Professional Documents
Culture Documents
4W Dual-Pump: General Description Features
4W Dual-Pump: General Description Features
FEATURES
APPLICATIONS
Portable Speakers
MID
Mobile Phones
VDD
C F1 2.2uF C F2 2.2uF
Cs
10uF
APPLICATION CIRCUIT
CN2
COUT
AVDD
PVOUT
Cs
1uF
PVDD
H
EN
10uF
100uF
ft2820
PGND
VOP
INP
Cin 470nF
VON
INN
Cin 470nF
GND(AGND/CGND)
www.fangtek.com.cn
ft2820
PIN CONFIGURATION AND DESCRIPTION
CGND
20
CN1
AGND
19
PVOUT
EN
18
CP1
CN2
17
PVDD
CP2
16
VOP
CVDD
15
PGND
NC
14
VON
INN
13
PVDD
INP
12
NC
10
11
NC
AVDD
PIN NUMBER
I/O
DESCRIPTION
EN
CN2
CP2
CVDD
INN
INP
AVDD
10
PVDD
13, 17
VON
14
PGND
15
VOP
16
CP1
18
PVOUT
19
Power supply rail for the Class-D amplifier output stage. It must be
externally shorted to PVOUT.
CN1
20
CGND
AGND
Analog ground.
7, 11, 12
No internal connection.
NC
ORDERING INFORMATION
PART NUMBER
TEMPERATURE RANGE
PACKAGE
ft2820P
-40C to +85C
TSSOP-20L
SEP, 2013
http://www.fangtek.com.cn
ft2820
ABSOLUTE MAXIMUM RATINGS (Note 1)
PARAMETER
VALUE
-0.3V to 5.5V
-0.3V to 6.5V
-0.3V to VDD+0.3V
Internally Limited
2000V
-40C to +150C
260C
Storage Temperature
-45C to +150C
Note 1: Stresses beyond those listed under absolute maximun ratings may cause permanent damage to the device. These are stress
ratings only,and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
TA < +25C
TA = +70C
TA = +85C
JA
TSSOP-20L
4.8W
3.1W
2.6W
26C/W
Note 2: The thermal pad of the package mus be directly soldered onto a grounded metal island (as a thermal sink) on the system board.
Note 3: The power disspation ratings are for a two-side, two-plane printed circuit board (PCB).
CONDITIONS
AVDD, CVDD
MIN
TYP
MAX
UNIT
3.0
5.5
-40
85
3.2
SEP, 2013
http://www.fangtek.com.cn
ft2820
FUNCTIONAL BLOCK DIAGRAM
AVDD
CP1
CVDD
CN1
CP2
CN2
PVOUT
Oscillator
Charge-Pump
PVDD
VOP
INP
INN
Input
Buffer
Class-D
Modulator
Output
Stage
VON
PVDD
ALC Mode
Control
OCP
EN
Shutdown
Control
OTP
GND(AGND/CGND)
PGND
UVLO
SEP, 2013
http://www.fangtek.com.cn
ft2820
ELECTRICAL CHARACTERISTICS
VDD=3.6V, Mode 1, CAVDD=1 F, CCVDD=10 F, CF1=CF2 =2.2 F, COUT=10 F//100uF, f=1kHz,
CIN=470nF, RL=4+33 H, TA=25C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VDD
Supply Voltage
AVDD, CVDD
3.0
5.5
VUVLOUP
2.2
VUVLODN
2.0
IDD
EN High, VDD=3.6V
2.7
mA
EN High, VDD=5.0V
3.0
mA
ISD
Shutdown Current
0.1
VIN
VIL
TOTSD
Over-Temperature Threshold
160
THYS
Over-Temperature Hysteresis
20
PO=0.5W
82
Power Efficiency
PO=2.0W
72
1.2
V
0.4
CHARGE PUMP
PVOUT
IPVDD=100mA
IOUT
VDD=4.2V
TPRECH
Pre-charge time
COUT=10F//100uF
TSS
Soft-start Time
fPUMP
5.7
6.0
6.3
1.0
ms
500
MHz
CLASS-G AMPLIFIER
Maximum Output Power
THD+N=10%, VDD=4.2V
2.6
THD+N=10%, VDD=3.6V
2.4
THD+N=1%, VDD=4.2V
2.1
THD+N=1%, VDD=3.6V
2.0
THD+N=10%, VDD=4.2V
4.0
THD+N=10%, VDD=3.6V
3.5
THD+N=1%, VDD=4.2V
3.4
THD+N=1%, VDD=3.6V
3.0
Vin=300mVRMS, VDD=4.2V
2.0
Vin=300mVRMS, VDD=3.6V
1.9
Vin=300mVRMS, VDD=4.2V
3.3
Vin=300mVRMS, VDD=3.6V
2.9
27.6
24.1
24.1
Load=8+33H
(Mode 3, ALC Off)
PO, MAX
W
Maximum Output Power
Load=4+33H
(Mode 3, ALC Off)
Constant Output Power
Load=8+33H
PO, ALC
Load=4+33H
(Mode 1 & 2, ALC On)
AV
SEP, 2013
http://www.fangtek.com.cn
dB
ft2820
ELECTRICAL CHARACTERISTICS (Contd)
VDD=3.6V, Mode 1, CAVDD=1 F, CCVDD=10 F, CF1=CF2 =2.2 F, COUT=10 F//100uF, f=1kHz,
CIN=470nF, RL=4+33 H, TA=25C, unless otherwise specified.
SYMBOL
PARAMETER
ZIN
ZO
EN Low
PO=1.0W
0.05
PO=2.0W
0.06
VDD=3.6V, PO=2.9W
0.4
VDD=4.2V, PO=3.3W
0.5
VOS
mV
VN
f=20Hz ~ 20kHz
Inputs AC-Grounded, AV=27.6dB
185
VRMS
PSRR
75
70
CMRR
70
dB
SNR
Signal-To-Noise Ratio
85
dB
fPWM
VDD=3.6V
MHz
TSTUP
Startup Time
VDD=3.6V
32
ms
ILIMIT
Over-Current Limit
2.0
THICCUP
200
ms
AMAX
10.5
dB
TATT
32
ms
TREL
2.0
THD+N
TEST CONDITIONS
MIN
TYP
MAX
UNIT
24
dB
ALC
EN CONTROL
TLO
Time of EN Low
0.5
THI
Time of EN High
0.5
TRST
50
TSHDN
10
s
s
500
s
ms
Note:
(1)
A 33H inductor was placed in series with the load resistor to emulate a small speaker for efficiency measurements.
(2)
The 33kHz lowpass filter is required even if the analyzer has an internal lowpass filter. An RC lowpass filter (100 , 47nF) is used on each
SEP, 2013
http://www.fangtek.com.cn
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS
List of Performance Characteristics
CF1=CF2=2.2 F, COUT=10 F//100uF, CAVDD=1 F, CCVDD=10F, CIN=470nF, f=1kHz, TA=25C, unless
otherwise specified.
CONDITIONS
DESCRIPTION
Constant Output Power vs. Supply Voltage
Maximum
Output
Power
vs.
Voltage
FIGURE
Mode 1
Mode 2
Mode 3
Mode 4
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Charge Pump Mode Transition Waveforms VDD=4.2V, Vin=50mVRMS ~100mVRMS, RL=4+33H, Mode 1
36
37
38
SEP, 2013
http://www.fangtek.com.cn
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
Constant Output Power vs. Supply Voltage
3.5
3.5
3
2.5
2
1.5
RL=8+33uH,Vin=0.3Vrms,Mode 1 (ALC On)
RL=4+33uH,Vin=0.3Vrms,Mode 1 (ALC On)
1
0.5
3
2.5
2
1.5
RL=8+33uH,Vin=0.45Vrms,Mode 2 (ALC On)
RL=4+33uH,Vin=0.45Vrms,Mode 2 (ALC On)
1
0.5
0
3
3.5
4
4.5
Supply Voltage (V)
5.5
3.5
4
4.5
Supply Voltage (V)
5.5
Figure 3: Constant Output Power vs. Supply Voltage Figure 4: Constant Output Power vs. Supply Voltage
2.5
4
2
1.5
1
RL=8+33uH,THD+N=1%,Mode 3 (ALC Off)
RL=8+33uH,THD+N=10%,Mode 3 (ALC Off)
0.5
3
2
RL=4+33uH,THD+N=1%,Mode 3 (ALC Off)
RL=4+33uH,THD+N=10%,Mode 3 (ALC Off)
1
0
0
3
3.5
4
4.5
Supply Voltage (V)
5.5
3.5
5.5
10000
10000
1000
1000
4
4.5
Supply Voltage (V)
100
10
100
10
VDD=3.6V,RL=8+33H,Mode 2 (ALC On)
1
10
100
1000
Input Voltage (mVrms)
10000
SEP, 2013
10
100
1000
Input Voltage (mVrms)
10000
http://www.fangtek.com.cn
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
10000
10000
1000
1000
100
10
100
10
VDD=4.2V,RL=8+33H,Mode 2 (ALC On)
1
10
100
1000
Input Voltage (mVrms)
10000
10
10000
10000
1000
1000
10000
100
10
100
10
1
10
100
1000
Input Voltage (mVrms)
10000
10
100
1000
Input Voltage (mVrms)
10000
10000
10000
1000
1000
100
1000
Input Voltage (mVrms)
100
10
100
10
10
100
1000
Input Voltage (mVrms)
10000
SEP, 2013
10
100
1000
Input Voltage (mVrms)
10000
http://www.fangtek.com.cn
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
1000
1000
800
600
400
200
0
800
600
400
200
0
3.5
4
4.5
Supply Voltage (V)
5.5
3.5
4
4.5
Supply Voltage (V)
5.5
2000
3000
1600
1800
1400
1200
1000
800
600
400
VDD=3.6V,RL=8+33H,Mode 1
VDD=4.2V,RL=8+33H,Mode 1
200
2500
2000
1500
1000
500
VDD=3.6V,RL=4+33H,Mode 1
VDD=4.2V,RL=4+33H,Mode 1
0
0
500
1000
1500
2000
Output Power (mW)
2500
3000
500
1000
1500 2000
2500 3000
Output Power (mW)
3500
4000
4500
100
90
90
80
80
70
70
Efficient (%)
Efficient (%)
100
60
50
40
30
VDD=3.6V,RL=8+33H,Mode 1
VDD=4.2V,RL=8+33H,Mode 1
20
10
60
50
40
30
20
VDD=3.6V,RL=4+33H,Mode 1
VDD=4.2V,RL=4+33H,Mode 1
10
0
0
500
1000
1500
2000
Output Power (mW)
2500
SEP, 2013
3000
500
1000
1500
2000
2500
Output Power (mW)
3000
3500
4000
http://www.fangtek.com.cn
10
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
100
100
VDD=3.6V, RL=4+33H, Mode 3
THD+N (%)
10
0.1
0.1
0.01
0.01
10
100
1000
10000
10
100
THD+N (%)
10
THD+N (%)
10000
100
0.1
0.1
0.01
0.01
10
100
1000
Input Voltage (mVrms)
10
10000
100
1000
Input Voltage (mVrms)
10000
100
VDD=3.6V, RL=8+33H, Mode 2
THD+N (%)
10
THD+N (%)
1000
Output Power (mW)
0.1
0.1
0.01
0.01
10
100
1000
Input Voltage (mVrms)
SEP, 2013
10000
10
100
1000
Input Voltage (mVrms)
10000
http://www.fangtek.com.cn
11
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
100
THD+N (%)
10
0.1
0.1
0.01
0.01
10
100
1000
Input Frequency (Hz)
10000
100000
10
100
100000
100
10
THD+N (%)
10000
0.1
0.1
0.01
10
100
1000
Input Frequency (Hz)
10000
0.01
100000
10
1000
10000
100000
-10
-10
VDD=3.6V, RL=8+33uH, Input-AC-Grounded, Mode 1
VDD=4.2V, RL=8+33uH, Input-AC-Grounded, Mode 1
-20
100
-20
-30
PSRR (dB)
-30
PSRR (dB)
1000
Input Frequency (Hz)
-40
-50
-40
-50
-60
-60
-70
-70
-80
-80
-90
-90
10
100
1000
Input Frequency (Hz)
10000
100000
SEP, 2013
10
100
1000
Input Frequency (Hz)
10000
100000
http://www.fangtek.com.cn
12
ft2820
TYPICAL PERFORMANCE CHARACTERISTICS (Contd)
7
6
5
4
3
X: 5ms/div
2
No Load, Input AC-Ground, Mode 1
1
0
3.00
3.50
4.00
4.50
Supply Voltage (V)
5.00
5.50
Y: 2V/div
PVDD=4.2~6.0V
Vin = 50mVRMS ~ 100mVRMS, 1kHz
X: 0.5s/div
X: 0.2s/div
X: 0.5s/div
Y: 2V/div
Y: 1V/div
VDD=4.2V, RL=4+33 H
EN, 1V/div
VDD=4.2V, RL=4+33 H
EN, 1V/div
X: 5ms/div
VOP-VON (33kHz Lowpass Filer)
Y: 2V/div
SEP, 2013
Y: 2V/div
http://www.fangtek.com.cn
13
ft2820
APPLICATION INFORMATION
The ft2820 is a 4W boosted Class-G audio power amplifier based upon a proprietary Dual-PumpTM
topology with automatic level control (ALC). It operates from 3V to 5.5V supply. When operating with a
4.2V supply voltage, it is capable of driving a 4 speaker load at a continuous average output of 4W with
10% THD+N. Its high efficiency, up to 82%, helps extend battery life for portable device applications.
In ft2820, the power supply rail of the amplifier output stage is internally boosted and regulated at 6V by
an integrated adaptive charge pump based upon the Dual-PumpTM topology, thus allowing for a much
louder audio output than a stand-alone one directly connected to the battery. It makes ft2820 an ideal
audio solution for portable devices, which are powered by a single-cell lithium battery while requiring
higher audio loudness.
The ft2820 also features ALC on the output signals, which detects the output clipping caused by the
over-level input signal and automatically adjusts the dynamic range of the output signals to prevent the
distortion of the audio signal. The ALC also eliminates the output clipping due to low battery supply
voltage.
As specifically designed for portable device applications, the ft2820 incorporates a shutdown mode to
minimize the power consumption by holding the EN pin to ground. It also includes comprehensive
protection features against various operating faults such as over-current, short-circuit, over-temperature,
and under-voltage for a safe and reliable operation.
DUAL-PUMPTM TECHNOLOGY
In order to maximize the output power, the ft2820 employs a proprietary Dual-PumpTM topology for the
internal charge pump using two flying capacitors to boost the supply voltage to a higher value at 6V. To
limit the inrush current to an acceptable value when the supply voltage is first applied to the device, the
charge pump incorporates soft-start function. Furthermore, when a short-circuit condition at the boosted
voltage is detected, the ft2820 limits the charging current to about 100mA for a safe operation.
Compared with a conventional charge pump topology using a single flying capacitor, the output current
capability of the Dual-PumpTM can be largely enhanced and the output voltage ripples minimized. In this
manner, the performance of the Class-G amplifier can be significantly improved, particularly for the
speakers whose impedance is less than 6. With the Dual-PumpTM topology, the ft2820 can deliver up to
4W into a 4 speaker load with 10% THD+N when powered by a single-cell lithium battery.
SEP, 2013
http://www.fangtek.com.cn
14
ft2820
Selection of Charge Pump Flying Capacitors (CF1 & CF2)
A nominal value of 2.2F is recommended for the flying capacitors (CF1 and CF2) of the charge pump, but
other values can be used. A low equivalent-series-resistance (ESR) ceramic capacitor, such as X7R or
X5R, is recommended.
T HI > 0.5us
T LO
0.5us < T LO < 10us
T RST
T SHDN
EN
L
MODE 1
ALC ON
AV=27.6dB
MODE 2
MODE 3
MODE 1
ALC ON
ALC OFF ALC ON
AV=24.1dB AV=24.1dB AV=27.6dB
MODE 1
ALC ON
SHUTDOWN
AV=27.6dB
SEP, 2013
http://www.fangtek.com.cn
15
ft2820
Mode
# of Pulses
Voltage Gain
ALC Function
Mode 1
27.6dB (24X)
Enable
Mode 2
24.1dB (16X)
Enable
Mode 3
24.1dB (16X)
Disable
Shutdown Mode
When the EN pin is held low for 5ms (typical) or longer, the ft2820 will be forced into the shutdown mode.
During the shutdown mode, the supply current will be significantly reduced to less than 1A.
Attack Time
Release Time
SEP, 2013
http://www.fangtek.com.cn
16
ft2820
The attack time is defined as the time interval required for the gain to fall to its steady-state gain less 3dB
approximately, presumed that a sufficiently large input signal is applied. The release time is the time
interval required for the amplifier to exit out of the present mode of operation. See Table 2.
Mode
32
2.0
Click-and-Pop Suppression
The ft2820 audio power amplifier features comprehensive click-and-pop suppression. During startup, the
click-and-pop suppression circuitry reduces any audible transients internal to the device. When entering
into shutdown, the differential audio outputs are pulled to ground through their individual internal resistors
(2K) simultaneously.
PSRR Enhancement
Without a dedicated pin for the common-mode voltage bias and an external holding capacitor onto the pin,
the ft2820 achieves a high PSRR, 75dB at 217Hz, thanks to a proprietary design technique.
PROTECTION MODES
The ft2820 incorporates various protection functions against possible operating faults for a safe operation.
It includes Under-voltage Lockout (UVLO), Over-Current Protection (OCP), and Over-Temperature
Shutdown (OTSD).
http://www.fangtek.com.cn
17
ft2820
Over-Temperature Shutdown (OTSD)
When the die temperature exceeds a preset threshold (160C), the device enters into the
over-temperature shutdown mode, where two differential outputs are pulled to ground through an
internal resistor (2K) individually. The device will resume normal operation once the die
temperature returns to a lower temperature, which is about 20C lower than the threshold.
Filterless Design
Traditional Class D amplifiers require an output filter to recover the audio signal from the amplifiers output.
The filter adds cost, increases the solution size of the amplifier, and can decrease efficiency and THD+N
performance. The traditional PWM scheme uses large differential output swings (twice of supply voltage
peak-to-peak) and causes large ripple currents. Any parasitic resistance in the filter components results in
loss of power and lowers the efficiency.
The ft2820 does not require an output filter. The device relies on the inherent inductance of the speaker
coil and the natural filtering of both the speaker and the human ear to recover the audio component of the
square-wave output. By eliminating the output filter, a smaller, less costly, and more efficient solution can
be accomplished.
Because the frequency of the ft2820 output is well beyond the bandwidth of most speakers, voice coil
movement due to the square-wave frequency is very small. Although this movement is small, a speaker
SEP, 2013
http://www.fangtek.com.cn
18
ft2820
not designed to handle the additional power can be damaged. For optimum results, use a speaker with a
series inductance greater than 10uH. Typical 8 speakers exhibit series inductances in the range from
20uH to 100uH.
EMI Reduction
The ft2820 does not require an LC output filter for short connections from the amplifier to the speaker.
However, additional EMI suppressions can be made by use of a ferrite bead in conjunction with a
capacitor, as shown in Figure 41. Choose a ferrite bead with low DC resistance (DCR) and high
impedance (100 ~ 220) at high frequencies (>100MHz). The current flowing through the ferrite bead
must be also taken into consideration. The effectiveness of ferrites can be greatly aggravated at much
lower than the rated current values. Choose a ferrite bead with a rated current value no less than 2A. The
capacitor value varies based on the ferrite bead chosen and the actual speaker lead length. Choose a
capacitor less than 1nF based on EMI performance
Ferrite
Chip Bead
VOP
FB1 220/2A
C1
1nF
Ferrite
Chip Bead
VON
FB2 220/2A
C2
1nF
http://www.fangtek.com.cn
19
ft2820
input resistors connected to INP or INN pin. However, for applications where additional gain adjustment
becomes necessary, a set of external input resistors can be added onto INP and INN pins respectively, as
shown in Figure 45. The value of the external input resistors must be included for the calculation of the
overall voltage gain (as described in Equation 1) as well as the selection of proper input capacitors (as
described in Equation 2). As shown in Equation 1, the external input resistors will attenuate the original
overall voltage gain by the ratio of RINTERNAL / (RIN+RINTERNAL).
AV = AV0 x [RINTERNAL / (RIN+RINTERNAL)]
Where
(1)
(2)
RINTERNAL = 24K
Choose CIN such that the fC is well below the lowest frequency of interest. Setting fC too high affects the
low frequency responses of the amplifier. Consider an example where the specification calls for AV=28dB
and a flat frequency response down to 20Hz. In this example, RIN=0K and CIN is calculated to be
0.33F.
Note that any mismatch in capacitance between two audio inputs will cause a mismatch in the corner
frequencies. Severe mismatch may also cause turn-on pop noise, PSRR, CMRR performance. Choose
capacitors with a tolerance of 5% or better.
Furthermore, the type of the input capacitor is crucial to audio quality. For best audio quality, use
capacitors whose dielectrics have low-voltage coefficients, such as tantalum or aluminum electrolytic.
Capacitors with high-voltage coefficients, such as ceramics, may result in increased distortion at low
frequencies.
SEP, 2013
http://www.fangtek.com.cn
20
ft2820
EMI The ferrite EMI filters should be placed as close to the output terminals as possible for the best EMI
performance. Keep the current loop from each of the outputs (VOP and VON) through the ferrite bead, the
small filter capacitor, and back to PGND short and in close proximity.
Grounding It is required to employ a solid metal plane as a central ground connection or star ground for
the ft2820. All ground pins should be individually connected to the star ground pad GND with sufficiently
wide traces.
Thermal Pad The thermal pad must be directly soldered onto a grounded metal pad for proper power
dissipation to ensure optimal performance and long-term reliability. Place sufficient number of solid VIAs
(whose diameter is 0.3mm or less) equally spaced underneath the thermal pad. The VIAs should be
connected to a solid copper plane, either on an internal layer or on the bottom layer of the system board.
Note that the VIAs must be solid ones, not thermal relief or webbed VIAs.
SEP, 2013
http://www.fangtek.com.cn
21
ft2820
TYPICAL APPLICATION CIRCUITS
VDD
Cs
CS1
10uF
1uF
1
EN
2
3
4
CF2
2.2uF
5
6
7
C1 470nF
8
INPUT
9
C2 470nF
10
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
PVDD
ft2820P
CVDD
VOP
PGND
NC
VON
INN
PVDD
INP
NC
AVDD
NC
20
CF1
19
2.2uF
18
17
LS1
16
15
SPEAKER
14
13
COUT
12
11
10uF
100uF
VDD
Cs
CS1
10uF
1uF
1
EN
2
3
4
CF2
2.2uF
5
6
7
C1 470nF
8
INN
9
C2 470nF
INP
10
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
CVDD
NC
PVDD
ft2820P
VOP
PGND
VON
INN
PVDD
INP
NC
AVDD
NC
20
CF1
19
2.2uF
18
17
LS1
16
15
SPEAKER
14
13
12
11
COUT
10uF
100uF
SEP, 2013
http://www.fangtek.com.cn
22
ft2820
TYPICAL APPLICATION CIRCUITS (Contd)
VDD
Cs
CS1
10uF
1uF
1
EN
2
3
4
CF2
2.2uF
5
6
7
R1 1K
L-IN
9
R2 1K
R-IN
C1
470nF
C2
470nF
10
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
PVDD
ft2820P
CVDD
VOP
PGND
NC
VON
INN
PVDD
INP
NC
AVDD
NC
20
CF1
19
2.2uF
18
17
LS1
16
15
SPEAKER
14
13
COUT
12
11
10uF
100uF
R3 0.5K
R3=R1*R2/(R1+R2)
Cs
CS1
10uF
1uF
1
EN
2
3
4
CF2
2.2uF
5
6
7
C1 470nF
R1 10K
8
INPUT
9
C2 470nF
R2 10K
10
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
PVDD
ft2820P
CVDD
NC
VOP
PGND
VON
INN
PVDD
INP
NC
AVDD
NC
20
CF1
19
2.2uF
18
17
LS1
16
15
SPEAKER
14
13
12
11
COUT
10uF
100uF
SEP, 2013
http://www.fangtek.com.cn
23
ft2820
TYPICAL APPLICATION CIRCUITS (Contd)
VDD
VDD
CS3
CS1
CS2
10uF
1uF
10uF
CS4
1uF
1
1
EN
2
3
4
CF2
2.2uF
5
6
7
C1 470nF
8
INPUT
9
C2 470nF
10
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
CVDD
NC
INN
INP
AVDD
PVDD
ft2820P
VOP
PGND
VON
PVDD
NC
NC
EN
20
CF1
2.2uF
19
18
4
17
CF4
2.2uF
LS1
16
6
15
SPEAKER
14
7
C3 470nF
8
13
12
COUT1 + COUT2
9
C4 470nF
10
11
10uF
220uF
CGND
CN1
AGND
PVOUT
EN
CP1
CN2
CP2
CVDD
NC
PVDD
ft2820P
VOP
PGND
VON
INN
PVDD
INP
NC
AVDD
NC
20
CF3
19
2.2uF
18
17
16
15
14
13
COUT3
12
11
10uF
Figure 46: Dual ft2820 in Tandem for Higher Output Power Applications
Note: The bold lines are high current paths and their respective traces are required to be as wide and
short as possible on the system board for high power applications.
SEP, 2013
http://www.fangtek.com.cn
24
ft2820
PHYSICAL DIMENSIONS
E1
E2
D1
#1PIN
HEAT SLUG
SYMBOL
A
A1
A2
A3
b
c
D
D1
E
E1
E2
e
L
SEP, 2013
MIN
0.05
0.90
0.34
0.20
0.10
6.40
4.00
6.20
4.30
2.80
0.45
0
NOM
1.00
0.44
6.50
4.20
6.40
4.40
3.00
0.65BSC
0.60
-
MAX
1.20
0.15
1.05
0.54
0.28
0.19
6.60
4.40
6.60
4.50
3.20
0.75
8
http://www.fangtek.com.cn
A2
A1
A3
UNIT
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
25
ft2820
IMPORTANT NOTICE
1. Disclaimer: The information in document is intended to help you evaluate this product. Fangtek, LTD.
makes no warranty, either expressed or implied, as to the product information herein listed, and reserves
the right to change or discontinue work on this product without notice.
2. Life support policy: Fangteks products are not authorized for use as critical components in life support
devices or systems without the express written approval of the president and general counsel of Fangtek
Inc. As used herein
Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be reasonably expected to result in a significant
injury to the user.
A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.
3. Fangtek assumes no liability for incidental, consequential or special damages or injury that may result
from misapplications or improper use or operation of its products
4. Fangtek makes no warranty or representation that its products are subject to intellectual property
license from Fangtek or any third party, and Fangtek makes no warranty or representation of
non-infringement with respect to its products. Fangtek specifically excludes any liability to the customer or
any third party arising from or related to the products infringement of any third partys intellectual property
rights, including patents, copyright, trademark or trade secret rights of any third party.
5. The information in this document is merely to indicate the characteristics and performance of Fangtek
products. Fangtek assumes no responsibility for any intellectual property claims or other problems that
may result from applications based on the document presented herein. Fangtek makes no warranty with
respect to its products, express or implied, including, but not limited to the warranties of merchantability,
fitness for a particular use and title.
6. Trademarks: The company and product names in this document may be the trademarks or registered
trademarks of their respective manufacturers. Fangtek is trademark of Fangtek, LTD.
SEP, 2013
http://www.fangtek.com.cn
26