Professional Documents
Culture Documents
Operator Manual & Parts Catalog: Degelman Industries LTD
Operator Manual & Parts Catalog: Degelman Industries LTD
142628 v1.5
DEGELMAN
INDUSTRIES
L T D.
DEGELMAN.COM
STRAWMASTER 7000
30, 50, 62, 70 & 82
Safety
Safety Information
Operation
Overview / Preparation
Hook-Up
10
Height Adjustment
11
Transporting / Storage
12
Service 13
Repair 15
Troubleshooting
19
21
Warranty 44
DEGELMAN
INDUSTRIES
L T D.
IMPORTANT:
DEGELMAN.COM
READ MANUAL
Introduction
OPERATOR ORIENTATION - The directions left, right, front and rear, as mentioned throughout the manual,
are as seen from the tractor drivers seat and facing in the direction of travel.
Rear
Right
Side
Front
Left Side
(30-November-2012)
-1-
Safety
ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
SIGNAL WORDS
Note the use of the Signal Words: DANGER, WARNING, and CAUTION with the safety messages.
The appropriate Signal Word has been selected using the following guidelines:
DANGER
WARNING
CAUTION
(30-November-2012)
-2-
Safety
SAFETY
GENERAL SAFETY
A person who has not read and understood all operating and safety instructions
is not qualified to operate the machine. An
untrained operator exposes himself and bystanders to possible serious injury or death.
(30-November-2012)
-3-
Safety
OPERATING SAFETY
MAINTENANCE SAFETY
1. Review the Operators Manual and all safety
items before working with, maintaining or
operating the Strawmaster.
(30-November-2012)
-4-
Safety
HYDRAULIC SAFETY
TRANSPORT SAFETY
TIRE SAFETY
1. Failure to follow proper procedures when
mounting a tire on a wheel or rim can produce
a blow out which may result in serious injury or
death.
(30-November-2012)
-5-
Operation
TO THE NEW OPERATOR OR OWNER
PRINCIPLES OF OPERATION
The Strawmaster harrow sections consist of five
rows with ten tines per row which hold the straw.
As the tines drag along the ground, they
oscillate to build up a high
frequency vibration and
provide a shattering
action which breaks
up the straw allowing
the residue to be spread
evenly as it is released.
3
When stood vertically
the tines will rake flax
residue.
70 Strawmaster Model
1
5
2
4
6
(30-November-2012)
-6-
1. Trailer Frame
2. Latch Assembly
3. Swing Arm
4. Wing Beam
5. Centre Beam
6. Truss Beam
7. 10 Harrow Section
Operation
BREAK-IN
PRE-OPERATION CHECKLIST
It is important for both personal safety and
maintaining the good mechanical condition of
the machine that this pre-operational checklist be
followed.
Before operating the machine and each time thereafter, the following areas should be checked off:
A. Before using:
1. Read Safety Info. & Operators Manual.
2. Complete steps in Pre-Operation Checklist.
3. Lubricate all grease points.
4. Check all bolt tightness.
B. After operating for 2 hours:
30 model:
50 model:
62 model:
70 model:
82 model:
1. Repeat Step B.
2. Re-torque all bolts on harrow sections and
mounting brackets.
3. Go to the service schedule as outlined in the
Service & Maintenance section.
(30-November-2012)
OPERATING SAFETY
150 HP
200 HP
250 HP
300 HP
350 HP
100 HP
150 HP
175 HP
200 HP
300 HP
-7-
Operation - Hook-Up
HOOK-UP / UNHOOKING
The Strawmaster should always be parked on a
level, dry area that is free of debris and foreign
objects. Follow this procedure to hook-up:
1. Clear the area of bystanders and remove
foreign objects from the machine and working
area.
2. Make sure there is enough room to back the
tractor up to the trailer hitch.
3. Start the tractor and slowly back it up to the
hitch point.
4. Stop the tractor engine, place all controls in
neutral, set park brake and remove ignition key
before dismounting.
5. Use the trailer jack to raise or lower the hitch to
align with the drawbar.
6. Install a drawbar pin with provisions for a
mechanical retainer such as a KLIK pin.
Install the retainer.
7. Install a safety chain between the tractor and
the hitch.
8. Connect the hydraulics. To connect, proceed as
follows:
Use a clean cloth or paper towel to clean the
couplers on the ends of the hoses. Also clean
the area around the couplers on the tractor.
Remove the plastic plugs from the couplers and
insert the male ends.
Be sure to match the pressure and return line to
one valve bank.
9. Raise the hitch jack and rotate it 90 to place in
its stowed position.
10. When unhooking from the tractor, reverse the
above procedure.
(30-November-2012)
-8-
1
1. Remove frame transport pins and place in
holders. Both sides. (NOTE: Hydraulic models have
4
Remove
Remove
Store
Cylinder
Lock
The Auto-Fold
Cables should
be tight and
the latch in the
open position.
2. The 30 and 50 models have a telescopic truss
beam. Move out into field position and secure
with pin. All other models have a fixed length
truss arm.
Transport
Field
Transport
Transport Pin
Hair Pin
50
Field
30
(30-November-2012)
-9-
if machine leaves
clumps of straw,
apply slight down
pressure by
extending hydraulic
lift cylinders.
REMEMBER:
actual settings will vary with tine wear.
ensure trailer and frame are leveled properly.
(Refer to the Height Adjustment section.)
FIELD PACKING
1 2 3
RAKING
1 2 3
MACHINE PREPARATION
THE FIELD
Work the field at 45 degrees to the seeding line.
1 2 3
CHEMICAL INCORPORATION
TOUGH STRAW
Advance the tine angle to a more aggressive
setting. This will hold straw for a longer period
of time, allowing for a more even distribution of
residue. REMEMBER: Breaking down straw is much
more effective in dry conditions.
(30-November-2012)
1 2 3
-10-
(30-November-2012)
-11-
Fine Adjustment
Operation
TRANSPORT
STORAGE
Transport
Field
Transport Pin
Hair Pin
50
Field
30
TRANSPORT SAFETY
STORAGE SAFETY
(30-November-2012)
RIDERS
-12-
GREASING
Use an SAE multipurpose grease with extreme
pressure (EP) performance. Also acceptable is an
SAE multipurpose lithium base grease.
Dailly - 8 Hours
Hydraulic Fluid Leaks
Damaged Hoses
Cart/Trailer Tires:
MAINTENANCE SAFETY
Endwheel Tires:
Weekly - 25 Hours
Bolt Tightness
Wheel Bearings
Latch Mechanism
Cable Assembly
TORQUE
all hardware
Sidewind Jacks
Harrow Sections
(Manual adjustable models)
End Wheel
Cylinder (x2)
or Sidewind
Jack (x2)
Center Beam Pin
& Cross Joints (x2)
Hub - Trailer
Wheel (x2)
Hub-Transport
Wheel (2x)
Upper & lower
wheel plates (x2)
142628 - Strawmaster 7000
(30-November-2012)
-13-
Hub-End
Wheel (2x)
TORQUE
all hardware
Size
Grade 5
Grade 8
lb . ft (N . m) lb . ft (N . m)
1/4
5/16
3/8
7/16
1/2
9/16
5/8
3/4
7/8
1
9 (12)
18 (25)
33 (44)
52 (70)
80 (110)
115 (155)
160 (215)
280 (375)
450 (625)
675 (925)
12.5(17)
26 (35)
46 (63)
75 (100)
115 (150)
160 (225)
225 (300)
400 (550)
650 (875)
975 (1300)
Size
M6
M8
M10
M12
M14
M16
M18
M20
M22
M24
Class 8.8
Class 10.9
lb . ft (N . m) lb . ft (N . m)
8.5 (11)
20 (28)
40 (55)
70 (95)
110 (150)
175 (240)
250 (330)
350 (475)
475 (650)
600 (825)
5.8
SAE-2
SAE-5
12 (17)
30 (40)
60 (80)
105 (140)
165 (225)
255 (360)
350 (475)
500 (675)
675 (925)
850 (1150)
8.8
10.9
SAE-8
HARDWARE/HOSE SPECIFICATIONS
lb.ft (N.m)
1/2
3/4
7/8
34 (46)
75 (100)
90 (122)
(30-November-2012)
-14-
Lock Nuts
Spindle
DISASSEMBLY
Dust Seal
Inner Cone
Inner Cup
Hub
Outer Cup
Outer Cone
Washer
Slotted Nut
Cotter Pin
Dust Cap
ASSEMBLY
1. If cups need replacing, be
careful to install them gently
and evenly into hub until they
are fully seated.
Tire
Valve Stem
Rim
Wheel Bolts
(30-November-2012)
-15-
Endwheel Tires:
9.5L x15 - 6 PLY
-or 9.5L x15 - 8 PLY
DISASSEMBLY
1. Loosen lock ring and turn off end cap.
5. Turn end cap fully against lock ring then back off
end cap to align ports.
COMMON DEGELMAN
CYLINDER COMPONENTS
Piston
Barrel
Lock Nut
Lock Ring
O-ring
End Cap
Piston
Seals
(5 part)
O-ring
Wear Ring
Rod Seal
Rod Wiper Seal
Rod
Assembly
Shoulder Bolt
Flat Washer
(30-November-2012)
Pin
Assembly
-16-
DISASSEMBLY:
Link Bar
ASSEMBLY:
1. Slide the tines onto the pipe.
(Make sure all tines are
installed facing the same
direction)
Pipe Lug
Back Row
(30-November-2012)
-17-
Latch
Holder
Latch
Assembly
NOTE: Allow
minimal clearance
between swing
arm and latch.
Eye Bolt
Cable
Assembly
Swing Arm
Trailer frame
142438 - Strawmaster 7000 (2)
142383 - Caution, 6 Points (1)
142368 - Important, Install Pin (2)
142008 - Degelman - 6 x 25-3/4 (2)
143162 - Manual Holder Decal (1)
142279 - Reflector, Amber - 3-1/4 (2)
Auto-fold Arm
142439 - Important, Back-up Evenly (2)
142280 - Reflector, Red 6-1/4 (2)
142279 - Reflector, Amber - 3-1/4 (2)
Harrow Section Frame
142010 - Degelman, 2-3/4 x 12 (1)
(30-November-2012)
-18-
Troubleshooting
TROUBLESHOOTING
In the following section, we have listed some of the problems, causes and solutions that you may encounter. If
you encounter a problem that is difficult to solve, even after having read through this troubleshooting section,
please call your local dealer or distributor. Before you call, have this manual and the serial number from your
unit ready.
PROBLEM
CAUSE
SOLUTION
Restriction in hose.
Repair as needed.
Tighten or replace.
Auto-Fold unlatches
prematurely.
Oil accumulation on
cylinder shaft.
(30-November-2012)
-19-
General Overview
End Wheel
10 Harrow
Section
Transport
Wheel
Right
Truss Arm
Right Wing
Beam
Trailer Wheel
Center
Beam
Auto-Fold
Latch
Auto-Fold
Cylinder
Swing
Arm Pipe
Trailer
Cross Joint
Trailer Wheel
Auto-Fold Latch
Left Wing
Beam
Left Truss
Arm
30'
50'
62'
70'
82'
70 Strawmaster Shown
Manual Adjusment Option
30'
50'
70'
82'
(30-November-2012)
-20-
General Overview
20-21
22
23-24
25
26
27
28
29
30-32
32-34
35
35
38
42
Warranty 44
10 Harrow
Section
Transport
Wheel
IMPORTANT:
End Wheel
READ MANUAL
142628 - Strawmaster 7000
(30-November-2012)
-21-
82
70
62
50
243165 - Plate,
End Wheel (2)
30
82
70
82
62
Field
243341 - Truss
Slider 50 (1)
50
243837 - Truss
Slider 30 (1)
30
Field
(30-November-2012)
-22-
Trailer Components
143162 - Decal,
Manual Holder (1)
(30-November-2012)
-23-
243200 - Swing
Arm Pipe (2)
ace
142279 - Reflector,
Amber - 3-1/4 (2)
ts f
(por
122733 - Cylinder,
Auto-fold - 3-1/2
x 31x 2 (2)
(see below for
details)
n)
dow
142368 - Decal,
Important-Install Pin (2)
82
243002 - Jack
Mount (1)
112
NOTE: Jack mount assembly must be installed
before installing the harrow sections.
(30-November-2012)
-24-
Auto-Fold Latch
Insert the swing arm pipe into socket.
Rotate the pipe forward so it connects with the centre
of the slot on the latch.
ch
Lat
Arm
You might have to move the latch arm back & forth in
the slotted bolt holes to align.
The swing arm should strike the ramp plate of the
latch holder at least half way up. If it doesnt hit the
ramp at the proper point pull it up with an
overhead crane and check it again.
Swing Arm
Pipe
Socket
142439 - Decal,
Important-Back-up
Evenly (1)
142280 - Reflector,
Red 6-1/4 (this side) (1)
142279 - Reflector,
Amber - 3-1/4
(shown) (1)
143034 - Spring, Compression - 4 (1)
118512 - Flat washer, 1/2 (1)
118628 - Bolt, 1/2 x 5-1/2 (1)
(30-November-2012)
-25-
Hydraulic
Adjustment Models
243843 - Rock shaft (1)
(Hyd. Adj Models)
122760 - Cylinder, Trailer wheel 3x 8x 1-5/8 (2)
(see below for details)
TIRE PRESSURE
Cart/Trailer Tires:
16.5L x16.1 - 6 PLY
48 PSI (330 kPa)
122760 - 3 x 8 x 1-5/8
123336 - Piston,
Unitised (1)
118441 - Lock
nut, 7/8 UNF
Unitorque (1)
122740 - 3 x 8 x 1-5/8
123336 - Piston,
Unitised (1)
118441 - Lock
nut, 7/8 UNF
Unitorque (1)
(03-April-2013)
-26-
117129 - Wear
bushing (1)
118126 - Bolt,
1/2 x 4 (2)
(03-April-2013)
-27-
30
82
70
62
50
30
(30-November-2012)
-28-
62
50
30
82
TIRE PRESSURES
Transport Tires (70, 62, 50, 30):
9.5L x15 - 6 PLY 36 PSI (248 kPa)
-or9.5L x15 - 8 PLY 60 PSI (414 kPa)
Tire
Rim, 6 Bolt
Valve Stem
118835 - Cotter
pin, 1/2 (1)
(30-November-2012)
-29-
243180 - Axle
holder (1)
243175 - Plate,
Lower (1)
243164 - Ring,
Retaining (4)
243187 - Pin,
4-5/8 (2)
244760 - Endwheel,
Upper Assembly (1)
(for Hydraulic option)
244342 - Endwheel,
Upper Assembly
(for Hydraulic option)
118972 - Jam
Nut, 1-1/4 (2)
244765 - Adjustment
Rod, 1-1/2 (1)
244347 - Upper
Endwheel Plate (1)
Note: Models prior to Oct. 2010
(Serial #s 5979 and lower) use a
different Trailer Wheel Cylinder
(122740 - p.26) and require a different
assembly for the endwheel upper plate:
118451 - Jam
Nut, 1-1/2 (2)
244761 - Upper
Endwheel Plate (1)
(22-May-2013)
-30-
Rim, 6 Bolt
Valve Stem
118914 - Wheel bolt, 9/16 x 1-3/4 UNF (6)
243163 - SMV
Sign Holder (1)
(30-November-2012)
-31-
142135 - SMV
Sign (1)
50'
62'
70'
82'
48
19-3/4
(Typical)
72
72 or 24
(24 for 62 & 82 models only)
30'
50'
70'
82'
10 Harrow Section
6 Harrow Section
(30-November-2012)
-32-
TINE OPTIONS
QUANTITY OF TINES REQUIRED
30
50
62
70
82
75 125 155 175 205
(10 Section - 25 tines)
(6 Section - 15 tines)
STANDARD OPTIONS
143112 - 9/16 Straight Tine (1)
143113 - 5/8 Straight Tine (1)
OTHER OPTIONS
143501 - 5/8 Straight Tine - wear tip (1)
(Call for Availability)
143110 - 9/16 Curved Tine (1)
(Call for Availability)
(30-November-2012)
-33-
14 3/4
244017 - Indicator
pointer (1)
(30-November-2012)
-34-
Barrel
Lock Ring
Open Cap
Piston,
Unitised
Lock Nut
Seal Kit
Degelman
Cylinder#
Monarch
Cylinder#
Hydraulic Cylinder
Description
123225
122120
2-1/2 x 8 x 1-1/8 R
123226
122130
2-3/4 x 8 x 1-1/8 R
122830
122140
122836
122150
3-1/4 x 8 x 1-1/4 R
122850
122160
3-1/2 x 8 x 1-1/4 R
123258
122170
3-3/4 x 8 x 1-3/8 R
123275
122180
123278
122190
4-1/4 x 8 x 1-1/2 R
123300
122195
4-1/2 x 8 x 1-1/2 R
x 8 x 1-1/4 R
x 8 x 1-3/8 R
Degelman
Cylinder#
Hydraulic Cylinder
Description
Barrel
123225
2-1/2 x 8 x 1-1/8 R
123234
123267
123253
123259
123226
2-3/4 x 8 x 1-1/8 R
123284
123267
123294
123290
122830
Piston
x 8 x 1-1/4 R
122832
122085
122799
122558
122836
3-1/4 x 8 x 1-1/4 R
122838
122085
122840
122842
122850
3-1/2 x 8 x 1-1/4 R
122852
122834
122856
122858
123258
3-3/4 x 8 x 1-3/8 R
123306
123307
123313
123315
x 8 x 1-3/8 R
123317
123307
123321
123319
123278
4-1/4 x 8 x 1-1/2 R
123323
123325
123329
123327
123300
4-1/2 x 8 x 1-1/2 R
123331
123325
123333
123335
123275
Optional Accessories
PLATFORM FOR VALMAR
- Platform
- Lock Nut
- Bolt
- Clamp
(30-November-2012)
-35-
174
140
86
52
2
3
(2)
183
183
140
52
Models withHydraulic
Lift and Rephasing
Cylinders
use three-clip here
(30-November-2012)
174
ith
els w linders
d
o
y
M
C
e
r
g
sin clip he
pha
Re e three
us
-36-
86
Hydraulic Fittings
1
(2)
(2)
(2)
(6)
Common Hoses
186
311
98
7 Two-Hose
Clip Positions
2
3
11 Two-Hose
Clip Positions
50`
118915 - Screw,
Self-Tap - 5/16
x 1- 3/4 (1)
16 Two-Hose
Clip Positions
A
B
C
A
B
C
30 198 (2) 168 (1) 228 (1)
50 318 (2) 288 (1) 348 (1)
62 390 (2) 360 (1) 420 (1)
70 436 (2) 408 (1) 466 (1)
82 510 (2) 480 (1) 540 (1)
30`
62`
186
17 Two-Hose
Clip Positions
70`
23 Two-Hose
Clip Positions
243853 - Three-clip
holder used here
(3), see Autofold
Cylinder page for
mounting hardware.
186
311
Trailer Wheel
Cylinder (2)
4
A
5
4
4
B
4
3
(30-November-2012)
82`
End Wheel
Cylinder (2)
5
-37-
Rephasing Cylinders
Monarch
Cylinder#
Hydraulic Cylinder
Description
123225
122120
2-1/2 x 8 x 1-1/8 R
123226
122130
2-3/4 x 8 x 1-1/8 R
122830
122140
3 x 8 x 1-1/4 R
122836
122150
3-1/4 x 8 x 1-1/4 R
122850
122160
3-1/2 x 8 x 1-1/4 R
123258
122170
3-3/4 x 8 x 1-3/8 R
123275
122180
4 x 8 x 1-3/8 R
30ft
50ft
62ft
Hydraulic Fittings
1
2
3
Centered
36
2-1/2
466
Hydraulic Hoses
30ft
6
1
2-1/2
588
50ft
2-1/2
6
2
258
2-3/4
660
6
6
2
2-1/2
(30-November-2012)
-38-
258
6
2
2-3/4
62ft
212
Hose Clamps
Install hose support
rings on the outside
of the center beams
cylinder lugs.
Install hose
clamps
behind the
cast shank
bolt bar.
5
1
Hose Clips
650256 - Hose clip, two-hose
243850 - Hose
Support Ring (2)
Self-Tap Mount
2-3/4
30ft
6
1
Stud Mounted
288
Self-Tap Mount
528
6
300
648
6
1
3-1/4
288
118915 - Screw,
Self-Tapping
5/16x1- 3/4
50ft
6
2
3-1/2
300
258
720
258
(30-November-2012)
62ft
6
2
258
-39-
288
3-3/4
3-1/4
3-1/2
258
70ft
1
2
82ft
Hydraulic Hoses
Rephasing Cylinders
Degelman
Cylinder#
Monarch
Cylinder#
Hydraulic Cylinder
Description
123225
122120
2-1/2 x 8 x 1-1/8 R
123226
122130
2-3/4 x 8 x 1-1/8 R
122830
122140
3 x 8 x 1-1/4 R
122836
122150
3-1/4 x 8 x 1-1/4 R
122850
122160
3-1/2 x 8 x 1-1/4 R
123258
122170
3-3/4 x 8 x 1-3/8 R
123275
122180
4 x 8 x 1-3/8 R
123278
122190
4-1/4 x 8 x 1-1/2 R
123300
122195
4-1/2 x 8 x 1-1/2 R
Centered
36
2-1/2
708
4
2-3/4
2-1/2
3 258
70ft
3 258
3
82ft
780
2-1/2
3
3
(30-November-2012)
6
2
3 258
6
2
3 258
3
-40-
3-1/4
6
2
2-3/4
3 212
3
Hose Clamps
Install hose support
rings on the outside
of the center beams
cylinder lugs.
Install hose
clamps
behind the
cast shank
bolt bar.
1
2
2
3
Hose Clips
650256 - Hose clip, two-hose
243850 - Hose
Support Ring (2)
Self-Tap Mount
Self-Tap Mount
Stud Mounted
118915 - Screw,
Self-Tapping
5/16x1- 3/4
6 Self-Tap Mount
768
6
2
3 288
3
3 300
3
70ft
3258
3-1/2
3-1/4
3-3/4
3 258
3
82ft
840
3 258
3
(30-November-2012)
3 258
3
-41-
6
2
6
2
3 258
3
4-1/2
4-1/4
3 288
6
2
3-1/2
6
1
3-3/4
6
2
3 258
3
7 POLE PLUG
WHITE
7 POLE PLUG
BROWN
GREEN - GREEN
WHITE - BLACK
WHITE
YELLOW BROWNGREEN
YELLOW
TO J-BOX
TO J-BOX
BROWN - RED
GREEN - GREEN
YELLOW - WHITE
WHITE - BLACK
BROWN - RED
GREEN
YELLOW - WHITE
Note: Twist and solder all ends before inserting into terminal. If more than one wire goes into a terminal - twist together
CONNECT
# TO
TERMINAL
BLOCK #
and
solder toWIRE
prevent
fraying.
(Use 60% tin 40% lead rosin solder.)
GREEN #6
TO RH TAIL LIGHT
1
2
3
4
5
BLACK #2
RED #3
GREEN #1
WHITE #4
BLACK #2
RED #3
WHITE #4
light)(1)
(Redbox
- BROWN
WHITE
(Amber light)
- RED
129033GREEN
- Straight
BLACK - WHITE
Cord Connector
(3) (Ground)
RH FROM J-BOX
light)
(Amber
- RED (Red
GREEN
light)
- BROWN
WHITE
LH FROM J-BOX
9
BLACK SPLICE #7
6
7
6 8
9
7
10
8
9
10
SPLICE
WHITE
#6 #8
GREEN
BLACK SPLICE #7
GREEN
#8 #9
WHITE SPLICE
SPLICE
WHITE
#9 #8
GREEN
BLACK SPLICE #7
RH LIGHT PLUG
LH LIGHT 118717
PLUG - Lock Nut, 1/2 NPT (3)
Wire,16/3 Super VU - LH (1)
244123 - 59ft (82ft SM)
244114 - 53ft (70ft SM)
244126 - 48ft (62ft SM)
244113 - 42ft (50ft SM)
244112 - 32ft (30ft SM)
LH LIGHT PLUG
7 POLE PLUG
BROWN
Tie to Hydraulic
Hoses, 3 Places
YELLOW
118735 - Screw,
1/4-20 x 3/4 (6)
WHITE - BLACK
BROWN - RED
GREEN
YELLOW - WHITE
Tailight
CONNECT Wiring
WIRE # TO TERMINAL BLOCK #
244108 - Split
Loom, 3/8 x
39-1/2 (2)
Connection
GREEN #1
BLACK #2
RED #3
WHITE #4
RH FROM J-BOX
1
2
3
4
5
6
7
8
9
10
LH FROM J-BOX
GREEN #9
BLACK SPLICE #7
WHITE SPLICE #8
RH LIGHT PLUG
-42-
TO RH TAIL LIGHT
WHITE SPLICE #8
GREEN #6
BLACK SPLICE #7
129043 - Crimp,
Butt Splice - 16
gauge (6)
TO LH TAIL LIGHT
RH LIGHT PLUG
FromGREEN
7 WHITE
(Red light)
- BROWN
(Amber light)
- RED
Pole Plug
WHITE
Tie
TO LH TAIL LIGHT
BLACK SPLICE #7
Tie
TO RH TAIL LIGHT
WHITE SPLICE #8
RH FROM J-BOX
Tie
LH FROM J-BOX
1
2
3
4
5
LH LIGHT PLUG
TO LH TAIL LIGHT
7 POLE PLUG
7 Pole
Plug
WHITE
BROWN
Tail/Running
Ground
2
7
3
4
GREEN
Right High FL
Clip on top
1-1/4
of beam
with rubber
cushion
clamp.
Left High FL
Splice - White/Brown
Wiring Plug
Connection
2-3/4
YELLOW
2-1/2
2-1/2
Grommet
5/8x 5/8
Connectors-LH
A - White
B - Yellow
C - Brown
Connectors-RH
A - White
B - Green
C - Brown
244590 - Dual
Lamp (LH) (1)
244591 - Dual
Lamp (RH) (1)
Tie to hold
loom closed
Tie
Tie
Grommet
3/8x 1/4
(30-November-2012)
-43-
Tie to hold
loom closed
Amber
Tie
Warranty
2 Year
(30-November-2012)
-44-
Warranty
WARRANTY INFORMATION
Make certain the warranty registration card has been forwarded to:
Always give your dealer the serial number of your Degelman product when ordering parts or requesting
service or other information.
The serial number is located on the machine as shown in the diagram below. In the space provided record the
model number, the serial number and the date of purchase to assist your dealer in providing you with prompt
and efficient service.
SERIAL NUMBER:
MODEL NUMBER:
DATE OF PURCHASE:
(30-November-2012)
-45-
Serial Number
Plate Location