Professional Documents
Culture Documents
Manual For Magnetic Lock
Manual For Magnetic Lock
INSTALLATION INSTRUCTIONS
Model:
D311-180A/B
D312-180A/B
D311-280A/B
D311-280A/B
D313-180A/B
D312-280A/B
D313-560B
D313-280A/B
Power supply
Operation current
500mA/12VDC
Door sensor
200mA/24VDC
NO
0Sec./3Sec./5Sec./9 Sec.
Out-swing door and In-swing door
Holding forces
180Kg/280Kg/560Kg)
Operation temperature
Warranty
250mA/24VDC
Weight
Type
Body
Quantity
A rm a tu re(M i n i)
6.4m m
(1 /4 " x
x 12 .5 m m
1/2 ")
8 .0 m m
6.4 m m
( 5/16 ")
(1 /4" x
x 1 2.5m m
Alignment
sticker
1/2 ")
Magnet(Mini)
3.2mm(1/8")
8mm(5/16")
Sexnut Bolt
Door spacer
Screw 4X25mm
Screw 4X15mm
Screw 5X32mm
Screw 5X25mm
Rubber washer
Washer
Allen keys 3mm
Hexgon keys 5mm
Guide pins
1
1
6
3
4
2
2
3
1
1
2
3.2mm(1/8" )
Page
Installation instructions :
When installing magnetic lock user should be sure of the type of door used .Magnetic
lock is specifically for the use of out-swing door.A bracket is used to install with
magnetic door for in-swing door.
Armature
Bracket
Door
Frame
Armature
Screw
Outdoor
Z Bracket
Door leaf
L Bracket
Indoor
[Out-swing door]
[In-swing door]
[Installation ]
[L.Z. Bracket]
[Out-swing door]
Step1 :
Place the magnet template on top of door frame and the armature template on top of door
leaf according to the above drawings . Try to check if they are on the right position before
drilling all the holes.
Mounting
Step2 :
Fix the mounting plate in the door jamb using
supplied self-tapping screw.
plate
Step3 :
Ensure the armature is set to the right position and drill a 12 mm hole from sexnut
bolt side and drill an 8 mm hole through the door .When hollow door is used , user
should drill a 16 mm hole . A door spacer is used to fit in a sexnut bolt. Then,push
the sexnut bolt in the drilled hole and tighten it with screw driver . The armature
must be loose slightly to compensate the door misalignment , so that the armature
face and the magnet face can be closed and make the magnetic force to maximum
effect.
Rubber washer
Rubber
washer
Sexnut Bolt
Armature Screw M8
Door
Drill 12 mm (12) X
25mm (1) from sexnut
Drill an 8mm (516)
hole through door
[1]
leaf
Knock guide
pins in to
fasten the
armature
[2]
must be
slightly
loose
Page
+V
Power Input
Body
Power I nput
COM
N. O.
N. C.
Armature
+V
V
N. O.
COM
N. C.
Primary
Standard
Blade Stop
Door
Power
2.5sec
V+
0.0 SEC
2.5 SEC
5.0 SEC
9.0 SEC
Supply
V9.0sec
Mounting Plate
ON
5.0sec
P.S
S2
Exit
Bu tton
Voltag e Selec t
12V
24V
N.O
COM .
N.C
1
2
ON
lock
Monitor Output
Autolock Delay
Time Settings
Monitor output (0.5A) will change to N.O. point when
magnetic lock and armature are engaged (Red light of indicator
will change to green light )
Armature
Rubber Washer
Door leaf
[Installation diagram]
Step 5 :
Fix the magnet to the mounting (screws for fitting are included in the magnetic body)
and ensure the armature close lightly against the magnet when the door is closed to
avoid damage to the mating surface unnecessary.
[In-swing door] (Bracket shall be used to install)
Step 1 :
Fix the magnet in the door jamb and fix the armature with the L.Z. bracket in the
door leaf. (as follow)
Outdoor
Indoor
Armature
Bracket
Outdoor
Door
Frame
Armature
Screw
Pull
Z Bracket
Outdoor
Indoor
Door leaf
L Bracket
Indoor
Attentions:
(1) Regardless the type of door used, the lock must be installed or mounted indoors.
(2) The armature must be
misalignment.
(3) Door spacer is used to prevent any damage to the hollow door when it is tightened.
(4) One series of armature brackets are used when installing out-swing.
glass
door
wooden
door
wooden
door
To be used with
bracket
Glass holder
Page