Professional Documents
Culture Documents
Datasheet - HK md7133h 7759585
Datasheet - HK md7133h 7759585
MD71XXH Series
30mA
The MD71XXH series is a family of Low Dropout Positive regulators.which developed by using
CMOS technology. These IC products perform with high output voltage accuracy, low quiescent
current , Low Input-Output Dropout as built-in low on-resistance.At the same time with high input
voltage capacity it can be up to 30V, suitable for applications which requires higher voltage
circuit.
Ferture(Typical)
high output voltage accuracy
3
low dropout voltage
40mV
low quiescent current
1.2uA
low output voltage temperature drift
50 PPm /
high input voltage
up to 30V keeping stable output voltage
Output short circuit protection
Short-circuit current less than 100 mA
Applications
battery-powered devices
communications equipments
portable medical equipments
Selection table
Part NO.
Output voltage
(Note)
3.0V
3.3V
3.6V
4.4V
5.0V
Tolerance
3%
3%
MD7136
3%
MD7144
3%
MD7150
3%
NOTE: for semi_custom parts selectable output voltage from 1.5~7.0V in 0.1v
Increment.
MD7130
MD7133
VIN
VOUT
PD
Operation temperature
Topr
range
Storage temperature
Tstg
-40~+125
range
Note: The absolute maximum ratings are rated values exceeding which the product could
suffer physical damage. These values must therefore not be exceeded under any conditions.
Electrical Characteristics
MD71XXH seriesMD7130HOutput voltage +3.0VTa=25 unless otherwise specified
ITEM
SYMBOL
CONDITIONS
MIN
TYPE
MAX
UNITS
Output voltage
Output current
VOUT
IOUT
VIN= 5VIOUT=10mA
VIN= 5V
2.91
25
3.0
3.09
30
V
mA
Vdrop
IOUT=1 mA
40
60
mV
VOUT1
VINVOUT
VOUT2
4VVIN30V
IOUT=1mA
VIN=5V
1.0mAIOUT30mA
VIN=5VIOUT=10mA
-40Ta85
VIN=5V
--
0.05
0.2
/V
60
100
mV
50
100
1.2
3.0
Ppm/
uA
30
Test
circuits
1
3
*1
Dropout voltage
*2
Line regulation
Load regulation
Temperature
coefficient
Current
consumption
Input voltage
VOUT
TaVOUT
ISS1
VIN
SYMBOL
CONDITIONS
MIN
TYPE
MAX
UNITS
Output voltage
Output current
VOUT
IOUT
VIN= 5.3VIOUT=10mA
VIN= 5.3V
3.201
25
3.3
3.399
30
V
mA
Vdrop
IOUT=1 mA
IOUT=10 mA
4.3VVIN24V
IOUT=1mA
VIN=5.3V
1.0mAIOUT100mA
VIN=5.3VIOUT=10mA
-40Ta85
VIN=24V
--
40
60
mV
0.05
0.2
/V
60
100
mV
50
100
1.2
3.0
ppm/
uA
30
Test
circuits
1
3
*1
Dropout voltage
*2
Line regulation
Load regulation
Temperature
coefficient
Current
consumption
Input voltage
VOUT1
VINVOUT
VOUT2
VOUT
TaVOUT
ISS1
VIN
SYMBOL
CONDITIONS
MIN
TYPE
MAX
UNITS
Output voltage
Output current
VOUT
IOUT
VIN= 5.6VIOUT=10mA
VIN= 5.6V
3.492
25
3.6
3.708
30
V
mA
Vdrop
IOUT=1 mA
IOUT=10mA
4.6VVIN24V
IOUT=1mA
VIN=5.6V
1.0mAIOUT100mA
VIN=5.6VIOUT=10mA
-40Ta85
VIN=24V
--
60
mV
Test
circuits
1
3
*1
Dropout voltage
*2
Line regulation
Load regulation
Temperature
coefficient
Current
consumption
Input voltage
VOUT1
VINVOUT
VOUT2
VOUT
TaVOUT
ISS1
VIN
40
0.05
0.2
/V
60
100
mV
50
100
1.2
3.0
ppm/
uA
30
SYMBOL
CONDITIONS
MIN
TYPE
MAX
UNITS
Output voltage
Output current
VOUT
IOUT
VIN= 6.4VIOUT=10mA
VIN= 6.4V
4.268
25
4.4
4.532
30
V
mA
Vdrop
IOUT=1 mA
40
60
mV
VOUT1
VINVOUT
VOUT2
5.4VVIN30V
IOUT=1mA
VIN=6.4V
1.0mAIOUT30mA
VIN=6.4VIOUT=10mA
-40Ta85
VIN=6.4V
--
0.05
0.2
/V
60
100
mV
50
100
1.2
3.0
ppm/
uA
30
Test
circuits
1
3
*1
Dropout voltage
*2
Line regulation
Load regulation
Temperature
coefficient
Current
consumption
Input voltage
VOUT
TaVOUT
ISS1
VIN
SYMBOL
CONDITIONS
MIN
TYPE
MAX
UNITS
Output voltage
Output current
VOUT
IOUT
VIN= 7VIOUT=10mA
VIN= 7V
4.85
25
5.0
5.15
30
V
mA
Vdrop
IOUT=1 mA
40
60
mV
VOUT1
VINVOUT
VOUT2
6VVIN30V
IOUT=1mA
VIN=7V
1.0mAIOUT30mA
VIN=7VIOUT=10mA
-40Ta85
VIN=7V
--
0.05
0.2
/V
60
100
mV
50
100
1.2
3.0
ppm/
uA
30
Test
circuits
1
3
*1
Dropout voltage
*2
Line regulation
Load regulation
Temperature
coefficient
Current
consumption
Input voltage
VOUT
TaVOUT
ISS1
* Increasing
VIN
output current slowly, The IOUT when output voltage decreasing two
percent
* Vdrop=VIN1-VOUTE0.98V
VOUT(E)Effective output voltage, i.e., the output voltage when fixing IOUT(=1mA) and inputting
VOUT(S)+2.0 V.
VIN1is the Input voltage at which output voltage becomes
Test Circuits
1.
2.
3.
Standard Circuit:
Note: The above connection diagram and constant will not guarantee successful
operation.Perform through evaluation using the actual application to set the constant.
using
conditions:
Technical Terms
1. Output capacitors (CL)
Output capacitors are generally used to stabilize regulation operation and to improve
transient response characteristics. But the MD71XXH series can provide stable operation
without output capacitors. Capacitors are used only to improve transient response
characteristics. Output capacitors can hence be removed in applications in which
transient response can be negligible. When an output capacitor is used, a low ESR
(Equivalent Series Resistance) capacitor like ceramic capacitor can also be used.
(VOUT1/VIN*VOUT)
These parameters indicate the input voltage dependence on the output voltage. That is,
the values show how much the output voltage changes due to a change in the input voltage
with the output current remained unchanged.
4. Load regulation (VOUT2)
This parameter indicates the output current dependence on the output voltage. That is,
the value shows how much the output voltage changes due to a change in the output current
with the input voltage remained unchanged.
5. Dropout voltage (Vdrop)
This parameter indicates the difference between the input voltage (VIN1) and the output
voltage when output voltage falls to 98 % of VOUT(E) by gradually decreasing the input
voltage (VIN).
Vdrop = VIN1-[VOUT(E) 0.98]
Description of Operation
1.Basic Operation
Figure 8 shows the block diagram of the MD71XXH series.The error amplifier compares
a reference voltage Vref with a part of the output voltage divided by the feedback
resistors Rs and Rf, and supplies the gate voltage to the output transistor, necessary
to ensure certain output voltage independent from change of input voltage and
temperature.
VIN
*1
Current sauce
Error amplifier
VOUT
Vref
Rf
Vfb
Rs
VSS
Figure 8
*1. Parasitic diode
2.Output Transistor
The MD71XXH Series uses a Pch MOS FET as the output transistor.
The voltage at VOUT must not exceed VIN+0.3V. When the VOUT voltage becomes higher than
that of VIN, reverse current flows and may break the regulator since a parasitic diode
between VOUT and VIN exists inevitably
3. Short-circuit protection
Installation of the short-circuit protection which protects the output transistor
against short-circuit between VOUT and VSS can be selected in the MD71XXH series. The
short-circuit protection controls output current as shown in the typical characteristics,
(1) OUTPUT VOLTAGE versus OUTPUT CURRENT, and suppresses output current at about 40 mA
even if VOUT and VSS pins are short-circuited.
The short-circuit protection can not at the same time be a thermal protection. Attention
should be paid to the Input voltage and the load current under the actual condition so
as not to exceed the power dissipation of the package including the case for
short-circuit.When the output current is large and the difference between input and
output voltage is large even if not shorted, the short-circuit protection may work and
the output current is suppressed to the specified value. Products without short-circuit
protection can provide comparatively large current by removing a short-circuit
protection.
Precautions:
Design wiring patterns for VIN, VOUT and GND pins to hold low impedance.
When mounting an output capacitor between the VOUT and VSS pins (CL) and a
capacitor for stabilizing the input between VIN and VSS pins (CIN), the distance from the
capacitor to the VOUT pin and to the VSS pin should be as short as possible.
Note that output voltage may be increased at low load current of less than 1 uA.
To prevent oscillation, it is recommended to use the external parts under the following
conditions.
Equivalent Series Resistance (ESR): 30or less
Input series resistance (RIN): 10or less
A voltage regulator may oscillate when power source impedance is high and input
capacitor is low or not connected.
The application condition for input voltage and load current should not exceed the
package power dissipation.
Pay attention to the operating conditions for input/output voltage and load current so
that the power loss in the IC does not exceed the power dissipation of the package.
Do not apply an electrostatic discharge to this IC that exceeds the performance
ratings of the built-in electrostatic protection circuit.
SII claims no responsibility for any and all disputes arising out of or in connection
with any infringement of the products including this IC upon patents owned by a third
party.
Application Circuits
Basic Circuits
V OUT=V XX (1+R2/R1)+Iss*R2
VOUT=VXX+VD1
Dual Supply
IOUT=Vxx/RA+Iss
V10.8.20 xF
10