Professional Documents
Culture Documents
Design Engineering Services Brochure
Design Engineering Services Brochure
Design Engineering Services Brochure
COMPANYPROFILE
www.edes.com.my
ContentList
Content
Page
Company Background
Corporate Information
Mission Statement
Principal Activities
10-29
30-34
EPCC Contractor
35-37
Technology Partners
38
CompanyBackground
EDES Technology
is a market - leading technology and engineering company, focusing on
multi-disciplinary onshore and offshore facility designs mainly for the oil and gas,
petrochemical and power plants industries. We emphasize on ease of operation
and constructability mainly in basic engineering designs related to the production
systems for various process facilities. This critical integration is positive because we have
innovative solutions and experiences that transcend every project phase including
initial conception, FEED, detailed engineering, fabrication, installation,
commissioning and operation, from complex projects to the optimization
of classic designs. We provide design and engineering solutions that meet our clients
objectives to achieve optimum performance of their facilities in both technocommercial
aspects.
Corporate
Information
Corporate Address :
C3-2-10, Level 2, Block C3,
Solaris Dutamas, No.1,
Jalan Dutamas 1,
50480 Kuala Lumpur,
MALAYSIA
Fabrication Yard :
Lot 74-A, Jalan Gebeng 1/6,
Gebeng Industrial Estate,
26080 Kuantan, Pahang,
MALAYSIA
ROC No. :
891026-K
Company Secretary:
Symphony Corporatehouse
Contact No. :
Fax No. :
E-mail :
Website :
+603-6207 9988
+603-6207 9889
edes@edes.com.my
www.edes.com.my
MISSION STATEMENT
Mission Statement
We specialize in consultancy, engineering design and product developement for process
facilities in the global upstream & downstream oil & gas industries, petrochemical refineries
and power plants.
We are able to provide optimum solutions by maximizing engineering expertise and
technical knowhow, safety, quality and technological innovations in order to achieve
satisfaction for our clients and shareholders.
PRINCIPAL ACTIVITIES
1. Sand Separation And Management Systems
2. Seawater Injection And Treatment Systems.
3. Produce Water Treatment Systems.
4. MBBR for Wastewater Treatment.
PRODUCTS
AND
TECHNOLOGY
POLICY
POLICY
Quality Policy
EDES Quality Policy focuses on the following actions;
1. To provide designs and product development in compliance with International Standard
and best engineering practices.
2. To deliver our services and products on time.
3. To ensure our services and products are fully acceptable for our clients.
4. To ensure efficiency and effectiveness of our human capital in carrying out their responsibilities.
5. To provide our services and products at the most competitive cost.
2. PE1130100
14. SM2031100
Design Capabilities ;
1. Process Design (Aspen HYSIS)
2. Mechanical Design (PV Elite)
3. Thermal Design (HTRI)
4. Piping Design (Caeser 11.5.3)
5. Structural Design (Staad Pro / Solid Work)
6. Finite Element Analysis (ANSYS / Solid Work)
7. Computational Fluid Dynamics. (Sold Work)
8. 3D Modelling And Drafting (AUTOCAD Inventor / CADWORX)
ORGANISATION &
FUNCTIONAL STRUCTURE
BUSINESS DEVELOPMENT
MANAGING DIRECTOR
EXECUTIVE DIRECTORS
TENDER / PROPOSAL
QA/QC
PROCUREMENT
BUSINESS DEVELOPEMENT 1
PROPOSAL ENGINEER 1
QA/QC ENGINEER 1
PROCUREMENT EXEC 1
BUSINESS DEVELOPEMENT 2
PROPOSAL ENGINEER 2
QA/QC ENGINEER 2
PROCUREMENT EXEC 2
TECHNOLOGY DEVELOPMENT
& DESIGN
PROJECT MANAGEMENT
FINANCE
ADMIN / IT
PROCESS ENGINEER 1
PROJECT MANAGER 1
ACCOUNT EXEC 1
ADMIN EXEC 1
PROCESS ENGINEER 2
PROJECT MANAGER 2
ACCOUNT EXEC 2
ADMIN EXEC 2
MECHANICAL ENGINEER 1
PROJECT ENGINEER 1
MECHANICAL ENGINEER 2
PROJECT ENGINEER 2
STRUCTURAL ENGINEER 1
PROJECT ENGINEER 3
STRUCTURAL ENGINEER 2
PROJECT ENGINEER 4
E & I ENGINEER 1
E & I ENGINEER 2
DESIGNER 1
DESIGNER 2
10
11
12
to
ensure
maximum
flexibility,
13
14
15
CORRUGATED PLATE
INTERCEPTOR (CPI)
DEOILING HYDROCYCLONES
Our deoiling hydrocyclone liners are of the latest generation in high efficiency cyclone design.
Therefore, this provides our customers with the
following benefits:
Exceptional removal efficiency up to 99%
Bulk oil removal up to 20% free oil.
Discharge levels can be below 10ppm.
Low pressure operation.
High erosion resistance.
Compact.
No moving parts.
High - capacity designs.
Insensitive to motion.
DEOILING HYDROCYCLONES
16
17
18
19
We can also offer a high-rate, multi-media downflow filter designed specifically for the unique challenges of Produced Water Treatment for injection.
20
21
Desalting Adding water which is less saline than the water contained in the feedstock
crude converts a dehydrator into a desalter. Typical single-stage removals are illustrated in
Figure 2.
--
22
23
DC Electrostatic Coalescer:
Only for essentially non-conductive, clean, distillate and light hydrocarbon service.
Typical power rating 10 kVA, (5 kVA and 15 kVA are also available).
Typical liquid carryover is about 5 10 ppm.
Used to desalt distillate fuels used in gas turbines.
24
25
26
27
28
PROCESS CONFIGURATION
29
LCT1 - BIOMATRIX
LCT1 - BIOMATRIX
A low-carbon technology biofilter media
(LCT1-Biomatrix) of composite material properties
and design features to;
(1) Concentrate soluble organics especially those
with low-molecular weight compounds into its
body.
(2) Remove slowly biodegradable organics and
also treat high-strength organics.
(3) Its effluent can meet stringent water quality
standard for discharge and reuse. It removes
higher percentage of soluble organics than biotreatment alone.
30
31
Compressor Skid
Sand Management
Metering Skid
Pump Skid
Separator System
Fuel Gas Treatment
32
from COADE for the code calculation and reputable engineering formula for common mechanical solutions.
EDES Technology provides 3D modeling for skid piping. The complete piping flexibility and stress analysis is provided to study the varieties of load on the piping system subjected to pressure, thermal, seismic and other environtmental conditions.
ASME 31.3
PD 5500
ASME 31.4
ASME 31.8
TEMA
ROARKS FORMULA
WRC 107, & 297, ANNEX G
33
d) THERMAL DESIGN
Especially for Shell & Tube Heat Exchanger and Double Pipe Heat Exchanger. HTRI
is the leader in process heat transfer technology and our involvement provides
excellent designs and analysis that meet the process requirements of our clients.
34
35
EPCC CONTRACTOR
OUR DETAILS
OUR FABRICATION, PLANT MAINTENANCE &
PROJECT MANAGEMENT SERVICES
Manufacturing of process equipment:
pressure vessels, heat exchangers and storage tanks.
Fabrication of process skids.
Manufacturing of equipment lifting frames and ISO tanks for offshore containers.
Engineering, Procurement, Construction and Commissioning work.
Plant maintenance and turnaround.
36
EPCC CONTRACTOR
OUR DETAILS
PROCUREMENT
Our Procurement Function covers overall cycle of the activities in projects in line
with our internal system; Approved vendor list
Pre-qualification of vendor products and services
Product Service Enquiry
Technical and commercial evaluation
Award and issuance of Purchase Order
Expediting and Inspection
Logistic coordination
Invoicing and P.O close out
8. Invoicing
and P.O
close out
PROCUREMENT
3. Product
Service
Enquiry
4. Technical
and commercial
evaluation
37
EPCC CONTRACTOR
OUR DETAILS
CONSTRUCTION
Our construction teams are specialized in every aspect of facilities development
from basic to the complete process facilities; Preparation of civil works - land survey and soil report
Construction of facilities foundation
Fabrication of process equipment, piping and structural components
Lifting, installation and alignment of the mechanical equipment and piping erection
Installation of electrical and instrumentation components
Field inspection and testing of the system
Start-up and pre-commissioning
Final inspection and acceptance
SYSTEM INTEGRATION
Integration of the process control components and process equipment
such as DCS, ESD and MCC.
Our commissioning teams are experienced to complete the projects by; Implementing pre-commissioning and commissioning plans
with project manpower and documentation.
Preparation of commissioning procedure, commissioning check-list,
certification, punch-list and hand-over procedure.
38
Our Technology
Partners
Address :
C3-2-10, Level 2, Block C3, Solaris Dutamas,
No 1, Jalan Dutamas 1,
50480 Kuala Lumpur, Malaysia.
Tel : 03 6207 9988
Email : edes@edes.com.my