Professional Documents
Culture Documents
Elastomeric Bearing Pads and Strips Brochure 2010
Elastomeric Bearing Pads and Strips Brochure 2010
special applications.
The pads nominated in
the following tables have
been designed using the
parameters as specified in
AS5100.4.
Pads are also able to be designed
and offered in accordance with
BS5400 and NAASRA Highway
Bridge Specification(1976).
Vertical Loads
Loadings shown in the table are the
maximum recommended working loads.
At these loads a deflection of up to
15% of the initial pad height could be
expected.
As these pads are not bonded to the
mating surfaces, the actual deflection
Fv
VERTICAL
Shear Deflection/Stiffness
The allowable shear deformation
is normally in the order of 30% to
50% of the compressed pad/strip
thickness from the neutral position.
Shear deflections of up to 70% may be
FV
FH
t
SHEAR
Rotation
Tilting of the load bearing surfaces
relative to each other causes a
rotation of the bearing pad/strip. The
basic limiting criterion is that no gap
occurs between the structure and the
Fv
ROTATION
Slippage
Non-reinforced bearing pads will
spread in surface contact area when
under load. The amount of spread
is largely determined by the frictional
coefficients of the structures surfaces
Slippage
Slippage
Fv
SLIPPAGE
Installation
The mating surfaces should be flat,
parallel and free from cavities, gaps
or protrusions. It is preferable for the
structures surfaces to have a rough
texture without lubrication, particularly
Friction
The bearing is restrained in lateral
movement by the frictional coefficient
between the rubber and the structure.
The ratio of lateral load over vertical
load should not exceed the following
values:
Rubber Specification:
The elastomer supplied will comply with the requirements of AS5100.4 Table B3(A) Type 60H.
Strip
Working Compressive Shear
Shear Rotation
Dimensions
Load per
Stiffness
Stiffness Capacity Capacity
mm x mm Metre kN/m kN/mm/m kN/mm/m +/- mm
rad
5 x 50
5 x 75
5 x 100
5 x 125
5 x 150
5 x 200
200
300
400
500
600
800
550
1163
2001
3061
4348
7599
9.0
13.5
18.0
22.5
27.0
36.0
2
2
2
2
2
2
0.022
0.010
0.006
0.004
0.003
0.002
Type O
Type O
Type O
Type O
Type O
Type O
10 x 50
10 x 75
10 x 100
10 x 125
10 x 150
10 x 200
10 x 50
10 x 75
10 x 100
10 x 125
10 x 150
10 x 200
100
225
400
500
600
800
138
309
550
828
1163
2001
4.5
6.8
9.0
11.3
13.5
18.0
5
5
5
5
5
5
0.044
0.029
0.022
0.014
0.010
0.006
Type O
Type O
Type O
Type O
Type O
15 x 75
15 x 100
15 x 125
15 x 150
15 x 200
15 x 75
15 x 100
15 x 125
15 x 150
15 x 200
150
265
415
600
800
138
244
381
550
933
4.5
6.0
7.5
9.0
12.0
8
8
8
8
8
0.044
0.033
0.026
0.022
0.013
Type O
Type O
Type O
Type O
Type O
Type O
20 x 75
20 x 100
20 x 125
20 x 150
20 x 200
20 x 250
20 x 75
20 x 100
20 x 125
20 x 150
20 x 200
20 x 250
110
200
315
450
800
1000
77
138
215
309
550
828
3.4
4.5
5.6
6.8
9.0
11.3
10
10
10
10
10
10
0.058
0.044
0.035
0.029
0.022
0.014
Type O
Type O
Type O
Type O
25 x 100
25 x 125
25 x 150
25 x 200
25 x 100
25 x 125
25 x 150
25 x 200
160
250
360
640
88
138
198
352
3.6
4.5
5.4
7.2
13
13
13
13
0.055
0.044
0.036
0.027
Type O 25 x 250
25 x 250
1000
550
9.0
13
0.022
Brisbane
Melbourne
Perth
9290 02/09
1.
3.
4.
5.
6.
7.