Professional Documents
Culture Documents
COD Test Report Latest 2012
COD Test Report Latest 2012
BFC 32501
1.0 OBJECTIVES
To determine the organic oxidize able matters content of water samples.
3.0 THEORY
The chemical oxygen demand (COD) is the amount of oxygen consumed to completely
chemically oxidize the organic water constituents to inorganic end products. COD is an
important, rapidly measured variable for the approximate determination of the organic matter
content of water samples. Some water samples may contain substances that are difficult to
oxidize. In these cases, because of incomplete oxidation under the given test methods, COD
values may be a poor measure of the theoretical oxygen demand. It should also be noted that
the significance of the COD value depends on the composition of the water studied.
COD is used as a measurement of pollutants in natural and waste waters to assess the
strength of discharged waste such as sewage and industrial effluent waters. It is normally
measured in both municipal and industrial wastewater treatment plants and gives an
indication of the efficiency of the treatment process. The dichromate reflux method is
preferred over procedures using other oxidants because of superior oxidizing ability,
applicability to a wide variety of samples, and ease of manipulation. Oxidation of most
organic compounds is 95-100% the theoretical value.
4.0 EQUIPMENT
BFC 32501
COD Reflux System consisting Erlenmeyer flask (250 mL or 500 mL) with groundglass 24/40 neck and 300-mm jacket Liebig West, or equivalent condenser with 24/40
ground-glass joint, and a hot plate having sufficient power to produce at least 1.4
W/cm2 of heating surface.
1.0 Burette
2.0 Pipette
3.0 Glass beads
4.0 Magnetic stirrer bars
5.0 PROCEDURE:
1.
Boil flask reflux (vaporization and perspiration) long 1 hours. Boiling could prevent
organic substances boiling over of lost. While waiting 1 hours, another experiment
on how to find the normality was being carried out
BFC 32501
4 Distilled water blend until volume achieve 140 mL. 2 to 3 solution drop indicator
ferrion (1-10 fenantrolin). magnet stem included and is stirred use magnetic stirrer
5. Ammonia ferric sulphate (0.25M) has been standardized titrated to fixed color to the
first emerges. Alert because point color final can be change quickly. First and final
reading burette is being recorded.
BFC 32501
FIRST READING
9 ml
10
x 0.25
19 9
Waste water
Tap water
LAST READING
19 ml
BFC 32501
DATA:
DATA :
First Reading
Last Reading
Volume Reading
15.8
23
0.18
CALCULATION :
10
x0.25
23 15.8
= 0.18
COD CALCULATION :
First Reading
Last Reading
Volume Reading
CALCULATION :
10
x 0.25
15.8 5
= 0.27
5
15.8
0.27
BFC 32501
8.0 DISCUSSION
1.
The main reason for using the blank sample is to control the volume of
organic material in the sample. COD was carried out to measure the oxygen
demand of organic compounds in a sample of water, and we have to ensure there
were no accidentally outside organic materials added to the sample to be
measured. A blank sample is created by adding the reagents to a volume of
distilled water. Both water and blank sample will be compared. The oxygen
demand for the blank sample is subtracted from the COD for the original sample
to ensure the true measurement of organic matter.
2.
BFC 32501
What is the objective of COD test and what is the different between COD and
BOD test?
-
3.
BFC 32501
Why the CODs value needs to be monitor for the polluted surface water such
as in lakes and rivers as well as for waste water?
-
9.0 CONCLUSION
The result we have during the test lab of COD after the analysis and calculation actually
are succeed and is not more different from the accurate reading when to do until third test, at
first test lab we got the 0.297 for NAS, we have the result is bad and not accurate, the result
must in range 0.23 0.28 in NAS, and from NAS, the calculation of COD can make to get
the result for the sample.
The was on experimental of my group, result had we got are not accurate because the
range has the provide is place at out, after the experiment try again, we obtain the result are
present at in the range, so from mistake data we obtain, we can say the experiment has we do
the time when the sample in distilled water plus with reagent, then agen chemical sulphuric
together, let the sample are cooled in warm, after that 2 to 3 indicator drop ferroin and titrated
with ferrous ammonium sulphate and stir in slow, titration discontinued after colour changed
from blue greenness to red-brown, that should be, but my group has identified and post
mortem, the answer we are slow and to late acting for discontinued of the titration, so that the
reading of the ammonium sulphate are had we take are less even one driblets. The one
driblets are able to change the data for calculation of COD.
The lastly after got the result of NAS are in range, so we proceed to get the COD with
another calculation, the result of NAS are to will use for calculation of COD, from
calculation, were obtain 0.85 mg/l for COD. The sample are were use for 0.85 mg/l is amount
BFC 32501
of oxygen (COD) consumed to completely chemically oxidize the organic water constituents
to inorganic end products. Now the student know why the conclusion or result is must need in
the each the experimental.
8.0 REFERENCES
1. http://www.hbcse.tifr.res.in/protocol_guide.pdf
2. www.norweco.com/html/lab/test_methods/5220bfp.htm
3. www.pavloschemicals.com/lab
4. www.labseeker.com/labsupplies/lablist