Professional Documents
Culture Documents
2708201620160827213459مشروع دعوة عطاء جهاز فحص عدادات كهرباء
2708201620160827213459مشروع دعوة عطاء جهاز فحص عدادات كهرباء
for continuous
33KV
36KV
3
50
3
1500
Resistance
Horizontal
All low voltage equipment must be capable of operating within a range of (+10% to
15%) of the rated voltage Tripping devices shall be capable of operating within the
range (+10% to 25%) of the rated voltage.
4- SITE CONDITIONS
The Plant and materials supplied shall be designed for continuous service in Jordan,
including, where appropriate, storage in the open air and use and operation in the
prevailing weather conditions at site which as follows:Altitude
-400 m to 1360 m
Highest ambient air temperature
50 Deg. C
Lowest ambient air temperature
-5 Deg. C
Average relative humidity
40 - 90%
Annual average rainfall approx.
30 cms
Annual average thunderstorm days
16
The area is almost desert in most places with occasional sand storms
5- FUNDAMENTALS FOR THE DESIGN
In compliance with the requirements of the Specification, both with respect to
arrangement and detail, design is to conform to the best current engineering practice
the Plant and materials are to be of the manufacturers standard design provided
that this design is in general accordance with the Specification.
The essence of design should be simplicity and reliability in order to give long
continuous service with high economy and low maintains cost. The design,
dimensions and materials of all parts are to be such that they will not suffer damage as
a result of stresses under the most service conditions.
Fully detailed specification of the Plant and materials are to be submitted describing
particularly the materials to be used. The materials used in the manufacture of the
items supplied are to be of the highest quality and selected particularly to meet the
duties required of them.
Workmanship and general finish are to be of the highest class throughout, and all similar
parts are to be interchangeable.
All plant and materials are to operate without undue vibration and with the least
possible amount of noise.
All plant and materials are to be designed to minimize the risk of fire and any damage
which may be caused in the event of fire.
In the design and manufacture of the plant and materials metric units of
measurement shall be used throughout.
6- STANDARDS
Unless another Standard is specifically mentioned in this Specification all Plant and
materials provided under the Contract shall preferably be in Accordance with IEC
or ISO Recommendations. Where no such Recommendations exist then the plant and
materials shall be in accordance with such other authoritative Standards
appropriate to the country of manufacture as in the opinion of the Engineer ensures
an equivalent or higher quality The Recommendations or Standard used shall be those
4
Technical Specifications
And Schedules
Technical Specifications
Of
Meter Test Bench
TECHNICAL SPECIFICATIONS
METER TEST BENCH
Meter test bench shall have the following technical specifications and features:
1.
2.
3.
4.
5.
6.
7.
8.
9.
The Meter test bench shall be able to test 10 Single phase or three phase
electromechanical or electronic meters at a time.
The meter test bench shall be able to test the single and three phase meters with
closed link at a time.
The test station is suitable for adjustment and testing of class0.1, 0.2, 0.5, 1.0 and
2.0 electricity meters.
Two rack with capacity of 20 meters (L- shape, 10 meters in each rack).
The meter rack shall be equipped with quick connector for each meter, mounted
on transverse rails of adjustable height; all the auxiliary circuit connectors for
meter control can be integrated with these quick connector blocks.
The quick connecters, current leads and cables should carry the maximum rated
current 120A for Continuous operation.
It shall be suitable for single phase active / reactive meters, three phase three wire and
four wire active / reactive / apparent meters.
Meter test bench shall be fully automatic.
Meter test bench shall perform the following tests:
Starting current test.
Accuracy test.
Creep test.
Register test (dial test).
Tariff register test.
Maximum demand test.
Meter test bench shall be provided with 20 photoelectric scanners for bothn
electromechanical and static meters.
11. Meter test bench shall be provided with two warning light ( one for each rack),
with red light if the meter test bench is in test mode, and green light if the meter test
bench is ready for test.
12. Meter test bench shall be provided with four emergency stop (two for each rack).
13. The Reference standard should be reach the following accuracy:
Voltage: class 0.05% for amplitude, class 0.05o for angle.
Current: class 0.05% for amplitude, class 0.01o for angle.
Power and Energy: class 0.02% at power factor =1. And class 0.04% at
power factor =0.5.
10.
14.
15.
Having precision class C.T.'s and V.T's not less than 0.1.
The C.T.'s shall be suitable for current ranges from 0.01 to 120 Amperes, with 5%
step.
9
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
The V.T.'s shall be suitable for voltage ranges from 10 to 500 volts phase to neutral,
with 10% step.
Phase angle range from 0 to 360, with resolution 0.05 or better.
The bench shall comprise suitable ammeters, voltmeter, and power factor meters
for each phase with accuracy class 0.2.
The power output should not be less than 500 VA per phase for the current circuit and
400 VA per phase for voltage circuit with protection against short and open circuit.
The power supply must be stabilize and protected against shocks, surge, and any
unexpected change in the AC supply.
The power supply shall be electronic and controlled by PC, and the Total harmonic
distortion (THD) shall be less than 0.5%.
The bench shall be provided with error display screen at each meter position.
The bench shall be provided with additional display unit to measure the voltage,
current, power, power factor, and frequency.
The bench shall be provided with handheld terminal, used for entering specific
data of meters such as meter serial number, export of data from handheld to the
adapted control PC shall be carried out by docking station via RS232 or USB interface.
The bench shall comprise the facility to be connected to a computer system for the
purpose of reading and calculations.
The bench shall be provided with two Tool kit suitable for test bench and meters.
A computer system shall consist of the following which should be provided with the
bench :
3 Ghz CPU.
500 GB HD.
2 GB RAM.
1 GB VGA.
LCD Monitor 19.
Wireless keyboard and mouse.
Colored laser printer.
Two licensed original Software (operating system Windows) for
automatic meter test procedures.
Optional offer:
28. The power output should not be less than 1000 VA per phase for the current circuit and
800 VA per phase for voltage circuit with protection against short and open circuit.
10