Professional Documents
Culture Documents
93ZJ Secc 8L Lamps
93ZJ Secc 8L Lamps
LAMPS
CONTENTS
page page
GENERAL INFORMATION
Each vehicle is equipped with various lamp assem- brush. Coat the inside of the socket lightly with Mo-
blies. A good ground is necessary for proper lighting part Multi-Purpose Grease or equivalent.
operation. Grounding is provided by the lamp socket Aero headlamps use a replaceable bulb that is
when it comes in contact with the metal body, or mounted in a molded plastic lens.
through a separate ground wire.
When changing lamp bulbs check the socket for
corrosion. If corrosion is present, clean it with a wire
DIAGNOSTIC PROCEDURES
Always begin any diagnosis by testing all of the DIMMER SWITCH TEST
fuses and circuit breakers in the system. Refer to (1) Disconnect battery negative cable.
Group 8W, Wiring Diagrams. (2) Remove tilt lever.
(3) Remove screws along bottom edge of steering
LEFT HAND SWITCH POD column.
The multi-function switch pod contains electrical (4) Remove upper and lower shrouds to gain access
circuitry for: to the switch connector (Fig. 1).
• Auto Headlamps
• Park Lamps
• Headlamps
• Low Beam/Fog Lamp
• Instrument Lamp Intensity
• Dome Lamp
This multi-function switch pod is mounted to the
left hand side of the instrument panel. Should any
function of the switch fail, other than illumination
bulbs, the entire switch pod must be replaced.
The multi-function switch also serves as a fog lamp
lock-out circuit. The circuit to the fog lamp switch is
completed only when the dimmer switch is in the low
beam position.
(5) Remove switch connector (Figs. 2 and 3). (6) Use an ohmmeter to test for continuity between
the terminals of the switch as shown in the chart
(Fig. 4).
(7) Refer to Service Procedures for assembly.
SERVICE PROCEDURES
INDEX
page page
HEADLAMP ALIGNMENT (7) Measure distance from the centerline of the ve-
Headlamps can be aligned using the screen method hicle to the center of each headlamp being aligned.
provided in this section. Alignment Tool C4466-A or Transfer measurements to screen (with tape) to each
equivalent can also be used. Refer to instructions side of vehicle centerline. Use these lines for left/right
provided with the tool for proper procedures. The adjustment reference.
preferred headlamp alignment setting is 0 for
the left/right adjustment and 1( down for the HEADLAMP ADJUSTMENT
up/down adjustment. A properly aimed low beam will project the top edge
of high intensity pattern on the screen from 50 mm (2
HEADLAMP ALIGNMENT PREPARATION in.) above to 50 mm (2 in.) below headlamp center-
(1) Verify headlamp dimmer switch and high beam line. The side-to-side left edge of high intensity pat-
indicator operation. tern should be from 50 mm (2 in.) left to 50 mm (2 in.)
(2) Correct defective components that could hinder right of headlamp centerline (Fig. 1). The preferred
proper headlamp alignment. headlamp alignment is 0 for the left/right ad-
(3) Verify proper tire inflation. justment and 1( down for the up/down adjust-
(4) Clean headlamp lenses. ment. The high beams on a vehicle with aero head-
(5) Verify that luggage area is not heavily loaded. lamps cannot be aligned. The high beam pattern
(6) Fuel tank should be FULL. Add 2.94 kg (6.5 should be correct when the low beams are aligned
lbs.) of weight over the fuel tank for each estimated properly.
gallon of missing fuel. To adjust headlamp aim, rotate alignment screws.
INSTALLATION
(1) Install a bulb in lamp socket. Fig. 11 Center High Mounted Stop Lamp
(2) Position license plate lamp visor on liftgate and
install screws (Fig 10).
UNDERHOOD LAMP
When equipped, the underhood lamp is installed on
the hood right, rear panel. The lamp is on when hood
is opened by way of liquid ON/OFF switch that is
integral with lamp base (Fig. 13).
BULB REMOVAL
(1) Disconnect wire harness connector from under-
hood lamp (Fig. 12).
(2) Rotate bulb counterclockwise. Remove it from
lamp base socket.
BULB INSTALLATION
(1) Insert replacement bulb in lamp base socket.
Rotate it clockwise.
(2) Connect wire harness connector to lamp.
HOUSING REMOVAL
(1) Disconnect wire harness connector from lamp.
(2) Rotate bulb counterclockwise. Remove it from
lamp base socket.
(3) Remove screw that attaches lamp reflector
bracket to hood inner panel (Fig. 12). Fig. 12 Underhood Lamp
(4) Remove lamp from hood inner panel.
HOUSING INSTALLATION
(1) Position underhood lamp on the hood inner
panel.
(2) Install screw through lamp and into the hood
panel.
(3) Insert bulb in lamp base socket and rotate it
clockwise.
(4) Connect wire harness connector to lamp.
INTERIOR LAMPS
INDEX
page page
DOME/COURTESY LAMP SERVICE INFORMATION is located at each side of the vanity mirror. The lamps
The interior lamp bulbs illuminate when they are are switched ON automatically when the mirror cover
connected to vehicle body ground. By way of appli- is lifted (Fig. 1).
cable switch:
• Dome lamp switch
• Glove box switch
• Door pillar switch
• Liftgate switch (if the cargo lamp is ON.)
If equipped with Security Alarm Module, refer to
Group 8Q—Vehicle Theft Security System.
should indicate approximately zero ohms. If not, re- (2) Rotate the screwdriver until lens snaps out of
pair the open circuit in the wire harness to vehicle the housing.
body ground. (3) Remove lens from housing.
(4) Remove bulb from terminals.
DOME/READING LAMP
INSTALLATION
REMOVAL (1) Insert bulb into reding lamp terminals.
(1) Insert a flat blade screwdriver in slot at the (2) Replace lens by holding lens level and pushing
center of the lamp housing. Rotate screwdriver up-
rearward into housing.
ward and unsnap dome lamp lens.
(3) Push lens up to snap into housing.
(2) Pull lens downward. Remove it from lamp hous-
ing.
CARGO LAMP/BULB
(3) Remove the lamp housing retaining screws (Fig. The cargo lamp bulb housing is integral with the
2). upper rear headliner trim moulding. To replace bulb
(4) Push housing forward and release housing from housing the trim moulding must be replaced.
bracket.
REMOVAL
(1) Insert a flat blade screwdriver in slots provided
at lower portion of lens.
(2) Rotate screwdriver upward until lens snaps out
of housing.
(3) Remove lens from housing (Fig. 3).
(4) Remove bulb from bulb holder.
INSTALLATION
(1) Position dome/reading lamp housing at head-
liner cavity.
(2) Connect wire harness connectors. Fig. 3 Cargo Lamp
(3) Locate rear pods of the lamp in the slots of the INSTALLATION
dome lamp bracket. Push lamp housing up and to (1) Install bulb in holder.
rear. (2) Insert upper tabs of lens into lens housing.
(4) Install the lamp housing screws (Fig. 2). (3) Snap lower portion of lens into slots at lens
(5) Position dome lamp lens at lamp housing. Snap housing (Fig. 3).
lens into housing.
DOOR COURTESY LAMP
DOME LAMP BULB
REMOVAL
REMOVAL (1) Remove door panel. Refer to Group 23—Body
(1) Insert a flat blade screwdriver in slot at front of Components for service procedure.
lens. (2) Disconnect wiring harness connector (Fig. 4).
Z LAMPS 8L - 11
OVERHEAD CONSOLE
To remove or repair overhead console refer to Group
8C, Overhead Console.
8L - 12 LAMPS Z
INDEX
page page
DAYTIME RUNNING LIGHT MODULE To find an intermittent fault, check the mating
The headlamps on vehicles sold in Canada, will go terminals at each component and connector for a poor
ON when the ignition is turned ON. The module must connection. Also check that each terminal of mating
also receive a movement signal from distance sensor. connectors is properly seated. If the connections ap-
This provides a constant Lights On condition while pear to be reliable, try the System Check again while
the vehicle is rolling. The lamps illuminate at less moving the wire harness from side to side at each
than 50% of normal intensity. component. Once a fault has been corrected, perform
The Daytime Running Light Module is located on the System Check to verify the diagnosis.
right inner fender below power distribution center.
AUTO HEADLAMP MODULE
(1) Remove bolts holding module and bracket to
The module receives inputs from the auto headlamp
vehicle (Fig. 1).
switch and auto headlamp sensor. Based on these
(2) Disconnect electrical connector.
inputs the module will control the lamps. The auto
To install module, reverse the removal procedures.
headlamp module is located behind the glove box to
the right of the security alarm module.
REMOVAL
(1) Disconnect battery negative cable.
(2) Remove two screws holding top of center cluster
bezel (Fig. 2).
REMOVAL
(1) Remove battery negative cable.
(2) Remove spare tire from carrier.
(3) Remove access door (Fig. 11).
(4) Remove wiring connectors at top of module.
(5) Remove 1 screw holding module to inner quar-
ter panel.
(6) Remove lamp outage module.
For installation, reverse the removal procedure.
BULB APPLICATION
INTERIOR LAMPS
Service procedures for most of the lamps in the
instrument panel, are located in Group 8E. Some