Professional Documents
Culture Documents
Installation Instructions: Parts List
Installation Instructions: Parts List
INSTRUCTIONS
Accessory
Application
2010 MDX
PARTS LIST
Publications No.
BII 42097
Issue Date
JAN 2010
Screws
Flange nuts, 6 mm
Brackets A
Brackets B
24 Flange bolts
Self-tapping screws
08L33-STX-2F00-91
1 of 6
3.
Clip remover
FRONT
Ratchet
10 mm, and 13 mm Sockets
10 mm Combination wrench
Torque wrench
Scraper
INSTALLATION
Client Information: The information in this installation
instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
do-it-yourselfers.
3 CLIPS
(Discard.)
SELF-TAPPING
SCREW
(Reuse.)
NOTE:
910502AR
4.
FRONT
DOOR
FRONT CLIP
(Discard.)
REAR
DOOR
FRONT
LEFT FRONT
SPLASH
GUARD
(Discard.)
LEFT SIDE
SILL PANEL
SELF-TAPPING
SCREW
(Discard.)
2.
4 SELF-TAPPING
SCREWS
(Reuse.)
CLIP REMOVER
5.
910518AR
910501BR
2 of 6
6.
While pulling the front portion of the left side sill panel
away from the body, slide the left side sill panel
forward and remove it. The 11 side clips will stay in
the body.
8.
11 SIDE CLIPS
Turn 45
degrees.
LEFT SIDE
SILL PANEL
11 SIDE CLIPS
(Reuse.)
910503BR
7.
9.
910504AR
Remove the spring nut from the left side sill panel.
REAR DOOR
SPRING NUT
(Reuse.)
VEHICLE
BRACKET
(Discard.)
2 BOLTS
(Reuse.)
LEFT SIDE
SILL PANEL
(Discard.)
910517AR
2 BOLTS
(Reinstall.)
910505AR
3 of 6
LEFT CENTER
TRIM
11 SIDE CLIPS
(Reuse.)
FRONT
4 FLANGE
BOLTS
910506AR
BRACKET A
11. Hold the left center trim up, and fit the front clip and
11 side clips into the holes in the body, then push on
the left center trim until the side clips snap into place.
FRONT
VEHICLE
FRAME
FRONT
BOTTOM VIEW
910508AR
FRONT CLIP
LEFT CENTER
TRIM
11 SIDE CLIPS
910507AR
4 of 6
15. Install the left front end cap to the left running board
with one screw and one 6 mm flange nut.
6 mm
FLANGE
NUT
LEFT FRONT
END CAP
BOTTOM VIEW
LEFT
RUNNING
BOARD
VEHICLE
FRAME
FRONT
SCREW
910513CR
16. Install the left rear end cap to the left running board
with one self-tapping screw, one screw and one
6 mm flange nut.
LEFT RUNNING
BOARD
LEFT REAR
END CAP
6 mm
FLANGE
NUT
SCREW
2 BRACKETS B
SPRING NUT
(Reuse.)
8 FLANGE
BOLTS
SELF-TAPPING SCREW
included kit
910509AR
910510CR
17. Install the spring nut to the left rear end cap.
5 of 6
18. Get the left running board, and remove the wrapper
that secures the bolts to the running board. Align the
six bolts with to the six holes in brackets A and B.
While applying forward pressure on the left running
board, install it with six 8 mm flange nuts. Do not
tighten the flange nuts yet.
FRONT
BRACKET
LEFT RUNNING
BOARD
4
2 BRACKETS B
Left side
only.
Push up.
1
LEFT
RUNNING
BOARD
LEFT FRONT
END CAP
6 LEFT RUNNING
BOARD BOLTS
Make sure
there is no
gap in this
area.
4 SELF-TAPPING
SCREWS (Reuse.)
6 FLANGE
NUTS,
8 mm
910514BR
21. While holding the left front end cap against the left
front inner fender, tighten the self-tapping screws in
the order shown.
22. Torque all the flange bolts, and the 8 mm flange nuts
you installed to 27 Nm (20 lbfft).
910511BR
19. Secure the rear portion of the left running board with
the self-tapping screw removed in step 3.
23. Turn the steering wheel all the way clockwise, and
repeat steps 2 thru 22 to install the right running
board.
LEFT
RUNNING
BOARD
SELF-TAPPING
SCREW
(Reuse.)
6 of 6
910512AR