Professional Documents
Culture Documents
2013 87 - X-EnP Siding and Decking Nail
2013 87 - X-EnP Siding and Decking Nail
General information
Material specifications
Carbon steel shank:
Zinc coating:
HRC 58
816 m
Approvals
ETA-04/0101 (Hilti-DX-DoP001), UL R13203, FM 3021719,
ICC ESR-2197, ESR-2776 (USA), MLIT (Japan), ABS,
LR 97/00077
Applications
Examples
Roof decking
Floor decking
Wall liners
The intended use only comprises fastenings which are not directly exposed to external
weather conditions or moist atmospheres. For out-door applications, that can be ensured
by using SDK 2 sealing caps. During construction exposure to external atmosphere must
not exceed 6 months. Fastening of aluminum sheeting is generally recommended only for
indoor conditions.
12 / 2013
87
X-ENP
Load data
Characteristic loads steel sheeting
Sheeting
thickness
tI [mm]
nominal
Trapezoidal profile
Liner trays 1)
(symmetric loading)
(asymmetric loading)
Char. resistance
Char. resistance
according to ETA-04/0101
keeping to ETA-04/0101
Shear Tension
Shear Tension
NRk [kN]
VRk [kN]
NRk [kN]
VRk [kN]
0.75
0.88
1.00
1.13
1.25
1.50
1.75
2.00
2.50
NRk and VRk are valid for steel sheet with minimum tensile strength 360 N/mm2 ( S280 EN 10346).
For intermediate sheet thicknesses, use recommended load for next smaller thickness or linear interpolation.
1) Required load reduction is taken into account in accordance with EN 1993-1-3: 2006, section 8.3 (7) and
fig. 8.2. See also construction rules under spacings and edge distances.
Trapezoidal profile
Liner trays 1)
(symmetric loading)
(asymmetric loading)
Recommended loads
Recommended loads
Shear Tension
Shear Tension
Nrec [kN]
Vrec [kN]
Nrec [kN]
Vrec [kN]
0.75
0.88
1.00
1.13
1.25
1.50
1.75
2.00
2.50
Nrec and Vrec are valid for steel sheet with minimum tensile strength 360 N/mm2 ( S280 EN 10346).
For intermediate sheet thicknesses, use recommended load for next smaller thickness or linear interpolation.
Recommended loads Nrec and Vrec are appropriate for Eurocode 1 wind loading design with a partial safety
factor F =1.5 for wind load and a partial resistance factor M = 1.25 for the fastening.
1) Required load reduction is taken into account in accordance with EN 1993-1-3: 2006, section 8.3 (7) and
fig. 8.2. See also construction rules under spacings and edge distances.
88
12 / 2013
X-ENP
Tension
Nrec [kN]
0.60
0.75
0.35
0.70
0.90
0.50
0.80
1.00
0.65
0.90
1.20
0.80
1.00
1.30
0.95
1.20
1.55
1.30
1.50
1.85
1.45
2.00
2.55
1.90
1) Only recommended for indoor applications. Constraint forces and corrosion aspects have to be considered.
For intermediate sheet thicknesses, use recommended load for next smaller thickness.
Recommended loads Nrec and Vrec are appropriate for Eurocode 1 wind loading design with a partial safety
factor of F =1.5 for wind load and a partial resistance factor M = 1.25 for the fastening.
Vrec [kN]
Nrec [kN]
4.6
2.4
Fastened parts: clips, brackets, etc.; thick steel parts (tl,max = 2.5 mm).
Redundancy (multiple fastening) must be provided.
The possibility of prying effects has to be considered
Failure of the fastened part is not considered in these values of Nrec, Vrec.
Valid for predominantly static loading
Global factor of safety is 2 based on 5% fractile value
Design
Depending on the verification concept, the corresponding design criteria are given as following.
Working load concept
Tensile loads
NSk Nrec
NSd NRd
Shear loads
VSk Vrec
VSd VRd
N-V Interaction
For combined tensile and shear forces on the fastener, a linear function has to be used.
( VV ) + ( NN ) 1
( VV ) + ( NN ) 1
with:
VSk, NSk unfactored characteristic load acting
on the fastening (= working load)
Vrec, Nrec recommended (allowable) load with
GLOB = 1.875
with:
VSd, NSd Design load with F = 1.5
VRd, NRd Design resistance of the fastening
with M = 1.25
VRd
= VRk / 1.25
= cycl NRk / 1.25
NRd
= 1.0 according to ETA-04/0101
cycl
Sk
Sk
rec
rec
12 / 2013
Sd
Sd
Rd
Rd
89
X-ENP
Application requirements
Thickness of base material
Steel thickness tII
tII
tII 6 mm
(a)
single
(b)
side lap
(c)
end overlap
(d)
side lap and end overlap
0.631.00
a, b, c, d
> 1.001.25
a, c
> 1.252.50
a
With the above recommended sheet thickness and overlap types, it is not necessary to
take into account the effect of constraints due to temperature for steel grades up to S320
(EN 10346). For steel grade S350 (EN 10346) it shall be considered for design. Sheets of
grade S350 on base material tII 8 mm have been verified by Hilti, forces of constraint can
be neglected.
90
12 / 2013
X-ENP
15
10
Trapezoidal profiles
C
45
20
Centre fastenings in
ribs
20
Clearance to end of
sheet
Liner trays
20
80
75
c
90
Clearance to side of
sheet
(1)
Clearance to side of
sheet
Clearance to end of
sheet
Corrosion information
The intended use only comprises fastenings which are not directly exposed to external weather
conditions or moist atmospheres. For outdoor applications that can be ensured by using SDK 2
sealing caps. During construction exposure to external atmosphere must not exceed 6 Month.
Fastening of Aluminum sheeting is generally recommended only for indoor conditions.
12 / 2013
91
X-ENP
Application limit
X-ENP-19 with DX 76, DX 76 PTR and DX 860-ENP
22
21
20
10
18
17
16
15
Applicable
range of base
materials
14
13
12
11
10
9
S 235
S 275
7
6
350
S 355
400
450
500 550 600
650
Steel strength Rm [N/mm2]
700
750
Tools
Fastener guide
Designation
Item no.
Designation
Designation
Single nail:
X-ENP-19 L15
283506
DX 76 PTR
DX 76 F15
X-76-F15-PTR
Collated nails:
283507
DX 76 PTR
DX 76 MX
DX 860-ENP
Piston:
92
X-76-P-ENP-PTR
X-76-P-ENP
283508
DX 76 PTR
DX 76
DX 860-ENP
12 / 2013
X-ENP
DX 76 PTR
>20
18
17
>20
Red 4
or
Black 2
19
Black 4
17
16
15
14
13
12
Red 3
or
Black 1
Black 3
11
10
9
16
15
14
Red 4 or
Black 2
S 235
Red 3
S 355
Black 4
Blue 4
or
Red 2
Red 4
Blue 3
or
Red 1
Red 3
S 235
S 355
S 275
12
11
9
8
Blue 3
Red 4
or
Black 2
13
10
Blue 4 or
Red 2
8
7
18
19
7
6
12 / 2013
93
X-ENP
hNVS
Fastening inspection
tII
tI,tot 4 mm
Max
Min
hNVS = 8.29.8 mm
X-ENP-19 L15
X-ENP-19 L15
Max
Min
Max
Min
Visible inspection:
Properly driven fastener.
Piston mark clearly visible on the
washer.
94
12 / 2013