Professional Documents
Culture Documents
Pcchips 789CG 30B PDF
Pcchips 789CG 30B PDF
Trademarks
IBM, VGA, and PS/2 are registered trademarks of International
Business Machines.
VIA is a registered trademark of VIA Technologies, Inc.
Microsoft, MS-DOS and Windows 98/ME/NT/2000/XP are
registered trademarks of Microsoft Corporation.
AMI is a registered trademark of American Megatrends Inc.
Other names used in this publication may be trademarks and are
acknowledged.
Copyright 2004
All Rights Reserved
M789CG Series, V3.0B
CLE266/November 2004
Table of Contents
Trademark ................................................................................... I
Static Electricity Precautions ............................................................ III
Pre-Installation Inspection ................................................................ III
Pre-Installation Inspection
1. Inspect this motherboard whether there are any damages to
components and connectors on the board.
2. If you suspect this motherboard has been damaged, do not
connect power to the system. Contact your motherboard
vendor about those damages.
iii
Notice:
1. Owing to Microsofts certifying schedule is various to every
supplier, we might have some drivers not certified yet by
Microsoft. Therefore, it might happen under Windows XP that
a dialogue box (shown as below) pop out warning you this
software has not passed Windows Logo testing to verify its
compatibility with Windows XP. Please rest assured that our
RD department has already tested and verified these drivers.
Just click the Continue Anyway button and go ahead the
installation.
vi
vii
Ausstattung
CPU-Typ
Untersttzt Onboard-VIA C3 CPU
Untersttzt 133 MHz Front-Side Bus
Chipsatz
Dieser Chipsatz besteht aus einer VIA CLE266 Northbridge und einer 8235
Southbridge. Die Chipsatzarchitektur ist in einem innovativen und skalierbaren
Design gehalten und verspricht sowohl Zuverlssigkeit als auch Leistungsstrke.
Unten stehend finden Sie eine Liste mit den Chipsatzteilen und deren jeweiligen
Funktionen:
Hochleistungs CPU-Schnittstelle: Untersttzt VIA C3-Prozessoren; 133/100/66
MHz CPU Front Side Bus (FSB)
8-Bit-Link Host Controller mit einer Bandbreite von 266MB/Sek untersttzt die
66MHz V-Link Host-Schnittstelle mit der totalen Bandbreite von 266MB/Sek.
Fortgeschrittener Hochleistungs-DDR/SDR DRAM Controller untersttzt gleichzeitige DRAM-Schnittstelle mit Host-CPU (133/100 MHz) fr beste flexible
Einstellung; Untersttzt 4 Speicherbnke fr bis zu 2 GB DRAM
Integrierte Grafikfunktion / Videobeschleuniger : 16/32/64 Framebuffer
verwendet Systemspeicher; interne AGP 4x-Funktionalitt.
Mitwirkender PCI-Bus-Controller: 33 MHz-Betrieb, nach den Richtlinien von
PCI 2.2, 32 Bit 3.3V PCI-Schnittstelle mit einer Eingangsenergie-Toleranz von
5V.
Fast Ethernet Controller: Voller und halber Duplex-Betrieb von 1/10/100
MHz
UltraDMA-133/100/66/33 Master-Modus EIDE-Controller: bertragungsrate
von bis zu 133MB/Sek um die Driver des PIO-Modus 4, Multi-Word-DMA-Modus 2, und eine UltraDMA-133-Schnittstelle zu decken.
Direct Sound Ready (Direkter Fertigton) AC97 Digital Audio Controller: nach
den Richtlinien von AC97 2.1
Universaler Serien-Bus-Controller: USB v2.0 und vergrsserte Host-Controller-Schnittstelle (EHCI) kompatibel mit v1.0; USB v1.1 und Universale HostController-Schnittstelle (UHCI) kompatibel mit v1.1
Speicheruntersttzung
Zwei DIMM Steckpltze fr DDR Speichermodule
Untersttzt DDR266/200 Speicherbus
Maximal auf 2GB Speicher erweiterbar
Erweiterungssteckpltze
Ein CNR-Steckplatz
Zwei 32-Bit PCI-Steckpltze fr PCI 2.2-kompatibles Businterface
viii
ix
Caratteristiche
Tipo CPU
Supporta la CPU VIA C3 installata
Supporta Front Side Bus (FSB) di 133 MHz
Chipset
In accordo ad una archittettura scabile e innovative sono presenti nel chipset il
Northbridge VIA CLE266 e Southbridge 8235. Segue una lista con i chipset e le
rispettive funzioni:
Interfaccia CPU di elevata performance: Supporta processori VIA C3 e CPU
FSB (Front Side Bus) di133/100/66 MHz
Controller Host Link 8bit ad alta velocit (266MB) in grado di supportare
interfacce Link Host a 66 MHz
Controller DRAM DDR/SDR ad alte prestazioni in grado di supportare le
DRAM sincrone con CPU host (133/100 MHz) per una maggiore flessibilit
nella configurazione; Supporta 4 banchi sino a 2GB di DRAM
Grafica integrata/acceleratore video: buffer di frame da 16/32/64 che sfrutta la
memoria di sistema; prestazione Internal AGP 4x
Programma di controllo PCI Bus: operativit 33 MHz , compatibile PCI 2.2,
interfaccia 32 bit 3.3V PCI con immissione dati tollerante V5
Programma di controllo veloce Ethernet: 1/10/100 MHz operativit piena o
mezzo duplex
Programma EIDE di controllo UltraDMA-133/100/66/33 Master Mode EIDE:
Velocit di trasferimento fino a 133MB/sec che copre PIO mode 4, drive multiparola modalit DMA e interfaccia UltraDMA-133
Programma di controllo audio digitale per suono diretto AC97: AC97 2.1
compatibile
Programma di controllo per Bus universali seriali: USB v2.0 ed interfaccia
Host Controller migliorata (EHCI) v1.0 compatibile; USB v1.1 e interfaccia
universale Host Controller (UHCI) v1.1 compatibile
Supporto Memoria
Slot di espansione
Una slot CNR
Due slot PCI a 32 bit per interfaccia bus PCI 2.2
xi
xii
xiii
Chipset
Hay VIA CLE266 Northbridge y 8235 Southbridge en este chipset en confomidad con una arquitectura innovadora y escalable con fiabilidad y rendimiento
comprobados. He aqu una lista del arreglo del chipset y sus respectivas caractersticas:
Interfaz de CPU de alto rendimiento: Soporte para los procesadores de VIA
C3; Bus de Lado Frontal (FSB) de CPU en 133/100/66 MHz
Controlador Anfitrin V-Link de 8-bit de ancho de banda de 266MB/seg
soporta la interfaz de Anfitrin V-Link de 66MHz con el ancho de banda total
de 266MB/seg
Controlador DDR/SDR DRAM de alto rendimiento avanzado soporta
la interfaz DRAM sincrnica con CPU anfitriona (133/100 MHz) para la
configuracin ms flexible; Soporta 4 bancos hasta DRAMs de 2 GB
Acelerador de Grficas/Vdeo Integrado : buffer de marco 16/32/64 que usa la
memoria de sistema; rendimiento de AGP 4x interno
Controlador de Bus PCI concurrente: operacin de 33 MHz, conformidad PCI
2.2, interfaz 32 bit 3.3V PCI con entradas tolerantes de 5V
Controlador Fast Ethernet: operacin duplex completo y medio de 1/10/100
MHz
Controlador EIDE de Modo Mster UltraDMA-133/100/66/33: ndice de
transferencia hasta 133MB/seg para cubrir el PIO modo 4, unidades de multiword DMA modo 2, e interfaz UltraDMA-133
Sonido Directo Listo Controlador de Sonido Digital AC97: Conformidad AC97
2.1
Controlador de Bus Serial Universal: USB v2.0 y compatible con la Interfaz
de Controlador Anfitrin Reforzado (EHCI) v1.0; USB v1.1 y compatible con la
Interfaz de Controlador Anfitrin Universal (UHCI) v1.1
Soporte de Memoria
Dos ranuras DIMM para mdulos de memoria DDR
Soporta bus de memoria en DDR266/200
Memoria mxima instalada es 2GB
Ranuras de Expansin
Una ranura CNR
Dos ranuras 32-bit PCI para la interfaz de bus conforme con PCI 2.2
xiv
xv
xvi
xvii
xviii
xix
IDE
CD
CPU
VIA C3 CPU
133 MHz
2 DDR DIMM
DDR266/200
2GB
1 CNR
2 32 PCI PCI 2.2
xx
CD
S/PDIF 96 / 48 kHz24 / 20 / 16
PC 3D OK
I/O
I/O
2 PS/2
1
1
1 VGA
1 LAN ()
4 USB2.0
LAN ()
10Base-T/100Base-TX
-100/10 Mbps
/ & MII
10/100/
IEEE 802.310Base-T 100Base-Tx
USB2.0
2.0
Intel 1.0
1.1
PCI 2 / UHCI 1
EHCI
Root 4 UHCI EHCI
1.1 PCI
xxi
xxii
Chapter 1 Introduction
This motherboard has a VIA C3 CPU onboard with front-side
bus speed up to 133MHz.
This motherboard integrates the VIA CLE266 Northbridge and
8235 Southbridge chipsets that support DDR 266MHz, Ultra
DMA 33/66/100/133 function and remarkably high system
performance under all types of system operations
It supports built-in USB 2.0 providing higher bandwidth. It
implements Universal Serial Bus Specification Revision 2.0
and is compliant with UHCI 1.1 and EHCI 1.0.
The motherboard supports the built-in AC97 Codec, two 32-bit
PCI slots, one CNR (Communications and Networking Riser)
slot, and an onboard 10BaseT/100BaseTX Network interface
(optional). This motherboard integrates a 128-bit 3D/2D
graphics engine and a high-performance 3D accelerator.
In addition, this motherboard has a full set of I/O ports including
two PS/2 ports for mouse and keyboard, one serial port, one VGA
port, one parallel port. one LAN port (optional), audio jacks for
microphone, line-in and line-out, four back-panel USB2.0 ports
and onboard USB header USB1 providing two extra ports by
connecting the extended USB module to the motherboard.
This motherboard has all the features you need to develop a
powerful multimedia workstation. The board is FLEX ATX size
and has a power connector for an ATX power supply.
Key Features
The key features of this motherboard include:
CPU Type
Supports the VIA C3 CPU onboard
Supports 133 MHz Front-Side Bus
Chipset
There are VIA CLE266 Northbridge and 8235 Southbridge
in this chipset in accordance with an innovative and scalable
architecture with proven reliability and performance. A few of the
chipsets advanced features are:
High Performance CPU Interface: Support for VIA C3
processors; 133/100/66 MHz CPU Front Side Bus (FSB)
High Bandwith 266 MB/sec 8-Bit V-Link Host Controller:
Supports 66 MHz V-Link Host Interface with total bandwidth of 266 MB/sec
Advanced High-Performance DDR/SDR DRAM Controller: DRAM interface synchronous with host CPU (133/100
MHz) for most flexible configuration; Supports 4 banks up
to 2 GB DRAMs
Integrated Graphics / Video Accelerator : 16/32/64 frame
buffer using system memory; Internal AGP 4x performance
Concurrent PCI Bus Controller: 33 MHz operation, PCI 2.2
compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs
Fast Ethernet Controller: 1/10/100 MHz full and half
duplex operation
UltraDMA-133/100/66/33 Master Mode EIDE Controller:
Transfer rate up to 133MB/sec to cover PIO mode 4, multiword DMA mode 2 drives, and UltraDMA-133 interface
Direct Sound Ready AC97 Digital Audio Controller:
AC97 2.1 compliant
Chapter 1: Introduction
ties.
Stereo Line-in function shared with Surround out.
High quality pseudo-differential analog CD Audio input.
S/PDIF Output support: Output 96 / 48 kHz with 24 / 20 /16
bits
Valuable add-on software technology: Support most industry
standards of PC 3D sound and unique karaoke function
support featured with microphone echo, key shifting, and
vocal cancellation.
USB 2.0
Compliant with Universal Serial Bus Specification Revision
2.0
Compliant with Intels Enhanced Host Controller Interface
Specification Revision 1.0
4
Chapter 1: Introduction
Power management
CPU parameters and memory timing
Hardware monitoring parameters
The firmware can also be used to set parameters for different
processor clock speeds.
Dimensions
FLEX ATX form factor (230 x 170 mm)
Note: Hardware specifications and software items are subject to
change without notification.
Package Contents
Your motherboard package ships with the following items:
The motherboard
The User Guide
One diskette drive ribbon cable (optional)
One IDE drive ribbon cable
The Software support CD
Optional Accessories
You can purchase the following optional accessories for this
mainboard.
The Extended USB module
The CNR v.90 56K Fax/Modem card
Card Reader (You can buy your own Card Reader from the
third party, but please contact your local Card Reader
vendor on any issues of the specification and compatibility.
Note: You can purchase your own optional accessories from the
third party, but please contact your local vendor on any issues
of the specification and compatibility.
Motherboard Components
CPU_FAN1
DIMM
IDE1
IO
PORTS
J5
USB1
IDE2
ATX1
AUDIO2
CD1
PCI
SPK1
JBAT1
FDC1
CNR1
LABEL
DIMM1/2
IDE1/2
ATX1
USB1
FDC1
PANEL1
SYSTEM_FAN1
JBAT1
SPK1
PCI 1-2
CD1
SYSTEM_FAN1
PANEL1
COMPONENTS
Two 184-pin DDR SDRAM sockets
Primary/Secondary IDE connectors
Standard 20-Pin ATX Power connector
Front Panel USB header
Floppy Disk Drive connector
Front Panel Switch/LED header
System Fan connector
Clear CMOS jumper
Speaker header
32-bit PCI slots
Analog Audio Input header
LABEL
AUDIO2
J5
CPU_FAN1
CNR1
COMPONENTS
Front Panel Audio header
USB Card Reader header
CPU Fan connector
Communications Networking Riser slot
I/O Ports
The illustration below shows a side view of the built-in I/O ports
on the motherboard.
Shared
with J5
PS/2 Mouse
(Optional)
DIMM1
DIMM2
10
2.
3.
4.
11
Jumper Settings
Connecting two pins with a jumper cap is SHORT; removing a
jumper cap from these pins, OPEN.
1
JBAT1
12
ATX1
PANEL1
SYSTEM_FAN1
13
1
J5
USB1
1
AUDIO2
SPK1
14
1.
2.
3.
Signal
VERG_FP_USBPWR0
USB_FP_P0(-)
USB_FP_P0(+)
GROUND
KEY
Pin
2
4
6
8
10
Signal
VERG_FP_USBPWR0
USB_FP_P1(-)
USB_FP_P1(+)
GROUND
USB_FP_OC0
15
Note2: Please check the pin assignment of the cable and the
USB connector on the motherboard. Make sure the pin
assignment will match before plugging in. Any incorrect usage
may cause unexpected damage to the system. The vendor
wont be responsible for any incidental or consequential
damage arising from the usage or misusage of the purchased
product.
16
IDE1
IDE2
1
FDC1
17
The motherboard ships with an IDE cable that can support one or
two IDE devices. If you connect two devices to a single cable,
you must configure one of the drives as Master and one of the
drives as Slave. The documentation of the IDE device will tell you
how to configure the device as a Master or Slave device. The
Master device connects to the end of the cable.
Install the device(s) and connect power from the system power
supply. Use the cable provided to connect the device(s) to the
Primary IDE channel connector IDE1 on the motherboard.
If you want to install more IDE devices, you can purchase a
second IDE cable and connect one or two devices to the Secondary IDE channel connector IDE2 on the mainboard. If you have
two devices on the cable, one must be Master and one must be
Slave.
Analog Audio Input Header
If you have installed a CD-ROM drive or DVD-ROM drive, you
can connect the drive audio cable to the onboard sound system.
1
CD1
18
When you first start up your system, the BIOS should automatically detect your CD-ROM/DVD drive. If it doesnt, enter the
Setup Utility and configure the CD-ROM/DVD drive that you
have installed. On the motherboard, locate the 4-pin header CD1.
Pin
1
2
3
4
Signal
CD IN L
GND
GND
CD IN R
Expansion Slots
This motherboard has one CNR and two 32-bit PCI slots.
PCI1
PCI2
CNR1
19
3.
4.
CNR Slot
You can install the CNR (Communications and Networking Riser)
cards in this slot, including LAN, Modem, and Audio functions.
PCI Slots
You can install the 32-bit PCI interface expansion cards in the
slots.
20
21
Features Setup
CPU PnP Setup
Hardware Monitor
Load Optimal Defaults
Change Password
Exit
ESC: Quit
: Select Item <Shift>F2:Chabge Color
F6: Optimal Values
F7: Best Performance Values
Standards CMOS setup for changing time, date, hard disk type, etc.
32Bit
Mode
On
On
On
On
ESC : Exit
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
F3 : Detect All HDD
23
Quick Boot
If you enable this item, the system starts up more quickly be
elimination some of the power on test routines.
1st Boot Device/2 nd Boot Device/3 rd Boot Device
Use these items to determine the device order the computer
uses to look for an operating system to load at start-up time.
Try Other Boot Device
If you enable this item, the system will also search for other
boot devices if it fails to find an operating system from the first
two locations.
24
25
26
27
LAN/Ring Power On
The system can be turned off with a software command. If you
enable this item, the system can automatically resume if there is
an incoming call on the Modem/Ring, or traffic on the network
adapter. You must use an ATX power supply in order to use this
feature.
Keyboard Power On
If you enable this item, system can automatically resume by
pressing any keys, hot or typing in the password. You must use an
ATX power supply in order to use this feature.
PowerOn by RTC Alarm / Date / Hour / Minute / Second
The system can be turned off with a software command. If you
enable this item, the system can automatically resume at a fixed
time based on the systems RTC (realtime clock). Use the items
below this one to set the date and time of the wake-up alarm. You
must use an ATX power supply in order to use this feature.
28
Yes
32MB
PCI
Yes
Disabled
ESC:Quit
:Select Item
F1:Help
PU/PD/+/-:Modify
F5:Old Values (Shift)F2:Color
F6:Load BIOS Defaults
F7:Load Setup Defaults
29
30
OnBoard FDC
Use this item to enable or disable the onboard floppy disk drive
interface.
OnBoard Serial PortA
Use this item to enable or disable the onboard COM1 serial port,
and to assign a port address.
Onboard Parallel Port
This item enables or disables the onboard LPT1 parallel port,
and assigns a port address. The Auto setting will detect and
available address.
Parallel Port Mode
Use this item to set the parallel port mode. You can select SPP
(Standard Parallel Port), ECP (Extended Capabilities Port), EPP
(Enhanced Parallel Port), or ECP + EPP.
Parallel Port IRQ
Use this item to assign IRQ to the parallel port.
Parallel Port DMA
Use this item to assign a DMA channel to the parallel port.
OnBoard IDE
This item enables or disables either or both of the onboard
Primary and Secondary IDE channels.
Onboard LAN
This item enables or disables the onboard Ethernet LAN.
Audio Device
This item enables or disables the AC 97 audio chip.
Modem Device
This item enables or disables the MC 97 modem chip.Ethernet
Device
31
USB Controller
Enable this item to select the USB ports or disable.
USB Function for DOS
Enable this item if you plan to use the USB ports on this
motherboard in a DOS environment.
ThumbDrive Support for DOS
Enable this item to make a small portion of memory storage
device for the USB ports.
Auto
ESC:Quit
:Select Item
F1:Help
PU/PD/+/-:Modify
F5:Old Values
(Shift)F2:Color
F6:Load BIOS Defaults
F7:Load Setup Defaults
DDR Frequency
This item adjusts the SDRAM frequency installed in your
system.
32
ESC:Quit
:Select Item
F1:Help
PU/PD/+/-:Modify
F5:Old Values
(Shift)F2:Color
F6:Load BIOS Defaults
F7:Load Setup Defaults
33
Change Password
If you highlight this item and press Enter, a dialog box appears that
you can enter a Supervisor password. You can enter no more than
six letters or numbers. Press Enter after you have typed in the
password. There will be the second dialog box asking you to
retype the password for confirmation. Press Enter after you have
retyped it correctly. Then, the password is required for the access
to the Setup Utility or for it at start-up, depending on the setting of
the Password Check item in Advanced Setup.
Exit
Highlight this item and press Enter to save the changes that you
have made in the Setup Utility configuration and exit the program.
When the Save and Exit dialog box appears, press Y to save and
exit, or press N to exit without saving.
34
35
Once any of the installation procedures start, software is automatically installed in sequence. You need to follow the onscreen
instructions, confirm commands and allow the computer to restart
as few times as needed to complete installing whatever software
you selected. When the process is finished, all the support software will be installed and start working.
37
38