Professional Documents
Culture Documents
CL-S700,703,700R TM Eng JN74928-10F
CL-S700,703,700R TM Eng JN74928-10F
CL-S700/CL-S703/CL-S700R
Thermal Transfer Barcode & Label Printer
CL-S700
CL-S703
CL-S700R
JN74928-10F
1.02E-1012
CL-S700/CL-S703/CL-S700R
ii
CHAPTER 1
SPECIFICATIONS
CHAPTER 2
OPERATING PRINCIPLES
CHAPTER 3
CHAPTER 4
TROUBLESHOOTING
CHAPTER 5
PARTS LISTS
CHAPTER 6
CIRCUIT DIAGRAMS
APPENDICES
iii
CL-S700/CL-S703/CL-S700R
Safety Precautions
To prevent personal injury or property damage, the following shall be strictly observed.
The degree of possible injury and damage due to incorrect use/maintenance or improperly
following instructions is described below.
Warning
Caution
Warning
- Before starting disassembly/reassembly or mechanical adjustment, be sure to
disconnect the power cord from the power source.
- Do not replace a fuse with the power switch turned on.
- When replacing a fuse, use the same rating and type since it is provided to prevent
fire and damage to the Unit, Power Supply.
Caution
- DO NOT adjust VR1, VR2, VR3 and VR4 on the SA, Main PCB. (Leave them at the
factory setting condition.) If it is turned, media sensor sensitivity is changed and the
media detection will not be correctly made.
- Do not disassemble/reassemble or adjust the machine, if it functions properly.
Particularly, do not loosen screws on any component, unless necessary.
- After completing an inspection and before turning on the power, be sure to check that
there is no abnormality.
- Never try to print without media.
- Check that the media is properly set.
- Do not lay anything on the cover or lean against it during maintenance or while the
printer is in operation.
- During maintenance, be careful not to leave parts or screws unattached or loose
inside the printer.
- When handling a printed circuit board, do not use gloves, etc., which can easily
cause static electricity. Since ICs, such as CPU, RAM and ROM, might be destroyed
by static electricity, do not touch lead wires or windows unnecessarily.
- Do not put the printed circuit boards directly on the printer or on the floor.
- When disassembling or reassembling, check wires for any damage and do not pinch
or damage them. Also, run wires as they were.
CL-S700/CL-S703/CL-S700R
iv
Chapter 1 Specifications
CHAPTER 1
SPECIFICATIONS
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
Chapter 1 Specifications
Table of Contents
1-1.
1-2.
1-3.
1-4.
CL-S700/CL-S703/CL-S700R
1-2
Chapter 1 Specifications
1-1. General Specifications
Print mode
Batch mode
Tear off mode
Cut mode *1
Peel mode*2
Media
Types of media
Roll, fanfold
(continuous media, die-cuts, continuous tags, paper or tickets)
Recommended media Thermal transfer:
label media (RPR-W Ricoh)
Direct thermal media: label media (150LA-1 Ricoh),
tag media (TB2E0V, Mitsubishi Paper)
Max. media width
118.0 mm
4.65"
Min. media width
25.4 mm
1.00"
Min. label width
7.62 mm
0.30"
*1,*2: Options can be separately purchased.
1-3
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
1-1. General Specifications
6.35 mm
0.254 mm
812.8 mm
6.35 mm
0.0635 mm
0.25"
0.01"
32"
0.25"
0.0025"
8"
1.5 to 3"
1.02, 1.57, or 1.77
CL-S700/CL-S703/CL-S700R
1-4
Chapter 1 Specifications
1-1. General Specifications
1-5
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
1-1. General Specifications
Symbol set
PC866U Ukraina, PC Cyrillic, ISO 60 Danish/Norwegian, DeskTop,
ISO 8859/1 Latin 1, ISO 8859/2 Latin 2, ISO 8859/9 Latin 5, ISO
8859/10 Latin 6, ISO 8859/7 Latin/Greek, ISO 8859/15 Latin 9, ISO
8859/5 Latin/Cyrillic, ISO 69: French, ISO 21: German, ISO 15:
Italian, Legal, Math-8, Macintosh, Math, PC-858 Multilingual,
Microsoft Publishing, PC-8, Code Page 437, PC-8 D/N, Code Page
437N, PC-852 Latin 2, PC-851 Latin/Greek, PC-862 Latin/Hebrew, Pi
Font, PC-850 Multilingual, PC-864 Latin/Arabic, PC-8 TK, Code Page
437T, PC-1004, PC-775 Baltic, Non-UGL, Generic Pi Font, Roman-8,
Roman-9, ISO 17: Spanish, ISO 11: Swedish, Symbol, PS Text, ISO
4: United Kingdom, ISO 6: ASCII, Ventura International, Ventura
Math, Ventura US, Windows 3.1 Latin 1, Wingdings, Windows 3.1
Latin 2, Windows 3.1 Baltic (Latv, Lith), Windows 3.0 Latin 1,
Windows Latin/Cyrillic, Windows 3.1 Latin 5
Control language
Conforms to Datamax programming language*4 and Zebra
programming language*5
Outline of electronic devices
CPU
32-bit RISC CPU
ROM
Standard equipment: FLASH ROM 4M bytes (User area: 1M byte)
RAM
Standard equipment: SDRAM 16M bytes (User area: 1M byte)
CL-S700/CL-S703/CL-S700R
1-6
Chapter 1 Specifications
1-1. General Specifications
1-7
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
1-1. General Specifications
Others
Environment
Humidity %
80
40
30
0
5
35 40
5
Temperature C
-20
60
Temperature C
Storage assurance
temperature
External dimensions
(CL-S700/CL-S703)
External dimensions
(CL-S700R)
Weight
Accessories
Option
CL-S700/CL-S703/CL-S700R
1-8
Chapter 1 Specifications
1-2. Printable Area
Media guide
Printable area
2.5 mm (0.10")
Reference end
Direction of media feed
MODEL
CL-S700/CL-S700R
CL-S703
H
104.0 mm
(4.1)
105.0 mm
(4.1)
1-9
R
11.5 mm
(0.45)
10.5 mm
(0.41)
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
1-3. Printing Position Accuracy
Printable area
100 2 mm*4
(39.4 0.08")
2.5 1 mm*3
(0.10 0.04")
Unprintable area
Unprintable area
1 mm (0.04")
1 2 mm*2
(0.04 0.08")
Reference edge
(Paper guide)
*1:
*2:
*3:
*4:
Actual printing start position. May deviates from the ideal one in the indicated range.
Deviation of vertical positioning when printing position is set to 0.
Deviation of horizontal positioning when printing position is set to 0.
Deviation of vertical printing position when 100 mm is specified from the printing start
position.
CL-S700/CL-S703/CL-S700R
1-10
Chapter 1 Specifications
1-4. Adjustable Sensors/Front Fixed Sensor
2.5 mm
(0.10")
Media
Unprintable area
Unprintable area
6.5 mm (0.2559")
Factory-set position
Printable area
11.5 mm
(0.45")
1-11
CL-S700/CL-S703/CL-S700R
Chapter 1 Specifications
1-4. Adjustable Sensors/Front Fixed Sensor
Center
6.5 mm (0.2559")
2.5 mm
(0.10")
Printable area
CL-S700/CL-S703/CL-S700R
1-12
Unprintable area
Unprintable area
Media
11.5 mm
(0.45")
CHAPTER 2
OPERATING PRINCIPLES
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
2-2
2-3
CL-S700/CL-S703/CL-S700R
SA, Fan
SA, Head Up SW
Unit, Head
Unit, Centro PCB
SA, Cover Open Sens
Unit, Motor
Adjustable Sensor
Part name
Unit, Motor
SA, Head Up SW
(Head Up Sensor)
Adjustable Sensor
CL-S700/CL-S703/CL-S700R
Description
This motor feeds media. A thermistor is attached to this motor to detect
the motor temperature.
This sensor is a mechanical switch to detect the print head position; up
or down.
Consists of the transparent sensor and the reflective sensor that move
to right and left simultaneously by turning the adjust sensor position
knob. Together with the reflective sensor, it is used to detect a label
stuck on liner or a U-shaped notch on tag. The reflective sensor alone
is used to detect the black marks on tag. The media end is detected
with these sensors.
2-4
Part name
Front Fixed Sensor
Description
Consists of the transparent sensor and the reflective sensor.
The function is the same as for adjustable sensor except that this
sensor is fixed and does not move.
This sensor is a photo interrupter to detect the top cover open
status.
This sensor is a photo interrupter to detect the ribbon running. It
also detects the ribbon end. (It is a part of the Unit, Frame Ribbon
L)
This is a thermal head consisting of a head driver and thermal
elements. It incorporates a thermistor to detect the thermal head
temperature.
Consists of LCD, LED and switches for operation.
Controls enter printer system.
This PCB is a connector board of the parallel interface.
Converts AC to DC and feeds DC power to the circuits.
This PCB will be used for optional cutter unit and optional peeler
unit.
Cooling fan that rotates during printing.
2-5
CL-S700/CL-S703/CL-S700R
Part name
SA, Peel Sensor
SA, Rewinder Motor
SA, Interlock SW
(Rewinder Cover Open
Sensor)
SA, Rewinder PCB
CL-S700/CL-S703/CL-S700R
Description
This sensor is a photo reflector to detect the presence of peeled
label at the exit of the printer.
Rewinds the liner of the printed media. It consists of the rewinder
motor, motor control PCB and thermistor that detects the motor
temperature.
This is a mechanical switch to detect the open/close status of the
rewinder cover.
Controls the rewinder operation.
2-6
(Supply Reel)
Ribbon
Thermal Element
Unit, Head
4
Platen
(Unit, Roller Platen)
3
2
2-7
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
2-8
Claw
2-9
CL-S700/CL-S703/CL-S700R
Head Block
Switch OFF
SA, Head Up SW
Switch ON
CL-S700/CL-S703/CL-S700R
2-10
Head Block
25
(mm)
50
75
Slider
100
Head Spring L
Adjust Screw
Head Unit
Media
Platen
Constant
pressure
Head Spring R
Pressure: Low
Pressure: High
2-11
CL-S700/CL-S703/CL-S700R
When wide media is used (need to give strong pressure on the right side):
The same principle applies to wide media. However, in this case, since the media is wide, the
Slider should be moved toward the right (or the Adjust Screw should be turned clockwise) to get
stronger pressure by the Head Spring R.
Head Plate
Offset Spring
Head Unit
(Thermal elements)
Media Thickness
Check Window
Platen
Head Unit
(Thermal elements)
Media Thickness
Check Window
Platen
CL-S700/CL-S703/CL-S700R
2-12
(Rewinder Cover)
SA, Interlock SW
ON
OFF
SA, Interlock SW
2-13
CL-S700/CL-S703/CL-S700R
(Photo Interrupter)
SA, Rewinder Motor
CL-S700/CL-S703/CL-S700R
2-14
Liner
(CL-S700R)
Rewinder Unit
Cutter Position
Sensor
Cutter Motor
Temp. Sensor
Cutter PCB
Rewinder Motor
Temp. Sensor
A/D
Encode Sensor
Rewinder Motor (DC)
Rewinder PCB
(Option) Peeler Unit
Peel Sensor
A/D
RF-ID R/W
(Serial Data)
RS232C
Driver/Receiver
CPU
Head Up Sensor
UPD703111AGM-13-UEU-A
Adjustable Sensor
Peel Sensor
Fan
A/D
A/D
PF Motor
Temp. Sensor
A/D
RS232C
USB 1.1
128MHz
A/D
Thermal Head
Temp. Sensor
D/A Converter
- PF motor current
- PE sensor LED
- Rewind motor current
BZ
Control / C.G.
F-ROM(32Mbit)
Cover Open
Sensor
SA, Ope-pane
PCB
(SW & LED)
Peeler Unit
Main PCB
Ribbon Encoder
A/D
Form Sensor
Connect PCB
Rewinder Cover
Open Sensor
S-DRAM (128Mbits)
PF Motor
Driver
SLA7033M
PF Motor
LCD
(Serial Data)
IEEE1284
Transceiver
Thermal Print
Head
LAN I/F (Option)
Ethernet I/F
Wireless LAN
IEEE1284
2-15
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
2-16
Encode Sensor
Rewinder Motor Temp. Sensor
Description
It is a photo reflector to detect the presence of peeled
label at the exit of the printer.
It is a mechanical switch to detect rewinder cover
open/close status. (SA, Interlock SW)
Two photo interrupters that are used to detect the
amount of liner wounded by the flange. Full state is
also detected. (PS501 and PS502 on the SA,
Rewinder PCB.)
A photo interrupter to detect the running of rewinder
motor. (A part of the SA, Rewinder Motor)
A thermistor attached to the rewinder motor.
(A part of the SA, Rewinder Motor)
(6) Motors
2-17
CL-S700/CL-S703/CL-S700R
PF motor is used. It is a stepping motor to feed media. Ribbon will be fed with the media
through developed friction force.
Rewinder motor is used (CL-S700R only). It is a DC motor to turn the rewinder flange for
winding up liner.
(7) Parallel I/F (IEEE1284)
This is a parallel I/F to transmit and receive parallel data between the printer and a host. It
supports Centronics Compatible mode, NIBBLE mode and ECP mode.
Parallel I/F, serial I/F, or USB I/F is automatically selected when data is received.
(8) Serial I/F (RS-232C)
This is a circuit to transmit and receive serial data between the printer and the host.
Parallel I/F, serial I/F, or USB I/F is automatically selected when data is received.
(9) USB (Universal Serial Bus) I/F
This is a circuit to transmit and receive serial data between the printer and the host using the
USB.
Parallel I/F, serial I/F, or USB I/F is automatically selected when data is received.
(10) Ethernet I/F (Option)
This is a circuit which supports Ethernet protocol. LAN connection is possible.
(11) Wireless LAN I/F (Option)
This is a circuit which supports Ethernet protocol. Wireless LAN connection is possible.
(12) Connect PCB
This is a relay PCB to connect optional peeler unit and auto cutter unit.
CL-S700/CL-S703/CL-S700R
2-18
Command RAM
(Built-in CPU)
CPU
0100000H
0103FFFH
0104000H
0105FFFH
0106000H
0107FFFH
0108000H
010FFFFH
0110000H
027FFFFH
0280000H
03BFFFFH
03C0000H
Flash ROM
4M bytes
Firmware (Datamax)
Firmware (Zebra)
Downloading Area (1M bytes)
04BFFFFH
04E0000H
04EFFFFH
04F0000H
04FFFFFH
0800000H
SDRAM
16M bytes
*: 16K bytes for each I/F
(USB, IEEE1284 and Serial)
4000000H
40FFFFFH
I/O
Custom IC
FFFB000H
FFFEFFFH
FFFF000H
FFFFFFFH
CPU
2-19
CL-S700/CL-S703/CL-S700R
2-2-3. Sensors
(1) Top cover open sensor
The top cover open sensor is used to detect the open/close status of the top cover. This sensor
uses a photo interrupter.
+5V
+3.3V
U1 CPU
P75
CV_OPN R191
173
22
R406
R190
C113
J403
J401
J14
19
22
[Main PCB]
[Ope-pane PCB]
When the top cover is closed, the claw of the top cover is engaged with the photo interrupter
(top cover open sensor). In this case, light emitted from the LED of the photo interrupter is
blocked by the claw and the phototransistor turns OFF. As a result, pin 173 (CV_OPN) of U1
(CPU) goes "High".
When the top cover is opened, the claw is released from the photo interrupter and pin 173
(CV_OPN) of U1 (CPU) goes "Low".
When the top cover is opened, the ERROR LED blinks and the LCD displays ERROR
COVER OPEN on the operation panel.
Top Cover
Claw
CL-S700/CL-S703/CL-S700R
2-20
'(
'(
! "#
$!%
&$
[Rear View]
Head Block
Switch OFF
SA, Head Up SW
Head Block
Switch ON
2-21
CL-S700/CL-S703/CL-S700R
+3.3V
100
R203
LEDMOVE_R
DTA114EM
J7
Q28
2SC5658
LEDMOVE_T
Q9
DTA114EM
Q27
99
[Transparent Sensor]
Q8
R202
2SC5658
SA, Sensor U
1
UP LED A
UP LED K
77
R120
U1 CPU
ANI1
U20B
6
SENSMOVE
C83
- 6
BA2904
Media
R122
DO NOT
ADJUST!
R124
DO NOT
ADJUST!
U4 BH2227
DACIN
12 DI
AO1 1
2 PESENSLED
DACCLK 11
AO2
CLK
CS_DAC 10
R125
AO3 5
CSB
C85
+3.3V
VR4
VR3
P25 145
P23 147
J22
R207
Q21
Q20
5
6
DOWN TR C
DOWN TR E
[Reflective Sensor]
U5B
+
DTC114EM
DTC114EM
DOWN
LED A
DOWN
LED K
BA2904
R126
Q10
C86
R127
2SC5658
[Main PCB]
Caution
-
DO NOT adjust VR3 and VR4 on the Main PCB. (Leave them at the factory
setting condition.) If it is turned, media sensor sensitivity is changed and the
media detection will not be correctly made.
CL-S700/CL-S703/CL-S700R
2-22
The CPU senses this voltage and judges that the light is passing through media, namely, the
liner part without label is now passing through the sensors.
When the label part arrives at the sensors, the light is blocked by the label and does not reach
the phototransistor. So, the phototransistor turns OFF and pin 6 (SENSMOVE) of U1 (CPU)
goes from High to "Low". From this level change, the CPU can detect the leading edge
(arrival) of the label on the liner.
If media runs out, the light directly falls on the phototransistor and the phototransistor
continuously turns ON. From this, media end is detected.
The above principle applies when media with U-shaped notch is used. In this case, since the
light directly falls the phototransistor, the current flowing into the LED (the amount of light
emitted) is appropriately set for detecting the U-shaped notch.
Reflective sensor (used for detecting the black mark on tag):
The reflective sensor alone is used (media sensor menu: Reflect). In this case, pin 100
(LEDMOVE_R) goes High, Q27 and Q8 turn ON and the LED of the reflective sensor turns
ON. The current flowing into the LED (the light amount to be emitted) for detecting black mark
is determined by U4 (D/A converter), U5B and Q10 under the control of the U1 (CPU) and U14
(Custom IC).
When tag with black marks is used, light emitted from the LED is reflected by the tag and
reaches the phototransistor. At the place where no black mark exists, the phototransistor
receives the reflected light and conducts. So, the voltage corresponding to the amount of light
received is applied to the analog input (pin 6 (SENSMOVE)) of U1 (CPU) via U20B. When the
light falls on the black mark, no light is reflected, the phototransistor turns OFF, and pin 6 of U1
(CPU) goes Low.
When media runs out, the light is not reflected by media any more and the phototransistor
continuously turns OFF. From this, media end is detected.
2-23
CL-S700/CL-S703/CL-S700R
+3.3V
94
R201
LEDFIX_R
DTA114EM
J6
Q26
2SC5658
LEDFIX_T
Q7
DTA114EM
Q25
93
[Transparent Sensor]
Q6
R200
2SC5658
SA, Sensor U
1
UP LED A
UP LED K
77
R117
U1 CPU
ANI0
U20A
5
SENSFIX
C81
- 2
BA2904
Media
R118
DO NOT
ADJUST!
R121
DO NOT
ADJUST!
U4 BH2227
DACIN
12 DI
AO1 1
2 PESENSLED
DACCLK 11
AO2
CLK
CS_DAC 10
R125
AO3 5
CSB
C85
+3.3V
VR2
VR1
P25 145
P23 147
J21
R206
Q19
Q18
5
6
DOWN TR C
DOWN TR E
[Reflective Sensor]
U5B
+
DTC114EM
DTC114EM
DOWN
LED A
DOWN
LED K
BA2904
R126
Q10
C86
R127
2SC5658
[Main PCB]
Caution
-
DO NOT adjust VR1 and VR2 on the Main PCB. (Leave them at the factory
setting condition.) If it is turned, media sensor sensitivity is changed and the
media detection will not be correctly made.
CL-S700/CL-S703/CL-S700R
2-24
J3
U1 CPU
ANI2
Thermal Head
19
HDTMP
HDTMP
C64
20
Thermal Head
Temp. Sensor
(Thermistor)
R102
5-8, 21-25
[Main PCB]
Printing
60C
(140F)
(Stop)
(Stops)
70C
(158F)
2-25
CL-S700/CL-S703/CL-S700R
C78
R112
R111
R113
U19A
1
TMPOFF
(To PF Motor Driver)
PF Motor
MOTTMP
VREF
VREF
J5
1
ANI3
R110
[Main PCB]
R114
+
- 2
R115
uPC393GR-9LG
R116
90C
(194F)
Normal speed
(Stop)
95C
(203F)
Low speed
(Stop)
(Stops)
105C
(221F)
In addition to the PF motor temperature rise detection by the CPU, the circuitry composed of
U19A OP amp. detects the high temperature over 130C (266F) to protect the PF motor. If the
PF motor temperature exceeds 130C (266F), the output of U19A is reversed and TEMPOFF
signal goes Low. As a result, +24V supply to the PF motor driver circuit is shut off. (For a
detailed description, refer to 2-2-4 (1) PF motor driver(1) PF motor driver(1) PF motor driver.)
When the PF motor temperature falls below 125C (257F), the output of U19A returns from
Low to High so that +24V supply to the PF motor driver circuit resumes.
CL-S700/CL-S703/CL-S700R
2-26
+3.3V
J8
1
Ribbon Encoder
(Ribbon Running/
Ribbon End Sensor)
R130
U1 CPU
A0
76
R128
RIBENC
C87
R129
[Main PCB]
2-27
CL-S700/CL-S703/CL-S700R
R164
OPN
R166
175
J504
+RW
J502
J16
R513
J702
J701
C100
[SA, Rewinder Motor]
Q507
DTC114EM
[Main PCB]
[Rewinder PCB]
When the rewinder cover is closed, the lever of the SA, Interlock SW (rewinder cover open
sensor) is pressed by A and the switch turns ON. As a result, pin 175 (OPN) of U1 (CPU)
goes "Low".
When the rewinder cover is opened, the switch turns OFF and pin 175 (OPN) of U1 (CPU)
goes "High".
When the rewinder cover is opened, the ERROR LED blinks and the LCD displays Error
Rewinder Open on the operation panel.
(Rewinder Cover)
SA, Interlock SW
ON
OFF
SA, Interlock SW
CL-S700/CL-S703/CL-S700R
2-28
R155
J501 J504
J15
J701
MTTH R16
10
10
11
C98
[Main PCB]
[Rewinder PCB]
Rewinder Motor
100C
(212F)
Printing
(Stop)
2-29
(Stops)
110C
(230F)
CL-S700/CL-S703/CL-S700R
U14
Custom IC
PM1
96
R16
CRPTYP1
J502
J16
J503
+3.3V
U1 CPU
AN17
PEELSENS R168
12
D9
CL-S700/CL-S703/CL-S700R
2-30
[Rewinder PCB]
[Peel Sensor]
2-2-4. Drivers
(1) PF motor driver
This is a driving circuit to drive the PF Motor (stepping motor). The following illustration shows
a simplified circuit. The PF Motor is driven by the unipolar constant current chopper method.
The exciting method for the motor is the 2-phase method.
The power to the PF Motor is supplied by turning ON the FET Q4. This is accomplished by
activating the monostable multivibrator U16A. When U16A is triggered, Q5 turns ON and FET
Q4 turns ON. (TEMPOFF signal is normally at High. If the PF motor temperature rises
excessively, TEMPOFF signal goes Low and the output from U16A is inhibited. Thus, +24V to
the PF Motor is shut off. For TEMPOFF signal, refer to 2-2-3 (6) PF motor temperature
sensor.)
PFMA, PFMA, PFMB and PFMB signals are the exciting pulses to drive the PF Motor.
The digital-to-analog converter (U4) is used to control the PF motor current by applying its
output to pins 3 and 14 (REFA and B) of the motor driver (U18).
U16A
Monostable
Multivibrator
From U1 CPU
From U14 Custom IC
From U1 CPU
PFCLK
PFON
1
2
GRESET
Q 13
A
B
R105
+24V
R104
Q4
XP132A11A1
Q5
DTC114EM
CLR
PFMTCOM
74VHC123
From PF Motor Temp.
Sensor Circuit
TMPOFF
1
2
U18
Motor Driver
4
U17
From U14
Custom IC
From U1 CPU
From U14 Custom IC
PFMA
PFMA
PFMB
PFMB
U4 BH2227
1 PFMOTCU R106
DACIN 12
AO1
DI
DACCLK 11
AO2 2
CLK
CS_DAC 10
AO3 5
CSB
R107
2-31
7
12
6
5
17
16
VSA
VSB
INA
INA
INB
INB
J4
5
2
OUT A
OUT A
OUT B
OUT B
8
1
C69
PF Motor
18
11
C70
3 REFA
14
REFB
C71
SLA7033MPR
[Main PCB]
CL-S700/CL-S703/CL-S700R
HDVON
+3.3V
R93
116
2SJ505S
DTC114EM
R97
C61
U1 CPU
ANI4
VHEAD
Thermal element abnormality check
Q3
DTA114EM
117
HCVON
R95
Q2
+3.3V
HCVON
R96
D1
VHEADMON 9
Q1
R94
HDVON
+24V
R99
R100
10
Q29
DTC114EM
C62
D2
HEADRES
ANI5
HDATA1-4
109-113
108
HDSTB
115
HDCLK
107
HDLTH
HD1-4
HDSTB
HDCLK
HDLAT
U15A
2,4,6,8
A1-4
11
A5
13
A6
16
A7
1,19 OE
Y1-4
Y5
Y6
Y7
18,16,
14,12
J3
+5V
HDTHM1
1-4,26-30
HEADD1-4
10,12,14,17
9
7
9,15
HEADSTB
R101
HEADCLK
16
HEADLAT
18
11
5-8,21-25
74HCT244
[Main PCB]
CL-S700/CL-S703/CL-S700R
13
2-32
Thermal
Head
Q3
U1
CPU
R99
R100
D2
R
10
ANI5
HEADRES
Thermal head
2-33
CL-S700/CL-S703/CL-S700R
DCMTR1 R157
DCMTR1
35 DCMTR0 R156
DCMTR0
U1 CPU
PCS7
PCS4
+RW
J501
1
+24.0V
C507
R163
MTENC
R165
J15
C99
J502
+5.0V
MTREF
+5.0V
R512
R507
R509
+3.3V
176
Q501
2SJ668
Q503
DTC114EM
+5.0V
+5.0V
R508
J16
J504
R505
C506
40
+5.0V
D503
Q502
D502
DTC114EM
D504
R506
MTREF
(+RW Control)
P72
R504
Q504
2SK4033
Q505
DTC114EM
Rewinder Motor
M
Blade
PS701
Q506
DTC114EM
+24.0V Switching Regulator
U501
+RW
ADJ
MTENC
+3.3V +3.3V
U14
Custom IC
R153
HPSENS0 R158
SW6
84
R159
SW5 85
HPSENS1
C96
J15
R154
J501
8
HPSENS0
HPSENS1
C97
+5.0V
+5.0V
R511
R510
PS502
PS501
[Rewinder PCB]
[Main PCB]
CL-S700/CL-S703/CL-S700R
2-34
When Full state (PS501: OFF, PS502:OFF) is detected, rewinding operation stops, and the
ERROR LED blinks and the LCD displays Error Rewinder Full on the operation panel.
SA, Rewinder Flange
Liner
(Photo Interrupter)
SA, Rewinder Motor
2-35
CL-S700/CL-S703/CL-S700R
On Line
Ready
POWER
ERROR
On Line
Ready
Rewind
POWER
FEED
FEED
STOP
PAUSE
ERROR
STOP
PAUSE
MENU
MENU
CL-S700/CL-S703
CL-S700R
CL-S700/CL-S703/CL-S700R
2-36
2-37
CL-S700/CL-S703/CL-S700R
D11.100000000010
30 30 31 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 0010123456789:;<
CL-S700/CL-S703/CL-S700R
2-38
Machine Information
Model Number
Boot Version
ROM Version
ROM Date(DD//MM//YY)
ROMCheck Sum
Head Check
Print Counter
Service Counter
Sensor Monitor
Option Interface
: CL-S700
: ****
: ********
: XX/XX/XX
: ****
: OK
: 0002.234 km
: 0002.234 km
: 1.50 V
: None
: 7 IPS
: 12
: 00
: Thermal Transfer
: 4.00 inch
: 0.00 inch
: 0.00 inch
: 0.00 inch
: Rear Adj Sensor
: See Through
: Off
: 1.00 inch
: PM
: 1.7 V
: 2.80 V
: On Printing
: Off
: On
: Inch
: 10.00 inch
: Off
Off
: STD
: DM4
: On
: Tear
: Backfeed
: 0.00 inch
: Enters Menu
[Interface Menu]
RS-232C Baud rate
RS-232C Parity
RS-232C Length
RS-232C Stop bit
RS-232C X-ON
IEEE 1284
USB Device Class
USB VCOM Protocol
: 9600
: None
: 8 bit
: 1 bit
: Yes
: On
: Printer
: Auto
Note:
Citizen continually enhances
its printers with new options
and settings based on our
customers requests. Extra or
changed menu items may
appear on the print out in some
cases.
2-39
CL-S700/CL-S703/CL-S700R
Main Menu T
Factory Setup
Exit
Enter X
CL-S700/CL-S703/CL-S700R
2-40
Main menu
Factory Setup
T
Service Mode
T
X
W
X
W
Page Setup
T
Submenu
(Factory mode)
Init Fix-Thru
T
ROM Check
T
System Setup
T
S
After Print
Parallel ErrOut
Service Counter
Interface
T
Machine Info
T
Test Mode
T
Global Config
2-41
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
2-42
[Print sample]
Machine Information
Model Number
Boot Version
ROM Version
ROM Date(DD//MM//YY)
ROMCheck Sum
Head Check
Print Counter
Service Counter
Sensor Monitor
Option Interface
: CL-S700
: ****
: ********
: XX/XX/XX
: ****
: OK
: 0002.234 km
: 0002.234 km
: 1.50 V
: None
: 0 dot
: 0 dot
: 0 dot
: 0 dot
: 0 dot
: 0 dot
: 0 dot
: 8 dot
: On
: 0.0 V
: 0.0 V
: 0.0 V
: 0.0 V
: 2.30 V
: 2.10 V
: 2.05 V
: 2.30 V
: 2.10 V
: 2.05 V
: Off
: On
: Dot 1
: Dot 848
: No
: 32 inch
: Normal
: Off
: 0.00 inch
: On
: On
: Off
: 2 sec
: On
: Off
: 7 IPS
: 12
: 00
: Thermal Transfer
: 4.00 inch
: 0.00 inch
: 0.00 inch
: 0.00 inch
: Rear Adj Sensor
: See Through
: Off
: 1.00 inch
: PM
2-43
CL-S700/CL-S703/CL-S700R
: 1.7 V
: 2.80 V
: On Printing
: Off
: On
: Inch
: 10.00 inch
: Off
Off
: STD
: DM4
: On
: Tear
: Backfeed
: 0.00 inch
: Enters Menu
[Interface Menu]
RS-232C Baud rate
RS-232C Parity
RS-232C Length
RS-232C Stop bit
RS-232C X-ON
IEEE 1284
USB Device Class
USB VCOM Protocol
: 9600
: None
: 8 bit
: 1 bit
: Yes
: On
: Printer
: Auto
Note:
Citizen continually enhances
its printers with new options
and settings based on our
customers requests. Extra or
changed menu items may
appear on the print out in some
cases.
CL-S700/CL-S703/CL-S700R
2-44
Caution
- In Factory mode, DO NOT change the factory-set values unless you need to change
them, since there are essential items related to printing accuracy, etc.
- Do not turn OFF the power of the printer until you finish the adjustment. If it is
turned OFF, you need to repeat the adjustment from the beginning.
- The value adjusted here is retained until you change it with the same
procedure. Even if you perform initialization by selecting Test Mode main
menu, Factory Default submenu and Yes, the changed value is not
returned to the initial value set at the factory.
(3-1) Submenu table in Factory mode
The following table shows the submenus of Factory Setup main menu.
*1 [Factory Mode Settings Menu name] in Submenu Name column shows the name
that will be printed in Factory Mode Settings. (Refer to (2) How to print the Factory
Mode Settings menus.)
*2 + shows that the object electrically moves forward/rightward. - shows that the object
electrically moves backward/leftward. 8 dots correspond to 1 mm (203 dots correspond
to 1).
Submenu Name
[Factory Mode Settings
Menu name]
Sens Vol Adj
Adjustable Value
(Default Value)
Description
Displays the level of each media sensor.
Init Fix-Thru
Init Fix-Refl
Init Adj-Thru
Init Adj-Refl
2-45
CL-S700/CL-S703/CL-S700R
Submenu Name
[Factory Mode Settings
Menu name]
Fix-Thru Pos
[Fix Through Sensor Pos.]
Fix-Refl Pos
[Fix Reflect Sensor Pos.]
Adj-Thru Pos
[Adj Through Sensor Pos.]
Adj-Refl Pos
[Adj Reflect Sensor Pos.]
On/Off
(On)
0.0 to 3.3V
(0.0 V)
Fix-Refl LED
[Fix Reflect Sensor]
0.0 to 3.3V
(0.0 V)
Adj-Thru LED
[Adj Through Sensor]
0.0 to 3.3V
(0.0 V)
Adj-Refl LED
[Adj Reflect Sensor]
0.0 to 3.3V
(0.0 V)
CL-S700/CL-S703/CL-S700R
Adjustable Value
(Default Value)
2-46
Description
Electrically shifts the position of transparent
sensor (fixed type) back and forth.
(-32 to +32 mm, -1.26 to +1.26)
Electrically shifts the position of reflective sensor
(fixed type) back and forth.
(-32 to +32 mm, -1.26 to +1.26)
Electrically shifts the position of transparent
sensor (adjustable type) back and forth.
(-32 to +32 mm, -1.26 to +1.26)
Electrically shifts the position of reflective sensor
(adjustable type) back and forth.
(-32 to +32 mm, -1.26 to +1.26)
Electrically shifts the tear off position back and
forth. (-32 to +32 mm, -1.26 to +1.26)
Electrically shifts the cutting position back and
forth. (-32 to +32 mm, -1.26 to +1.26) (Optional)
Electrically shifts the peel position back and
forth. (-32 to +32 mm, -1.26 to +1.26) (Optional)
Electrically shifts the head position to the right or
left side.
(-2 to +4 mm, -0.08 to +0.16)
Automatically controls the light amount of each
media sensor.
This menu is effective when Auto Cal Mode is
set to OFF. The light amount emitted from the
transparent sensor (fixed type) can be changed
manually.
Larger value emits larger amount of light.
This menu is effective when Auto Cal Mode is
set to OFF. The light amount emitted from the
LED of the reflective sensor (fixed type) can be
changed manually.
Larger value emits larger amount of light.
This menu is effective when Auto Cal Mode is
set to OFF. The light amount emitted from the
transparent sensor (adjustable type) can be
changed manually.
Larger value emits larger amount of light.
This menu is effective when Auto Cal Mode is
set to OFF. The light amount emitted from the
LED of the reflective sensor (adjustable type)
can be changed manually.
Larger value emits larger amount of light.
Submenu Name
[Factory Mode Settings
Menu name]
Fix-Thru Level
[Fix Through Cal Level]
0.01 to 3.30V
(2.30 V)
Fix-Refl Level
[Fix Reflect Cal Level]
0.01 to 3.30V
(2.10 V)
Fix-None Level
[Fix SensNone Cal Level]
0.01 to 3.30V
(2.05 V)
Adj-Thru Level
[Adj Through Cal Level]
0.01 to 3.30V
(2.30V)
Adj-Refl Level
[Adj Reflect Cal Level]
0.01 to 3.30V
(2.10 V)
Adj-None Level
[Adj SensNone Cal Level]
0.01 to 3.30V
(2.05 V)
0.01 to 3.30V
(1.50 V)
Through/Reflect
(Reflect)
On/Off
(Off)
On/Off
(On)
Dots 001 to 848
(Dot 001)
Dots 001 to 848
(Dot 848)
Normal/Slow
(Normal)
On/Off
(On)
On/Off
(Off)
Adjustable Value
(Default Value)
2-47
Description
Performs sensitivity adjustment of the front fixed
sensor for Media Sensor menu See Through.
The amount of light received is set to 2.30V.
Performs sensitivity adjustment of the front fixed
sensor for Media Sensor menu Reflect. The
amount of light received is set to 2.10V.
Performs sensitivity adjustment of the front fixed
sensor for Media Sensor menu None. The
amount of light received is set to 2.05V.
Performs sensitivity adjustment of the adjustable
sensor for Media Sensor menu See Through.
The amount of light received is set to 2.30V.
Performs sensitivity adjustment of the adjustable
sensor for Media Sensor menu Reflect. The
amount of light received is set to 2.10V.
Performs sensitivity adjustment of the adjustable
sensor for Media Sensor menu None. The
amount of light received is set to 2.05V.
Sets the threshold value for the peel sensor.
When continuous media is used, selects the
sensor type to be used for detecting paper end.
Sets whether to display the menu of "Double
Heat".
Sets whether to perform head check at power
ON or not.
Designates the start dot for head check.
Designates the end dot for head check.
Sets the ribbon end detection time.
Select whether to activate the Fault signal of
parallel interface at the time of error occurrence.
Select whether to send the serial number to the
host when operating the printer through the USB
interface.
CL-S700/CL-S703/CL-S700R
Position T
+000 dots
Exit
Enter X
5. Press the [MENU] (T) or [FEED] (S) key to increase or decrease the value (or select
a desired option).
In this example, the position of transparent sensor (adjustable type) will be electrically
moved back (-) and forth (+).
6. Press the [STOP] (X) key to save the set value in the printer.
7. Press the [PAUSE] (W) key to return to Factory Setup menu. (To set other submenu,
repeat from Step 2.)
8. Press the [PAUSE] (W) key once again.
The changed value is stored in the printer and the printer is turned OFF and then ON
for normal operation.
CL-S700/CL-S703/CL-S700R
2-48
ROM Check
RAM Check
Motor Feed
Print Counter
Service Counter
Value
Description
Checks the number of defective thermal elements
and displays it. If no defective thermal element is
found, 0000 will be displayed.
Example: PASS
0000dots
Performs ROM checksum test, and displays the
check result (OK or NG) and the checksum value.
Example: PROGRM
OK 4F4E.
Performs RAM capacity check and displays the
check result.
Example: DRAM
OK 16384KByte
Performs motor feed check.
Displays the total printed length since the printer is
firstly used.
Example: Length
1234.567Km
Displays the service counter length in Km since you
reset it last.
Example: Length
0123.456Km
To clear the service counter, press the [Enter] (X)
key.
2-49
CL-S700/CL-S703/CL-S700R
Service Mode T
Head Check
Exit
Enter X
Exit
Enter X
Motor Feed T
Back
Exit
Enter X
6. Press the [MENU] (T) or [FEED] (S) key and select Yes (when Head Check is
selected) or Forward/Back (when Motor Feed is selected).
7. Press the [STOP] (X) key to perform the selected item.
* When Head Check is selected, the number of defective dots of the thermal head is
displayed.
* When Motor Feed is selected, the PF motor turns to feed media forward or backward.
[When Head Check is selected]
[When Motor Feed is selected]
PASS
0000dots
W
Exit
Enter X
Motor Feed T
Forward
Exit
Enter X
CL-S700/CL-S703/CL-S700R
2-50
Exit
Enter X
Length
T
0123.456 km
Exit
Enter X
Reset?
No
Exit
Enter X
Reset?
Yes
Exit
Enter X
2-51
CL-S700/CL-S703/CL-S700R
2-4. Interface
2-4-1. Serial Interface
(1) Specifications
System
Signal level
Baud rate
Data length
Stop bit
Parity
Connector
Signal Abbr.
FG
TXD
Signal name
Frame ground
Transmit Data
RXD
Receive data
RTS
5
6
NC
DSR
Request To
Send
-----Data Set Ready
7
8-13
14
15-19
20
SGND
NC
VCC
NC
DTR
21-25
NC
CL-S700/CL-S703/CL-S700R
Signal ground
-----+5V
-----Data Terminal
Ready
------
Function
Protective grounding
Signal line that transmits data from the printer to
the host
Signal line that transmits data from the host to
the printer
Pulled up to +5.4V through 3.3 k
Not used
Signal line that is active when the host can
interface with the printer
Signal grounding line
Not used
(Factory use only )
Not used
Signal line that is active when the printer can
interface with the host
Not used
2-52
(3) Protocol
XON/XOFF system:
Controlled with the data transmission request signal X-ON (11H) code and the data
transmission stop request signal X-OFF (13H) code.
The conditions for the X-ON code output are as follows:
When the printer is turned from off-line to on-line.
When the remaining of receive buffer is 1024 bytes or more after sending X-OFF code.
The conditions for the X-OFF code output are as follows:
When the remainder of receive buffer is 128 bytes or less.
When the printer is turned from on-line to off-line.
- When the media end is detected.
- When a printer error occurs.
16K
16K bytes
Received data
1024 bytes
X-ON code sending
128 bytes
X-OFF code sending
READY/BUSY System:
DTR signal is controlled with READY ("High")/BUSY ("Low") level.
DTR turns to "High (Ready)" in the following conditions:
When the printer is in on-line mode, and
When the remaining buffer is 128 bytes or more.
(After DTR becomes "High", DTR retains "High" until the remaining buffer becomes 1024
bytes or less.)
DTR turns to "Low (Busy)" in the following conditions:
When the printer is in off-line mode.
When the remaining buffer is less than 128 bytes.
(After DTR becomes "Low", DTR retains "Low" until the remaining buffer becomes 1024 bytes
or more.)
2-53
CL-S700/CL-S703/CL-S700R
Signal level
Signal name
STROBE
DATA0-7
ACKNLG
BUSY
PERROR
SELECT
I/O
Input
Input
Output
Output
Output
Output
AUTOFD
NC
SGND
FGND
P.L.H
GND
PRIME
FAULT
GND
NC
FUSE
SELECTIN
Input
------Output
--Input
Output
------Input
CL-S700/CL-S703/CL-S700R
2-54
Busy:
PError:
Select:
Fault:
Compatible mode
LH
LH
HL
HL
Busy:
PError:
Select:
Fault:
LH
L unchanged
HL
HL
Reset
BUSY
ACK
SELECT
2-55
CL-S700/CL-S703/CL-S700R
Data0~7
Strobe
BUSY
0.5s
0.5s
0.5s
Note:
BUSY goes High at the falling edge of Strobe, and data is latched at the leading edge of
Strobe.
[While receiving PRIME signal]
10~15sec or more
PRIME
BUSY
Ack
Fault
SELECT
Note:
If the PRIME signal width is 10 sec or less, it is not accepted.
BUSY goes to High when the PRIME signal is accepted by the printer.
CL-S700/CL-S703/CL-S700R
2-56
ACK
About 2 sec
Signal code
VBUS
D+
DGND
Signal
USB power
Signal line +
Signal line GND
Function
USB power (+5V)
+ signal line
- signal line
GND
2-57
CL-S700/CL-S703/CL-S700R
CHAPTER 3
DISASSEMBLY AND MAINTENANCE
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-2
(7-2)
Damper Roller (3 pcs.) of the Rewinder Cover block.........................41
(7-3)
Damper Roller (4 pcs.) of the Rewinder Mechanism block ................41
(7-4)
Peel Roll on the Printer part...............................................................41
(8) Removing SA, Rewinder PCB................................................................. 41
(9) Notes on assembling the springs .............................................................. 42
3-6. Adjustments .................................................................................................................... 43
3-6-1. Transparent/Reflective Sensor Position Adjustment............................................. 43
(1) Sensor position adjustment (Factory mode).............................................. 43
(2) Sensor sensitivity adjustment (Factory mode)........................................... 43
(2-1)
Init Fix-Thru sensitivity adjustment ....................................................44
(2-2)
Init Fix-Refl sensitivity adjustment .....................................................46
(2-3)
Init Adj-Thru sensitivity adjustment ....................................................48
(2-4)
Init Adj-Refl sensitivity adjustment .....................................................50
3-6-2. Belt Tension Adjustment ....................................................................................... 52
3-6-3. Ribbon Skew Adjustment ..................................................................................... 53
3-6-4. Ribbon Tension Adjustment .................................................................................. 54
3-3
CL-S700/CL-S703/CL-S700R
Caution
- DO NOT adjust VR1, VR2, VR3 and VR4 on the SA, Main PCB. (Leave them at the
factory setting condition.) If it is turned, media sensor sensitivity is changed and the
media detection will not be correctly made.
- Do not disassemble/reassemble or adjust the machine, if it functions properly.
Particularly, do not loosen screws on any component, unless necessary.
- After completing an inspection and before turning on the power, be sure to check that
there is no abnormality.
- Never try to print without media.
- Check that the media is properly set.
- Do not lay anything on the cover or lean against it during maintenance or while the
printer is in operation.
- During maintenance, be careful not to leave parts or screws unattached or loose inside
the printer.
- When handling a printed circuit board, do not use gloves, etc., which can easily cause
static electricity. Since ICs, such as CPU, RAM and ROM, might be destroyed by static
electricity, do not touch lead wires or windows unnecessarily.
- Do not put the printed circuit boards directly on the printer or on the floor.
- When disassembling or reassembling, check wires for any damage and do not pinch or
damage them. Also, run wires as they were.
CL-S700/CL-S703/CL-S700R
3-4
3-2. Cleaning
Cleaning spots are listed below.
Cleaning Position
Cabinet
Thermal head
Platen
Rollers
(for CL-S700R only)
Media running surface
Description
Wipe soiled parts of the printer with a clean dry cloth. Remove bits
of media, etc., using tweezers.
Note: When cleaning, be careful not to scratch the equipment or to
bend parts, etc.
Clean the thermal head with the head cleaner provided.
Clean the platen with a soft cloth.
Clean the peeler rollers (on the front cover side and printer side)
with a soft cloth.
Wipe off media refuse, etc., on and around the media running
surface.
About 1 drop.
About 3 to 4 drops.
About 0.2 mm thick for grease.
Apply sufficiently.
3-5
CL-S700/CL-S703/CL-S700R
4
5
6
7
8
9
10
11
Name
Phillips Screwdriver
(Length 200 mm)
Phillips Screwdriver
(Length 100 mm)
Flat-blade Screwdriver
(Length 100 mm)
Tweezers
Round Nose Pliers
Cutting Nippers
Soldering Iron (30W)
Volt-ohm Meter
Spring Gauge
Spring Gauge
Hex Wrench
12
Weight
2
3
CL-S700/CL-S703/CL-S700R
Q'ty
1
Description
For 3~4 mm screws
4.3 mm width
1
1
1
1
1
1
1
1
1
2000gf
500gf
2 mm
450g
3-6
Remarks
See 3-5-1.
See 3-5-2.
See 3-5-3.
See 3-5-7.
See 3-5-4.
See 3-5-6.
SA, Fan
See 3-5-8.
See 3-5-12.
See 3-5-13.
See 3-5-14.
See 3-5-15.
Unit, Frame U
See 3-5-16.
3-7
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-8
Caution
- Carefully handle the Unit, Head when disassembling and reassembling so as not to
damage the thermal elements of the Unit, Head. Especially, avoid contacting the
thermal elements with the metal part, etc.
The Unit, Head can be removed easily without detaching any other parts.
1.
2.
3.
4.
Screw
(Head Open Lever)
Head Earth Plate
SA, Head Cable
Unit, Head
Notes on reassembling:
When attaching the Unit, Head, do not strongly push it against the head block. The Head Earth
Plate may come off if you push the Unit, Head strongly.
Securely fasten the Unit, Head with the screw.
When you replace the Unit, Head with a new one, adjust the angle of head spacer shaft, if
ribbon wrinkles are not removed. (This adjustment will be required only when satisfactory results
are not obtained by adjusting the ribbon tension with the adjusting screws of the Unit, Ribbon
Frame L.)
Refer to 3-6-3. Ribbon Skew Adjustment.
3-9
CL-S700/CL-S703/CL-S700R
BH, M3x5K
Cover, Pulley
Note on reassembling:
Be sure that the Belt, Platen Drive is securely installed on the gear of the Unit, Roller
Platen via the Unit, Tension Plate.
CL-S700/CL-S703/CL-S700R
3-10
E-ring, 4
Note on reassembling:
Insert the plastic washer into the projection of the Gear, One-way (on the gear part side).
Then, insert the Gear, One-way into the shaft of the Unit, Roller Platen, while facing the
gear part of the Gear, One-way toward the Unit, Roller Platen.
E-ring, 4
Gear, One-way
Gear part
Plastic washer
3-11
CL-S700/CL-S703/CL-S700R
(Blue Tape)
Cover, LCD
PHT (#2), M3x6
SA, Cover Open Sens
PHT (#2), M3x6
Sheet, Ope-Pane
BH, M3x5
B
Switch, Feed
Switch, Stop
Switch, Menu
Switch, Pause
Cover, Ope-Pane
Notes on reassembling:
Assemble each switch in place.
When assembling the SA, Ope-pane Plate in the Ope-pane Cover block, fit the holes A and
B to the protrusions.
Insert the Cable Ope-pane FFC with its blue tape facing up.
CL-S700/CL-S703/CL-S700R
3-12
6.
7.
8.
9.
Open the top cover and remove 4 screws (1BH, M3x5), then detach the Top Cover block.
Open the head block by pushing the head open lever.
Open the sensor arm block by pushing the sensor arm open lever.
Remove 1 screw (2BH, M3x5) and detach the Cover, Inner Paper.
On the left rear side of the printer, remove 4 screws (3BH, M3x5K) and 1 screw (4BH, M3x5).
Then, while pushing the rear cover toward the rear to make a clearance, remove the Inner
Power Cover block to the right. (See the magnified figure.)
Remove 2 cable clamps. (Access to their locks from the bottom of the printer and release the
locks.)
Remove 1 screw (5BH (N), M4x4) and 1 toothed lock washer (5EXT, T (N), 4).
Remove 1 screw (6BH, M3x5K) and 2 screws (7PH (SW+PW), M3x5), and detach the Plate,
Power (with Unit, Power Supply) to the right.
Disconnect 2 connectors and remove 4 screws (8PH (SW+PW), M3x5) from the Unit, Power
Supply. (Before disconnecting the upper right connector, release its lock.)
3-13
CL-S700/CL-S703/CL-S700R
Notes on reassembling:
When connecting connectors to the Unit, Power Supply, be sure to insert them securely.
Pass the wires into the cable clamp as they were.
When fastening the earth wire of the Unit, Power Supply to the chassis with the screw (5) and
the toothed lock washer (5), be sure to check the earth wire of the AC outlet runs as follows.
If not arrange it as shown.
Caution
- To satisfy the regulated standards, run the earth wire of the AC outlet as shown
above.
CL-S700/CL-S703/CL-S700R
3-14
2
3
BH, M3x3K
Unit, PCB
3-15
CL-S700/CL-S703/CL-S700R
J7 J6
J9
J8
J16
J22 J21
J12
Adjustable Sensor
(Reflective sensor)
J11
J14
J3
J5
J15
J4
Front
Unit, Head
(Blue Tape)
7. Open the Clamp, Main Cable and take out each cable.
In the above figure, the cable of which connector color is tinted (blue) runs through the
Clamp, Main Cable.
They are J4, J5, J6, J7, J8, J9, J21 and J22.
Notes on reassembling:
Clamp the following cables with the Clamp, Main Cable.
The cables with tinted (blue) connectors in the above figure:
J4, J5, J6, J7, J8, J9, J21 and J22.
Insert the Cable, Ope-pane FFC with its blue tape facing the right.
(2) Removing SA, Main PCB and Unit, Centro PCB
1. Remove all connectors from the SA, Main PCB. (See above.)
2. On the rear right of the printer, remove 3 screws (BH, M3x5K) and detach Unit, PCB.
(See the figure on the previous page.)
3. Disconnect the SA, Centro Cable [14-1] from the SA, Main PCB [14-2] and the Unit,
Centro PCB [14-4].
4. Remove 2 lock screws [14-5] and 2 screws (PH (SW+PW), M3x5), and detach the SA,
Main PCB [14-2] from the SA, Holder I/F [14-3].
5. Remove 2 screws (BH, M3x5) [14-7] and detach the Unit, Centro PCB [14-4] from the
SA, Holder I/F [14-3].
CL-S700/CL-S703/CL-S700R
3-16
3-17
CL-S700/CL-S703/CL-S700R
Unit, Mechanism
Power Switch
J3
J12
J15
1
Cable Cover
2
SA, Ope-Pane
Cable, Ope-Pane
FFC
SA, Case L
A
SA, Front Center
5
6
CL-S700/CL-S703/CL-S700R
3-18
Notes on reassembling:
Fit the holes in the chassis of the Unit, Mechanism to the protrusions of the SA, Case L to
securely seat the Unit, Mechanism onto the SA, Case L.
Securely fasten the earth wire with the screw (8PH (SW+PW), M3x5).
Install the Power Switch as shown in the figure (set its l (ON) side to the right).
When assembling the SA, Front Center, assemble it so that its claws A shown in the figure
are securely inserted into the slits B on the SA, Case L.
See the following wiring route for Unit, Mechanism and pass the cables (J4 to J9, J21 and J22)
through the Clamp, Main Cable.
[Wiring route for Unit, Mechanism]
J7
J22
J3
J16
J15
Other Connectors
(J4, J5, J6, J8, J9, J21)
Clamp, Main Cable
When assembling the Cable Cover, first insert its right side while aligning the slit C and then fit
the Cable Cover by shifting in the direction of the arrow
Also, be sure that the cables are correctly routed in the Cable Cover as shown below.
3-19
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-20
3-21
CL-S700/CL-S703/CL-S700R
Spring, Damper R
Spring, Damper L
CL-S700/CL-S703/CL-S700R
3-22
3-23
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-24
3-25
CL-S700/CL-S703/CL-S700R
A
Shaft, Ribbon Guide FF
Bushing (24400680)
(Frame Ribbon L Block)
3
1
2
CL-S700/CL-S703/CL-S700R
3-26
Notes on reassembling:
When reassembling the Unit, Frame Ribbon L, follow the next steps.
1. While pushing down the Ribbon Guide Roller C, insert the shaft B of the Frame Ribbon L
block into the hole C of the Unit, Frame Rear.
(Frame Ribbon L Block)
Unit, Frame Rear
B
Ribbon Guide Roller C
3-27
CL-S700/CL-S703/CL-S700R
2. While tilting the Frame Ribbon L block to the left (outer ward) a little, engage the SA, Front
Tension Arm with the SA, Frame Ribbon R (arrow 1).
At the same time, hook the Spring, Guide Shaft FF on the SA, Front Tension Arm. Be sure
that both ends of the spring are correctly hooked as shown in the enlarged illustration.
3. Next, engage the left side of the SA, Front Tension Arm with the Frame Ribbon L block (arrow
2).
4. Assemble the Bushing (24400680), Shaft, Ribbon Guide FF and Bushing (24400670). For
Bushing (24400670), lock its end by turning it so that the protrusion A is seated securely.
!"
#
$
$
%
$
CL-S700/CL-S703/CL-S700R
3-28
3-29
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-30
3-31
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
3-32
3-33
CL-S700/CL-S703/CL-S700R
BH, M3x5
PH, M3x12
PH (SW+PW), M3x5
Cable, Ope-pane FFC
BH, M3x5K
SA, Ope-pane
CL-S700/CL-S703/CL-S700R
3-34
(Printer Part)
Slits(6 pcs.)
Claws (6 pcs.)
J15
(Rewinder Part)
J16
J502
J501
SA, Rewinder PCB
9. Remove the Printer part and place it so as not to damage the cables at the bottom.
The following is an example where spacers (not supplied) are used.
Cables
(Printer Part)
Spacer
Spacer
3-35
CL-S700/CL-S703/CL-S700R
6
6
3
Torque Limiter
(Door Shaft Block)
E-Ring, 4 4
Pin, Parallel(A), M2x12 5
J504
J503
2
(Rewinder Mechanism
Block)
SA, Rewinder PCB
CL-S700/CL-S703/CL-S700R
3-36
SA1, Peeler
Door, Rewinder
Handle
A
(To J504)
(Cable path)
(To J503)
3-37
CL-S700/CL-S703/CL-S700R
Spring, L Friction
5
Plate1, Peeler
A
4
Spring, R Friction
Roller, Friction
Notes on reassembling:
Distinguish the Spring, L Friction from Spring, R Friction referring to above figure.
The former is longer than the latter.
Securely insert the edges A of the Plate, Friction Link into the slits B.
CL-S700/CL-S703/CL-S700R
3-38
E-Ring, 3
Spring, Rewinder Motor
PHT (#2), M3x6
PH (SW+PW), M3x5
Note on reassembling:
After assembling the SA, Rewinder Motor on the frame, be sure that it can smoothly turn.
(The pivot is the supporting point of the SA, Rewinder Motor.)
3-39
CL-S700/CL-S703/CL-S700R
Plate, Nut
SA, Interlock SW
Connector of the
SA, Rewinder Motor
PH (PW), M2x10
Note on reassembling:
Horizontal long hole is provided for mounting the lower side of the SA, Interlock SW.
When assembling the Plate, Nut, be sure that the lower side of screw is at the center of the
long hole as shown in the figure.
Plate, Nut
Long hole
CL-S700/CL-S703/CL-S700R
3-40
3-41
CL-S700/CL-S703/CL-S700R
Spring, Handle R
CL-S700/CL-S703/CL-S700R
3-42
3-6. Adjustments
3-6-1. Transparent/Reflective Sensor Position Adjustment
When you replace one of the following parts, perform both sensor position adjustment and sensor
sensitivity adjustment.
SA, Main PCB
SA, Sensor U (Fixed type)
SA, Sensor Bottom (Fixed type)
SA, Sensor U (Adjustable type)
SA, Sensor Bottom (Adjustable type)
(1) Sensor position adjustment (Factory mode)
After entering Factory mode, adjust the following submenu items:
Fix-Thru Pos (When SA, Sensor U (Fixed type) or SA, Main PCB is replaced.)
Fix-Refl Pos (When SA, Sensor Bottom (Fixed type) or SA, Main PCB is replaced.)
Adj-Thru Pos (When SA, Sensor U (Adjustable type) or SA, Main PCB is replaced.)
Adj-Refl Pos (When SA, Sensor Bottom (Adjustable type) or SA, Main PCB is replaced.)
For details, refer to 2-3-4. Factory/Service mode in Chapter 2.
(2) Sensor sensitivity adjustment (Factory mode)
Caution
- DO NOT adjust other submenus that are not explained here since the submenus in
Factory mode are essential items that can affect to the printing accuracy, etc.
- Do not turn OFF the power of the printer until you finish the adjustment. If it is
turned OFF, you need to repeat the adjustment from the beginning.
- The value adjusted here is retained until you change it with the same
procedure. Even if you perform initialization by selecting Test Mode main
menu, Factory Default submenu and Yes, the changed value is not
returned to the initial value set at the factory.
Perform sensitivity adjustment for each sensor with the following submenu.
Submenu
Adjust when the following part is replaced.
Init Fix-Thru
SA, Sensor U (Fixed type) or SA, Main PCB
Init Fix-Refl
SA, Sensor Bottom (Fixed type) or SA, Main PCB
Init Adj-Thru
SA, Sensor U (Adjustable type) or SA, Main PCB
Init Adj-Refl
SA, Sensor Bottom (Adjustable type) or SA, Main PCB
Refer to
(2-1)
(2-2)
(2-3)
(2-4)
Refer to 2-3-4. Factory/Service mode in Chapter 2 for menu operation in Factory mode.
3-43
CL-S700/CL-S703/CL-S700R
Factory SetupT
Init Fix-Thru
Exit
Enter X
4. Press the [STOP] (X) key to enter Init Fix-Thru sensitivity adjustment mode.
S
Init Fix-Thru T
No
Exit
Enter X
Init Fix-Thru T
Exec
Exit
Enter X
Now !! T
Executing
Exit
Enter X
CL-S700/CL-S703/CL-S700R
3-44
Finished T
DAC 123
Exit
Enter X
3-45
CL-S700/CL-S703/CL-S700R
Factory SetupT
Init Fix-Refl
Exit
Enter X
4. Press the [STOP] (X) key to enter Init Fix-Refl sensitivity adjustment mode.
S
Init Fix-Refl T
No
Exit
Enter X
Init Fix-Refl T
Exec
Exit
Enter X
CL-S700/CL-S703/CL-S700R
3-46
Now !! T
Executing
Exit
Enter X
Finished T
DAC 123
Exit
Enter X
3-47
CL-S700/CL-S703/CL-S700R
Factory SetupT
Init Adj-Thru
Exit
Enter X
4. Press the [STOP] (X) key to enter Init Adj-Thru sensitivity adjustment mode.
S
Init Adj-Thru T
No
Exit
Enter X
Init Adj-Thru T
Exec
Exit
Enter X
Now !! T
Executing
Exit
Enter X
CL-S700/CL-S703/CL-S700R
3-48
Finished T
DAC 123
Exit
Enter X
3-49
CL-S700/CL-S703/CL-S700R
Factory SetupT
Init Adj-Refl
Exit
Enter X
4. Press the [STOP] (X) key to enter Init Adj-Refl sensitivity adjustment mode.
S
Init Adj-Refl T
No
Exit
Enter X
Init Adj-Refl T
Exec
Exit
Enter X
CL-S700/CL-S703/CL-S700R
3-50
Now !! T
Executing
Exit
Enter X
Finished T
DAC 123
Exit
Enter X
3-51
CL-S700/CL-S703/CL-S700R
Motor Block
Spring Gauge
A
A
B
CL-S700/CL-S703/CL-S700R
3-52
TENSION
STANDARD
LOW
TENSION
STANDARD
LOW
SUPER LOW
3-53
CL-S700/CL-S703/CL-S700R
mm
mm
0
8
0
6
0m
15
CL-S700/CL-S703/CL-S700R
3-54
Adjustment procedure:
1. Remove the SA, Ope-Pane, SA, Front Right and SA, Front Center from the main body.
Refer to 3-5-8. Unit, Mechanism.
2. Open the head block by pushing the head open lever and remove the Unit, Head.
Refer to 3-5-1. Unit, Head.
3. Remove the Ribbon Cover of the Unit, Frame Ribbon L form the Unit, Mechanism.
Refer to 3-5-12. Unit, Frame Ribbon L.
4. Ribbon Tension Check/Adjustment on Take-up Side:
1) Set the Adjust screw for Take-up side ribbon tension adjustment to STANDARD
position.
2) Set the Ribbon-tension adjust ribbon (60mm) to the take-up side ribbon holder.
3) Hook a spring gauge of 500gf on the Ribbon-tension adjust ribbon and slowly pull the
ribbon end downward at a constant speed (approx. 7.5cm/sec. or so). Then, check if the
reading of the spring gauge in the steady state is within 450 +/- 50gf.
If the reading is in the specified range, no tension adjustment is required on take-up side.
Proceed to step 5 Ribbon Tension Check/Adjustment on Supply Side.
If not, proceed to the next sub step.
[Take-up side adjustment]
Adjust screw "A" (For Service)
When weak
When stronge
TENSION
STANDARD
LOW
N
RD
450 +/ 50gf
3-55
CL-S700/CL-S703/CL-S700R
4) Detach the Ribbon-tension adjust ribbon (60mm) once and then remove the Ribbon
Tension Spring Block from the Unit, Frame Ribbon L by removing the screw B.
After that, reset the Ribbon-tension adjust ribbon (60mm).
(Ribbon Tension Spring Block)
5) With the spring gauge of 500gf hooked on the Ribbon-tension adjust ribbon, repeat
above sub step 3) and be sure that the reading of the spring gauge is within 450 +/- 50gf.
If the reading is in the specified range, proceed to sub step 9).
If not, proceed to the next sub step.
6) Refer to the figure in sub step 3) and apply ThreeBond 1401B to the Adjust screw A after
removing it. Then, loosely tighten the Adjust screw A with a hex wrench and leave the
hex wrench on the Adjust screw A.
7) While repeating above sub step 3), adjust the position of Adjust screw A by moving hex
wrench up and down so that the reading of spring gauge is within 450 +/- 50gf.
Note: If tension is weak, move the Adjust screw A upward. If it is strong, move the Adjust
screw A downward.
8) After completion of adjustment, tighten the Adjust screw A.
9) Loosen (do not remove) the two screws C of the Ribbon Tension Spring Block to set the
Ribbon Tension Spring free.
(Ribbon Tension Spring Block)
CL-S700/CL-S703/CL-S700R
3-56
10) Hook a weight of 450g on the Ribbon-tension spring adjust ribbon (80mm).
The Front Belt Plate moves and stops at a certain position where it balances with the
weight.
Plate, Front Belt
Ribbon-tension spring
adjust ribbon (80mm)
450g
11) Mount the Ribbon Tension Spring Block and set the Ribbon Tension Spring so that no gap
is found between the Front Belt Plate. Then, apply ThreeBond 1401B to the screws C
and tighten the screws C.
Notes: Do not move the Front Belt Plate.
When tightening the screws C, pay special attention so as not to turn the
Ribbon Tension Spring.
Be sure that the Ribbon Tension Spring is fully contact with the Front Belt Plate.
Ribbon Tension Spring
3-57
CL-S700/CL-S703/CL-S700R
12) Remove the Ribbon-tension spring adjust ribbon (80mm) and reset the Ribbon-tension
adjust ribbon (60mm).
13) Hook a spring gauge of 500gf on the Ribbon-tension adjust ribbon (60mm) and slowly
pull the ribbon end downward at a constant speed (approx. 7.5cm/sec. or so). Then, check
if the reading of the spring gauge in the steady state is within 450 +/- 50gf.
If the reading is out of the specified range, repeat above sub steps 4) through 11).
5. Ribbon Tension Check/Adjustment on Supply Side:
1) Set the Adjust screw for Supply side ribbon tension adjustment to STANDARD position.
2) Set the Ribbon-tension adjust ribbon (60mm) to the supply side ribbon holder.
3) Hook a spring gauge of 500gf on the Ribbon-tension adjust ribbon and horizontally pull
the ribbon end toward you at a constant speed (approx. 7.5cm/sec. or so).
When the ribbon is drawn approx. more than 20cm, suddenly load applies to the spring
gauge. With this load condition, check if the reading of the spring gauge is within 400 +/50gf.
[Supply side adjustment]
Adjust screw "D"
(For Service)
When strong
TENSION
STANDARD
When weak
LOW
SUPER LOW
4) If the reading is in the specified range, no tension adjustment on supply side is required. In
this case, proceed to step 6. If not, proceed to the next sub step.
5) Apply ThreeBond 1401B to the Adjust screw D after removing it. Then, loosely tighten the
Adjust screw D with a hex wrench and leave the hex wrench on the Adjust screw D.
6) While repeating above sub step 3), adjust the position of Adjust screw D by moving hex
wrench up and down so that the reading of spring gauge is within 400 +/- 50gf.
CL-S700/CL-S703/CL-S700R
3-58
Note: If tension is weak, move the Adjust screw D downward. If it is strong, move the
Adjust screw D upward.
7) Tighten the Adjust screw D.
6. Repeat steps 1 to 3 in the reverse order to assemble the removed parts.
3-59
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
CHAPTER 4
TROUBLESHOOTING
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
Chapter 4 Troubleshooting
Table of Contents
4-1. Error Message and Corrective Actions ........................................................................... 4-3
4-2. Troubleshooting .............................................................................................................. 4-5
4-2-1. Problems in Powering Up the Printer ................................................................. 4-5
4-2-2. Media-feed Problems ......................................................................................... 4-6
4-2-3. Problems in Printing ........................................................................................... 4-7
4-2-4. Ribbon-feed Problem ......................................................................................... 4-8
4-2-5. Sensor Problems................................................................................................ 4-9
4-2-6. Operation Panel Problems ................................................................................. 4-13
4-2-7. Rewinder Problems (CL-S700R Only) ............................................................... 4-14
(1) Rewinding problem (CL-S700R Only) ....................................................... 4-14
(2) Rewinder sensor problem (CL-S700R Only) ............................................. 4-15
4-2-7. Connector Location .............................................................................................. 4-16
CL-S700/CL-S703/CL-S700R
4-2
Chapter 4 Troubleshooting
4-1. Error Message and Corrective Actions
ERROR LED
Flashing
LCD
Alarm
Head Hot
Flashing
Error
Head Cold
Flashing
Alarm
PFMotor Hot
Flashing
Error
Fan Lock
Flashing
Alarm
Cutter Hot
Flashing
Error
Head Open
Error
Paper End
Error
Paper Load
Flashing
Flashing
(to be continued)
Incorrect sensor adjustment against media to be
used:
Enter sensor adjustment mode
While pressing [MENU], [FEED] and [STOP]
4-3
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-1. Error Message and Corrective Actions
Causes/Corrective Actions
keys, turn on the power, and then perform
sensor adjustment.
For details, refer to 2-3-4 (3) How to change the
settings in Factory mode in Chapter 2.
Paper jam
Remove the jammed media.
Head low resistance value abnormality
Due to defective thermal element:
Printing quality will degrade.
Ribbon end
Install a new ribbon.
Communication error
Receiving buffer overrun error
Communication error
Parity error
Communication error
Framing error
Cover open
Close the printer cover.
Auto-cutter abnormality (foreign object etc.)
Jamming, etc.
Rewinder cover open (CL-S700R only)
Close the rewinder cover.
Rewinder full (CL-S700R only)
Remove the wound media from the rewinder
flange.
Rewinder failure (CL-S700R only)
Does not rewind, etc.
Rewinder motor temperature abnormality
(CL-S700R only)
Rewinding stops temporarily. Wait until the
motor gets cool.
CL-S700/CL-S703/CL-S700R
4-4
ERROR LED
LCD
Flashing
Error
Paper Jam
Alarm
Head Check
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Error
Ribbon End
Error
Serial Over Run
Error
Serial Parity
Error
Serial Framing
Error
Cover Open
Error
Cutter Fail
Error
Rewind Open
Error
Rewind Full
Error
Rewind Fail
Alarm
Rewinder Hot
Chapter 4 Troubleshooting
4-2. Troubleshooting
4-2. Troubleshooting
The following tables show possible remedies for various symptoms that might occur. Symptoms
are given in the left column, and the corresponding remedies in the right column.
Notes:
1. When parts are replaced, refer to Chapter 3 "Disassembly and Maintenance".
2. Connectors (J . . .) given in the column of checks and remedies are connected with the SA,
Main PCB. For the location of each connector, refer to 4-2-7. Connector Location".
Checks
Remedies
1. Connect it firmly.
4. Connect it firmly.
5. Connect it firmly.
6. Connect it firmly.
4-5
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
Media jamming
Checks
Remedies
1. Connect it firmly.
2. Connect it firmly.
3. Connect it firmly.
1. Connect it firmly.
CL-S700/CL-S703/CL-S700R
4-6
Chapter 4 Troubleshooting
4-2. Troubleshooting
Poor printing
Checks
Remedies
4. Connect it firmly.
5. Connect it firmly.
6. Connect it firmly.
4-7
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
Symptoms
Uneven print density
Checks
Remedies
Checks
Remedies
TENSION
STANDARD
LOW
TENSION
STANDARD
LOW
SUPER LOW
Ribbon wrinkles
occur.
(continued)
CL-S700/CL-S703/CL-S700R
4-8
Chapter 4 Troubleshooting
4-2. Troubleshooting
Symptoms
Ribbon wrinkles
occur.
Checks
Remedies
Printing continues
even when ribbon
runs out.
Ribbon slants.
Checks
Remedies
1. Connect it firmly.
1. Connect it firmly.
4-9
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
Symptoms
Ribbon end is not
correctly detected.
Label on liner or
notch of tag is not
detected.
(Transparent sensor
problem)
Or
Paper end is not
detected.
Checks
Remedies
1. Connect it firmly.
4. Connect it firmly.
5. Connect it firmly.
8. Failure in the Transparent Sensor or the 8. Replace the SA, Sensor U or the
SA, Sensor Bottom.
Reflective Sensor.
9. Failure in the control circuit.
CL-S700/CL-S703/CL-S700R
4-10
Chapter 4 Troubleshooting
4-2. Troubleshooting
4-11
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
Symptoms
Black mark on tag is
not detected.
(Reflective sensor
problem)
Or
Paper end is not
detected.
Checks
Remedies
1. Set it to Reflect.
4. Connect it firmly.
CL-S700/CL-S703/CL-S700R
4-12
Chapter 4 Troubleshooting
4-2. Troubleshooting
No key works.
Nothing appears on
the LCD.
Checks
Remedies
1. Connect it firmly.
1. Connect it firmly.
1. Connect it firmly.
3. Connect it firmly.
4-13
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
Checks
Remedies
5. Connect it firmly.
6. Connect it firmly.
1. Connect it firmly.
CL-S700/CL-S703/CL-S700R
4-14
Chapter 4 Troubleshooting
4-2. Troubleshooting
Checks
Remedies
Rewinder cover is
closed, but rewinder
cover open status is
detected.
(LCD shows Error
Rewinder Open.)
Rewinder motor
rotation is not
detected.
(LCD shows Error
Rewinder Fail.)
4-15
CL-S700/CL-S703/CL-S700R
Chapter 4 Troubleshooting
4-2. Troubleshooting
J7 J6
J9
J8
J16
J22 J21
Adjustable Sensor
(Reflective sensor)
J12
J11
SA, Fan
10
J14
J5
J3
J15
J4
Unit, Head
(Blue Tape)
CN101
CL-S700/CL-S703/CL-S700R
4-16
Chapter 4 Troubleshooting
4-2. Troubleshooting
J503
J504
PS501 PS502
J502
4-17
CL-S700/CL-S703/CL-S700R
CHAPTER 5
PARTS LISTS
Note:
The Parts Lists section consists of the following two parts:
Former half: For CL-S700 and CL-S703
Latter half:
For CL-S700R (Common parts with the printer upper area are to be
referred to the former half.)
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703
5-2
CL-S700/CL-S703
Recommended Spare Parts List
Revision Up List
Sheet No. Rev. No.
1/1
5-3
Date
Dec. 15, 2010
CL-S700/CL-S703
Location
Part No.
Part Name
Maint. Class
Worn
Casual
1-15
JN66801-0
2-8-1
JN09802-0
Unit, Head
For CL-S700/CL-S700R
(Rev. No.1)
2-8-2
JN09804-0
8-9
JN48704-0
SA, Sensor U
Adjustable type
8-24
JN48705-0
Adjustable type
9-1
JN28801-0
9-39
JN25801-0
Unit, Motor
9-7
JN48701-0
SA, Sensor U
Fixed type
9-18
JN48702-0
Fixed type
10
14-2-1
JN66701-0
11
14-2-2
JN66702-0
12
14-2-3
JN66718-0
For CL-S700R
(Rev. No.1)
13
14
15
16
17
18
CL-S700/CL-S703
5-4
CL-S700/CL-S703
Drawing No. 1
Parts List & Location for General Assembly
Revision Up List
Sheet No. Rev. No.
5-5
Date
1/3
2/3
3/3
CL-S700/CL-S703
DRAWING NO. 1
5-6
CL-S700/CL-S703
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
1-1
Roll Holder
JE99090-0
1-2
JM79201-0
1-3
1-4
----
Cover, Hinge
JN56209-0
1-5
JN56116-0
1-6
JN56704-0
1-7
JM34710-1
1-8
Stopper, Hinge
JN54103-0
1-9
SA, Hinge
JN59905-0
1-10
Unit, Mechanism
JN99801-0
1-11
JN56112-0
1-12
Unit, PCB
1-13
JN54910-0
1-14
Plate, Power
JN64101-0
1-15
JN66801-0
1-16
Cover, Cable
JN56201-0
1-17
JN67706-0
1-18
JN67901-0
1-19
JN59903-0
1-20
SA, Fan
JN65901-0
5-7
Remarks
24600730
Ref: Drawing No. 10
CL-S700/CL-S703
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
Remarks
1-21
JN67709-0
1-22
Rail, Guide U
JN54906-0
1-23
JN54907-0
1-24
JN54202-0
1-25
Sheet, Case L
JN54106-0
1-26
SA, Ope-pane
JN56705-0
1-27
JN56708-0
1-28
JN56707-0
1-29
SA, Case L
JN56701-1
1-30
Leg, Case
JN56901-0
1-31
JN56113-0
1-32
JN56115-0
1-33
JN56117-0
1-34
JN56110-0
1-35
JN56713-0
1-36
E00230-060F
1-37
E00530-050F
19
1-38
E04030-050F
15
1-39
E00530-050KF
13
1-40
E00940-300F
CL-S700/CL-S703
5-8
Including Inlet
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
1-41
E00230-060F
1-42
E00130-120F
1-43
E00540-040WF
1-44
E50740-000WF
5-9
Remarks
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 2
Parts List & Location for Unit, Mechanism
Revision Up List
Sheet No. Rev. No.
CL-S700/CL-S703
5-10
Date
1/2
2/2
DRAWING NO. 2
2-22
2-19
2-22
2-20
2-21
2-1
(DRW NO.3)
2-6
(DRW NO.4)
2-4
2-22
2-2
2-3
2-25
2-22
2-7
2-23
2-8-1
2-8-2
2-22
2-5
(DRW NO.5)
(DRW NO.6)
2-22
2-9
(DRW NO.7)
2-22
2-14
2-15
2-24
2-13
2-16
2-17
2-10
2-22
2-11
2-22
(DRW NO.8)
2-12
2-22
2-18
(DRW NO.9)
5-11
CL-S700/CL-S703
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 2
Q'ty/
Unit
Remarks
2-1
Bushing
JE99704-0
2-2
JN32001-0
2-3
Bushing
JE99705-0
24400680
2-4
JN34704-0
2-5
JN44803-0
2-6
Unit, Frame U
JN44802-0
2-7
Spring, Head Up
JN13601-0
2-8-1
Unit, Head
JN09802-0
2-8-2
JN09804-0
2-9
JN34703-0
2-10
JN44712-0
2-11
Ground Brush
JE99438-0
33000340
2-12
JN44804-0
2-13
JN54911-0
2-14
Damper
JE99051-0
25200890
2-15
Damper Pin
JE99023-0
22601801
2-16
SA, Head Up SW
JN68704-0
2-17
JN59902-0
2-18
Unit, Frame
----
2-19
JN34801-0
(Rev. No. 1)
CL-S700/CL-S703
5-12
24400670
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 1
Q'ty/
Unit
2-20
Cover, Ribbon
JN36201-0
2-21
Screw, PH , M3.0x6
E00130-060F
2-22
E04030-050F
11
2-23
E00230-060F
2-24
E00140-060F
2-25
JN33602-0
5-13
Remarks
(Rev. No. 1)
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 3
Parts List & Location for Unit, Frame U
Revision Up List
Sheet No. Rev. No.
CL-S700/CL-S703
5-14
Date
1/2
2/2
3-22
3-3
3-29
3-4
3-1
3-1
3-2
3-23
3-21
3-5
Apply lubricant to
other side also.
3-7
3-30
3-31-1
3-31-2
3-8
3-27 3-26
3-10
3-11
3-18 3-19
3-20
3-9
3-16
3-24
3-14
3-6
3-25
3-28
3-32
3-17
3-15
3-12
3-13
5-15
CL-S700/CL-S703
Drawing No. 3
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
Remarks
3-1
JE99683-0
23205720
3-2
JE99684-0
23205730
3-3
JE99651-0
21903240
3-4
JN29715-0
3-5
SA, Frame U
JN44706-0
3-6
JN67707-0
3-7
Wire Tie
C6701-101#
3-8
Spring, Head L
JN13603-0
3-9
JE99434-0
3-10
JN54908-0
3-11
JE99117-0
20803381
3-12
Head Plate
JE99011-0
20803370
3-13
Offset Spring
JE99016-0
21902562
3-14
Slider
JE99048-0
25200861
3-15
Spring, Head R
JN13602-0
3-16
Curved Washer
JE99065-0
90500390
3-17
Adjust Screw
JE99192-0
92100202
3-18
JE99019-0
21902601
3-19
Lever, Head Up
JN14201-0
3-20
Polyslider Washer
JE99064-0
CL-S700/CL-S703
5-16
25201200
90500380
Location
Part No.
Part Name
Q'ty/
Unit
3-21
Nyrock Screw
JE99066-0
3-22
Polyslider 1
JN39902-0
3-23
E-Ring, 3.0
E60330-000F
3-24
E-Ring, 2.0
E60320-000F
3-25
Nut, M3
E40130-000F
3-26
E00540-040WF
3-27
E50740-000WF
3-28
E04230-080F
3-29
Polyslider
JN39901-0
3-30
AH90935-0
English
3-31-1
AR99902-0
3-31-2
AR99901-0
3-32
JN67712-0
5-17
92100220
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 4
Parts List & Location for SA, Front Tension Arm
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700/CL-S703
5-18
Date
Apr. 18, 2008
DRAWING NO. 4
4-1
4-2
4-3
4-6
5-19
4-5
4-4
CL-S700/CL-S703
Drawing No. 4
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
4-1
JN34701-0
4-2
Bushing
JE99705-0
4-3
JN32002-0
4-4
Bushing
JE99704-0
4-5
JN33601-0
4-6
JN34107-0
CL-S700/CL-S703
5-20
Remarks
24400680
24400670
CL-S700/CL-S703
Drawing No. 5
Parts List & Location for Unit, Frame Rear
Revision Up List
Sheet No. Rev. No.
1/1
5-21
Date
Apr. 18, 2008
CL-S700/CL-S703
5-1
5-2
5-4
5-3
5-12
5-5
5-7
5-6
5-3
5-11
5-8
5-3
5-3
5-9
5-10
5-8
5-3
CL-S700/CL-S703
5-22
5-12
Location
Part No.
Part Name
Q'ty/
Unit
Remarks
5-1
Bushing
JE99704-0
24400670
5-2
JE99710-0
25100710
5-3
Bushing
JE99705-0
24400680
5-4
JN44705-0
5-5
JE99650-0
5-6
JN44708-0
5-7
Side Plate L
JE99639-0
20804850
5-8
JE99709-0
25100690
5-9
Beam
JE99667-0
23000680
5-10
Side Plate R
JE99640-0
20804860
5-11
E04030-050F
5-12
E00230-060F
5-23
21903231
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 6
Parts List & Location for SA, Frame Ribbon R
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700/CL-S703
5-24
Date
Apr. 18, 2008
DRAWING NO. 6
6-1
6-2
6-4
6-3
5-25
CL-S700/CL-S703
Drawing No. 6
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
6-1
JN34201-0
6-2
JN34202-0
6-3
Frame, Ribbon R
JN34104-0
6-4
JN36202-0
CL-S700/CL-S703
5-26
Remarks
CL-S700/CL-S703
Drawing No. 7
Parts List & Location for SA, Base Guide Open
Revision Up List
Sheet No. Rev. No.
1/1
5-27
Date
Apr. 18, 2008
CL-S700/CL-S703
DRAWING NO. 7
7-3
7-4
7-8
7-1
7-6
7-5
7-7
7-2
7-8
7-1
CL-S700/CL-S703
5-28
Drawing No. 7
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
7-1
JN29703-0
7-2
Frame, Damper
JN24105-0
7-3
E-Ring, 4.0
E60340-000F
7-4
Shaft, Damper
JN22005-0
7-5
Frame, Damper
JN24203-0
7-6
Spring, Damper L
JN23603-0
7-7
Spring, Damper R
JN23602-0
7-8
E04030-050F
5-29
Remarks
Metal
Plastic
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 8
Parts List & Location for Unit, Sensor Adjust
Revision Up List
Sheet No. Rev. No.
CL-S700/CL-S703
5-30
Date
1/2
2/2
DRAWING NO. 8
8-1
8-2
8-4
8-26
8-3
8-6
8-27
8-7
8-8
8-5
8-10
8-28
8-9
8-28
8-4
8-12
8-13
8-3
8-11
8-14
8-32
8-30
8-15
8-3
8-20
8-26
8-16
8-28
8-21
8-29
8-29
8-26
8-18
8-17
8-22
8-31
8-10
8-23
8-24
8-8
8-7
8-26
8-27
8-25
5-31
CL-S700/CL-S703
Drawing No. 8
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
Remarks
8-1
JE99179-0
8-2
JN24208-0
8-3
E70412-080F
8-4
Screw Gear
JE99279-0
8-5
JN22004-0
8-6
Position Label
JE99281-0
71104631
8-7
Stopper Plate
JE99275-0
20803640
8-8
Move Pin
JA99067-0
22601080
8-9
SA, Sensor U
JN48704-0
Adjustable type
8-10
Wire Tie
C6701-101#
8-11
JN29702-0
8-12
JN24228-0
8-13
JE99132-0
21902730
8-14
JE99228-0
24600781
8-15
JN54909-0
8-16
JN22001-0
8-17
JN23601-0
8-18
JN22201-0
8-19
Ratchet Gear
JE99280-0
8-20
JN24201-0
CL-S700/CL-S703
5-32
71104522
24001020
24001030
Drawing No. 8
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
8-21
Cover, RFID
JN24204-0
8-22
JN29705-0
8-23
JN22006-0
8-24
JN48705-0
8-25
Holder, Sensor L
JN24101-0
8-26
E-Ring, 3.0
E60330-000F
8-27
E13220-040F
8-28
E-Ring, 2.0
E60320-000F
8-29
E04030-050F
8-30
E00130-030F
8-31
Ratchet Spring
JE99276-0
8-32
JN24901-0
5-33
Remarks
Adjustable type
21902760
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 9
Parts List & Location for Unit, Frame
Revision Up List
Sheet No. Rev. No.
CL-S700/CL-S703
5-34
Date
1/3
2/3
2/3
DRAWING NO. 9
9-40 9-39
9-1
9-30
9-2
9-5
9-31
9-3
9-4
9-38-1
9-38-2
9-33
9-7
9-32
9-34
9-31
9-32
9-33
9-33
9-6
9-8
9-35
9-9
9-10
9-11
9-29
9-16
9-12
9-15
9-13
9-18
9-19
9-27
9-26
9-36
9-17
9-14
9-33
9-23
9-24
9-20
9-37
9-28 9-36
9-25
9-14
9-33
9-33
9-21
9-22
5-35
CL-S700/CL-S703
Drawing No. 9
Location
Part Name
Part No.
Rev. No. 1
Q'ty/
Unit
Remarks
9-1
JN28801-1
9-2
JN26902-0
9-3
----
9-4
JN24109-0
9-5
Flange, Motor
----
9-6
Bracket, Motor
JN24108-0
9-7
SA, Sensor U
JN48701-0
Fixed type
9-8
Paper Guide
JE99045-0
24600660
9-9
Cover, Pulley
JN24207-0
9-10
SA, Frame
JN44701-0
9-11
Plate, Peel
JN24107-0
9-12
JN26901-0
9-13
SA 1, Drive Shaft
JN22702-0
9-14
JN21901-0
9-15
JE99446-0
23204211
9-16
Friction Cork
JE99037-0
24000910
9-17
JE99017-0
21902571
9-18
JN48702-0
Fixed type
9-19
JN44707-0
9-20
JN66725-0
CL-S700/CL-S703
5-36
(Rev. No.1)
Not supplied
Not supplied
Drawing No. 9
Location
Part Name
Part No.
Rev. No. 1
Q'ty/
Unit
Remarks
9-21
JN67715-0
9-22
JN67716-0
9-23
JN22011-0
9-24
JN20302-0
9-25
E30130-050F
9-26
Tension Pulley
JE99154-0
2400090
9-27
Tensioner Pin
JE99136-0
22601891
9-28
Plate, Tension
JN24110-0
9-29
Tension Spring
JE99131-0
9-30
JN67705-0
9-31
E00130-060F
9-32
E04030-050F
9-33
E04030-060F
10
9-34
E00530-050KF
9-35
E13220-080F
9-36
E-Ring, 3.0
E60330-000F
9-37
E-Ring, 2.0
E60320-000F
9-38-1
Unit, Motor
JN25801-0
9-38-2
Unit, Motor
JN25803-0
9-39
Gear, One-way
JN20201-0
(Rev. No.1)
5-37
21902722
CL-S700/CL-S703
Drawing No. 9
Location
9-40
Part Name
E-Ring, 4.0
CL-S700/CL-S703
Part No.
E60340-000F
5-38
Rev. No. 1
Q'ty/
Unit
1
Remarks
(Rev. No.1)
CL-S700/CL-S703
Drawing No. 10
Parts List & Location for Unit, Top Cover
Revision Up List
Sheet No. Rev. No.
1/1
5-39
Date
Apr. 18, 2008
CL-S700/CL-S703
DRAWING NO. 10
10-1
10-2
10-7
10-6
10-6
10-7
10-3
10-5
10-4
CL-S700/CL-S703
5-40
Drawing No. 10
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
10-1
JN56710-1
10-2
JN56207-0
10-3
Logo, CITIZEN
JN54201-0
10-4
JN56208-0
10-5
Cover, Window
JN54101-0
10-6
E10130-060F
10-7
JN56114-0
5-41
Remarks
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 11
Parts List & Location for SA, Ope-pane
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700/CL-S703
5-42
Date
Jan. 15, 2009
11-5
11-10
11-4
11-2
11-1
11-3
11-11
11-11
11-12
11-6 11-7
11-12
11-8 11-9
5-43
CL-S700/CL-S703
Drawing No. 11
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
11-1
Sheet, Ope-Pane
JN54901-0
11-2
Cover, Ope-Pane
JN56202-0
11-3
JN68705-0
11-4
JN66704-0
11-5
JN56706-0
11-6
Switch, Pause
JN56212-0
11-7
Switch, Feed
JN56211-0
11-8
Switch, Menu
JN56210-0
11-9
Switch, Stop
JN56213-0
11-10
Cover, LCD
JN54102-0
11-11
E10130-060F
11-12
E00530-050F
CL-S700/CL-S703
5-44
Remarks
CL-S700/CL-S703
Drawing No. 12
Parts List & Location for SA, Front Center
Revision Up List
Sheet No. Rev. No.
1/1
5-45
Date
Apr. 18, 2008
CL-S700/CL-S703
DRAWING NO. 12
12-4
12-3
12-4
12-2
12-1
CL-S700/CL-S703
5-46
Drawing No. 12
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
12-1
JN56204-0
12-2
JN56121-0
12-3
Cover, Front
JN56205-0
12-4
E10130-060F
5-47
Remarks
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. 13
Parts List & Location for SA, Front Right
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700/CL-S703
5-48
Date
Apr. 18, 2008
DRAWING NO. 13
13-2
13-3
13-1
5-49
CL-S700/CL-S703
Drawing No. 13
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
13-1
JN56203-0
13-2
JN56120-0
13-3
E10130-060F
CL-S700/CL-S703
5-50
Remarks
CL-S700/CL-S703
Drawing No. 14
Parts List & Location for Unit, PCB
Revision Up List
Sheet No. Rev. No.
1/1
5-51
Date
Dec. 15, 2010
CL-S700/CL-S703
DRAWING NO. 14
14-4
14-3
14-1
14-2-1
14-2-2
14-2-3
14-5
14-6
CL-S700/CL-S703
14-7
5-52
Drawing No. 14
Location
Part Name
Part No.
Rev. No. 1
Q'ty/
Unit
Remarks
14-1
JN67708-0
14-2-1
JN66701-0
14-2-2
JN66702-0
14-2-3
JN66718-0
14-3
JN56711-0
14-4
JM66825-1
14-5
C6390-054#
14-6
E04030-050F
14-7
E00530-050F
5-53
CL-S700/CL-S703
CL-S700/CL-S703
Drawing No. Parts List & Location for Accessories
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700/CL-S703
5-54
Date
Apr. 18, 2008
TITLE: Accessories
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
Remarks
C6009-000#
For CSA
C6009-200#
For CSE
C6009-300#
For CSE
JN749**
JN749**
Head, Cleaner
JM79904-0
JN79901-0
JM79907-0
JM39901-0
JM39902-0
5-55
For CSA
CL-S700/CL-S703
5-55
CL-S700R
CL-S700R
Recommended Spare Parts List
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700R
5-56
Date
Apr. 18, 2008
Location
Part No.
Q'ty/
Unit
Part Name
Maint. Class
Worn
Casual
Remarks
Dedicated for
CL-S700R
1-15
JN66801-0
2-13
JN09802-0
Unit, Head
8-9
JN48704-0
SA, Sensor U
Adjustable type
8-24
JN48705-0
Adjustable type
9-1
JN28801-0
9-39
JN25803-0
Unit, Motor
9-7
JN48701-0
SA, Sensor U
Fixed type
9-18
JN48702-0
Fixed type
14-2
JN66718-0
10
11
12
13
14
15
16
17
18
19
20
5-57
CL-S700R
CL-S700R
Drawing No. 1
Parts List & Location for General Assembly
Revision Up List
Sheet No. Rev. No.
CL-S700R
5-58
Date
1/3
2/3
3/3
5-59
CL-S700R
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
1-1
Roll Holder
JE99090-0
1-2
JM79201-0
1-3
1-4
----
Cover, Hinge
JN56209-0
1-5
JN56116-0
1-6
JN56704-0
1-7
JM34710-1
1-8
Stopper, Hinge
JN54103-0
1-9
SA, Hinge
JN59905-0
1-10
Unit, Mechanism
JN99801-0
1-11
JN56112-0
1-12
Unit, PCB
1-13
JN54910-0
1-14
Plate, Power
JN64101-0
1-15
JN66801-0
1-16
Cover, Cable
JN56201-0
1-17
JN67706-0
1-18
JN67901-0
1-19
JN59903-0
1-20
SA, Fan
JN65901-0
CL-S700R
5-60
Remarks
24600730
Ref: Drawing No. 10 / CL-S700, S703
Dedicated for
CL-S700R
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
1-21
JN67709-0
1-22
Rail, Guide U
JN54906-0
1-23
JN54907-0
1-24
JN54202-0
1-25
1-26
SA, Ope-pane
JN56705-0
1-27
1-28
JN56707-0
1-29
SA, Case L
JN56701-1
1-30
1-31
JN56113-0
1-32
JN56115-0
1-33
JN56117-0
1-34
JN56110-0
1-35
JN56713-0
1-36
E00230-060F
1-37
E00530-050F
19
1-38
E04030-050F
15
1-39
E00530-050KF
11
1-40
E00940-300F
5-61
Remarks
Dedicated for
CL-S700R
Including Inlet
CL-S700R
Drawing No. 1
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
Remarks
Dedicated for
CL-S700R
1-41
E00230-060F
1-42
E00130-120F
1-43
E00540-040WF
1-44
E50740-000WF
1-45
SA2, Peeler
JN29713-0
1-46
JN99907-0
1-47
Cushion, Damper
JN24143-0
1-48
Sheet, Damper
JN24142-0
1-49
E04030-050F
1-50
E00530-050F
CL-S700R
5-62
CL-S700R
Drawing No. 2
Parts List & Location for Unit, Rewinder
Revision Up List
Sheet No. Rev. No.
5-63
Date
1/4
2/4
3/4
4/4
DRAWING NO. 2
2-4
2-2
2-1
2-3
2-61
(DRW NO.3)
2-20
2-5
2-64
2-61
2-6
2-19
2-8
2-9
2-7
2-10
2-21
2-22
2-66
2-35
2-64
2-30
2-32
2-63
2-63
2-15
2-66
2-64
2-23
2-61 2-66
2-64
2-17
2-6
2-18
2-22
2-24
2-63
2-31
2-64
2-64
2-37
2-63
2-65
2-64
2-34 2-61
2-36
2-64
2-14
2-16
2-12
2-33
2-11
2-63
2-64
2-61
2-64
2-25
2-26
2-63
2-67
2-61
2-27
2-38
2-64
2-63
2-63
2-63
2-66
2-28
2-66
2-40
2-39
2-61
2-59
2-43
2-66
2-41
2-13
2-44
2-51
2-63
2-61
2-58
2-64
2-64 2-35
2-64
2-39
2-47
2-29
2-42
2-45 2-46
2-57
2-66
2-59
2-66
2-64
2-48
2-52
2-55
2-64
2-63
2-49
2-50
2-53
2-63
2-56
2-54
2-56
CL-S700R
2-63
5-64
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
2-1
JN22018-0
2-2
JN23609-0
2-3
JN23610-0
2-4
JN24120-0
2-5
JN24121-0
2-6
Shaft, Damper
JN22012-0
2-7
JN24225-0
2-8
JN29710-0
2-9
JN22017-0
2-10
JN24223-0
2-11
JN23608-0
2-12
JN24145-0
2-13
JN24144-0
2-14
JN24226-0
2-15
SA, Interlock SW
JN68710-0
2-16
Plate, Nut
JN24138-0
2-17
JN24227-0
2-18
JN44110-0
2-19
JN29708-0
2-20
SA1, Peeler
JN29706-0
5-65
Remarks
CL-S700R
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
2-21
JN22015-0
2-22
Roller, Damper
JN24216-0
2-23
JN23604-0
2-24
JN22014-0
2-25
JN23605-0
2-26
Plate, Damper
JN24114-0
2-27
Spring, Handle R
JN23606-0
2-28
Plate, Handle
JN24115-0
2-29
JN56716-0
2-30
JN56135-0
2-31
JN56134-0
2-32
JN24210-0
2-33
Frame, Door L
JN56132-0
2-34
Plate, Rewinder SW
JN24213-0
2-35
Stopper Rewinder
JN24211-0
2-36
JN24124-0
2-37
Torque Limiter
JN29903-0
2-38
JN24126-0
2-39
Ring, Damper
JN24212-0
2-40
Shaft, Door
JN22020-0
CL-S700R
5-66
Remarks
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
2-41
E70120-120F
2-42
JN24209-0
2-43
Frame, Door R
JN56133-0
2-44
JN24127-0
2-45
JN56215-0
2-46
JN56723-0
2-47
Sheet, Anti-Adhere
JN54107-0
2-48
Cover Rewinder
JN24215-0
2-49
Handle
JN24217-0
2-50
Door, Rewinder
JN56214-0
2-51
Shaft, Handle
JN22016-0
2-52
JN24116-0
2-53
JN56725-0
2-54
JN56216-0
2-55
JN56718-0
2-56
Leg, Case
JN56901-0
2-57
JN59904-0
2-58
JN24125-0
2-59
JN66705-0
2-60
SA, RW Cable
JN67721-0
5-67
Remarks
CL-S700R
Drawing No. 2
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
2-61
E-Ring, 3.0
E60330-000F
11
2-62
E04030-060F
2-63
E10130-060F
22
2-64
E04030-050F
24
2-65
E00620-100F
2-66
E-Ring, 4.0
E60340-000F
11
2-67
E04030-040F
CL-S700R
5-68
Remarks
CL-S700R
Drawing No. 3
Parts List & Location for SA1, Peeler
Revision Up List
Sheet No. Rev. No.
1/1
5-69
Date
Apr. 18, 2008
CL-S700R
DRAWING NO. 3
3-3
3-13
3-7
3-9
3-8
3-4
3-12
3-2
3-5
3-13
3-2
3-3
3-7
3-6
3-2
3-7
3-15
3-10
3-11
3-14
CL-S700R
5-70
Drawing No. 3
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
3-1
JN28502-0
3-2
Bush, Idle
JE99750-0
3-3
JE99325-0
3-4
Spring, L Friction
JE99761-0
3-5
Spring, R Friction
JE99760-0
3-6
Roller, Friction
JE99758-0
3-7
Bush, Friction
JE99762-0
3-8
JN24112-0
3-9
Plate1, Peeler
JN24111-0
3-10
JN24113-0
3-11
JE69149-2
3-12
E-Ring, 2.0
E60320-000F
3-13
E04030-050F
3-14
Screw,PH,M2.0x3
E00120-030WF
3-15
E00530-050F
5-71
Remarks
CL-S700R
CL-S700R
Drawing No. 4
Parts List & Location for SA2, Peeler
Revision Up List
Sheet No. Rev. No.
1/1
CL-S700R
5-72
Date
Apr. 18, 2008
DRAWING NO. 4
4-7
4-5
4-6
4-3
4-2
4-4
4-8
4-9
4-1
5-73
CL-S700R
Drawing No. 4
Location
Part Name
Part No.
Rev. No. 0
Q'ty/
Unit
4-1
Roll, Peel
JE99338-1
4-2
Plate2, Peeler
JN24123-0
4-3
JE99370-0
4-4
JE99366-0
4-5
JE99335-1
4-6
E00420-040WF
4-7
E00926-140F
4-8
JE99341-0
4-9
E-Ring, 4.0
E60340-000F
CL-S700R
5-74
Remarks
CHAPTER 6
CIRCUIT DIAGRAMS
CL-S700/CL-S703/CL-S700R
CL-S700/CL-S703/CL-S700R
6-2
UNIT, MOTOR
JN25801-**F
UNIT, HEAD
J4
J3
1
2
3
4
5
6
7
8
9
10
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
+5V
S.GND
P.GND
P.GND
P.GND
P.GND
+24V
+24V
+24V
+24V
J11
1
2
3
4
5
6
HEADCLK
HEADD1
HEADLAT
+3.3V
HDTMP
P.GND
P.GND
P.GND
P.GND
P.GND
+24V
+24V
+24V
+24V
+24V
1
2
3
1
2
1
2
3
4
1
2
UP LED A
UP LED K
1
2
3
4
1
2
J22
1
2
3
4
UP LED A
UP LED K
SA, HEAD UP
CABLE
JN66703-**F
J9
J8
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
LED A
LED K
TR C
TR E
J7
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
SA, HEAD UP SW
JN68704-**F
PHOTO INT
1
2
3
4
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
J21
1
2
3
4
UP LED A
UP LED K
IED
PHOTO TR
IED
1
2
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
LED A
LED K
TR C
TR E
1
2
3
4
1
2
HDUSENS
S.GND
FAN +
FAN FANLOCK
J12
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
+5V
S.GND
TXD1
RXD1
S.GND
S.GND
N.C.
N.C.
RFRUN
RFOSC
+5V
+3.3V
N.C.
S.GND
DACIN
DACCLK
CS_LCD
LCD_CD
LCD_LED4
LCD_LED3
LCD_LED2
J13
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
LCD_LED1
N.C.
N.C.
SW1
SW2
SW3
SW4
CV_OPN
N.C.
S.GND
S.GND
+24V
+24V
P.GND
P.GND
S.GND
DCMTR0
DCMTR1
HPSENS0
HPSENS1
MTTH
CPRTYP0
10
11
J14
RF-ID(OPTION)
SA,POWER
CABLE
JN67706-**F
SA,FAN
JN65901-**F
AC INPUT
+5V
+3.3V
N.C.
S.GND
DACIN
DACCLK
CS_LCD
LCD_CD
LCD_LED4
LCD_LED3
LCD_LED2
+24V
+24V
P.GND
P.GND
S.GND
DCMTR0
DCMTR1
HPSENS0
HPSENS1
MTTH
CPRTYP0
1
2
3
4
5
6
7
8
9
LCD_LED1
N.C.
N.C.
SW1
SW2
SW3
SW4
CV_OPN
N.C.
S.GND
S.GND
10
11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
xSTROBE
S.GND
DATA0
S.GND
DATA1
S.GND
DATA2
S.GND
DATA3
S.GND
DATA4
S.GND
DATA5
S.GND
DATA6
S.GND
DATA7
S.GND
xACKNLG
S.GND
J16
BUSY
S.GND
PE
S.GND
SLCT
xPRIME
xATFD-XT
xFAULT
N.C.
S.GND
IETYP0
IETYP1
N.C.
N.C.
+5V
xSLCT-IN
+5V
xRESET
N.C.
N.C.
1
2
3
4
5
6
7
8
9
10
11
12
13
F.GND
TXD
RXD
RTS
CTS
DSR
SGND
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
+5V
S.GND
MTREF
MTENC
OPN
PEELSENS
CPRTYP1
14
15
16
17
18
19
20
21
22
23
24
25
+5V
N.C.
N.C.
N.C.
N.C.
N.C.
DTR
N.C.
N.C.
N.C.
N.C.
N.C.
USBVCC
DM
DP
USBLGND
1
2
3
4
J18
SA,CENTRO
CABLE
JN67708-**F
J19
RS232C
USB1.1
CN101
J803
1
2
3
4
5
6
7
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
J17
SA,OPTION
CABLE 2
JN67716-**F
J801
12
13
14
15
16
17
18
19
20
21
22
+5V
S.GND
MTREF
MTENC
OPN
PEELSENS
CPRTYP1
SA,OPTION
CABLE 1
JN67715-**F
J401
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
7
J15
CABLE,OPEPANE FFC
JN67901-**F
AC/DC
CONVERTER
UNIT,POWER
SUPPLY
JN66801-**F
J6
VREF(+3V)
MOTTMP
J5
-A
BCOM
-B
A
ACOM
B
SA,CENTRONICS I/F
CON PCB JM66710-**F
CN102
+24V
+24V
+24V
+24V
P.GND
P.GND
P.GND
P.GND
HEADSTB
HEADD4
S.GND
HEADD3
+5V
HEADD2
HEADSTB
6
SA, ADJ SENS U
JN68701-**F
IED
PHOTO TR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
5
SA, FRONT SENS L
JN68708-**F
HOST
COMPUTER
IEEE1284
SA,CONNECT PCB
JN66725-**F
J802
J804
LED x8
SW x4
LCD
SA,OPEPANE PCB
JN66704-**F
A
AUTO
CUTTER
(OPTION)
PEELER
(OPTION)
Title
Size
A4
Number
6-3
Revision
JN66701-0/JN66702-0
Date:
File:
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
)
"
)
!
'
)
!
' "
)))
)
)
)
)
(
%&
%&
%&
%&
%&
(
(
(
(
' *
'
'
(%
'!
%&
%&
%&
%&
%&
(
(
(
(
(
"
"
)
" "
)
*
(
*
)
(
%&
,
,
%&
%&
%%
%%
)
)
(
(%
%%
%&
*
-
-
-
-
-
)
)
(
(%
%%
%&
*
-
-
-
-
-
)
)
)
)
)
"
))
)
"
%&
%&
+
!
+ ,
+
%%
%&
%%
%%
(
+
(
+
%%
%%
%%
%&
)
)
!-
-
!-!
!'
%&
!
-
)
(
%%
%%
%%
%%
%%
%%
%%
%%
%%
%%
"
!
"&
"%
"
'
!
*
)
"
)
%&
,
,
&
%%
%%
%%
%%
%%
%%
"
))
* "
))
' +
'
%&
" !)
(
%&
!
!
*
)
(
(
%&
%&
%&
!
!
'
'
!'
+
+
"
)
(
%&
!
!
-
%%
%%
-
%%
%&
%&
)
)
'
"
))
"
"
))
*
+
"
%&
%&
%&
%&
%&
%&
%&
%&
)
%&
+ *&
%&
'
)
*
*
"
))
(
(
%&
%&
%&
!
!
'
'
!'
# $
"
))
-
%%
%%
-
%%
%&
%&
"
))
)
*
'
*
"
))
*
'
"
))
#($
!!
!
"
)
!
" #$
)
"
"!
"
"
)
*
"
))
))
(
(
(
(
%&
%&
%&
%&
' "
'
%&
'
(
'
' "
!
'!
)
!
"
))
)
'
"
))
)
)
'
!
"
!))
'
!
./01
!
CL-S700/CL-S703/CL-S700R
6-4
!
.:1
;/1<
.01<
)
16.7.89
=11/ 8>
5;?9 "@<
5
T1
X1
165
1M
X2
U1A
R5
0
164
R4
*0
R1
X1
R3
*0
D
R10
0
R11
0
V3R3
T20
R21
SB V
4
3
G C
X2
FCXO-03L(48MHz)
15
15
2007/1/18
1
2
6,8,13
-GRESET
2007/1/18
2007/1/18
2007/1/18
2007/1/18
2007/1/18
V3R3
R30
22k
11
14
14
11
15
R31
22k
T25
T27
T29
155
154
153
T33
T35
T37
T39
T41
152
149
148
147
146
145
T45
T47
T49
T51
T53
T55
25
24
23
22
21
20
T58
T60
T61
19
18
17
T65
T67
T69
T71
T73
T75
176
175
174
173
172
171
T79
T81
T83
T85
T86
T88
34
33
32
31
30
29
T93
T95
T97
T99
T101
T103
T104
T106
5
6
7
8
9
10
11
12
ANI0
ANI1
ANI2
ANI3
ANI4
ANI5
ANI6
ANI7
T112
4
13
AVREFP
AVREFM
UBINTP
PLDRXDO
TXD0
11
11
3,11
6
3,11
RXD1
TXD1
DACCLK
CNINTP
DACIN
6
6
HEREQ0
HEACK0
6
6
6,8
CEREQ1
CEACK1
PFCLK
6
6
6
OPINTP
HDINTP
ITV
12
12
9
11
10
10
MTENC
OPN
HDUSENS
CV_OPN
FANLOCK
BUZZER
9
9
7
8
7
7
12
12
3R0V
VREF
SENSFIX
SENSMOVE
HDTMP
MOTTMP
VHEADMON
HEADRES
MTTH
PEELSENS
P11/SCK0/INTP11
P12/RXD0/SI0
P13/TXD0/SO0
P20/NMI
P21/RXD1/INTP21
P22/TXD1/INTP22
P23/SCK1/INTP23
P24/SI1/INTP24
P25/SO1/INTP25
P50/INTP50/DMARQ0
P51/INTP51/DMAAK0
P52/INTP52/TC0
P53/INTPC00/TIC0/DMARQ1
P54/INTPC01/DMAAK1
P55/TOC0/TC1
PDH0/D16/INTPD0
PDH1/D17/INTPD1
PDH2/D18/INTPD2/TOC4
PDH3/D19/INTPD3
PDH4/D20/INTPD4
PDH5/D21/INTPD5/TOC5
PDH6/D22/INTPD6/INTP100/TCUD10
PDH7/D23/INTPD7/INTP101/TCLR10
PDH8/D24/INTPD8/TO10
PDH9/D25/INTPD9/TIUD10
PDH10/D26/INTPD10/INTP110/TCUD11
PDH11/D27/INTPD11/INTP111/TCLR11
PDH12/D28/INTPD12/TO11
PDH13/D29/INTPD13/TIUD11
PDH14/D30/INTPD14/PWM0
PDH15/D31/INTPD15/PWM1
PAL0/INTPL0/A0
PAL1/INTPL1/A1
P65/INTP65/INTPC10/TIC1
P66/INTP66/INTPC11
P67/INTP67/TOC1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
P72/DMARQ2/INTPC20/TIC2
P73/DMAAK2/INTPC21
P74/TC2/TOC2
P75/DMARQ3/INTPC30/TIC3
P76/DMAAK3/INTPC31
P77/TC3/TOC3
PCM0/WAIT
PCM1
PCM2/HLDAK
PCM3/HLDRQ
PCM4/REFRQ
PCM5/SELFREF/ADTRG
PAH0/A16
PAH1/A17
PAH2/A18
PAH3/A19
PAH4/A20
PAH5/A21
PAH6/A22
PAH7/A23
PAH8/A24
PAH9/A25
PCS0/CS0
PCS1/CS1
PCS2/CS2/IOWR
PCS3/CS3
PCS4/CS4
PCS5/CS5/IORD
PCS6/CS6
PCS7/CS7
U2
1
R46
100k/1%
2
4
REF
A1
A2
K
NC
3
5
U3
BD5328FVE
V3R3
uPC1093TA
5
C3
0.1u/16
2
4
RESET
VDD
VOUT
SUB
GND
CT
10,14
1
3
T119
28
PCD0/SDCKE
PCD1/BUSCLK
PCD2/SDCAS
PCD3/SDRAS
RESET
T122
PCT0/LLWR/LLBE/LLDQM
PCT1/LUWR/LUBE/LUDQM
PCT2/ULWR/ULBE/ULDQM
PCT3/UUWR/UUBE/UUDQM
PCT4/RD
PCT5/WE/WR
PCT7/BCYST
V3R3
C4
1000p/50
R49
*0
T377
R193
0
R53
0
R194
*0
15
16
156
MODE1
MODE0
PLLSEL
T128
112
113
114
117
118
119
120
121
122
123
124
125
126
127
130
131
T30
T31
T32
T34
T36
T38
T40
T42
T43
T44
T46
T48
T50
T52
T54
T56
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
76
75
T57
T59
A1
74
73
72
69
68
67
66
65
64
63
62
61
60
59
T62
T63
T64
T66
T68
T70
T72
T74
T76
T77
T78
T80
T82
T84
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
58
57
52
51
50
49
48
47
46
45
T87
T89
T90
T91
T92
T94
T96
T98
T100
T102
A16
A17
A18
A19
A20
A21
A22
A23
A24
44
43
42
41
40
37
36
35
T105
T107
T109
T110
T111
T113
T114
T115
91
88
87
86
T116
T117
T120
T121
83
82
81
80
79
78
77
T123
T124
T125
T126
T127
T129
T130
D[31:16]
A[24:1]
R48
V850/ME2
T118
Title
A4
6-5
RIBENC
A[24:1]
9
4,5,6
RIBSENS
-ROM1CS
-SDRAMCS
-IOWR
-GACS
DCMTR0
-IORD
-ROM2CS
DCMTR1
4
5
6
6
12
6
4
12
SDCKE
BUSCLK
-SDCAS
-SDRAS
5
5,6
5
5
LLDQM/-LLBE
LUDQM/-LUBE
ULDQM/-ULBE
UUDQM/-UUBE
-RD
-WE/-WR
FANCTL
4,5,6
4,5,6
5
5
4,6
5
10
2007/1/18
2007/1/18
2007/1/18
2007/1/18
2007/1/18
(2/15)
Revision
JN66701-0
Date:
File:
D[31:16]
V3R3
Size
4,5,6
22k
161
UDM
160
UDP
159
P10/UCLK/INTP10
D[15:0]
R43
T16
T18
T21
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
22k
22k
22k
22k
UDM
UDP
T3
T4
T5
T7
T9
T11
T13
T14
T15
T17
T19
T22
T23
T24
T26
T28
R42
R41
R40
R39
1
JIT1
2
JIT0
169
SSEL1
170
SSEL0
92
93
94
95
96
97
98
99
104
105
106
107
108
109
110
111
22k
22k
22k
R33
22k
V5R0
20k/1%
T6
T8
T10
T12
D[15:0]
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
R38
R37
R36
R32
22k
T108 R45
15
6
14
R13
*0
RFOSC
LDSR0
LDTR0
RFRUN
USBON
R44
220
R12
0
C2
12p/50
C1
12p/50
V3R3
R2
*0
16MHz T2
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V3R3
J1
U1C
D
TRCDATA3
TRCDATA2
TRCDATA1
TRCDATA0
TRCEND
TRCCLK
DDO
DDI
DRST
DMS
DCK
132
133
136
137
138
139
T132
T134
T136
T138
T140
T142
R54
R55
R56
R57
R58
R59
0
0
0
0
0
0
T133
T135
T137
T139
T141
T143
140
141
142
143
144
T144
T146
T147
T148
T149
R60
T145
1
3
5
7
9
11
13
15
17
19
21
23
TRCCLK
TRCDATA0
TRCDATA1
TRCDATA2
TRCDATA3
TRCEND
DDI
DCK
DMS
DDO
DRSTZ
2
4
6
8
10
12
14
16
18
20
22
24
24FLT
V3R3
R61
R63
R64
R65
V850/ME2
U1B
V3R3
38
53
70
89
100
115
128
150
3
162
163
EVSS
EVSS
EVSS
EVSS
EVSS
EVSS
EVSS
EVSS
AVSS
OSCVSS
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
PLLVDD
26
55
84
102
134
157
167
V3R3
R66
*22k
2,11
2,11
6
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
0.1u/16
39
54
71
90
101
116
129
151
14
166
V1R5
C22
C21
C20
C19
C18
C17
C16
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
AVDD
UVDD
OSCVDD
C15
C14
C13
C12
C11
C10
C9
C8
C7
C6
C5
R62
22k
4.7k
4.7k
4.7k
4.7k
IVSS
IVSS
IVSS
IVSS
IVSS
IVSS
PLLVSS
VREF
R67
22k
R68
22k
DACIN
DACCLK
CS_DAC
R195
22k
R196
*22k
27
56
85
103
135
158
168
U4
12
DI
11
CLK
10
CSB
13
VFS
3
4
7
8
AO1
AO2
AO3
AO4
TM1 VDD
TM2
NC1 VSS
NC2
1
2
5
6
T150
T151
T152
T155
V5R0
PFMOTCU
PESNSLED
R69
T153
22k
3
2
C23
1000p/50
R192
*22k
9
14
8
9
U5A
+
-
T154
MTREF
12
BA2904
C24
0.1u/16
BH2227
V850/ME2
A
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-6
Revision
JN66701-0
Date:
File:
(3/15)
A
Sheet of
Drawn By:
2
2,5,6
D[15:0]
2,5,6
D[15:0]
A[24:1]
A[24:1]
V3R3
C25
0.1u/16
A20
N 4
2 V
G
TC7SH04
A21
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
R70
*0
U6
A22
R72
10
9
16
17
48
1
2
3
4
5
6
7
8
18
19
20
21
22
23
24
25
13
T157
26
28
11
T159
V3R3
C26
U9
U8A
U7A
T156
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
NC
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
V3R3
BYTE
CE
OE
WE
A22
47
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
R71
0
T158
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
A21
15
RY/BY
12
RESET
D
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CE
OE
WE
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
V3R3
BYTE
26
28
11
W19B320ATT7M
*0.1u/16
10
9
16
17
48
1
2
3
4
5
6
7
8
18
19
20
21
22
23
24
25
13
47
15
RY/BY
12
RESET
*S29JL064H70TFI000
1 V5
2
4
G3
*7SH32
2,6
2,5,6
2,5,6
2
2
-RD
LLDQM/-LLBE
LUDQM/-LUBE
-ROM1CS
-ROM2CS
J2
CPU Address
ROM Address
000000h
--
(N/A)
100000h
100000h
200000h
200000h
LUDQM/-LUBE
LLDQM/-LLBE
-ROM1CS
-RD
D0
D2
D4
D6
D8
D10
D12
D14
For 16M
(000000h)
300000h
300000h
400000h
400000h
For 32M
(000000h)
500000h
500000h
600000h
600000h
V3R3
C27
V3R3
*0.1u/16
T161
700000h
4 N
A1
A3
A5
A7
A9
A11
A13
A15
A17
A19
A21
T160
V3R3
D1
D3
D5
D7
D9
D11
D13
D15
*8830E-050
V 2
G
*TC7SH04
R73
*3.3k
U10
For 64M
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A2
A4
A6
A8
A10
A12
A14
A16
A18
A20
U7B
V3R3
14
VCC1
37
VCC2
27
GND1
46
GND2
W19B320ATT7M
U8B
14
VCC1
37
VCC2
27
GND1
46
GND2
C28
0.1u/16
Title
C29
0.1u/16
Size
A4
*S29JL064H70TFI000
6-7
V3R3
Number
Revision
JN66701-0
Date:
File:
(4/15)
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
2,4,6
D[15:0]
2,4,6
A[24:1]
D[15:0]
U11A
A[24:1]
36
35
22
34
33
32
31
30
29
26
25
24
23
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A21
A22
A23
A24
2 -SDRAMCS
2 -WE/-WR
R74
R75
R76
R77
R78
R79
*0
0
*0
*0
0
*0
T162
T163
20
21
40
19
16
37
38
2 SDCKE
2,6 BUSCLK
NC(A12)
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
BS0
BS1
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
NC
RAS
CAS
CS
WE
CKE
CLK
UDQM
LDQM
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
D[31:16]
2,4,6
A[24:1]
D[31:16]
U12A
A[24:1]
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
18
17
36
35
22
34
33
32
31
30
29
26
25
24
23
NC(A12)
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
20
21
BS0
BS1
40
NC
19
16
2 -SDRAMCS
2 -WE/-WR
39
15
CS
WE
37
38
2 SDCKE
2,6 BUSCLK
2,4,6
2,4,6
A[24:1]
D[15:0]
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
U13A
A[24:1]
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
36
35
22
34
33
32
31
30
29
26
25
24
23
20
21
40
19
16
2 -SDRAMCS
2 -WE/-WR
37
38
2 SDCKE
2,6 BUSCLK
NC(A12)
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
BA0
BA1
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
RAS
CAS
18
17
V3R3
CKE
CLK
VSSQ
VSSQ
VSSQ
VSSQ
VSS
VSS
VSS
1
14
27
3
9
43
49
C30
C31
C32
C33
V3R3
C34
C35
39
UDQM
15
LDQM
LLDQM/-LLBE
LUDQM/-LUBE
VSSQ
VSSQ
VSSQ
VSSQ
VSS
VSS
VSS
2 -SDCAS
2 -SDRAS
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
C36
VSSQ
VSSQ
VSSQ
VSSQ
VSS
VSS
VSS
1
14
27
3
9
43
49
C37
C38
C39
C40
V3R3
C41
C42
C43
6
12
46
52
28
41
54
W9864G6EH-7
W9864G6EH-7
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
V3R3
U12B
6
12
46
52
28
41
54
V3R3
U13B
NC
CS
WE
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
*HY57V281620E
2,4,6
2,4,6
18
17
2 -SDCAS
2 -SDRAS
U11B
2,4,6
RAS
CAS
D31
D30
D29
D28
D27
D26
D25
D24
D23
D22
D21
D20
D19
D18
D17
D16
W9864G6EH-7
2 -SDCAS
2 -SDRAS
D[15:0]
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
2 ULDQM/-ULBE
2 UUDQM/-UUBE
LLDQM/-LLBE
LUDQM/-LUBE
2,4,6
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
UDQM 39
LDQM 15
CKE
CLK
W9864G6EH-7
1
14
27
3
9
43
49
6
12
46
52
28
41
54
*HY57V281620E
A
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-8
Revision
JN66701-0
Date:
File:
(5/15)
A
Sheet of
Drawn By:
X3
*16MHz
R80
R81
*1M
*1M
T164
C51
12p/50
T165
C52
*12p/50
2,4,5
27
28
32
33
34
35
36
A18
A17
A16
A4
A3
A2
A1
A18
A17
A16
A4
A3
A2
A1
3
Xout
A[24:1]
A[24:1]
Xin
2,4,5
T166
U14
CLKIN
CLKSEL
PFCLK
PFCNT1
PFCNT2
PFMXB
PFMXA
PFMB
PFMA
PFON
D[15:0]
D[15:0]
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
T202
T203
T204
T205
T207
T209
T211
T213
T214
T215
T216
T217
T218
T219
T220
T221
T222
T223
T224
6
54
T225
26
V5ON
LEDFIX_T
LEDFIX_R
10
9
9
CNINTP
CEREQ1
CEACK1
xSLCT-IN
xPRIME
xATFD-XT
xSTROBE
PLH
xFAULT
SLCT
2
2
2
13
13
13
13
13
13
13
PE
BUSY
xACKNLG
OBDIR
13
13
13
13
PLDRXDO
-GRESET
2,8,13
1k
1k
1k
1k
DATA[7:0]
DATA[7:0]
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
13
V3R3
R92
22k
PLDRXDI
14
V3R3
29
112
118
A
Title
Size
6-9
(6/15)
Revision
JN66701-0
Date:
File:
12
12
11
11
11
11
A4
NA
HPSENS0
HPSENS1
SW4
SW3
SW2
SW1
U_GA_uPD65946GJ-165-3EB-A
T193
T196
T198
T200
1000p/50
0.1u/16
TEB
SMC
AMC
8
10
11
55
56
57
58
59
62
63
64
65
66
67
68
69
70
71
72
73
74
76
R88
R89
R90
R91
V3R3
C56
0.1u/16
RESET
R83
NA
22k
C60
0.1u/16
RXDOUT
RXDIN
OPINTP
R82
R87
C59
0.1u/16
GND
GND
GND
GND
GND
GND
GND
GND
GND
T188
T190
T192
T195
T197
T199
HD[4:1]
1000p/50
C58
4
15
31
45
60
75
91
106
120
VDD
VDD
VDD
VDD
VDD
7
7
7
HD[4:1]
1000p/50
C57
1
5
30
61
90
T174
T175
T176
T177
T178
T179
T180
T181
T182
C55
V3R3
HDCLK
HDVON
HCVON
CPU
22k
PM0
PM1
PM2
PM3
2
2
2
7
7
HD4
HD3
HD2
HD1
CRYSTAL
R86
T208
T210
T212
HDINTP
HEREQ0
HEACK0
-HDLAT
-HDSTB
R83
*0
1000p/50
CPRTYP0
CPRTYP1
IETYP0
IETYP1
95
96
97
98
2,8
9
9
8
8
8
8
8
C54
12
12
13
13
T206
CNINTP
CNREQ1
CNACK1
SELECTIN
INIT
AUTOFD
STROBE
PLH
FAULT
SELECT
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
PEND
BUSY
ACK
OTDIR
7
84
85
86
87
88
89
92
93
94
R82
0
PFCLK
LEDMOVE_T
LEDMOVE_R
-PFMB
-PFMA
PFMB
PFMA
PFON
C53
LLDQM/-LLBE
LUDQM/-LUBE
ITV
IORD
IOWR
CS
RD
SCK
LLBE
LUBE
LWR
HWR
OPINTP
SW6
SW5
SW4
SW3
SW2
SW1
LED3
LED2
LED1
T168
T169
T170
T171
T172
V3R3
22k
2,4,5
2,4,5
16
17
18
19
20
21
22
23
24
25
ITV
-IORD
-IOWR
-GACS
-RD
OPRS
OPRD
OPE
OPD3
OPD2
OPD1
OPD0
9
12
13
107
108
109
110
111
113
115
116
117
2,5
22k
2
2
2
2
2,4
77
78
79
80
81
82
83
HDINTP
HDREQ0
HDACK0
HDLTH
HDSTB
HDATA4
HDATA3
HDATA2
HDATA1
HDCLK
HDVON
HCVON
14
99
100
101
102
103
104
105
BUSCLK
T167
R85
T183
T184
T185
T187
T189
T191
T194
CS_DAC
CS_LCD
LCD_CD
LCD_LED4
LCD_LED3
LCD_LED2
LCD_LED1
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
114
R84
3
11
11
11
11
11
11
37
38
39
40
41
42
43
44
46
47
48
49
50
51
52
53
119
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V24R0
3
T228
HDVON
10k
T229
DTC114EM
Q2
V3R3
2
4
T227
10k
6
Q1
2SJ505S
R93
10k
T226
R94
10k
R95
30k/1%
D1
RB521S
R96
1k
VHDON
R97
3.3k/1%
VHEADMON
HEADRES
C61
*1000p/50
V3R3
10k
10k
T230
10k
HCVON
10k
Q3
DTA114EM
R99
100/1%/2012
DTC114EM
Q29
R100 1k
T231
HEADRES
C62
*1000p/50
D2
RB521S
6 HD[4:1]
V5R0
U15A
HD[4:1]
HD1
HD2
HD3
HD4
2
4
6
8
11
13
15
17
6 -HDSTB
6 HDCLK
6 -HDLAT
1
19
A1
A2
A3
A4
A5
A6
A7
A8
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
18
16
14
12
9
7
5
3
T232
T233
T234
T235
T236
T237
T239
J3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
C63
10u/10
R101
T238
HEADSTB
HEADD4
1OE
2OE
HEADD3
HEADD2
HEADSTB
HEADCLK
HEADD1
HEADLAT
74HCT244
V3R3
2 HDTMP
C64
*1000p/50
R102
30k/1%
U15B
VCC
GND
V5R0
S30B-PHDSS
20
10
C65
0.1u/16
74HCT244
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-10
Revision
JN66701-0
Date:
File:
(7/15)
A
Sheet of
Drawn By:
V24R0
+
C66
100u/50
V3R3
U16A
1
2
2,6 PFCLK
6 PFON
T240
15
14
C67
1u/B16
2,6,13
A
B
R104
10k
13
4
V3R3
CLR
74VHC123
U17
T243
T245
V5
1
2
G3
R105
10k
C68
0.1u/16
T242
T244
Q4
XP132A11A1
T241
RX/CX
CX
-GRESET
Q
Q
1
2
3
R103
200k
5
6
7
8
Q5
DTC114EM
10k
10k
J4
PFMTCOM
T246
74AHC1G08
1
2
3
4
5
6
C69
U18
7
12
C
6
6
6
6
R106
3 PFMOTCU
6
5
17
16
PFMA
-PFMA
PFMB
-PFMB
T251
20k/1%
R107
20k/1%
3
C71
0.1u/16
T252
9
14
T253
10
100p/100
OUTA
OUTA
OUTB
OUTB
VSA
VSB
INA
INA
INB
INB
OUTA
-OUTA
OUTB
-OUTB
T247
T248
T249
T250
8
1
18
11
-A
BCOM
-B
A
ACOM
B
B6B-EH-*
PF MOTOR
C70
TDA
TDB
REFA
100p/100
2
13
RSA
REFB
GA
GB
RSB
4
15
VREF
J5
U_MTR_SLA7033MPR
1
2
D6
D5
D4
*SFPB66
*SFPB66
*SFPB66
*SFPB66
100p/100
C79
0.1u/16
2 MOTTMP
C78
VREF
R111
3.3k/1%
VREF
R113
V3R3
TMPOFF
C80
0.1u/16
+
-
1000p/50
R114
3.3k/1%
3
2
T254
T255
R115
1k
uPC393GR-9LG
uPC393GR-9LG
R116
*3.3k
Title
A4
Number
6-11
Revision
JN66701-0
Date:
File:
(8/15)
Size
R110
3.3k/1%
R112
1k/1%
100k
U19A
8
4
D3
V-
100p/100
V+
C75
V3R3
74VHC123
U19C
16
74VHC123
CLR
C77
100p/50
100p/100
11
C74
RX/CX
CX
PF MOTOR THRM
100p/100
7
6
U16C
C73
5
Q
12
Q
A
B
0.68/2%/3W
0.68/2%/3W
U16B
9
10
C76
100p/50
C72
R109
R108
B2B-PH-K-S
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
6
6
6
6
LEDFIX_R
LEDFIX_T
LEDMOVE_R
LEDMOVE_T
R117
U20A
1
SENSFIX
C81
1000p/50
3
2
+
-
R118
R203
22k
R202
22k
Q25
2SC5658
T368
Q26
2SC5658
T256
10k
T371
Q7
DTA114EM
T257
Q8
DTA114EM
10k
Q27
2SC5658
T258
T370
10k
Q6
DTA114EM
10k
10k
Q28
2SC5658
Q9
DTA114EM
T259
T260
T261
T262
T263
V3R3
J6
1
2
100
J21
T265
*100
*BA2904
R121
3.3k
1
2
3
4
R206
3.3k
T379
T266
T264
R201
22k
10k
T369
R200
22k
10k
V3R3
10k
V5R0
VR2
10k
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
B4B-PH-K-E
FIX LED/SENSOR
Blue
VR1
10k
UP LED A
UP LED K
B2B-PH-K-E
T364
T365
V3R3
10k
10k
10k
10k
J7
R120
100
V5R0
SENSMOVE
C83
1000p/50
V+
+
-
T267
R122
1
2
3
4
T268
*100
V-
T269
R124
3.3k
DOWN LED A
DOWN LED K
DOWN TR C
DOWN TR E
B4B-PH-K-R
ADJUSTABLE LED/SENSOR
Red
VR4
10k
VR3
10k
R207
3.3k
T380
*BA2904
5
6
UP LED A
UP LED K
B2B-PH-K-R
J22
Q18
DTC114EM
C82
*0.1u/16
U20B
C
1
2
Q19
DTC114EM
T367
T366
10k
10k
10k
10k
Q20
DTC114EM
Q21
DTC114EM
V5R0
3 PESNSLED
R125
22k
C84
0.1u/16
T271
5
6
C85
1000p/50
+
-
V+
T272
T270
R126 200
T273
Q10
2SC5658
U5B
T274
V3R3
J8
R128
2 RIBENC
1k
1
2
3
4
T275
T276
R129
10k
C87
1000p/50
R130
100
V3R3
R131
22k
R132
2 HDUSENS
T278
1k
R127
75/1%/2012
B4B-PH-K-K
RIBBON ENCODER
Black
J9
B2B-PH-K-K
V3R3
U19B
7
+
-
R208
3.3k
2 RIBSENS
C86
*1000p/50
LED A
LED K
TR C
TR E
1
2
C88
1000p/50
V3R3
T279
6
5
uPC393GR-9LG
V3R3
R135
10k
T280
R133 1k
1
2
3
R134
1M
C89
1000p/50
HEAD UP
Black
J10
B3B-PH-K-S
RIBBON END
Title
T281
Size
R136
10k
A4
CL-S700/CL-S703/CL-S700R
6-12
(9/15)
Revision
JN66701-0
Date:
File:
VBA2904
A
Sheet of
Drawn By:
U26
T376
J11
T286
1
2
3
4
5
6
7
8
9
10
V3R3
V5
V24R0
C93
47u/35
Vin
V1R5
GND
U21
V3R3
T284
Vout
C90
1u/B16
C94
47u/35
6
4
T283
BH15MA3WHFV
2
VI
O1
O2 3
STB
N
VSS
T282
C91
1u/B16
C92
0.1u/16
NJM2391DL1-33
T287
B10B-EH
POWER
R137
0/2012
R204 0/2012
T288
V5R0
T372
R197
*10k
V3R3
T374
V5ON
2,14
RESET
T373
R198
*22k
R199
Q22
*2SJ518
C114
*0.1u/16
T375
*10k
Q24
*2SC5658
Q23
*2SC5658
C
V24R0
R138
240/3216
T289
R140
3.3k/3216
BZ1
PKM13EPYH4002-B0
R141
1k/3216
D7
RB521S
T290
10k
10k
2 BUZZER
Q11
DTC114EM
V24R0
B
D8
SFPB66
T291
J12
1
2
3
B3B-EH-K
R142
2 FANCTL
T293
1k
2SK3577
Q12
FAN CNT
R143
22k
V3R3
R145
2 FANLOCK
1k
R144
22k
T294
C95
1000p/50
A
Title
Size
A4
Number
6-13
Revision
JN66701-0
Date:
File:
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V3R3
V5R0
J13
R146
22k
Standard
Custom Type
R147
R148
R149
R150
NA
NA
NA
NA
TXD1
RXD1
2 TXD1
2 RXD1
R147
R148
R149
R150
2 RFRUN
2 RFOSC
*0
*0
0
0
T295
T296
T297
T298
RFRUN
RFOSC
1
2
3
4
5
6
7
8
9
10
B10B-ZR
RF-ID
V3R3
R151
22k
V3R3
R152
22k
J14
V5R0
T299
DACIN
DACCLK
CS_LCD
LCD_CD
6
6
6
6
LCD_LED1
LCD_LED2
LCD_LED3
LCD_LED4
T300
T301
T302
T303
T304
T305
6
6
6
6
10k
Q13
DTC114EM
Q15
DTC114EM
Q14
DTC114EM
T306
T307
10k
10k
10k
10k
10k
SW1
SW2
SW3
SW4
10k
2,3
2,3
6
6
10k
Q16
DTC114EM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
22FMN-BMT-A-TF
OPE PANE
V3R3
CV_OPN
R191 1k
R190
22k
C113
1000p/50
V5R0
J20
1
2
3
4
T378
R205
180/2012
B4B-PH-K-S
A
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-14
Revision
JN66701-0
Date:
File:
(11/15)
A
Sheet of
Drawn By:
Option Select
Cutter
Rewinder
Peeler
None
CPRTYP0
Low
High
Low
High
CPRTYP1
High
Low
Low
High
D
V3R3
V3R3
DCMTR0
DCMTR1
6
6
2
HPSENS0
HPSENS1
MTTH
R156
R157
R158
R159
R160
1k
V24R0
J15
R153
22k
2
2
VREF
R154
22k
1
2
3
4
5
6
7
8
9
10
11
R155
3.3k/1%
T308
1k
1k
1k
100
T309
T310
T311
T312
C96
1000p/50
C97
1000p/50
C98
1000p/50
B11B-PASK
CUTTER & REWINDER
C
V3R3
V3R3
R161
1k
6
6
CPRTYP0
CPRTYP1
MTREF
R162
1k
V3R3
V3R3
V5R0
J16
R163
22k
2
2
MTENC
OPN
R165
100
T313
R166
100
T315
C99
1000p/50
R164
22k
C100
1000p/50
B7B-PASK
V3R3
R168
PEELSENS
REWINDER
T316
R167
2.4k/1%
D9
*RB521S
100
1
2
3
4
5
6
7
T317
R169
3.3k/1%
A
Title
Size
A4
JN66701-0
Date:
File:
6-15
(12/15)
Revision
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
6 OBDIR
6
6
6
6
6
6
6
6
6
6
6
xACKNLG
BUSY
PE
SLCT
xFAULT
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA[7:0]
DATA[7:0]
xSTROBE
xATFD-XT
xPRIME
xSLCT-IN
PLH
R170
100
T326
C101
12p/50
U22A
V3R3
1
2
3
4
5
6
8
9
11
12
13
14
16
17
19
20
21
22
23
24
HD
A9
A10
A11
A12
A13
A1
A2
A3
A4
A5
A6
A7
A8
PLHIN
A14
A15
A16
A17
HLH
J17
DIR
Y9
Y10
Y11
Y12
Y13
B1
B2
B3
B4
B5
B6
B7
B8
PLH
C14
C15
C16
C17
HLHIN
48
47
46
45
44
43
41
40
38
37
36
35
33
32
30
29
28
27
26
25
74LVX161284
T318
xSTROBE
T319
DAT0
T320
DAT1
T321
DAT2
T322
DAT3
T323
DAT4
T324
DAT5
T325
DAT6
T327
DAT7
T328
xACKNLG
T329
BUSY
T330
PE
T331
T332
T333
T334
SLCT
xPRIME
xATFD-XT
xFAULT
V3R3
V5R0
R171
3.3k
T335
xSLCT-IN
T336
C102
*12p/50
xRESET
V3R3
IEEE1284
-GRESET
PS-40PE-D4T1
U23
2,6,8
C103
*0.1u/16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
*74AHCT1G125
V3R3
B
V5R0
R172
22k
V3R3
U22B
GND
GND
GND
GND
R174
R175
6 IETYP0
6 IETYP1
7
VCC
18
VCC
31
VCC_CABLE
42
VCC_CABLE
C104
10u/10
R173
22k
T337
T338
3.3k
3.3k
C105
0.1u/16
10
15
39
34
74LVX161284
NOT CONNECTED
NETWORK BD
CENTRO CN
IETYP0
HIGH
LOW
HIGH
IETYP1
HIGH
HIGH
LOW
A
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-16
Revision
JN66701-0
Date:
File:
(12/15)
A
Sheet of
Drawn By:
RS232C I/F
V5R0
FG1
Lock_pin
J18
T339
T340
T341
T342
T343
V3R3
C106
1u/B16
U24
19
C107
1u/B16
C109
1u/B16
T344
2
4
T346
T347
5
6
T349
2
2
6
2
TXD0
LDTR0
PLDRXDI
LDSR0
2,10
13
12
15
10
TXD0
LDTR0
RXD0
LDSR0
1
20
RESET
18
Vcc
C1+
V+
T345
TXD
RXD
RTS
CTS
DSR
V5R4
C108
1u/B16
C1-
V5R4
C2+
V-
C217
8
16
9
T1I
T2I
R1O
R2O
T1O
T2O
R1I
R2I
EN
SHDN
11
NC1
14
NC2
T348
C110
1u/B16
R176
3.3k
T350
T352
R178
R179
*0
0
R180
R181
*0
0
R177
*3.3k
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
DBR40-251F100
T351
DTR
FG2
Lock_pin
GND
ZT3222LEEY
R176
R177
R178
R179
R180
R181
RTS
NA
NA
NA
DTR
NA
NA
NA
A
Title
Size
A4
Number
6-17
Revision
JN66701-0
Date:
File:
(14/15)
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V3R3
10k
10k
Q17
DTA114EM
T353
V3R3
U25B
2
R182
1k
USBON
R183
1.5k
74VHC132
U25C
2
UBINTP
U25A
T356
10
74VHC132
T354
T357
R184
T358
20k/1%
R185
0/2012
T359
USBVCC
R186
R187
R188
24/2012
24/2012
0/2012
T360
T361
T362
DM
DP
USBLGND
74VHC132
2
2
J19
UDM
UDP
U25E
U25D
12
11
T363
13
DUSB-BRA42
R189
30k/1%
C111
33p/50
1 VCC
2 DM
3 DP
4 GND
SG5
USB I/F
V3R3
14
7
C112
0.1u/16
74VHC132
74VHC132
A
Title
Size
A4
Number
CL-S700/CL-S703/CL-S700R
6-18
Revision
JN66701-0
Date:
File:
(15/15)
A
Sheet of
Drawn By:
C47
CN1
F1
INPUT
1
2
Q7
470
3
20
8
13
10
11
12
5
14
3
9
OVP
T-OFF
F/B
T-ON
1
2
4
18
6
7
CF
ON/OFF
15
NC
NC
16
CT
NC
17
E
GND
19
DET
CLM+
NC
M51995AFP
(MITSUBISHI)
C35
R58
1/4W 100k
6-19
Q8
AC100V/240V(85-264V)
200V 1A
1DL42A
(TOSHIBA)
D13
IC3
CLM-
VOUT
+24V
+ 5V
FB5
MIN
0.04A
0.10A
TYP
5.00A
1.50A
128W
Size
Title
A4
Date:
File:
Number
R240
2200pF
R211
DA200
80V 0.1A
1SS301
(TOSHIBA)
R210
5.1B
ZD202
15B
ZD203
1/4W 10k
C203
0.47uF
C229
1/4W 10k
1/4W 10k
R236
1/4W 10k
R235
1/4W 10k
R234
1/4W 10k
R233
1/4W 10k
R225
R224
15B
ZD200
35V 6800uF
0.1uF
1/4W 220
C225
1/4W 220
R239
35V 1000uF
C217
1/4W 10
SWo
Vos
2200pF
1/4W 10
1/4W 10
Vin
S.S
DS202
SI-8050J
IC102 (SANKEN)
C211
R219
1/4W 10
R213
1/8W 470
Q200
C207
PI1
PI2:B
C206
0.033uF
1k
R209
0.1uF
1/4W 0
GND
R217
R212
1/4W 470
27k
R206
C202
DS204
35V 6800uF
(NIHON INTER)
400V 16A
RN1402 (TOSHIBA)
10k-10k
TB FCF16A40
500
1k
C205
R203
0.01uF
C204
R202
TA
PI1:B
T1
PI1
R201
MM1431ANR
IC200
2kV 100pF
630V 0.01uF
C28
2W 47k
D9
0.022uF
200V 1A
CRH01
(TOSHIBA)
2W 68
R47
R48
2W 47k
1NU41
(TOSHIBA)
D8
R200
2W 47
VR200
FB4
R65
2W 27k
FSU10A60
(NIHON INTER)
FB3
600V 10A
C200
500V 220pF
3.3k
Q6
70BB
1000V 8A
2SK2613 (TOSHIBA)
C31
R54
1/4W 10k
R42
1/4W 270k
R208
30B
ZD3
R49
2W 27k
R38
1/4W 270k
D4
27k
R207
TF1
125
2W 27k
R64
R43
1/4W 270k
R66
R44
1/4W 270k
630V 0.047uF
C40
1/4W 270k
1/4W 270k
R70
R214
R216
C215
50V 5A
2SA1244-Y/Q (TOSHIBA)
L4
1/4W 4.7
10uH
R61
1SS355
(ROHM)
D18
40V 1A
CRS04
(TOSHIBA)
200V 1A CRH01
(TOSHIBA)
D12
R39
R69
R40
450V 220uF
C25
2kV 220pF
250V 1500pF
FG
R60
R88
1/4W 100
D7
0.01uF
C26
18k
R72
3.9k
80V 0.1A
1SS355 (ROHM)
R82
R94
-
D11
R62
VCC
R97
D16
70BB
5W 0.1
R79
UDZS30B(ROHM)
ZD4
C41
1/4W 47
C39
R78
1/4W 82
30B
56uF
1/4W 47
R76
TLP421
(TOSHIBA)
R67
2W 100k
PI2:A
R71
2W 100k
R81
Q12
47
D15
820k
80V 0.1A
1SS355
(ROHM)
CRH01
(TOSHIBA)
200V 1A
R73
10k
330k
C33
R56
0.15uF
R86
VF
33k
(F.E)
R80
GND
10k
FA5502
22k
R74
14
SYNC
7
C34
CS
C46
0.22uF
REF
9
8
4
6
D17
ON/OFF VIN5
VFB
CT
3.9k
10
47uF
VC
22k
R87
1/4W 47
0.022uF
1/8W 220k
D14
R84
80V 0.1A
1SS355
(ROHM)
VCC
1/4W 2.2
R89
OVP
C27
IC1
200V 1A
CRH01
(TOSHIBA)
C30
OUT
IFB
R30
0.022uF
IIN-
1/4W 10k
C36
VDET
70BB
D6
35V 150uF
D10
1/8W 0
1/4W 47
R29
40V 1A
0.22uF
IDET
R27
C43
R28
FB2 Q3
0.22uF
1/4W 2.2
C32
DS2
0.22uF
1/4W 10k
R25
33k
R26
C29
R91
50V 5A
2SA1244-Y/Q
(TOSHIBA)
40V 1A
1/8W 0
R92
200V 1A
CRH01 (TOSHIBA)
70BB
D5
50V 0.15A
2SA1162Y
(TOSHIBA)
40V 1A
CRS04
(TOSHIBA) D3
L3
CZ59303-G
1/4W 2.2
22k
R90
FB1 Q2
R55
1/4W 10
R63
1/4W 27
R23
C13
16
3
2
1
12
15
13
11
1uF
1/4W 10
R24
R20
C37
0.1uF
C7
630V 1.0uF
R3
470pF
R53
C38
R96
1/4W 2.2
470
R51
R59
100k
1/8W 27
R21
TLP421
(TOSHIBA)
C20
5.6k
R46
1/4W 220k
PI1:A
0.1uF
0.1uF
C45
0.047uF
R57
33k
R45
100pF
220pF
C17
R95
R12
1/4W 220k
R93
Z1
1/4W 220k
R15
0.1uF
R50
100k
R75
1/4W 33k
5W 0.1
Q1
R52
100
R68
C23
0.1uF
C21
C49
2.2k
R41
0.01uF
470pF
C19
18B
LB
C9
C6
275V 0.68uF
120B
R1
120B
275V 0.33uF
UDZS18B(ROHM)
ZD7
DS1
600V 10A
D10XB60H
(SHINDENGEN)
LA
1/8W 68k
ZD5
1/4W 100k
C3
C4
250V 1500pF
1.2mH
HR24-122 (KOURINGIKEN)
680V
R83
ZD6
C2
C
5W 0.1
1/8W 68k
C1
R77
1/4W 100k
250V 1500pF
L2
R14
1/8W 68k
B
1.2mH
HR24-122 (KOURINGIKEN)
L1
R2
10
R85
250V T10AH
35V 56uF
FG
FCF16A40
DS200
(NIHON INTER)
CZ62301-G
400V 16A
1000V 1A
JN6601-0
+24V
10
+24V
9
+24V
8
+24V
7
GND
6
GND
5
GND
4
GND
3
GND(+5V)
2
+5V
1
CN200
6
FG
Notes:
1. Part whose constant is shown as "-" is not mounted.
2. Unless otherwise specified, wattage of resistor is 1/10W
and work voltage of capacitor is 50V.
3. Specification of this power supply is as follows.
A
C
80V 0.1A
R220
100uH
L104
MAX
12.8A
1.50A
315W
70BB
POWER SUPPLY
Revision
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V5R0
V3R3
+
C401
47u/16
C402
47u/16
J401
T401
T402
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
T403
R401
R402
R403
R404
T404
T406
T408
T410
T412
T413
T422
T423
T405
1k/1608
1k/1608
1k/1608
1k/1608
T407
T409
T411
LCD_SDI
LCD_SCK
CS_LCD
LCD_CD
V3R3
R405
1M
LED4
LED3
LED2
LED1
T415
T417
T419
T420
T425
T426
T428
J403
1
2
3
4
T427
T429
C408
C409
C410
C411
C412
C413
C414
*0.1u/50
*0.1u/50
*0.1u/50
*0.1u/50
*0.1u/50
*0.1u/50
*0.1u/50
*0.1u/50
C407
T430
J402
C404
0.1u/50
T414
T416
T418
T424
T421
C405
1u/25
V5R0
SW1
SW2
SW3
SW4
22FMN-BMT-A-TF
C403
0.1u/50
R406
180/2012
C406
1u/25
B4B-PH-K-S
LCD_SDI
LCD_SCK
LCD_CD
V5R0
V5R0
T431
T433
R407
D402
310DT
ERROR
T434
SW1
D403
332MG
EVPADC04K
T435
D404
332MG
SW2
V5R0
B3
B4
SW402
A3
B2
A4
R409
180/2012
A3
B2
A4
T436
A1
B1
A2
D405
332MG
A3
B2
A4
B4
PAUSE
PAD401
Anode
T432
SW3
PAD402
Catiode
EVPADC04K
R411
SW404
16/1608
SW403
A1
B1
A2
R410
FEED
180/2012
30FLH-SM1-TB
EVPADC04K
B4
B4
A3
B2
A4
B3
B3
A1
B1
A2
LED2
180/2012
NC
NC
NC
NC
VOUT
VB0+
VB0VB1VB1+
VSS
VDD
BM1
BM0
D7
D6
D5
D4
D3/SDA
D2
D1
D0/SCK
WR1
WR0
CD
RST
/CS
NC
NC
NC
NC
SW401
A1
B1
A2
R408
LED1
180/2012
B3
D401
310MT
POWER
CS_LCD
V5R0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
LED4
R412
180/2012
STOP
SW4
EVPADC04K
T437
D406
332MG
R413
180/2012
MENU
A
LED3
Title
Size
A4
OPE-PANE PCB
Number
CL-S700/CL-S703/CL-S700R
6-20
Revision
JN66704-0
Date:
File:
A
Sheet of
Drawn By:
V5R0
J101
1
2
R101
1k
RE-H022TD-1130
V5R0
IEEE1284
CN101
CN102
xSTROBE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
xSTROBE
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
xACKNLG
BUSY
PE
SLCT
xATFD-XT
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
S.GND
F.GND
VCC/PLH
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
S.GND
xPRIME
xFAULT
S.GND
DATA7
xACKNLG
BUSY
V5R0
PE
SLCT
xPRIME
xATFD-XT
xFAULT
R102
1k(NA)
T101
FUSE
xSLCT-IN
xSLCT-IN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
57RE-40360-830B(D29)
xPRIME
xATFD-XT
SLCT
BUSY
PE
DATA7
xACKNLG
DATA6
DATA5
DATA4
DATA3
DATA2
DATA0
xFAULT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
DATA1
xSTROBE
PS-40PE-D4T1-B1
CN103
Title
PS-40PE-D4T1-B1
Size
A4
Date:
File:
6-21
Revision
JM66825-1
A
Sheet of
Drawn By:
CL-S700/CL-S703/CL-S700R
V24R0
V24R0
J801
DCMTR0
DCMTR1
HPSENS0
HPSENS1
MTTH
CPRTYP0
J802
1
2
3
4
5
6
7
8
9
10
11
V5R0
B11B-EH
R801
1.5k
V5R0
V
G
TC7SH04
Q801
DTC114EM
3.3k
10k
R802
U801
10k
J803
1
2
3
4
5
6
7
8
9
10
11
B11B-PASK
MTREF
MTENC
OPN
PEELSENS
CPRTYP1
V5R0
J804
1
2
3
4
5
6
7
1
2
3
4
5
B5B-PH-K-S
B7B-PASK
A
Title
Size
A4
CL-S700/CL-S703/CL-S700R
6-22
Revision
JN66725-0
Date:
File:
A
Sheet of
Drawn By:
$
"#
*%"#
&
'
'
$
!
%"#
"#
!
!!'
)
#
#
'
%
(#
%
(#
!
+
+
!
%"#
)
'
!
%"#
!!' ')'
!!'
)
%"#
+
+
#
,-./
!!' ')'
6-23
,7/
8-/9
,./9
? !
"01/2
'
/3,4,56
://- 5<
28=6 !>9
CL-S700/CL-S703/CL-S700R
Appendices
APPENDICES
CL-S700/CL-S703/CL-S700R
Appendices
Appendices
Table of Contents
A.
B.
CL-S700/CL-S703/CL-S700R
AP-2
A.
A.
Appendices
External Size Diagram
[CL-S700/CL-S703]
[CL-S700R]
AP-3
CL-S700/CL-S703/CL-S700R
Appendices
B. Mounting Diagrams
B.
Mounting Diagrams
B-1.
Main PCB
CL-S700/CL-S703/CL-S700R
AP-4
B.
B-2.
Appendices
Mounting Diagrams
AP-5
CL-S700/CL-S703/CL-S700R
Appendices
B. Mounting Diagrams
CL-S700/CL-S703/CL-S700R
AP-6
B.
B-3.
Ope-pane PCB
[Parts side]
B-4.
Appendices
Mounting Diagrams
[Solder side]
Centro PCB
CN101
AP-7
CL-S700/CL-S703/CL-S700R
Appendices
B. Mounting Diagrams
B-5.
B-6.
CL-S700/CL-S703/CL-S700R
AP-8
Mettinger Strasse 11
Park House, 643-651 Staines Road
D-73728, Esslingen
Feltham, Middlesex, TW14 8PA
Germany
United Kingdom
Tel: +49 (0) 711 3906 420
Tel: +44 (0) 20 8893 1900
Fax:+49 (0) 711 3906 405
Fax:+44 (0) 20 8893 0080
http://www.citizen-europe.com
!
!
CL-S700/CL-S703/CL-S700R
1-ii