - 100% intensity)
Color wheel position and rotation
Gobo wheel position and rotation
Pan
Tilt
19
Data LED
lit
DMX Address
X100
X10
X1
Mode
Inverting pan
To set a Mania SCX500 to inverted pan:
1. Apply power to the fixture and wait for the fixture to reset.
2. Hold the Mode button pressed in. After 5 seconds the display will blink.
You are now in the control menu. Keeping the Mode button pressed in,
press the X100 button repeatedly, until 2 appears in the left of the
display.
If the display blinks 2 0 , the fixture is in normal pan mode.
If the display blinks 2 1 , the fixture is in inverted pan mode.
3. Keeping the Mode button pressed in, press the X1 button to toggle
between normal and inverted pan.
4. Release the Mode button to save the setting and return the fixture to
normal operation.
20
I nverti ng ti lt
To set a Mania SCX500 to inverted tilt:
1. Apply power to the fixture and wait for the fixture to reset.
2. Hold the Mode button pressed in. After 5 seconds the display will blink.
You are now in the control menu. Keeping the Mode button pressed in,
press the X100 button repeatedly, until 3 appears in the left of the
display.
If the display blinks 3 0 , the fixture is in normal tilt mode.
If the display blinks 3 1 , the fixture is in inverted tilt mode.
3. Keeping the Mode button pressed in, press the X1 button to toggle
between normal and inverted tilt.
4. Release the Mode button to save the setting and return the fixture to
normal operation.
Error messages
In the event of an internal error, the following messages will appear in the
digital display:
701
702
703
If an error message is displayed, try powering the fixture off and then on
again to reset it.
If the problem persists, contact your Martin dealer.
Operation
21
Lamp
The Mania SCX500 uses a 15V, 150W halogen lamp with integral reflector
(MR16).
Approved lamps
The Philips JCR/H5 (EFR/LL) 15 V, 150 W long-life halogen lamp,
average lamp life 500 hours, color temperature 3100 K, is approved for
use with the Mania SCX500.
Important! Use only an approved lamp. Installing any other lamp type may
damage the fixture.
Wear safety glasses and gloves and allow the fixture to cool
for at least 20 minutes before removing the lamp.
1. Disconnect the fixture from power and allow it to cool for at least 20
minutes.
22
2. Remove the lamp module cover release thumbscrew and open the
cover on its hinge. Do not confuse the cover release thumbscrew with
the focus adjustment knob.
Focus
adjustment knob
Lamp module
cover release
thumbscrew
23
Cleaning
Cleaning optical components
Use care when cleaning optical components. The coated surfaces are
fragile and small scratches may be visible in the fixtures light output.
1. Disconnect the fixture from AC power and allow it to cool for at least 20
minutes.
2. Remove the lamp module cover release thumbscrew and open the
lamp module cover on its hinge.
3. Blow or vacuum away loose dust. Remove residues from lenses and
filters with a soft cloth or cotton swabs wetted with isopropyl alcohol.
Regular glass cleaner may also be used, but no residues may remain.
4. Any streaking that remains can be removed by rinsing with distilled
water. Mixing the water with a small amount of wetting agent such as
Kodak Photoflo will help give a perfectly clear surface.
5. Dry with a clean, soft, lint-free cloth or blow dry with compressed air.
6. Replace the lamp module cover before reapplying power.
24
2. Pry open the fuse holder (located next to the power cable entry, EU
model illustrated) with a flat-head screwdriver and remove the fuse.
Fuse holder
3. Replace the fuse with one of the same type. The fuse rating is listed on
the serial number label and in Mania SCX 500 specifications on page
30.
4. Replace the fuse holder.
5. If fuses continue to blow, there is probably a fault. Disconnect the
fixture from power and data and contact a Martin service technician.
25
5. TROUBLESHOOTING
Problem
Probable cause(s)
No power to fixture.
Replace fuse.
Connect controller.
26
Remedy
6. DMX PROTOCOL
Channel
Value
Percent Function
0-4
5 - 68
69 - 100
101 - 112
113 - 124
125 - 136
137 - 148
149 - 160
161 - 172
173 - 184
185 - 196
197 - 208
209 - 220
221 - 232
233 - 249
250 - 255
0-1
2 - 26
27 - 39
40 - 44
45 - 48
49 - 53
54 - 58
59 - 62
63 - 67
68 - 72
73 - 76
77 - 81
82 - 86
87 - 91
92 - 97
98 - 100
0 - 255
0 - 100
Intensity
0 - 100%
DMX protocol
27
Channel
Value
0-5
6 - 11
12 - 17
18 - 23
24 - 29
30 - 35
36 - 41
42 - 47
48 - 53
54 - 59
60 - 65
66 - 71
72 - 77
78 - 83
84 - 89
90 - 95
96 - 101
102 - 107
108 - 113
114 - 119
120 - 125
126 - 131
132 - 137
138 - 143
144 - 149
150 - 155
156 - 161
162 - 167
168 - 173
174 - 179
180 - 185
186 - 191
192 - 197
198 - 203
204 - 229
230 - 255
28
Percent Function
Color wheel
Color 1 (White)
Split Color 1-2 (White and Blue B04)
Color 2 (Blue B04)
Split Color 2-3 (Blue B04 and Orange B09)
Color 3 (Orange B09)
Split Color 3-4 (Orange B09 and Red B01)
Color 4 (Red B01)
Split Color 4-5 (Red B01 and Light Yellow B03)
Color 5 (Light Yellow B03)
Split Color 5-6 (Light Yellow B03 and Pink B12)
Color 6 (Pink B12)
Split Color 6-7 (Pink B12 and Medium Blue B13)
Color 7 (Medium Blue B13)
Split Color 7-8 (Medium BlueB13 and Light Red B19)
Color 8 (Light Red B19)
Split Color 8-9 (Light Red B19 and Light Green B08)
Color 9 (Light Green B08)
Split Color 9-10 (Light Green B08 and Blue B05)
Color 10 (Blue B05)
Split Color 10-11 (Blue B05 and Pink B11)
Color 11 (Pink B11)
Split Color 11-12 (Pink B11 and Light Blue B06)
Color 12 (Light Blue B06)
Split Color 12-13 (Light Blue B06 and Yellow B02)
Color 13 (Yellow B02)
Split Color 13-14 (Yellow B02 and Primary Red B14)
Color 14 (Primary Red B14)
Split Color 14-15 (Primary Red B14 and Green B07)
Color 15 (Green B07)
Color 16 (Mix 1)
Color 17 (Mix 2)
Color 18 (Mix 3)
Color 19 (Mix 4)
Color 20 (Mix 5)
Continuous rotation
80 - 89 Clockwise rotation (fast to slow)
90 - 100 Counter-clockwise rotation (slow to fast)
0-1
2-3
4-6
7-8
9 - 11
12 - 13
14 - 15
16 - 18
19 - 20
21 - 22
23 - 25
26 - 27
28 - 29
30 - 32
33 - 34
35 - 37
38 - 39
40 - 41
42 -44
45 - 46
47 - 48
49 - 51
52 - 53
54 - 55
56 - 58
59 - 60
61 - 62
63 - 65
66 - 67
68 - 70
71 - 72
73 - 74
75 - 77
78 - 79
Channel
Value
0 - 11
12 - 23
24 - 35
36 - 47
48 - 59
60 - 71
72 - 83
84 - 95
96 - 107
108 - 119
120 - 131
132 - 143
144 - 155
156 - 167
168 - 179
180 - 191
192 - 223
224 - 255
Percent Function
Gobo wheel
Gobo 1 (Open)
Gobo 2 - Dune)
Gobo 3 - Sunburst
Gobo 4 - Gemini
Gobo 5 - Mr. Spok
Gobo 6 - Triptych
Gobo 7 - Space lice
Gobo 8 - Nova
Gobo 9 - Circular saw
Gobo 10 - Racer
Gobo 11 - Black hole
Gobo 12 - Bat
Gobo 13 - Beep
Gobo 14 - Fame
Gobo 15 - Thatch
Gobo 16 - Black out
Continuous rotation
75 - 87 Clockwise rotation (fast to slow)
88 - 100 Counter-clockwise rotation (slow to fast)
0-4
5-8
9 - 13
14 - 18
19 - 23
24 - 27
28 - 32
33 - 37
38 - 41
42 - 46
47 - 51
52 - 55
56 - 60
61 - 65
66 - 70
71 - 74
0 - 255
0 - 100
Pan
Left to right (127 = neutral)
0 - 255
0 - 100
Tilt
Down to up (127 = neutral)
0-1
2 - 79
0-1
2 - 100
7*
8*
0-2
3 - 255
0-2
3 - 255
* Channels 7 and 8 are available in 8-channel DMX mode only. In 6channel DMX mode, pan & tilt speed and color & gobo wheel rotation
speed are set to tracking.
Lamp
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V, 150 W, H5 MR16 halogen
Approved models . . . . . . . . . . . . . . . . . . . Philips JCR 15 V, 150 W H5 (EFR/LL)
Lamp base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GZ6.35
Dynamic effects
Full range continuous dimmer
Color wheel: 15 colors (including white), 5 multi-colors, split color function
Gobo wheel: 16 gobos
Moving mirror: 180 pan and 72 tilt
Electrical
AC power (US model) . . . . . . . . . . . . . . . . . . . . . . . 110-120 VAC nominal, 60 Hz
AC power (EU model) . . . . . . . . . . . . . . . . . . . . . . 220-240 VAC nominal, 50 Hz
Power and current US model*
@ 110 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 W, 1.27 A
@ 115 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W, 1.30 A
@ 120 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 W, 1.35 A
Power and current EU model*
@ 220 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 W, 0.66 A
@ 230 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 W, 0.66 A
@ 240 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 W, 0.68 A
*Figures are typical, not maximum. Allow for +/- 10% variation.
Fuse
Main fuse (US model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15 AT
Main fuse (EU model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AT
Connections
AC power inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-prong IEC male socket
Data in/out. . . . . . . . . 3-pin locking XLR, pin 1 shield, pin 2 cold (-), pin 3 hot (+)
Approvals
Optics
Beam angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Construction
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steel and aluminum
Installation
Minimum distance to combustible materials . . . . . . . . . . . . . . . . . . 0.1 m (4 in.)
Minimum distance to illuminated surfaces . . . . . . . . . . . . . . . . . . . . 1 m (3.3 ft.)
Minimum clearance around fan and air vents . . . . . . . . . . . . . . . . . 0.1 m (4 in.)
Thermal
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . .40 C (104 F)
Accessories
DMX termination plug (end of link), XLR male . . . . . . . . . . . . . . . .P/N 91613017
DMX termination plug, (start of link, master/slave), XLR female . .P/N 91613018
G-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 91602003
Half-coupler clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 91602005
5-pin male to 3-pin female XLR adaptor cable . . . . . . . . . . . . . . . P/N 11820005
5 meter (16.4 ft.) RS-485 XLR cable for data link . . . . . . . . . . . . . P/N 11820008
Ordering information
Mania SCX500 US model, 110-120 V, 60Hz . . . . . . . . . . . . . . . . .P/N 90430081
Mania SCX500 EU model, 220-240 V, 50Hz . . . . . . . . . . . . . . . . .P/N 90430080
Philips JCR/H5 15 V, 150 W (EFR/LL) lamp . . . . . . . . . . . . . . . . . P/N 97000110
3.15 AT main fuse (US model, 110-120 V) . . . . . . . . . . . . . . . . . .P/N 05020013
2 AT main fuse (EU model, 220-240 V) . . . . . . . . . . . . . . . . . . . . .P/N 05020009