Professional Documents
Culture Documents
Log Scale Manuplation 111
Log Scale Manuplation 111
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
1/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
The "generic" labeling is done differently on different brands of paper. Some label the start of a cycle with
"1"; some use "10". Some mark 1.5 and 2.5; some don't.
The user has less freedom in labeling a log scale than a linear one. The scales are directed, i.e., one-way,
and cannot be labeled in the opposite direction.
The underlying principle of the log scale is that lengths along the scale are proportional to the logarithms of
the plotted values. The C and D scales of slide rules are constructed the same way.
The user must carefully examine the markings of the scale to correctly interpret its subdivisions. Some
intervals have 10 subdivisions, some only five (every second one of the ten being shown). Errors in the
use of log paper result from failure to notice these differences in the way subdivisions are labeled.
Graph papers with one linear and one logarithmic scale are called semi-logarithmic, log-linear, or simply
logarithmic. Graph papers with both scales logarithmic are called log-log, full log, or dual logarithmic.
As is evident from the 10 divisions of each cycle, these logarithmic scales represent base-10 logarithms.
EXPONENTIAL RELATIONS of the form
y = Aeax
[7-12]
where A and a are constant, can be rendered as straight lines on semi-log paper. To see this, take the
logarithm of both sides of
y/A = eax
[7-13]
which gives
log y - log A = x a log e = x a (0.43420...)
[7-14]
Plot x on the linear axis and y on the logarithmic axis. The resulting straight line will have slope
log y2 - log y1
= a log e
x2 - x1
[7-15]
2/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
since the logarithms are proportional to lengths. Measure the length of one cycle on the paper. Measure
the length between y2 and y1. Then
L/C = log2 y - log1 y
[7-16]
where L is the length along the log axis between the two points, and C is the length of one cycle measured
along that axis.
This is true because for one cycle,
log (10y) - log (y) = log (10) = 1.
[7-17]
This method makes it unnecessary to look up or evaluate the logarithms of the data points.
Example: This graph happens to have cycles 4.15 cm long.
[Because of unavoidable size changes in the reproduction process,
the measurements we have made on the original will be different
from those on your copy. Measurements made from your copy will,
however give the same final values of A and a.]
The variable x is plotted on the horizontal axis and y is plotted on the
vertical axis.
When x = 0, then y = Ae0 = A. So the y-intercept is the value of A.
But x = 0 lies off the edge of the graph, so this would not be a good
way to find the value of A in this case. Let us postpone this problem
and first find the slope.
Fig. 7.9. Semi-logarithmic
Choose two points on the line. I chose the points with values x=2
graph paper.
and x=7 on the horizontal axis. Mark these points on your copy of
Fig. 7.8. They have values of y=20 and y=500 on the vertical axis. A ruler shows that 20 and 500 are
separated by 5.85 cm vertically.
The slope of the line is therefore
5.85 cm
4.15 cm
[7-18]
1.41
= = 0.2819 = a log e
7-2
5
[7-19]
a = = 0.6491
0.4343
The numerator on the left of Eq. 7-18 is dimensionless, so the units of a will be the reciprocal of the units
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
3/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
of x.
Now we can evaluate the constant A. Take any value of x that is on the graph, say x = 7. From the
graph, this gives y = 500. Then
y
500
500
A = = = = 5.317
ax
e
7a
e
[7-20]
94.04
[7-21]
Notice that in this whole process we never had to take a logarithm of any data values.
EXERCISE (7.8) Check Eq. 7-21 by evaluating y for x = 3.4 and comparing the result with the graph.
{Answer 48.32; the agreement is good.}
EXERCISE (7.9) Use Eq. 7-21 to calculate y for x = 6.2. Compare with the graph.
POWER RELATIONS of the form
y = Kxp
[7-22]
may be rendered straight by plotting on log-log paper. Take the logarithm of both sides
log y = log K + p log x
[7-23]
[7-24]
where, as before, the points 1 and 2 are well-separated points on the straight line. Neither intercept has
any special, useful, meaning on this graph! (On log paper log x never has a zero value.)
We have several ways to calculate the slope, once we have specified two well- separated points on the
line, and obtained equation (7-24).
(1) Evaluate equation (7-24) by explicit calculation of the logarithms.
(2) Set up the right triangle and measure the lengths of the legs. Then, as before:
length of the "y" leg
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
[7-25]
4/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
On most log-log graph paper, the lengths of the cycles on the x and y axes are simply related. If they are
equal, then the slope is simply
length of one "y" leg
[7-26]
= tan q = p
length of the "x" leg
So in this special case one may simply measure the angle, q, to determine the slope.
Example: Data that plots as a straight line on
log-log paper can always be expressed by the
relation
y = Kxp
[7-27]
-4.42 cm
[7-28]
= = -0.5423 = p
Dx
8.15 cm
As a check, the slope angle, measured with a protractor, is -28, approximately. The tangent of this is
-0.5317. Considering measurement errors on this small graph, this is good agreement. In your
experimental work, always use the largest possible area of the graph paper.
Therefore:
y = Kx-0.5423
[7-29]
Now we can determine K be taking any point on the line and solving this equation. Let's take the point x
= 2. At this point y = 300.
x-0.5423 = 0.6867
y
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
[7-30]
5/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
K = = 300/0.6867 = 436.9
x-0.5423
[7-31]
This expression shows more digits than is justified by the precision of measurements from this size of
graph. An examination of the actual data uncertainties would help determine the appropriate amount of
rounding for K and p.
EXERCISE 7.10: Check Eq. 7-31 by calculating y at x=80 and compare with the graph. {Answer:
40.58}
EXERCISE 7.11: Check Eq. 7-31 by calculating y at x=29 and compare with the graph.
EXERCISE 7.12: Use Eq. 7-31 to calculate x for y=70. Compare with the graph.
OTHER RELATIONS. The above discussion covers only the most commonly encountered cases.
Other special graph papers are available, which can straighten out graphs of many kinds of relations. To
list a few; polar coordinate, bipolar coordinate, elliptical, hyperbolic, Smith charts (a grid of orthogonal
circles). It has been suggested as a joke that someone ought to print graph paper on rubber sheets, so
you could straighten out any curve by warping the grid lines! But that is what these various papers do for
you. They are only useful if the warping of the grid lines corresponds to an accurately known
mathematical relation that can be mathematically transformed back to a linear grid.
RESCALING LOGARITHMIC SCALES. We have so far only
considered rescaling log scales by multiplying each scale value by some
factor of 10. This preserves the cycle length. Other labelings are possible,
but one must exercise great care to avoid blunders in plotting.
(1) The scale values may be multiplied by any common factor. A factor of
2 or 4 is easiest to deal with. This operation preserves cycle length, but
shifts the cycles along the axis. This can be useful when the data spans only
one factor of 10, but would fall in two adjacent decades. See Fig. 7.11.
(2) The scale values may be raised to any common power. This expands
or contracts the cycle size. This can be useful when you need two cycle
paper but have only one cycle paper. Raise all of the values printed along
the scale to the second power. See Fig. 7.12. This should be considered
strictly an emergency expedient, never acceptable in a graph intended for
publication.
Fig. 7.11.
Fig. 7.12.
Another emergency trick is to splice the paper. Suppose you had data that spanned only one factor of 10
but spanned two cycles of the paper. For example, the values might range from 45 to 312. If you used
two cycle paper, this graph would occupy less than half of the paper. If you cut one cycle paper at the "4"
mark, it could be spliced together so that it reads from 40 to 400.
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
6/7
11/16/12
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
www.lhup.edu/~dsimanek/scenario/errorman/graphs2.htm
7/7