Professional Documents
Culture Documents
10W Instructions
10W Instructions
usb usb
usb
usb 12V
When using first insert USB, and then plug the power supply.
When not in use, unplug the power supply and pull out the USB,
Don't get the order of the reverse, the computer shutdown is equivalent to pull out the USB.
Because the control chips using usb power supplyMotor and laser using 12V power supply,
If Control chip no power Laser has electricityLaser will lose control,Have a chance to laser damage
5 10
10
can not continuously work too long time, different files and settings fever is different, some 5 minutes to fever
serious, some 10 minutes to start a serious fever, usually work for 10 minutes to touch the gentle temperature
is high should be the pauses to rest. Laser severe fever also continue to work easily broken
2016 6 5 , 40 40 60
June 5, 2016 update with a thermometer, if the display 40 degrees is severe fever should rest (Although the surface
just 40 degrees but core is already 60 degrees)
2016 6 5
Purchased without a thermometer before June 5, 2016
2016 7 () 60
2016-7 Update new heat sink(Without thermometer),Enhanced cooling, generally 60 minutes of continuous work
The disadvantage is that the laser head is too heavy to move speed can not be too fast and Larger fan noise
driver installation
1. C++
2.Instal C++ libra
2. USB
2.installation for the USB Drive
control software
()image engrave.exe
image engrave.exe Is a picture engrave software, open the picture to engrave ,dot matrix printer,Laser head move around ,A line of points
the last full page image or text.
With a successful connection to the machine, we can can work the machine
Start engraving , Pause engraving ,stop engraving
Picture processing
manual control
The rate of move the laser top to bottom and move around
...
Close laser Weak light...intense
The rate of When engraving , speed is too fast will reduce the accuracy (General use Normal )
254DPI 10 =1
,. 339DPI
Direct input text for engraving
font
Hollow character
:
,255 0 , 255
Laser intensity:The maximum power of laser engraving, the 255 is the largest, the 0 is the smallest.General use 255
: 50
Burn time:Unit millisecondThe time per pixel laser irradiation
Different power and different materials need to set different timeUsually no more than 50
255
15 1 1-2
2-4
1-2 1-2 1-2
generally use the following parameters:intensity 255
Stainless steel 15, carton leather 1, cork 1-2 ,hardwood 2-4 ,Bamboo 1-2 ,plastic 1-2
:()
:,,
Z :,.()
:.( Z )
Scanning mode:(general use shortest path)
General: from left to right, then back to the left, from left to right
Z-shaped: from left to right, then right to left. (Accuracy will be a little lower)
The shortest path: according to the order of carving the shortest. (Accuracy is lower than Z-shaped)
:
,, 50
Stable delay:There is vibration, need to be stable after some delay to open laser,General use 50
",,",
Location point:(Two red lines crisscross)
The keyboard Up and down the left and right Can move
Move the mouse to the right click on the picture will pop up "left-top center-top center menu
you can quickly change Location point
gcode cut.exe is a vector cutting software, open the gcode file to be cut, and the picture is different from
the engraving, vector cutting is along the contour line. We usually use this mode to cut through the wood, paper
and other materials.
With a successful connection to the machine, we can can work the machine
: gcode
Start , Pause ,stop
:
Width: displays the width of the current file
manual control
Cutting speed: the speed of movement of laser cutting, expressed in (mm \'s). This speed is also used to control the depth of the cutting,
for the specific laser intensity, the slower the speed, the greater the depth of the cut, Speed is too fast will reduce the accuracy
Laser intensity: the intensity of the laser beam to the surface of the material. For specific cutting speed,
the greater the intensity, the deeper the cutting.
()
Travel speed: positioning of the moving speed, speed is too fast will reduce the accuracy(General use Normal )
Repeated number of times: the material can be cut through the repeated number of times repeated cutting
",,"
Location point:(Two red lines crisscross)
The keyboard Up and down the left and right Can move
Move the mouse to the right click on the picture will pop up
"left-top center-top center menu
you can quickly change Location point
Focusing
()
()
In reflective, transparent, high temperature resistance,
with laser color similar to the color (blue) material
is difficult to engraving.But if it is painted black on the surface,
it is easy to engraving.Use the water-based marker pen to blacken,
finish engraving then erase Paper towel wipe clean
Inkscape(gcode)
download http://acanlaser.b0.upaiyun.com/inkscape.zip
install
inkscapegcode inkscape/share/extensions
Installation completed, Copy gcode all files to the installation directory under
inkscape/share/extensions directory
the
Can also Convert bitmap into vector
common problem :
1 No trace of engraving
5 10
10
The laser head is burnt out
Under the environment of high temperature laser is easy to be bad, couldn't work for too long time, different
files and settings fever is different, some 5 minutes to fever serious, some 10 minutes to start a serious fever,
usually 10 minutes the touch temperature is high temperature should be the pauses to rest. Laser fever serious
still continue to work easily bad
2
USB
USB -
prolific USB-to-Serial Comm Port(comXX)
2: the software can not connect the engraving machine.
The USB driver not installed
Plug in USB, "my computer" - "properties", "device manager"
See the "port" USB-to-Serial Comm Port prolific (comXX) on behalf of the normal drive installation
3
-
XP net3.5 win7
net3.5 : http://www.microsoft.com/zh-cn/download/details.aspx?id=22
Parameters for test steel sheets