Professional Documents
Culture Documents
Composite Modeling Handbook For Femap NX Nastran and Ls-Dyna 2015
Composite Modeling Handbook For Femap NX Nastran and Ls-Dyna 2015
HandbookforFemap,NXNastranandLSDYNAUsers
VenkataBheemReddy,SeniorStaffMechanicalEngineer
AdrianJensen,PE,Senior StaffMechanicalEngineer
GeorgeLaird,PhD,PE,PrincipalMechanicalEngineer
PredictiveEngineeringWhitePaper
2015
WHATTHISHANDBOOKCOVERS
Thisnoteisintendedfornewengineersinterestedinmodelingcompositesandexperiencedengineerswhowouldliketo
getacquaintedwiththeFemapinterface.
Thefollowingtopicsarecovered:
o Alittlebackgroundonthemechanicsofcompositesandhowmicromechanicscanbeleveragedtoobtain
compositematerialproperties
o 2Dcompositelaminatemodeling
Definingamaterialmodel,layup,propertycardandmaterialangles
Symmetricvs.unsymmetriclaminateandwhythisisimportant
Resultspostprocessing
o 3Dcompositelaminatemodeling
Definingamaterialmodel,layup,propertycardandply/stackorientation
Whenisa3Dmodelpreferredovera2Dmodel
o Modelingasandwichcomposite
Methodsofmodelingasandwichcomposite
3Dvs.2Dsandwichcompositemodelsandtheirprosandcons
o Failuremodelingofa2Dcompositelaminate
Definingalaminatefailuremodel
Postprocessinglaminateandlaminafailureindices
o Additionalexamplesandtheory
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page2of110
PredictiveEngineeringWhitePaper
2015
TABLEOFCONTENTS
1.
INTRODUCTION...............................................................................................................................................................7
1.1 TERMINOLOGY..................................................................................................................................................................................................7
1.2 TYPESOFMATERIALS.........................................................................................................................................................................................8
2.
1.2.1
AnisotropicMaterial...........................................................................................................................................................................8
1.2.2
OrthotropicMaterial..........................................................................................................................................................................9
1.2.3
IsotropicMaterial...............................................................................................................................................................................9
COMPOSITEMICROMECHANICS...................................................................................................................................10
2.1 RULEOFMIXTURES........................................................................................................................................................................................10
2.1.1
3.
ApplicationExample........................................................................................................................................................................10
LAMINATEMODELINGINFEMAP.................................................................................................................................12
3.1 IMPORTANTENTITIES......................................................................................................................................................................................13
3.2 DEFININGANORTHOTROPICMATERIAL..............................................................................................................................................................14
3.3 UNDERSTANDINGTHELAYUPEDITOR.................................................................................................................................................................15
3.4 PROPERTYCARD:2DLAMINATEMODELING........................................................................................................................................................17
3.5 ASSIGNINGMATERIALANGLES..........................................................................................................................................................................18
3.5.1
DefiningaMaterialAngleontheElement......................................................................................................................................19
3.5.2
DefiningaMaterialAngleinthePropertyCard..............................................................................................................................21
3.5.3
AdvancedApplicationExampleofAssigningMaterialAngletoaComplexGeometry...................................................................22
3.6 PROPERTYCARD:3DLAMINATEMODELING........................................................................................................................................................27
3.7 MULTIMATERIALANGLEEXAMPLEOFA3DCOMPOSITEMODEL...........................................................................................................................28
4.
EXAMPLE1:CREATINGA2DLAMINATEMODELINFEMAP..........................................................................................31
4.1 INTRODUCTION..............................................................................................................................................................................................31
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page3of110
PredictiveEngineeringWhitePaper
2015
4.2 CREATINGTHEMATERIALPROPERTY..................................................................................................................................................................31
4.3 DEFININGTHELAYUP......................................................................................................................................................................................32
4.4 DEFININGTHELAMINATEPROPERTY(PCOMP)...................................................................................................................................................33
4.5 SPECIFYINGMATERIALANGLES.........................................................................................................................................................................34
4.6 ANALYSISSETUPANDPOSTPROCESSING.............................................................................................................................................................34
5.
4.6.1
AnalysisSetManagerSetupforComposites...................................................................................................................................36
4.6.2
PostProcessingtheResults.............................................................................................................................................................37
EXAMPLE2:CREATINGA3DLAMINATEMODELINFEMAP..........................................................................................41
5.1 INTRODUCTION..............................................................................................................................................................................................41
5.2 CREATINGTHEMATERIALPROPERTY..................................................................................................................................................................42
5.3 DEFININGTHELAYUP......................................................................................................................................................................................42
5.4 DEFININGTHELAMINATEPROPERTY(PCOMPS).................................................................................................................................................42
5.5 SPECIFYINGMATERIALANGLES.........................................................................................................................................................................43
5.6 POSTPROCESSINGTHERESULTS........................................................................................................................................................................43
6.
EXAMPLE3:MODELINGASANDWICHCOMPOSITE.....................................................................................................45
6.1 INTRODUCTION..............................................................................................................................................................................................45
6.2 CREATINGTHEMATERIALPROPERTY..................................................................................................................................................................45
6.3 DEFININGTHELAYUP......................................................................................................................................................................................45
6.4 DEFININGTHEPROPERTYCARDS.......................................................................................................................................................................45
6.5 POSTPROCESSINGTHERESULTS........................................................................................................................................................................46
6.6 OTHERMETHODSFORSANDWICHCOMPOSITEMODELING....................................................................................................................................48
7.
LAMINATEFAILURETHEORIESINFEMAP.....................................................................................................................50
7.1 INTRODUCTION..............................................................................................................................................................................................50
7.2 HILLSTHEORY...............................................................................................................................................................................................50
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page4of110
PredictiveEngineeringWhitePaper
2015
7.3 HOFFMANSTHEORY.......................................................................................................................................................................................51
7.4 TSAIWUTHEORY..........................................................................................................................................................................................52
7.5 MAXIMUMSTRAINTHEORY..............................................................................................................................................................................52
7.6 ONSETFAILURETHEORY..................................................................................................................................................................................53
8.
EXAMPLE4:MODELINGTHEFAILUREBEHAVIOROFCOMPOSITELAMINATES...........................................................53
8.1 CREATINGTHEMATERIALPROPERTY..................................................................................................................................................................53
8.2 DEFININGTHELAMINATEPROPERTY...................................................................................................................................................................54
8.3 RESULTS.......................................................................................................................................................................................................54
9.
ADDITIONALREADING..................................................................................................................................................59
10. MATERIALDATABASE....................................................................................................................................................60
11. FOURPOINTBENDINGOFASANDWICHCOMPOSITEUSINGFEMAPANDNXNASTRAN............................................63
11.1
HANDCALCULATION..................................................................................................................................................................................64
11.1.1 BasicLaminate.................................................................................................................................................................................64
11.1.2 SandwichComposite.......................................................................................................................................................................74
11.2
FINITEELEMENTSIMULATION......................................................................................................................................................................80
11.3
SUMMARYOFRESULTS...............................................................................................................................................................................89
12. ADDENDUM..................................................................................................................................................................91
12.1
EXAMPLE1(2DLAMINATEWITHAHOLE)......................................................................................................................................................91
12.1.1 DisplacementContour.....................................................................................................................................................................91
12.1.2 MajorPrincipalStressinPly4(0)...................................................................................................................................................92
12.1.3 UnsymmetricLaminate....................................................................................................................................................................93
12.2
EXAMPLE2(3DLAMINATEWITHAHOLE)......................................................................................................................................................94
12.2.1 DisplacementContour.....................................................................................................................................................................94
12.2.2 MajorPrincipalStressinPly4(0)...................................................................................................................................................95
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page5of110
PredictiveEngineeringWhitePaper
2015
12.2.3 3DSolidLaminatewithOneElementforEachLayerThroughThickness.......................................................................................96
12.3
EXAMPLE3(3DSANDWICHCOMPOSITE).......................................................................................................................................................98
12.3.1 DisplacementContour.....................................................................................................................................................................98
12.3.2 TransverseShearStress(ZX)inCore...............................................................................................................................................99
12.4
EXAMPLE4(2DLAMINATEWITHFAILURE)...................................................................................................................................................100
12.4.1 LaminateFailure............................................................................................................................................................................100
12.4.2 FailureinLongitudinalTension......................................................................................................................................................101
12.4.3 FailureinTransverseTension........................................................................................................................................................102
13. APPENDIX....................................................................................................................................................................103
13.1
CLASSICALLAMINATIONTHEORY.................................................................................................................................................................103
13.1.1 KinematicEquations......................................................................................................................................................................103
13.1.2 ConstitutiveEquations...................................................................................................................................................................103
13.1.3 Resultants......................................................................................................................................................................................104
13.1.4 EquilibriumEquations....................................................................................................................................................................104
13.1.5 StiffnessMatricesA,B,andD........................................................................................................................................................104
13.2
UNSYMMETRICLAYUP..............................................................................................................................................................................106
13.3
CHAMISMODEL......................................................................................................................................................................................108
13.4
ONSETFAILURETHEORY...........................................................................................................................................................................108
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page6of110
PredictiveEngineeringWhitePaper
2015
CompositeLaminateModelingUsingFemap
1.
INTRODUCTION
1.1
TERMINOLOGY
Compositematerial:Acombinationoftwoormorematerialstoformanewmaterialsystemwithenhanced
materialproperties.
Examplesofreinforcementsareglassfibers,carbonfibers,siliconcarbidefibersetc.
Examplesofmatrixmaterialsareepoxy,polyurethane,siliconcarbideetc.
Lamina:Alaminaisathinlayerofcompositematerial.Thethicknessofthelaminaisusually0.1to1mm.Itisalso
referredtoasaply.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page7of110
PredictiveEngineeringWhitePaper
2015
Laminate:Alaminateisconstructedbystackinganumberoflaminae.Thebuildingblockforalaminateislamina.
1.2
TYPESOFMATERIALS
Inengineeringapplications,materialscanbebroadlyclassifiedasanisotropic,orthotropic,andisotropic.Ananisotropic
materialhasthegeneralizedformulation,whileothertwoarederivedbysomesimplifications.
1.2.1
ANISOTROPICMATERIAL
Ananisotropicmaterialhasnoplanesofmaterialsymmetry.Examplesofanisotropicmaterialsarefemur,shortfiber
compositesetc.Thenumberofconstantsrequiredtodescribeanisotropicmaterialsis21.Thestiffnessmatrixshown
belowissymmetricaboutthediagonalterms.Accordingly,allthediagonaltermsandthetermsabove/belowthe
diagonaltermshavetobedefinedinthematerialmodel.
1 C11
C
2 12
3 C13
23 C14
13 C15
12 C16
C12
C 22
C 23
C 24
C13
C 23
C33
C 34
C14
C 24
C 34
C 44
C15
C 25
C 35
C 45
C 25
C 26
C 35
C 36
C 45
C 46
C 55
C 56
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
C16 1
C 26 2
C 36 3
C 46 23
C 56 13
C 66 12
Page8of110
PredictiveEngineeringWhitePaper
1.2.2
2015
ORTHOTROPICMATERIAL
Anorthotropicmaterialhasthreeplanesofmaterialsymmetry.Examplesoforthotropicmaterialsarewood,
unidirectionallaminaetc.Thenumberofconstantsrequiredtodescribeorthotropicmaterialsis9.Thestiffnessmatrixis
symmetricandallthediagonaltermsandtermsabove/belowthediagonaltermshavetobedefined.However,
commercialfiniteelementsoftwareallowdefiningtheelasticmoduli(E1,E2,E3),shearmoduli(G12,G13,G23),and
Poissonsratio(12,13,23)insteadofcalculatingeachofthestiffnessterms.Thefiniteelementsoftwarecaninternally
evaluatethesestiffnessterms.
1 C11
C
2 12
3 C13
23 0
13 0
12 0
1.2.3
C12
C13
C 22
C 23
0
0
0
C 23
C33
0
0
0
0
0
C 44
0
0
0
0
0
C55
0
0 1
0 2
0 3
0 23
0 13
C 66 12
ISOTROPICMATERIAL
Allplanesareplanesofsymmetry.Examplesofisotropicmaterialsaremetalslikesteel,aluminumetc.Thereareonly
2independentconstants(C11andC12)foranisotropicmaterial.Similartotheorthotropicmaterialmodel,onecandefine
Eandinsteadofcalculatingthestiffnessterms.
C11 C12
1 C12 C11
2 C12 C12
3
0
0
23
13 0
0
12 0
0
C12
C12
C11
0
0
0
0
C11 C12
2
0
0
0
0
C11 C12
2
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
1
2
0
3
23
0
13
C11 C12 12
0
0
0
Page9of110
PredictiveEngineeringWhitePaper
2.
2015
COMPOSITEMICROMECHANICS
Studyofcompositematerialbehaviorwhereintheinteractionofconstituentmaterialsareexaminedona
microscopicscaletodeterminetheireffectonthepropertiesofthecompositematerial.
Predictthepropertiesofcomposite,giventhecomponentpropertiesandtheirgeometricarrangement.
Themechanicalpropertiesofthecompositedependonthepercentagesoffibersandmatrix.
2.1
RULEOFMIXTURES
Ifthefiberandmatrixpropertiesareavailable,areasonableestimationofthelaminapropertiescanbeobtained
usingtheruleofmixtures(strengthofmaterialsapproach).
E L E f Vf E m Vm
V V
1
f m
Ef Em
ET
1
V
V
f m
G LT G f G m
LT f Vf m Vm
Here,ELandETcorrespondtolongitudinalandtransversemoduliofthecompositelamina,GLTandLTcorrespondto
inplaneshearmodulusandPoissonsratio,respectively.Suffixfcorrespondstofiberpropertyandmcorresponds
tomatrixproperty.Intheaboveequations,Vcorrespondstovolumefraction.
2.1.1
APPLICATIONEXAMPLE
Wewillconsiderthemechanicalpropertiesofacarbonfiberandanepoxyresintoapplytheruleofmixturesand
estimatethelaminamechanicalproperties.Forthisexample,wewillconsiderafibervolumefractionof56%.For
moststructuralapplications,afibervolumefractiongreaterthan55%istypicallyused.Increasingthefibervolume
fractioncanfavorintermsoftheloadcarryingcapacityasfiberstakemajorityoftheload.However,fibervolume
fractioncannotbeincreasedbeyondacertainlimit(typicallyaround65%).Justasanote,thetheoreticalmaximum
volumefractionforafiber(cylinder)is78%forsquarepacking.Astheresincontentisreduced,fibersarenot
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page10of110
PredictiveEngineeringWhitePaper
2015
completelywetduringthemanufacturingprocessandcanresultinincreaseddryspots(partqualityisreduced).This
willresultinreducedloadtransferbetweenthefibers.
Constituent
EL(GPa)
ET(GPa)
G(GPa)
Vf(%)
Carbonfiber
220
22
0.15
25
56
Epoxyresin
3.3
3.3
0.37
1.2
Thecarbon/epoxylaminapropertiesarecalculatedusingtheruleofmixturesasshownbelow.
EL=220*0.56+3.3*0.44=125GPa
1/ET=(0.56/220)+(0.44/3.3)=0.14GPa>ET=7.4GPa
1/GLT=(0.56/25)+(0.44/1.2)=0.39GPa>GLT=2.6GPa
LT=0.56*0.15+0.44*0.37=0.25
Themechanicalproperties(2Dorthotropic)obtainedusingtheruleofmixturesforacarbon/epoxylaminaareshown
below.
Carbon/epoxylamina
EL(GPa)
ET(GPa)
GLT(GPa)
LT
Ruleofmixtures
125
7.4
2.6
0.25
Chamismodel
125
9.1
4.2
0.25
Experimental[1]
125
9.1
0.34
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page11of110
PredictiveEngineeringWhitePaper
3.
2015
LAMINATEMODELINGINFEMAP
Inthissection,weprovidedetailsonmodelingcompositelaminatesinFemap.Therearefourimportantentitiesinwhich
modelinglaminatesdiffersfromconventionalmetalliccomponents.Compositelaminatemodelingdealswiththe
followingmodifications:
anorthotropic/anisotropic(typically)materialconfiguration
laminateshavealayeredconfiguration,soalayupconfigurationhastobespecifiedwiththethicknessofeach
layerandtheirorientationanglesw.r.tareferenceaxis
anelement/propertytypethataccountsforthelayeredconfigurationhastobeused
referenceaxis(materialangle)specification
EachoftheaboveentitiesandtheirdefinitioninFemapissummarizedinthefollowingsubsections.Therearetwowork
flowsthatcanbefollowedtomodelalaminateinFemapdependingonwhetherthelaminatemodelisa2Dor3D.
Definingthematerialcards,layup,andpropertycardsiscommonbetween2Dand3Dmodels;however,materialangles
canbespecifiedusingtwoapproachesina2Dmodelwhileonlyoneapproachisusedfora3Dmodel.In2Dmodels
materialanglescanbespecifiedatelementlevelordirectlyinthepropertycards.Specifyingmaterialanglesonelements
isaconvenientapproachespeciallyforcomplexgeometries;wecanselectasetofelementsandapplythematerialangle
insteadofassigningaspecificmaterialangletoallelementsinapropertycard.For3Dmodels,wehavetodefine
materialanglesinthepropertycardandsoweneedtocreatemultiplepropertycardsforcomplexgeometries.Inthe
followingsubsections,anoverviewofFemapinterfaceforlaminatemodelingisprovidedaccompaniedbyworked
examples.
Workflow1
Workflow2
laminate (2D)
laminate(2D)andsolidlaminate(3D)
materialmodel
materialmodel
layup
layup
propertycard
propertycardwithmaterialangle
definematerialangleonelement
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page12of110
PredictiveEngineeringWhitePaper
3.1
2015
IMPORTANTENTITIES
Modelingcompositescanbeeasierifthefollowingentitiesarecarefullyassigned.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page13of110
PredictiveEngineeringWhitePaper
3.2
2015
DEFININGANORTHOTROPICMATERIAL
Noticethatwehavedifferentpropertiesinlongitudinal(E1)andtransverse(E2)directions,whereE1isalignedto
theanglespecifiedwithinthelayup.
Dependingonthetypeofanalysis,variousmaterialpropertiesarerequired.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page14of110
PredictiveEngineeringWhitePaper
3.3
2015
UNDERSTANDINGTHELAYUPEDITOR
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page15of110
PredictiveEngineeringWhitePaper
2015
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page16of110
PredictiveEngineeringWhitePaper
3.4
2015
PROPERTYCARD:2DLAMINATEMODELING
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page17of110
PredictiveEngineeringWhitePaper
3.5
2015
ASSIGNINGMATERIALANGLES
Although,orientationanglesarespecifiedforeachlaminaindividuallyinthelayupeditor,Femapwillnotunderstandas
towhichreferencedirectiontheseorientations(angles)correspond.So,weneedtospecifyamaterialanglesuchthatall
orientations(specifiedinlayup)takethisvectorasthereference.Forexample,ifthematerialangleisdefinedinthe
globalxdirectionthenalltheorientationswilluseglobalxdirectionasthereference.Oneshouldnotbeconfusedwith
theterminologiesmaterialangleandorientationangleinthelayupeditor.Materialangleisareferenceaxisthatwe
assigntotheelementandisindependentoftheshapeoftheelement.Orientationangleistheorientationofthelamina
(fiberdirection).Bydefault,Femapassignsnomaterialangle.Useanyofthefollowingmethodstospecifythematerial
angle.
Imagesource:https://www.faa.gov/regulations_policies/handbooks_manuals/aircraft/amt_airframe_handbook/media/ama_Ch07.pdf
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page18of110
PredictiveEngineeringWhitePaper
3.5.1
2015
DEFININGAMATERIALANGLEONTHEELEMENT
Onecandefine/updatethematerialanglesusingtoolbarModify>UpdateElements>MaterialOrientation.
Thismethodallowsonetodefineamaterialangletoaselectedsetofelementsoralltheelementsatatime.Itis
importanttonotethatthematerialangleisindependentoftheelementcoordinatesystemandtheelementshape.For
example,theimagebelowshowselementsthataredistorted.However,thematerialanglesareallalignedtotheglobalx
direction.Ifamaterialangleisnotdefined,Femapwillshowanerrormessage.Ifyoumissdefiningamaterialanglefora
fewelementsinthemodel,itcanbequitedifficulttotracetheelementswithmissingdefinitions.Wehavedevelopedan
APItofiltertheseelementswithmissingelementsandgroupthem.Byaccessingthisnewlycreatedgroup,onecan
assign/updatethematerialanglestotheseelementsonly.TheAPIiscalledCompositesMaterialAngleChecker,andcan
bedownloadedfromourwebsiteathttp://www.appliedcax.com/supportandtraining/apis/apis.html.Onecanverifythe
materialanglesinthelaminateelementsbyselectingthefollowingoptionsunderF6orViewOptions.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page19of110
PredictiveEngineeringWhitePaper
3.5.2
2015
DEFININGAMATERIALANGLEINTHEPROPERTYCARD
Inthisapproach,wecandefineamaterialangledirectlyinthepropertycard.However,thiswillassignthematerialangle
toalltheelementsthatthepropertyidisassociatedwith.Onecanalsochecktheassignedmaterialanglesandupdate
them(incaseofanyincorrectmaterialangles)accordinglyusingtheprocedureinapproach1.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page20of110
PredictiveEngineeringWhitePaper
2015
In case of a complex geometry with curved surfaces, material angles can be effectively defined using the cylindrical
coordinatesystembyusingthetangentdirectionifthevectorhastofollowacurvedsurface.Alwaysremembertoverify
yourmaterialangles!
3.5.3
ADVANCEDAPPLICATIONEXAMPLEOFASSIGNINGMATERIALANGLETOACOMPLEXGEOMETRY
Theexamplebelowshowsacompositewingleadingedge.The0materialangleneedstofollowthecurvatureofthe
leadingedge.However,wecanseefromthepicturethatthevectors(representativeofthematerialangles)donot
followthecurvature.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page21of110
PredictiveEngineeringWhitePaper
2015
Vectorsdonotfollowthe
curvatureoftheleadingedge
In order to assign the material angle accurately, we can use the cylindrical coordinate system (R, T, Z) instead of a
rectangular coordinate system (X, Y, Z). We want to create a new cylindrical coordinate system (instead of an existing
cylindricalcoordinatesystem)thatwilldoabetterjobinaccuratelyassigningthematerialangles.Followthestepsbelow
tocreateanewcylindricalcoordinatesystem.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page22of110
PredictiveEngineeringWhitePaper
2015
Thenewcoordinatesystemisshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page23of110
PredictiveEngineeringWhitePaper
2015
Theaboveprocedurewillorienttheallthematerialanglesalongthecurvatureoftheleadingedge.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page24of110
PredictiveEngineeringWhitePaper
3.6
2015
PROPERTYCARD:3DLAMINATEMODELING
In3Dlaminatemodeling,wedefineaply/stackdirectioninsteadofamaterialangle.Forexample,ifthematerialangleis
inglobalxandthelayupstackinginglobalz,thenwespecifytheply/stackdirectionasXZ(13).Unlike2D,wecannotuse
approach1(Modify>UpdateElements>MaterialOrientation)for3Dsolidlaminateelements.Wecancreatemultiple
propertycards(ifnecessary)withdifferentply/stackdirectionsforsectionsofyourgeometry.Andtrytoexploreother
coordinatesystemsforspecifyingtheply/stackdirection.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page25of110
PredictiveEngineeringWhitePaper
2015
3.7
MULTIMATERIALANGLEEXAMPLEOFA3DCOMPOSITEMODEL
Thisexampleshowsacompositecomponentwithsectionsorientedindifferentdirections.Thecomponentismodeled
usinglaminatesolidelements.Here,wecannotuseasingleply/stackdirectionforallthesectionsofthecomponent.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page26of110
PredictiveEngineeringWhitePaper
2015
In this example, we will create three property cards (identified by color as shown above) to define ply/stack direction
separately for each of the three sections of the composite component. The following images will show how ply/stack
directionshavebeendefinedforthesesections.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page27of110
PredictiveEngineeringWhitePaper
2015
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page28of110
PredictiveEngineeringWhitePaper
4.
2015
EXAMPLE1:CREATINGA2DLAMINATEMODELINFEMAP
4.1
INTRODUCTION
Inthisexample,wewillanalyzeasimplecompositelaminatewithaholesubjectedtouniaxialtension.Composite
laminatesareoftenstudiedforopenholetensionintheaerospaceindustry.Thematerial,layup,andthethicknesses
usedinthisexamplearefromarealworldcompositepart.Here,wewillstudytwotypesoflayupswiththesamenumber
oflayersandsameorientationsbutstackedindifferentways.Wewillanalyzethedifferencesintheresultsjustby
alteringthelayupstackingorder.Wewilllearnthisuniquebehaviorofcompositesbyworkingoutthisexample.With
multiplepliesinthelayup,thisisalsoagoodexampleforpostprocessing.
4.2
CREATINGTHEMATERIALPROPERTY
Thematerialpropertiesusedforthelaminatecorrespondtoaunidirectionalcarbon/epoxylamina.Accordingly,the
materialtypeneedstobe2DOrthotropicforthisproblem.ThematerialpropertiesareshowninTable1.
Table1:MechanicalpropertiesofaunidirectionalT800S/39002lamina
Property
Unit T800S/39002
Longitudinalelasticmodulus(E1)
GPa
147
Transverseelasticmoduli(E2=E3)
GPa
7.58
Inplaneshearmodulus(G12)=Interlaminarshearmodulus(G13)
GPa
3.96
Interlaminarshearmodulus(G23)
GPa
3.00
InplanePoissonsratio(12)=InterlaminarPoissonsratio(13)
0.33
InterlaminarPoissonsratio(v23)
0.38
Longitudinaltensilestrength(Xt)=Longitudinalcompressivestrength(Xc) GPa
2.86
Transversetensilestrength(Yt)=Transversecompressivestrength(Yc)
GPa
1.55
Shearstrength(S)
GPa
0.104
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page29of110
PredictiveEngineeringWhitePaper
2015
Sincethelaminatemodelis2D,thedirection3propertiescanbeignoredforthisproblem.
4.3
DEFININGTHELAYUP
Wewillanalyzetwotypesoflayupsinthismodel.Theideaistoobservehowthelayupcanaffectyouranalysisevenif
thelaminateeffectivelyhasthesamenumberoflayers,sameorientationangles,butstackedupinadifferentsequence.
Layup1:[45/90/45/0]switheachlayerat0.195mmthickness.Thesubscriptsinthelayupdefinitionshowsthatitis
symmetriclaminate.Thisimpliesthatthelayupconfigurationis[45/90/45/0/0/45/90/45].
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page30of110
PredictiveEngineeringWhitePaper
2015
Layup2:[45/90/45/0/45/90/45/0].Layup2has8layersaslayup1exceptthatthelayupconfigurationisno
longersymmetricaboutlaminatesmidplane.
ThelayupeditorwithLayup1definedisshownbelow.Layup2canbedefinedinasimilarmannerbychangingthe
orientationangles.
4.4
DEFININGTHELAMINATEPROPERTY(PCOMP)
TheNastranpropertycardfor2DlaminatesisPCOMP.DetailedinformationonthePCOMPcardisavailableinthe
NastranUserGuide.The2Dlaminateformulationisbasedonclassicallaminationtheory.SelecttheLaminate
element/propertytypeinthepropertycard.Bydefault,Femapassignsplateelementtypefor2Dmodels.Thelayup
definedinthepreviousstepcanbeassignedinthepropertycard.Sincewehavedefinedallthe8layersinthelayup,
optionsislefttoitsdefaultAsSpecifiedinthepropertycard.Alternatively,wecandefine4layersonlyinthelayupand
useSymmetricoption.However,thisoptionhastobeusedwithcautionasitcannotbeusedforunsymmetric
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page31of110
PredictiveEngineeringWhitePaper
2015
laminates.Ideally,onecandefineallthelayersinthelayupeditorunlesstherearealargenumberoflayers(e.g.,thick
composite).
4.5
SPECIFYINGMATERIALANGLES
Forthisproblem,wewilluseglobalxdirectionasourmaterialangle.Wecanuseoneoftheprocedureswhichwere
introducedearlier.
4.6
ANALYSISSETUPANDPOSTPROCESSING
Forthismodel,aforceof10kNisappliedonthenodesononeendandfixedconstraintsareappliedontheotherendas
shownbelow.Tosimulatetheexperimentalloadingbehavior,the10kNloadisappliedonanindependentnodeandthis
nodeisrigidlylinkedtonodesontherightendofthelaminatemodel(shownbelow).Whentheloadisappliedonthe
independentnode,theresultingdisplacementistranslatedtothedependentnodes.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page32of110
PredictiveEngineeringWhitePaper
2015
Themodelisreadytobeanalyzedandissolvedforalinearstaticcase.Themodelisanalyzedforthetwolayupsandthe
deformationsobservedinboththesecasesarediscussed.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page33of110
PredictiveEngineeringWhitePaper
4.6.1
2015
ANALYSISSETMANAGERSETUPFORCOMPOSITES
SRCOMPScontrolsthecomputationandprintoutofplystrengthratios.Whenon,plystrengthratiosareoutputfor
compositeelementsthathavefailureindicesrequested.
NOFISRcontrolstheprintoutofthecompositefailureindicesandstrengthratios.Whenon,thefailureindicesand
strengthratioswillnotbeprinted.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page34of110
PredictiveEngineeringWhitePaper
4.6.2
2015
POSTPROCESSINGTHERESULTS
Initially,themodelwiththesymmetriclaminate([45/90/45/0/0/45/90/45])wasanalyzed.Thetotaltranslation
inthismodelisshownbelow.Thedeformationsaresymmetricaboutthexaxis.Undertheapplieduniaxialtensileload,
deformationswereinplaneasexpected.Nooutofplanedeformationswereobserved.
Next,themodelwithunsymmetriclaminate([45/90/45/0/45/90/45/0])wasanalyzed.Fromthecontours(shown
below),itcanbeobservedthatthedeformationswerenotsymmetricaboutthexaxis.Also,wecannowseethatthe
unsymmetriclaminateresultedinanoutofplanedeformationalthoughtheloadingwasuniaxial.
SymmetriclaminateNo
outofplanedeformations
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page35of110
PredictiveEngineeringWhitePaper
2015
Unsymmetriclaminatewith
outofplanedeformations
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page36of110
PredictiveEngineeringWhitePaper
2015
X29aircraft
PhotocourtesyofStructuralMechanicsCorporation
http://structuralmechanics.com/about/resources/newsletter/articles/youpullittwiststailoredcomposites/
Ifthissubjectinterestsyou,pleaseseetheAppendix.Next,weproceedtostressdistributionsintheindividualplies.For
thisdiscussion,wewillusethesymmetriclaminateresults.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page37of110
PredictiveEngineeringWhitePaper
2015
Thestresscontourshownabovecorrespondstothemajorprincipalstressinply4(0layer).Similarly,wecanplotstress
distributioninotherlayers.Femaphasbunchofoutputoptionsandsometimesitcanbedifficulttofindthesameoutput
vectorforanotherply.TherearesomecustomtoolsavailableinFemapwhichcanbeeffectivelyusedforlaminates.For
example,wecanusetheLaminatePrevPlytooltoplotply3MajorPrincipalStress(providedwehaveaplotofply4
Major Principal Stress) without putting effort in finding the output vector amongst large set of results. This will be
particularlyusefulifyouhavealargenumberoflayersinthelaminate.Someofthetoolswhicharespecifictolaminates
areshownbelow.ThesetoolscanbeaccessedfromCustomTools>PostProcessing.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page38of110
PredictiveEngineeringWhitePaper
2015
IfyouwouldliketousetheseAPIsfrequently,wecancreateacustomizedtoolbarwiththesecommands.Itiseasierthis
waytofindacommandinthetoolbarratherthansearchingforthesecommandsintheCustomTools.Wehavecreateda
videooncreatingacustomizedtoolbarandcanbeaccessedfromhttps://www.youtube.com/watch?v=RT_7uIor6Ww
5.
EXAMPLE2:CREATINGA3DLAMINATEMODELINFEMAP
5.1
INTRODUCTION
Inthisexample,wewilldevelopa3Dlaminatemodeltoanalyzeasimplecompositelaminatewithaholesubjectedto
uniaxialtension.Thisisanextensionofexample1toa3Dlaminatemodel.Thegoalistounderstandtheapplicabilityof
boththemodels.Thematerial,layup,thicknesses,andtheapproachusedinthisexamplearesameasintheexample1.
Amajordifferencebetweenthe2Dlaminatemodelandthe3Dlaminatemodelisthattheformerwillnottakeoutof
planestressesintoaccountwhilethelatterwill.The3Dlaminatemodelswillbeusefulifyouaremodelingacomposite
structurewithfreeedgeslikeholeswheretheoutofplaneshearstressescanbeimportant.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page39of110
PredictiveEngineeringWhitePaper
5.2
2015
CREATINGTHEMATERIALPROPERTY
Definingthematerialpropertiesfora3Dlaminatemodelissimilartothe2Dmodelexceptthatthematerialtypeisnow
3Dorthotropic.Accordingly,direction3propertiesshouldalsobedefined.Alltherequiredpropertiesaredefinedin
Table1.
5.3
DEFININGTHELAYUP
Specifyingthelayupconfigurationissimilartothe2Dcase.However,thematerialproperty(3Dorthotropic)createdin
thepreviousstephastobeusedinsteadof2Dorthotropicpropertiesasinexample1.
5.4
DEFININGTHELAMINATEPROPERTY(PCOMPS)
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page40of110
PredictiveEngineeringWhitePaper
2015
TheNastranpropertycardfor3DlaminatesisPCOMPS.DetailedinformationonthePCOMPScardisavailableinthe
NastranUserGuide.SelecttheSolidLaminateelement/propertytypeinthepropertycard.Bydefault,Femapassigns
Solidelementtypefor3Dmodels.Thelayupdefinedinthepreviousstepcanbeassignedinthepropertycard.The
interfaceforthe3Dlaminatepropertycardisslightlydifferentfromthe2Dcase.HerePly/StackDirectionhastobe
assigned.Forexample,forthe3DlaminatemodelthePly/StackDirectionisspecifiedasXZ(13).Here,Xcorrespondsto
thedirectionofthematerialangle(asdefinedin2Dcase)andZcorrespondstothestackingdirection.Unlikethe2D
laminates,the3Dlaminateformulationisnotbasedonclassicallaminationtheory.
5.5
SPECIFYINGMATERIALANGLES
Theonlydifferencebetweenspecifyingmaterialanglesfora2Dcaseand3Dcaseisthatthe3Dmodelrequiresspecifying
thePly/StackDirection.Theoverallconceptisstillthesame.
5.6
POSTPROCESSINGTHERESULTS
Theimagebelowshowsthefiniteelementmeshofthe3Dlaminatemodel.Inthisexample,onlyonesolidelementis
definedthroughthethickness.Thethicknessoftheelementcorrespondstothetotalthicknessofthelaminate1.56
mm.
Topview
Frontview
1.56 mm
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page41of110
PredictiveEngineeringWhitePaper
2015
The3Dlaminatemodelisanalyzedwiththesymmetriclayupconfiguration.Theobserveddisplacementsandstressesare
shownbelow.Thedisplacementresultsarequitesimilartothe2Dcase.
Themajorprincipalstressdistributioninply4(0layer)isshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page42of110
PredictiveEngineeringWhitePaper
6.
2015
EXAMPLE3:MODELINGASANDWICHCOMPOSITE
6.1
INTRODUCTION
Inthisexample,a3Dsandwichcompositemodelisanalyzedforauniformpressureloading.Thesandwichcomposites
haveacore(e.g.,honeycomb,foam,etc.)sandwichedbetweentwofacesheets.Typically,thefacesheetscarrythe
majorityoftheinplaneandbendingloadswhilethecoretakesshear.Asandwichcompositecanbeconveniently
modeledusingthe2Dlaminatelayupbydefiningthecoreasoneofthelayersinthelayupeditor(shownattheendof
thisexample).Whilethisprocedureiseasy,interlaminarshearstresses(aroundfreeedges)becomeimportantin
sandwichcompositesand2Dlaminatemodels(basedonclassicallaminationtheory)donotaccountfortheoutofplane
stresses.
6.2
CREATINGTHEMATERIALPROPERTY
Twomaterialmodels,eachforthecompositefacesheetandcorearedefined.Thecompositefacesheetismodeledasa
3DorthotropicmaterialandthepropertiesareshowninTable1(example1).Thecoreismodeledasanisotropic
materialwithE=4GPaand=0.25[3].
6.3
DEFININGTHELAYUP
Definingthelaminatelayupforthefacesheetsissameasinexample2.However,itshouldbenotedthatwehavetwo
facesheetsandsowehavetocreatetwosolidlaminatepropertycards,oneforthetopfacesheetandoneforthebottom
facesheet.Iftwolayupsarenotcreatedseparatelyforeachofthefacesheets,wewillseeoutputvectorscorresponding
to8pliesonlyintheresultsset.Iftwolayupsarecreated,thenwecanseeoutputvectorsfor16plies,8forthebottom
facesheetand8forthetopfacesheet.
6.4
DEFININGTHEPROPERTYCARDS
Threepropertycardshavetobecreated,twoofsolidlaminatetypeforfacesheetsandonesolidtypeforthecore.Each
ofthesolidlaminatepropertycardshavetobeassignedtothecorrespondingfacesheets.Thematerialangles
specificationforthesolidlaminatesissimilartothepreviousexample.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page43of110
PredictiveEngineeringWhitePaper
2015
6.5
POSTPROCESSINGTHERESULTS
Clampedboundaryconditionshavebeenappliedonthesandwichcompositeedgesandapressureloadof1MPais
appliedonthetopsurface.
Frontview
Topview
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page44of110
PredictiveEngineeringWhitePaper
2015
Thedeformationplotofthesandwichcompositeduetotheappliedpressureloadisshownbelow.
The interlaminar shear stress distribution in the core is shown below. One can mask the facesheet elements while
plottingtheshearstressdistributioninthecore.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page45of110
PredictiveEngineeringWhitePaper
2015
Thebondbetweenthecoreandfacesheetsisoneofthecriticalregionsfordelaminationinsandwichcomposites.These
interlaminarshearstressesarehigheratthefreeedgesandtheseareasarepotentialregionsfordelaminationinitiation.
One can compare the interlaminar shear stresses to the coretofacesheet bond shear allowable and analyze for any
possibledelaminations.
6.6
OTHERMETHODSFORSANDWICHCOMPOSITEMODELING
Inthisexamplewehavedevelopeda3Dsandwichcompositemodelinwhichthefacesheetsandthecorearemodeledas
solids.Othermethodsbywhichtheaboveproblemcanbeanalyzedare:
1. 2Dsandwichcompositemodelinginwhichthefacesheetsandthecoreareall2Dandcanbedefinedinasingle
layupdefinition.Thisisaconvenientapproachhowever,asdiscussedearlier,the2Dlaminatemodelsarebasedon
classicallaminationtheoryanddonotaccountfortheoutofplanestresses.Secondarymethodsareusedto
estimatetheinterlaminarstresses.
2. Amixof2Dlaminatesand3Dcore.Inthismethod,thefacesheetscanbemodeledas2Dandthecorecanbe
modeledasasolid.Oneshouldbecarefulaboutdefiningthelaminatesforthisconfiguration.Boththefacesheets
havetobeplacedatanoffsetofhalfthelaminatethicknessfromthesolidcore.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page46of110
PredictiveEngineeringWhitePaper
2015
3. Usingtheclassicalplatetheorytomodelsandwichcomposites.Thismodelrequiressomehandcalculationtobe
doneandiscomplexascomparedtothe2Dlaminatemodel.TheNastranpropertycardcorrespondingtotheplate
modelisthePSHELLcard.Inthemethod1describedabove,NastranconvertsaPCOMPpropertyintoan
equivalentPSHELL.So,bothmethod1andmethod2shouldgivesimilarresultsifallthepropertiesareaccurately
defined.Toavoidconfusion,method1ispreferredovermethod2asbotharethesameintermsofhowNastran
interpretsthepropertycard.Alternatively,Femaphasacustomtooltodefineasandwichcompositeusingthe
PSHELLmethod.OnecandohandcalculationsandcomparetheirvalueswiththeFemapcalculatedvalueasshown
below.ThiscustomtoolforsandwichcompositescanbeaccessedfromCustomtools>HoneycombPSHELL>
HoneycombPSHELLProperty.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page47of110
PredictiveEngineeringWhitePaper
7.
2015
LAMINATEFAILURETHEORIESINFEMAP
7.1
INTRODUCTION
Thebehaviorofcompositesiscomplex(asaresultofheterogeneousproperties)whencomparedtomonolithic
materials.Understandingthebehaviorofcompositesunderextremeconditionsofmechanicalloading,temperature,and
otherenvironmentalfactorsposesagreatchallenge.Theeffectoftheseserviceconditionsonthecompositecanrange
fromaminorlossofstiffnessatmicroleveltocatastrophicfailuresatstructurallevel.Themicrostructureofthe
compositeevolvesinmultiplewaysbeforeevidencingmeasurabledegradation.Typicalformsofmicromechanical
failuresincludefiberbreaking,matrixcracking,fiber/matrixinterfacedebondingetc.Factorssuchasmicrocracking
(typicallyinamatrix)areunavoidableandcanbeinherentinthemanufacturedcompositepart.Microcrackingcanresult
fromprocessingthecompositesathightemperatures(curecycle),duetodifferencesofthermal
conductivities/coefficientsofthermalexpansionbetweentheconstituents(fiber,matrix).Otherformsofcomposite
materialpropertydegradationcanresultfromhygrothermalloadingandoxidation.
Inthissection,wewilldealwiththefailureatplylevelandnotthemicromechanicalfailures.Severalfailuretheorieshave
beendevelopedtostudyfailureenvelopesofcompositelaminates.ThefailuretheoriesthatareavailableinFemapare
discussedbelow.Someofthesemodels(maximumstresstheory,maximumstraintheory)arebasedonpurecomparison
ofobservedstresses/strainsinthelaminatewiththeirrespectiveallowables.OthermodelssuchasHillstheory,TsaiWu
theory,andHoffmanstheoryconsiderinteractionoflongitudinal/transversestresses/strainstopredictthefailure
envelope.Althoughfailuretheoriescanbehandytocheckthefailureindicesanddecideiffailureoccursinthelaminate,
itisimportanttounderstandthestressdistributioninthemodel,interlaminarstressesandtheireffectsondelamination,
ABDmatricesetc.
7.2
HILLSTHEORY
Hillsfailuretheoryisapplicablefororthotropicmaterialsthathavethesamestrengthintensionandcompression,
i.e.,Xt=XcandYt=Yc.FailureIndex(FI)isgivenby:
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page48of110
PredictiveEngineeringWhitePaper
2015
Xisallowablestressin1direction
Yisallowablestressin2direction
Sisallowablestressinshear
Xt=Allowabletensilestressin1direction
Xc=Allowablecompressivestressin1direction
Yt=Allowabletensilestressin2direction
Yc=Allowablecompressivestressin2direction
X=Xtif1ispositiveorX=Xcif1isnegativeandsimilarlyforYand2.Fortheinteractionterm12/X2,X=Xtif
12ispositiveorX=Xcif12isnegative.
StrengthRatio(SR)isgivenby,
7.3
HOFFMANSTHEORY
Hoffmanstheoryforanorthotropiclaminainageneralstateofplanestresswithunequaltensileandcompressive
strengthsisgivenby,
Thefailureindexisobtainedbyevaluatingthelefthandsideoftheaboveequation.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page49of110
PredictiveEngineeringWhitePaper
7.4
2015
TSAIWUTHEORY
ThetheoryofstrengthforanisotropicmaterialsproposedbyTsaiandWuspecializedtothecaseofanorthotropic
laminainageneralstateofplanestresswithunequaltensileandcompressivestrengthsis,
Thefailureindexisobtainedbyevaluatingthelefthandsideoftheaboveequation.
F12istobeevaluatedexperimentally.Bydefault,thistermissettozeroinFemap(TsaiWuinteractionterm).
7.5
MAXIMUMSTRAINTHEORY
Themaximumstraincriterionhasnostraininteractionterms.Thefailureindexiscalculatedusing,
X,Y,andSareallowablestrainsinlongitudinaldirection,transversedirectionandinplane,respectively.
Afailureindexformaximumstresstheory(availablefor3Dlaminatemodeling)canbederivedsimilartomaximum
straintheory.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page50of110
PredictiveEngineeringWhitePaper
7.6
2015
ONSETFAILURETHEORY
TheOnsetfailuretheoryortheStrainInvariantFailureTheory(SIFT)iswidelyusedintheaerospaceindustry.Abrief
overviewofthisfailurecriterionisprovidedintheappendix.
8.
EXAMPLE4:MODELINGTHEFAILUREBEHAVIOROFCOMPOSITELAMINATES
Forthisexample,wewillusethe2Dlaminatemodelfromexample1.Allthemodelingprocedurethatwehavedonefor
the2Dlaminatemodelwillbesupplementedbydefiningfailurestrengthsofthelaminaandafailurecriterion.Thegoalis
tostudythefailureincompositelaminatesandalsoexploretheoutputvectorsthatcanbehandyinvisualizingthe
failureatplylevelandlaminatelevel.
8.1
CREATINGTHEMATERIALPROPERTY
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page51of110
PredictiveEngineeringWhitePaper
8.2
2015
DEFININGTHELAMINATEPROPERTY
Thelaminatelayupisthesameasinexample1.Thelaminatepropertycardisalsodefinedinasimilarmanner.
Additionally,wespecifyafailurecriteriontocalculatethefailureindicesatplylevelandforthewholelaminate.Forthis
example,wewillusetheHoffmansfailurecriterion.Thebondshearallowabletermisdefinedtopredictinterlaminar
bondfailure.Ifoneisnotinterestedintheinterlaminarfailure,thistermcanbelefttoitsdefaultvalue0.
Thespecificationofmaterialanglesfollowsthesameapproachasinexample1.
8.3
RESULTS
Inthisexample,wearemainlyinterestedatlookingintothefailureindicesandevaluatethelaminateandindividual
lamina.Auniaxialtensileloadof50kNisapplied.Thecontourbelowshowsthelaminatefailureindexandcanbe
accessedfromtheoutputvector6060LaminateMaxFailureIndex.Thisoutputvectorshowstheoverallfailureindex
ofthelaminate.Acontourvalue(failureindex)greaterthanorequalto1impliesfailure.Basedonthisinformation,one
canassumethatthereareoneormorelayersinwhichthefailurehasoccurred.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page52of110
PredictiveEngineeringWhitePaper
2015
Next,wecancheckthefailureindexoutputvectoronaplybyplybasistofindoutthelayersinwhichthefailurehas
occurred. We can contour the output vector Lam Ply Fib Fail Index for a particular ply and then use the custom tool
optionsLaminateNextPlyorLaminatePrevPlyandcheckthefailureindices.
Within Custom Tools > PostProcessing, Femap has an API for Laminate Envelope Failure Indices. Currently, this API
generatesthesameoutputvectoras6060LaminateMaxFailureIndex.However,thisAPIcanbecustommodifiedto
envelopotheroutputvectors(e.g.,bondfailureindices).
Instead,ifyouareinterestedinmanuallyselectingtheoutputvectorsandenvelopingthemtoasingleoutputvector,you
canuseModel>Output>Process
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page53of110
PredictiveEngineeringWhitePaper
2015
An example of enveloping major principal stresses in all the plies is shown below. This procedure can be followed to
envelopeanyoutputvector.
Iftheanalysishasonlyoneoutputset,thenwecanenvelopetheoutputvectorsfromthatoutputset.However,ifwe
havemultipleoutputsets,thenweneedtoselectoneormoreoutputsetsfromwhichwewouldliketoenvelopethe
outputvectors.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page54of110
PredictiveEngineeringWhitePaper
2015
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page55of110
PredictiveEngineeringWhitePaper
2015
Thiswillcreatenewoutputvectorsasshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page56of110
PredictiveEngineeringWhitePaper
2015
Other output vectors are also created which allow finding the location info (ply and element) of the maximum major
principalstress.Forexample,fromtheabovecontour,wecanseethelocationoftheelementwiththemaximummajor
principalstress.However,wedonotknowtherespective plythathasthismaximumvalue.Thenewlycreatedoutput
vectorEnvelopeLocationInfowillhavethisinformation.Onecanmodifythecontour/criteriastyletodisplayonlythe
maxvalue,minvalueorboth.Because,weareinterestedinmaxvalueonly,requiredchangesweredoneusingF6(View
Options)>PostProcessing>Contour/CriteriaStyle>MaxOnly.Fromthecontourbelow,wecanseethatthemaximum
valueofmajorprincipalstressisobservedinply4.
9.
ADDITIONALREADING
Chapter24:Laminates,NXNastranUsersGuide
PCOMPandPCOMPSinNXNastranQuickReferenceGuide
Chapter6:ElementReferenceLaminateElementandSolidLaminateElementinFemapUserGuide
I.M.DanielandO.Ishai,EngineeringMechanicsofCompositeMaterials,2ndEdition,2005.
R.M.Jones,MechanicsofCompositeMaterials,2ndEdition,1998.
B.D.Agarwal,L.J.Broutman,andK.Chandrashekhara,AnalysisandPerformanceofFiberComposites,3rdEdition,
2006.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page57of110
PredictiveEngineeringWhitePaper
2015
10. MATERIALDATABASE
Thissectionprovidesmaterialpropertiesofsomecommonlyusedfibers(Table2),polymerresins(
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page58of110
PredictiveEngineeringWhitePaper
2015
Table3),andfiberreinforcedpolymercompositematerials(Table4).Typicallyfibersareassumedtobeisotropic.
However,somereferencesalsoconsideredtransverselyisotropicproperties(differentpropertiesinlongitudinaland
transversedirections)forcarbonfibers.Matrixmaterialsaretypicallyisotropicinnature.
Table2:Mechanicalpropertiesofcommonlyusedfibers[4]
Fiber
TensileModulus(GPa)
TensileStrength(MPa)
Density(kg/m3)
EGlass
72.5
3500
2630
SGlass
88
4600
2490
AS4Carbon
245
4000
1800
IM7Carbon
317
4900
1744
Kevlar29
64
2860
1440
Kevlar49
124
3650
1440
Boron
400
3620
2574
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page59of110
PredictiveEngineeringWhitePaper
2015
Table3:Mechanicalpropertiesofcommonlyusedpolymerresins[5]
Resin
TensileModulus(GPa)
TensileStrength(MPa)
Density(kg/m3)
Epoxy
3.5
45
1200
Polycarbonate
2.7
77
1200
Polyethylene
0.7
33
950
Polyurethane
0.025
30
1200
PolyvinylChloride
1.5
60
1400
Table4:Mechanicalpropertiesofcommonlyusedfiberreinforcedpolymercompositematerials
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page60of110
PredictiveEngineeringWhitePaper
2015
11. FOURPOINTBENDINGOFASANDWICHCOMPOSITEUSINGFEMAPANDNXNASTRAN
Inthissection,thesimulationoffourpointbendingtest(ASTMStandardD7249)ofasandwichcompositeispresented.A
detailedhandcalculationispresentedtoobtaintheplylevelstressesandstrains.Thesimulationresultsarealso
comparedwithexperimentaldataandhandcalculation.
Thegeometryandloadingconfigurationofthefourpointbendspecimenareshownbelow.Table5providestheapplied
loadandthespecimengeometryusedinthefourpointbendtest.
Carbon/epoxy
facesheet
(SL)/2
tf
tf
P/2
P/2
L
Honeycomb
core
b
(SL)/2
t
tc
S
0/90/0/90/Core/90/0/90/0
Table5:Geometryandloadingconfigurationofthefourpointbendspecimen
Parameter
Load
SupportSpan
LoadSpan
BeamWidth
BeamThickness
FacesheetThickness
CoreThickness
IndividualPlyThickness
Symbol
P
S
L
b
t
tf
tc
tply
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Value
900.9lbf
22in.
4in.
3in.
1in.
0.02in.
0.96in.
0.005in.
Page61of110
PredictiveEngineeringWhitePaper
2015
11.1 HANDCALCULATION
Wewillfirstshowthehandcalculationsforabasiclaminatewhichwillprovideagoodfoundationforsandwich
composites.Forsandwichcomposites,theconceptandtheequationsaresimilarexceptthatwehavetoaccountfor
facesheetoffsetfromthemidplaneduetothecorethickness.
11.1.1
BASICLAMINATE
Consideraneightplycompositelaminatewith[0/90/0/90]slayupconfiguration( =8).Wehaveanindividualply
=0.005in.Wewillusexyzaxisnotationformaterialaxis(plylevel,localaxis)and123axisforlaminate
thickness
axis(globalaxis).Thisconventionisconsistentwiththenotationusedinthetextbook,IntroductiontoComposite
Materials,byStephenW.TsaiandH.ThomasHahn.Thistextbookwasreferredforthetheoryonflexuralloadingof
compositelaminatesandsandwichcomposites.
x
2
1
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page62of110
PredictiveEngineeringWhitePaper
2015
Wecancalculatethestiffnessterms
foreachplybyusingthefollowingtransformation.
cos ,
sin
Tobetterunderstandthestiffnesstermsinmaterialcoordinatesystem,thefollowingrelationsareprovided.Here,
correspondstotheinplaneshearstress .
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page63of110
PredictiveEngineeringWhitePaper
2015
Theaboverelationsareprovidedintermsofthecompliancematrixasshownbelow(
).
Itiseasiertocalculatethecompliancematrix( )ratherthanthestiffnessmatrix(
becalculatedfromtheelasticpropertiesofaunidirectionallamina(
20.6
,
0.55
,
0.326)asshownbelow.
1
1
20.6
1
1.3
10
10
0.326
20.6 10
1
0.55 10
4.85
10
7.69
10
1.58
1.82
).Thecompliancematrixtermscan
1.3
,
10
10
Now,thestiffnessmatrixcanbeeasilycalculatedbyinvertingthecompliancematrix.
0
0
0
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
0
0
0
Page64of110
PredictiveEngineeringWhitePaper
2015
Weget,
20.7
10
1.31
10
4.27
10
5.50
10
Usingtheoffaxistransformationrelations(providedearlier),wecancalculatethestiffnessterms
0
Stiffnessterm
i,j=1,2,6.
90
20.7
10
1.31
10
1.31
10
20.7
10
4.27
10
4.27
10
5.50
10
5.50
10
Whenacompositelaminateissubjectedtoflexuralloading,themomentcurvaturerelationsareofinterestratherthan
forcestrainrelations(inplaneloadingcase).Themomentsandcurvaturesarerelatedbyanequivalentbendingstiffness
matrixforamultidirectionalcompositelaminate.Wecancalculatethebendingstiffnessmatrix i,j=1,2,6.Fromthe
equationwecaninferthat isdependentonthestackingsequence.
2
3
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page65of110
PredictiveEngineeringWhitePaper
2015
Weget,
0
0
0
78.2 2.28
2.28 39.4
0
0
0
0
2.93
Wecancalculatethebendingcompliancematrixbyinvertingthebendingstiffnessmatrix
0
0
1.28 10
7.40 10
0
2.54 10
0
7.40 10
0
0
0
0
3.41 10
Both and matricesarecomparedwiththevaluescomputedbyFemapandtheywerematchingquitewell.One
canalwaysverifytheirhandcalculationswiththecomputedvaluesfromFemaptodebuganyerrors.Asnapshotofthe
layupconfigurationinputtoFemapisshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page66of110
PredictiveEngineeringWhitePaper
Thecomputed
and
2015
matricesfromFemaparecomparedwiththehandcalculations(shownbelow).
MatrixTerms
BendingStiffnessMatrix
BendingCompliance
Matrix
HandCalculation
Femap
78.2
78.2
39.4
39.4
2.28
2.28
2.93
2.94
1.28
10
1.28
10
2.54
10
2.54
10
7.40
3.41
10
10
7.40
3.40
10
10
Next,wewouldliketoanalyzeplylevelstressesfortheloadingconfigurationshownbelow.Themomentappliedhereis
derivedfromafourpointbendingloadconfigurationwithatotalloadof2lbf.Fromthebendingmomentdiagram,the
momentathalfthelengthofthespecimenis9lbfin.Theplylevelstressevaluationinhandcalculationdoesnotaccount
forthelengthofthespecimen.However,themomentappliedattheendwillbeusedincalculatingthestresses.
1lbf
1lbf
L=11in.
9in.
4in.
9in.
M=9lbfin.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page67of110
PredictiveEngineeringWhitePaper
2015
Inordertocalculatetheplylevelstressesandstrains,weneedtocalculatethecurvaturesusingthemomentsand .
Fromcurvatures,wecancalculatethestrainsandthenstressesfromstrains.Themomentcurvaturerelationisshown
below.Herethemoment isdefinedasthemomentperunitwidth.
Theaboverelationcanbeexpressedintermsofcomplianceasshownbelow([
]=[
]1)
Inourexample,wehave =
/ , =0and
calculatethecurvaturesasshownbelow.
Themomentis
=0. isthetotalmoment.Weknowthemomentsandwecan
1.28 10
7.40 10
0
2.54 10
0
7.40 10
0
0
3.41 10
9lbfin.andthewidthofthespecimenis
3in.
1.28 10
7.40 10
0
Wecancalculatestrainsfromcurvatures.
7.40 10
2.54 10
0
0
0
3.41
10
3
0
0
/
0
0
3.84 10
2.22 10
0
Here, correspondstothedistancefromthemidplaneofthelaminatelayuptomidplaneofaply.
Forthetopmostply(0ply), =0.0175in.Thestrainsinthe0plyareshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page68of110
PredictiveEngineeringWhitePaper
2015
3.84 10
0.0175 2.22 10
0
Wecancalculatestressesinthisplyusingthefollowingrelation.
20.7
4.27
10
10
4.27
1.31
6.72 10
3.89 10
0
10
10
5.50
0
0
10
6.72 10
3.89 10
0
13.9
0.24
0
Thestressescomputedaboveareforthetopplyandweseecompressivestresses.Followingtheaboveprocedure,we
cancalculatethestressesinalltheotherplies.Thedisplacementforthisloadingconfigurationiscalculatedasshown
below.
2
Fromhandcalculations,thedisplacementwas2.3in.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page69of110
PredictiveEngineeringWhitePaper
2015
Table6providestheplylevelstressesfromhandcalculations.
Table6:Plylevelstressescomputedfromtheclassicallaminationtheoryfora[0/90/0/90]slayup
PlyStresses(ksi)
Ply1
Ply2
Ply3
Ply4
HandCalculation
13.9
0.24
0.62
0.37
5.97
0.10
0.12
0.07
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page70of110
PredictiveEngineeringWhitePaper
11.1.2
2015
SANDWICHCOMPOSITE
Intheprevioussection,alltherequiredbasicsarediscussedforanalyzingtheflexuralbehaviorofsandwichcomposite.
Here,weareaddingacoreandseparatingthelaminatedfacesheets.Wewillshowthehandcalculationsforasandwich
compositewithlayupconfiguration[0/90/0/90/Core/90/0/90/0].Thestiffnessmatrices( i,j=1,2,6)willremainthe
sameasweareusingthesameorientations(calculatedintheprevioussectionfora[0/90/0/90]Slayup).Sincethe
stackingsequencenowincludesacore,wehavetoaccountthecorethickness(facesheetseparation)inthebending
stiffnessmatrix( )calculation.
Whenwehaveacoreinthelayup,itistreatedasanequivalentnumberofplies.Accordingly,thelimitsonthe
summationinthebendingstiffnessmatrix[ ]aremodifiedasshownbelow.
2
3
of0and90pliesfromtheprevioussection,weget,
0
0
0
1.07
4.10
10
10
4.10
1.05
10
10
5.28
0
0
10
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page71of110
PredictiveEngineeringWhitePaper
2015
Wecancalculatethebendingcompliancematrixbyinvertingthebendingstiffnessmatrix
0
0
9.37 10
3.66 10
0
9.54 10
0
3.66 10
0
0
0
0
1.89 10
Similartotheprevioussection,wewouldliketoverifythehandcalculationswiththeFemapcomputedvalues.Thelayup
configurationinputtoFemapisshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page72of110
PredictiveEngineeringWhitePaper
Thecomputed
and
2015
matricesfromFemaparecomparedwiththehandcalculations(shownbelow).
MatrixTerms
BendingStiffnessMatrix
BendingCompliance
Matrix
Femap
1.07
10
1.07
10
1.05
10
1.05
10
4.10
10
4.10
10
5.28
10
5.30
10
9.37
10
9.37
10
9.54
10
9.54
10
HandCalculation
3.66
1.89
10
10
3.66
1.89
10
10
Next,wewouldliketoanalyzeplylevelstressesfortheloadingconfigurationshownbelow.Themomentappliedhereis
derivedfromafourpointbendingloadconfigurationwithatotalloadof900.9lbf.Fromthebendingmomentdiagram,
themomentathalfthelengthofthespecimenis4054lbfin.
450.45lbf 450.45lbf
L=11in.
9in.
4in.
9in.
M=4054.05lbfin.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page73of110
PredictiveEngineeringWhitePaper
2015
isdefinedasthemomentperunitwidth.
Themomentcurvaturerelationisshownbelow.Herethemoment
Theaboverelationcanbeexpressedintermsofcomplianceasshownbelow([
]=[
]1)
Inourexample,wehave =
/ , =0and
calculatethecurvaturesasshownbelow.
Themomentis
=0. isthetotalmoment.Weknowthemomentsandwecan
9.37 10
3.66 10
9.54 10
3.66 10
0
0
4054lbfin.andthewidthofthespecimenis
9.37 10
3.66 10
9.54 10
3.66 10
0
0
Wecancalculatestrainsfromcurvatures.
1.89
0
0
0
0
1.89 10
3in.
10
1351.35
0
0
/
0
0
1.27 10
4.95 10
0
Here, correspondstothedistancefromthemidplaneofthesandwichcompositetomidplaneofthecorrespondingply
layer.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page74of110
PredictiveEngineeringWhitePaper
2015
Forthetopmostply(0ply), =0.4975in.Thestrainsinthe0plyareshownbelow.
1.27 10
0.4975 4.95 10
0
Wecancalculatestressesinthisplyusingthefollowingrelation.
20.7
4.27
10
10
4.27
1.31
6.30 10
2.46 10
0
10
10
5.50
0
0
10
6.30 10
2.46 10
0
131
2.37
0
Sinceitisthetopmostply,thestressesarecompressive.Similarly,wecancalculatethestressesinotherpliesby
changingthedistance andalsoaccountingforoffaxistoonaxistransformation.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page75of110
PredictiveEngineeringWhitePaper
2015
Table7providestheplylevelstressesfromhandcalculations.
Table7:Plylevelstressescomputedfromtheclassicallaminationtheoryfora[0/90/0/90/Core/90/0/90/0]layup
PlyStresses(ksi)
HandCalculation
131
2.37
8.06
2.39
128
2.32
7.90
2.34
Ply1
Ply2
Ply3
Ply4
Forthefourpointbendingproblem,thedeflection
.Here,
canbeexpressedas
(refertothe
textbook)
2
3
48
0.6 .
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page76of110
PredictiveEngineeringWhitePaper
2015
11.2 FINITEELEMENTSIMULATION
Ahalfsymmetricmodelofthefourpointbendingspecimenwasusedinthefiniteelementsimulation.Itisimportantto
notethishalfsymmetryapproachwillnotbeapplicablewhenwehaveplyorientationanglesotherthan0and90.The
sandwichcompositeismodeledusinglaminateplateelements(procedurediscussedinsection6.6method1).The
screenshotsofthematerialpropertiesusedforthefacesheetandthecoreareprovidedbelow.Imperialunitsystemwas
usedforthisexample.Theclassicallaminationtheoryassumesthelaminatedplateisnonsheardeformable.Accordingly,
thetransverseshearmoduliofthecorearesettoahighvalue.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page77of110
PredictiveEngineeringWhitePaper
2015
Ascreenshotofthelayupconfigurationusedinthefiniteelementmodelisshownbelow.
Theboundaryconditionsusedinthefiniteelementmodelareshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page78of110
PredictiveEngineeringWhitePaper
2015
Therequiredload(P/2=450.45lbf)wasappliedonthenodesusingacombinationofGAPelementsandRBE2sasshown
below.Thisprocedureallowsforabetterdistributionofloadsonthenodes.Anewsetofnodeshavebeencreatedby
duplicatingandoffsettingthenodesalongtheloadingregionbyafinitedistance(here0.1in.).Thesenewsetofnodes
areconnectedtothecorrespondingnodesontheloadingregionusingGAPelements.TheGAPelementproperties(i.e.,
compressionstiffnessisadjustedinanincreasingfashionuntilthereisaminimalchange(~0.01%)intheforces
distributedonthenodes.AsnapshotoftheGAPelementpropertiesisshownbelow.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page79of110
PredictiveEngineeringWhitePaper
2015
Theloadapplicationprocedureisillustratedbelow.Thefreebodydiagramshowsthenodalforcedistribution.Onecan
manuallycalculatetheforceateachnode(accountingfordifferenceinthecontributionofforceatendnodesandmid
nodes) and compare them with the values obtained using the GAP elements. The latter procedure will give a more
gradualdistributionofforcesascomparedtotheformercase.Anonlinearstaticanalysisisusedinthiscase(withGAP
elements).Thisprocedureisusedasaninitialsteptogettheloaddistributionateachnode.GAPelementsarenonlinear
elementsandwillinvolvestiffnessupdatesduringtheanalysisdependingontheGAPstatus(i.e.,openorclosed).These
GAPstiffnessupdateswillmodifytheglobalstiffnessmatrix.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page80of110
PredictiveEngineeringWhitePaper
2015
InthisexampleGAPelementsareusedonlytogettheloaddistributiononthenodes.Alinearstaticanalysisisperformed
withthenodalforcesobtainedfromanonlinearstaticanalysis.Inthiscase,noGAPelementsareusedandtheforcesare
directlyappliedonthenodes.
Fromthefiniteelementsimulation,themaximumdisplacementinthesandwichcompositeunderfourpointbendingis
0.6in.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page81of110
PredictiveEngineeringWhitePaper
2015
Themaximumtensilestressinthebottomply(0ply1)is131ksi.
Animportantnoteonpostprocessingthesimulationresultsforoffaxisplies(otherthan0forexample90,45etc.)is
thatNXNastranprintsoutstressesinthefiberandmaterialdirectionsandnottheelementcoordinatesystem(aswith
anisotropicmaterial).Wecancheckthisbyprintingthestressesinthe.fo6file.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page82of110
PredictiveEngineeringWhitePaper
2015
Asnapshotofthestressesprintedinthe.fo6fileisshownbelow.
NoticethatNormal1andNormal2conventionisusedunlikeNormalXandNormalY.However,whilepostprocessing
FemapusesthesestressesandstoresthemintheoutputvectorLamPlyXNormalStressandLamPlyYNormalStress.
AlthoughFemapcallsitXNormalStressandYNormalStress,theycorrespondtoNormal1andNormal2respectively.
This implies that Lam Ply X Normal Stress is in the ply fiber direction and Lam Ply Y Normal Stress is in the ply matrix
direction(transversedirection).Ifoneiscomparingwiththehandcalculations,thesestresseshavetobetransformedas
hand calculations correspond to global X and Y directions (or 0 angle for the entire laminate as specified in the
propertycard).Inthisexamplethematerialangle(specifiedonelementpropertycard)isintheglobalXdirection(shown
below).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page83of110
PredictiveEngineeringWhitePaper
2015
Sinceply1is0(inthisexample),notransformationisrequired.Ply2is90andrequirestransformation.Accordingly,the
stressescanbetransformedtoglobalXandYasshownbelow.Thesetransformationshavetobeusedcarefullyasthey
would significantly change the results. Another option is to transform the stresses in the hand calculations to the ply
orientationangle(notransformationinFemapisrequiredinthatcase).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page84of110
PredictiveEngineeringWhitePaper
2015
11.3 SUMMARYOFRESULTS
Fromthefourpointbendingexperimentaltesting,themaximumdeflectionfortheappliedloadwas0.85in.Fromthe
finiteelementsimulationandhandcalculations,thecalculateddisplacementsforthe[0/90/0/90/Core/90/0/90/0]layup
were0.6in.each.Itshouldbenotedthatthethicknessofeachplyusedinhandcalculationsandfiniteelement
simulationwas0.005in.Accordingly,thesandwichintoanequivalentnumberofpliesgivingaroundnumberforthe
handcalculation.Ifanactualthicknessfromtheexperimentwasused,adeflectionwithin10%differencefromthe
experimentalvaluecouldbeobtained.
Thestressescalculatedusingthefiniteelementsimulationandhandcalculationsareshownbelow.Thefiniteelement
simulationwasrepeatedfor[0/45/0/45/Core/45/0/45/0]usingafullmodel(nosymmetrydueto45plies)andthe
stressesarecomparedwithhandcalculations.Itshouldbenotedthattheclassicallaminationtheorydoesnotaccount
forplylevelstressdistributioninthespecimenwidthdirection.Whena[0/90/0/90/Core/90/0/90/0]wasused,the
stressesareuniforminthewidthdirection.However,fora[0/45/0/45/Core/45/0/45/0]layup,thestressesvaryinthe
widthdirectionduetotheoffaxisplies.Asaresult,thesimulatedstressesdeviatefromthehandcalculationswhen
actualspecimenwidthsareusedinthefiniteelementmodel.Toreducethiseffect,aninfinitesimallythinwidthspecimen
hastobemodeledwhenoffaxispliesareusedsuchthatthemodelconformstotheclassicallaminationtheory
assumptionsandsodoestheplylevelstresses.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page85of110
PredictiveEngineeringWhitePaper
2015
Table8providesthecomparisonoftheplylevelstressescomputedusinghandcalculationsandfiniteelement
simulations.
Table8:ComparisonofplylevelstressesbetweenhandcalculationsandFEAresults
Ply
Ply1
Ply2
Ply3
Ply4
(ksi)
0/90/0/90/Core/90/0/90/0
Finite
Hand
Difference
Element
Calculation
(%)
Analysis
131
131
0
0/45/0/45/Core/45/0/45/0
Finite
Hand
Difference
Element
Calculation
(%)
Analysis**
124
124
0
(ksi)
2.37
2.38
0.4
3.26
3.26
(ksi)
2.39
2.40*
0.4
16.5
16.5*
(ksi)
8.06
8.10*
0.5
1.38
1.39*
0.7
(ksi)
128
129
0.8
121
121
(ksi)
2.32
2.33
0.4
3.20
3.20
(ksi)
2.34
2.36*
0.8
16.6
16.7*
0.6
(ksi)
7.90
7.94*
0.5
1.34
1.33*
0.7
*TransformedstressesintofiberandmatrixdirectionstobeconsistentwithFemapoutputvectors
**FEAresultsforthislayuparebasedonalaminatewiththinwidth(0.1in.)
Note:ASTMStandardD7249isoftenusedforevaluatingtheflexuralbehaviorofsandwichcomposites.Thisstandard
providesequationsforcalculatingthestressesinthefacesheetcorrespondingtoamaximumload.However,itshouldbe
notedthatthestandardisnotidealforcalculatingstressesinthefacesheetwithdifferentplyorientations.Rather,the
standardisapplicableforfacesheetswithunidirectionalplyorientationandhomogeneousfacesheets(e.g.aluminum).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page86of110
PredictiveEngineeringWhitePaper
2015
12. ADDENDUM
Inthissection,theexamplespresentedinthewhitepaperwiththeNXNastranSolverarereplicatedusingtheLSDYNA
solver.FemapisthepreprocessorhoweversomemodificationsweredoneinLSPrePostforTSHELL(LSDYNAslayered
solid)elements.ThefollowingisthesummaryofresultsusingtheLSDYNAsolver.Abriefcomparisonoftheresultswas
alsopresentedtounderstandtheapplicabilityofboththesolvers.
12.1 EXAMPLE1(2DLAMINATEWITHAHOLE)
12.1.1
DISPLACEMENTCONTOUR
LSDYNA
NXNASTRAN
Remark:Displacementplotsmatchquitewell
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page87of110
PredictiveEngineeringWhitePaper
12.1.2
2015
MAJORPRINCIPALSTRESSINPLY4(0)
LSDYNA
NXNASTRAN
Remark:MajorPrincipalStressplotsmatchwell.Inordertoanalyzeplylevelstresses,thenumberofintegrationpoints
(plies)inthelaminatehastobeenteredinDATABASE_EXTENT_BINARY(MAXINT=8forthisexample).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page88of110
PredictiveEngineeringWhitePaper
12.1.3
2015
UNSYMMETRICLAMINATE
LSDYNA
NXNASTRAN
Remark:Theoutofplanedeformationsobservedfromboththesolversaresimilar.Althoughthisexampleusesshell
elements,whenmodelinganunsymmetriclaminateinLSDYNA,themoduliandPoissonsratioindirection3(outof
plane)shouldalsobeentered.Otherwise,erroneousresultscanbeencountered.Thereasoningbehindtheoutofplane
deformationsobservedinanunsymmetriclaminatedespitetheuniaxialloadisdetailedintheAppendix.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page89of110
PredictiveEngineeringWhitePaper
2015
12.2 EXAMPLE2(3DLAMINATEWITHAHOLE)
12.2.1
DISPLACEMENTCONTOUR
LSDYNA
NXNASTRAN
Remark:Displacementplotsmatchquitewell
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page90of110
PredictiveEngineeringWhitePaper
12.2.2
2015
MAJORPRINCIPALSTRESSINPLY4(0)
LSDYNA
NXNASTRAN
Remark:Thecontourofthemajorprincipalstressforply4lookssimilarbetweenLSDYNAandNXNastran.However,the
resultsdeviate(maxresultvariesby~19%).TheLSDYNAresultwithTSHELL(thickshell)wasobservedtobesimilarto
shellformulation(example1).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page91of110
PredictiveEngineeringWhitePaper
12.2.3
2015
3DSOLIDLAMINATEWITHONEELEMENTFOREACHLAYERTHROUGHTHICKNESS
Remark:Here,onesolidelementforeachplyisexplicitlydefinedasshownabove.Thisisacomputationallyexpensive
procedurewhichisparticularlysignificantwhenmodelingcompositelaminateswithseverallayers(e.g.,>50).Thisledto
thedevelopmentofaTSHELLelement(discussedpreviously)usingwhichallthepliescouldbedefinedinasingle
elementlayerthroughthelaminatethickness.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page92of110
PredictiveEngineeringWhitePaper
2015
Displacement
contour
MajorPrincipal
StressinPly4(0)
LSDYNA
NXNASTRAN
Remark:Forthisexample,thedisplacementandstressplotsaresimilarbetweentheregularsolidelementandNX
NastransLaminateSolidelement.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page93of110
PredictiveEngineeringWhitePaper
2015
12.3 EXAMPLE3(3DSANDWICHCOMPOSITE)
12.3.1
DISPLACEMENTCONTOUR
LSDYNA
NXNASTRAN
Remark:Displacementplotsmatchwell
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page94of110
PredictiveEngineeringWhitePaper
12.3.2
2015
TRANSVERSESHEARSTRESS(ZX)INCORE
LSDYNA
NXNASTRAN
Remark:Thetransverseshearstressplotsonthecorelooksimilarhowevertheyvaryby~10%.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page95of110
PredictiveEngineeringWhitePaper
2015
12.4 EXAMPLE4(2DLAMINATEWITHFAILURE)
12.4.1
LAMINATEFAILURE
LSDYNA
NXNASTRAN
Remark:Thefailureregionpredictedbyboththesolversissimilar.InLSDYNAaflag=1impliesnofailureandflag=0
impliescompletefailure.Weseethatintheregionsotherthanred,failurehasinitiatedinsomeplies.Theminimalvalue
isnotzeroimplyingthattheelementdidnotfailcompletely.Thismeansthatinsomeplies,forthesameelement,failure
didnotoccur.Forplylevelfailures,LSDYNAcanexplicitlyspecifythemodeoffailurewhereasinNXNastranwesawthat
itonlyindicatesifaplyhasfailedornot(butnotthefailuremode).Inordertoanalyzeplylevelfailures(failuremodes),
additionalhistoryvariablesneedtoberequestedinadditiontospecifyingthetotalnumberofintegrationpoints.The
NEIPSparameterinDATABASE_EXTENT_BINARYissetto6forthisexample.Theoutputvectorcorrespondingtoeachof
thesehistoryvariablesislistedintheLSDYNAmanuals.Forthisexample,wehaveusedMAT_54asourmaterialmodel.
Historyvariable5(forMAT_54)givesthelaminatefailureindex.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page96of110
PredictiveEngineeringWhitePaper
12.4.2
2015
FAILUREINLONGITUDINALTENSION
Remark:Ply4andPly5(0)havepartiallyfailedinlongitudinaltension.Thisisoutputusinghistoryvariable1.
Noneoftheplieshavefailedinlongitudinalcompression(historyvariable2).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page97of110
PredictiveEngineeringWhitePaper
12.4.3
2015
FAILUREINTRANSVERSETENSION
Remark:Plies1,8(45)andPlies3,6(45)havepartiallyfailedintransversetension.Thisisoutputusinghistoryvariable
3.
Noneoftheplieshavefailedintransversecompression(historyvariable4).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page98of110
PredictiveEngineeringWhitePaper
2015
13. APPENDIX
13.1 CLASSICALLAMINATIONTHEORY
Theclassicallaminationtheory(CLT)issimilartotheclassicalplatetheory(CPT),theonlydifferenceisthatCPTassumes
thatthematerialisisotropic,whiletheCLTisanextensiontofiberreinforcedcompositelaminateswithmultiplelayers
resultingincomplicatedstressstrainrelations[6].SimilartotheEulerBernoullibeamtheoryandtheplatetheory,the
CLTisonlyvalidforthinlaminates(spanandwidth>10thinckness)withsmalldisplacementsinthetransversedirection.
ThefourcornerstonesoftheCLTarethekinematic,constitutive,forceresultant,andequilibriumequations.
13.1.1
KINEMATICEQUATIONS
Here,u0,v0,andw0arethedisplacementsofthemiddleplaneinthex,y,andzdirections.Similarly,x0,y0,andxy0are
themidplanestrains,andx,y,andxyarethecurvatures.
13.1.2
CONSTITUTIVEEQUATIONS
th
wherethesubscriptkindicatesthek layercountingfromthetopofthelaminate.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page99of110
PredictiveEngineeringWhitePaper
13.1.3
2015
RESULTANTS
Thetermsonthelefthandsideareforceandmomentresultants.
13.1.4
EQUILIBRIUMEQUATIONS
13.1.5
STIFFNESSMATRICESA,B,ANDD
The relations between the resultants (forces N and moments M) and the strains (strains and curvatures ) are of
interest in composite laminates. By replacing the stresses in the force and moment resultants with strains via the
constitutiveequations,wehave
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page100of110
PredictiveEngineeringWhitePaper
2015
Byapplyingthesummationandintegrationoperationstotheirrespectivecomponents,theforceandmomentresultants
canbeexpressedas,
Theaboveequationscanbeexpressedas,
whereAiscalledtheextensionalstiffness,Biscalledthecouplingstiffness,andDiscalledthebendingstiffnessofthe
laminate.Thecomponentsofthesethreestiffnessmatricesaredefinedasfollows:
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page101of110
PredictiveEngineeringWhitePaper
2015
Heretkisthethicknessofthekthlayerand
isthedistancefromthemidplanetothecentroidofthekthlayer.
13.2 UNSYMMETRICLAYUP
Fromtheclassicallaminationtheory,wehavethefollowingrelationbetweenforce/momentresultants,andthestrains
andcurvatures.
Forexampleconsideronlytheaxialforcecomponent
.Wehave,
2
Page102of110
PredictiveEngineeringWhitePaper
2015
thecomponents
,
,
,and
canexistandwillinfluencethedeformationbehavior.Thecomputeoptionin
layupeditorcanbehandyincheckingthesecomponents.
ForthesymmetriclaminateinExample1,thefollowinginformationisobtainedwhenthecomputeoptionisselected.
WecanseethatallthecomponentsintheBmatrix(couplingstiffnessmatrix)arezero.Thus,wedonotseeanyoutof
planedeformationinthesymmetriclaminatecase.
9.48215E+7
3.01204E+7
0.00000E+0
A Matrix
3.01204E+7
9.48215E+7
0.00000E+0
0.00000E+0
0.00000E+0
3.23506E+7
0.00000E+0
0.00000E+0
0.00000E+0
B Matrix
0.00000E+0
0.00000E+0
0.00000E+0
0.00000E+0
0.00000E+0
0.00000E+0
1.09875E+1
8.07952E+0
5.17406E+0
D Matrix
8.07952E+0
2.34052E+1
5.17406E+0
5.17406E+0
5.17406E+0
8.53069E+0
9.48215E+7
3.01204E+7
0.00000E+0
A Matrix
3.01204E+7
9.48215E+7
0.00000E+0
0.00000E+0
0.00000E+0
3.23506E+7
-1.3176E+4
2.54946E+3
5.31327E+3
B Matrix
2.54946E+3
8.07707E+3
5.31327E+3
5.31327E+3
5.31327E+3
2.54946E+3
2.12521E+1
6.09339E+0
1.03481E+0
D Matrix
6.09339E+0
1.71129E+1
1.03481E+0
1.03481E+0
1.03481E+0
6.54455E+0
Similarly,fortheunsymmetriclaminate,
Now, we see that the B matrix has finite values and as a result, we see outofplane deformation in the unsymmetric
laminate case. This information is quite useful in designing unsymmetric laminates, by tailoring the layup orientation
anglestoretainrequiredmatrixcomponents(ABDmatrices)only.
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page103of110
PredictiveEngineeringWhitePaper
2015
13.3 CHAMISMODEL
13.4 ONSETFAILURETHEORY
Theonsettheory[79]assumesthatthecriticaleffectivepropertiesofthelaminathatcontroldamageinitiationarethe
effective volumetric and equivalent strains of the lamina. Both the volumetric strain and the equivalent strain of the
lamina are defined using strain invariants. The volumetric strain (critical dilatational strain invariant) is defined by the
first invariant of the strain and the equivalent strain (critical distortional strain invariant) is a function of the second
invariantofthestrain.Thestraininvariantsarefunctionsofthreeprincipalstrains.Thevolumetricstrainisgivenby,
Where,
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page104of110
PredictiveEngineeringWhitePaper
2015
1,2,and3arethethreeprincipalstrains
J1,J2,andJ3aretheinvariantsofthestraintensor
Thesignificantcomponentofthevolumetricstrainisthefirstinvariantofstraintensor.Thereducedformofvolumetric
strainisgivenby,
Theequivalentstrain(distortionalstraininvariant,changeinshape)isgivenby,
Fordetailsontheimplementationoftheonsettheory,itisrecommendedtoreadthereferences[79].
REFERENCES
1. H. Altenbach, J. Altenbach, and W. Kissing, Mechanics of Composite Structural Elements, SpringerVerlag Berlin
Heidelberg,NewYork,2004.
2. http://structuralmechanics.com/about/resources/newsletter/articles/youpullittwiststailoredcomposites/
3. R. Seemann and D. Krause, Numerical Modeling of Nomex Honeycomb Cores for Detailed Analyses of Sandwich
PanelJoints,11thWorldCongressonComputationalMechanics,pp.112,Barcelona,Spain,July2025,2014.
4. http://www.engineeringtoolbox.com/polymercompositefibersd_1226.html
5. http://ocw.mit.edu/courses/materialsscienceandengineering/311mechanicsofmaterialsfall
1999/modules/props.pdf
6. http://www.efunda.com/formulae/solid_mechanics/composites/comp_laminate.cfm
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page105of110
PredictiveEngineeringWhitePaper
2015
7. J. Gosse and S. Christensen, Strain Invariant Failure Criteria for Polymers in Composite Materials, 42nd AIAA
Structures,StructuralDynamics,andMaterialsConferenceandExhibit,Seattle,WA,pp.111,2001.
8. L.HartSmith,MechanisticFailureCriteriaforCarbonandGlassFibersEmbeddedinPolymersinPolymerMatrices,
42ndAIAAStructures,StructuralDynamics,andMaterialsConferenceandExhibit,Seattle,WA,pp.111,2001.
9. S. McNaught, Implementation of the Strain Invariant Failure Theory for Failure of Composite Materials, Thesis,
October2009.
10.S.TsaiandH.Hahn,IntroductiontoCompositeMaterials,TechnomicPublishingCompany,Westport,Connecticut,
1980.
Equivalentlaminatemodelsareusefulwhenonlydisplacements,bucklingloadsandmodes,orvibrationfrequenciesand
modesarerequired(Barberobook).
PredictiveEngineeringDocument,FeelFreetoShareWithYourColleagues
Page106of110