Professional Documents
Culture Documents
Continuously Hot-Dip Coated Steel Sheet and Strip - Tolerances On Dimensions and Shape
Continuously Hot-Dip Coated Steel Sheet and Strip - Tolerances On Dimensions and Shape
it
info@gruppocommit.it
PROFESSIONISTI DI PERFEZIONE
EUROPEAN STANDARD
NORME EUROPENNE
EUROPISCHE NORM
EN 10143
Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
Tolerances closer than special tolerances may be agreed at the time of enquiry and order.
In the case of products for which no yield strength is specified, the tolerances specified in Table
2 for the grades DX51D and S550GD and in table 4 for all other grades apply, unless otherwise
agreed at the time of enquiry and order.
Table 1 - Tolerances for steel grades with specified minimum yield strength Re or specified minimum
proof strength Rp0,2 < 260 MPa
Nominal thickness t
0,20 < t < 0,40
0,40 < t < 0,60
0,60 < t < 0,80
0,80 < t < 1,00
1,00 < t < 1,20
1,20 < t < 1,60
1,60 < t < 2,00
2,00 < t < 2,50
2,50 < t < 3,00
3,00 < t < 5,00
5,00 < t < 6,50
Normal tolerances a
for a nominal width w
> 1500
+ 0,06
+ 0,06
+ 0,07
+ 0,08
+ 0,09
+ 0,12
+ 0,14
+ 0,16
+ 0,18
+ 0,21
+ 0,23
dimensions in mm
a) The thickness tolerances in the region of coil welds may be increased by a maximum of 50% over a lenght of
10 m. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of enquiry an order,
to normal and special (negative and positive) tolerances. For thicker coatings, see 6.2
b) Wide strip: width 600 mm; slit wide strip: rolling width 600 mm, slit to width less than 600 mm.
1/2
www.gruppocommit.it
Table 2 - Tolerances for steel grades with specified minimum proof strength
260 MPa Rp0,2 < 360 MPa and for grades DX51D and S550GD
Nominal thickness t
0,20 < t < 0,40
0,40 < t < 0,60
0,60 < t < 0,80
0,80 < t < 1,00
1,00 < t < 1,20
1,20 < t < 1,60
1,60 < t < 2,00
2,00 < t < 2,50
2,50 < t < 3,00
3,00 < t < 5,00
5,00 < t < 6,50
Normal tolerances a
for a nominal width w
< 1200 b 1200 < w < 1500 > 1500
+ 0,05
+ 0,06
+ 0,07
+ 0,05
+ 0,06
+ 0,07
+ 0,06
+ 0,07
+ 0,08
+ 0,07
+ 0,08
+ 0,09
+ 0,08
+ 0,09
+ 0,11
+ 0,11
+0,13
+ 0,14
+ 0,14
+ 0,15
+ 0,16
+ 0,16
+ 0,17
+ 0,18
+ 0,19
+ 0,20
+ 0,20
+ 0,22
+ 0,24
+ 0,25
+ 0,24
+ 0,25
+ 0,26
dimensions in mm
a) The thickness tolerances in the region of coil welds may be increased by a maximum of 50% over a lenght of
10 m. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of enquiry an order, to
normal and special (negative and positive) tolerances. For thicker coatings, see 6.2
b) Wide strip: width 600 mm; slit wide strip: rolling width 600 mm, slit to width less than 600 mm.
Nominal width w
600 < w < 1200
1200 < w < 1500
1500 < w < 1800
w > 1800
Normal
tolerances
+5
0
+6
0
+7
0
+8
0
Special
tolerances (S)
+2
0
+2
0
+3
0
+3
0
2/2