Professional Documents
Culture Documents
NDT 6946-6-44-0016 Rev1
NDT 6946-6-44-0016 Rev1
DESTRUCTIVE EXAMINATION
REQUIREMENTS OF PIPING
6946-6-44-0016 Rev. 1
Page 1 of 20
JOB SPECIFICATION
FOR
NON DESTRUCTIVE EXAMINATION
REQUIREMENT OF PIPING
Client
NRL
Project
DQUP, NRL
Location
NUMALIGARH
Job No.
6946
26.11.08
LJ
VKS
VKB
30.06.08
LJ
VKS
SC
Rev.
No
Date
Purpose
Prepared by
Checked by
Approved by
6946-6-44-0016 Rev. 1
Page 2 of 20
Abbreviations:
DP/LP
MP
CS
AS
SS
ASTM
ASME
IBR
PMS
:
:
:
:
:
:
:
:
:
6946-6-44-0016 Rev. 1
Page 3 of 20
CONTENTS
Sl. No.
TITLE
1.
GENERAL
2.
VISUAL EXAMINATION
3.
4.
PAGE
1.
GENERAL
1.1
SCOPE
6946-6-44-0016 Rev. 1
Page 4 of 20
This specification covers the general requirements for non destructive examination of shop &
field fabricated piping.
1.2
ASME Boiler & Pressure Vessel Codes, Section V & VIII (Div.1) including addenda.
b)
ASME B31.3
c)
d)
ASTM E10
e)
f)
g)
h)
i)
j)
2.
VISUAL EXAMINATION
2.1
Weld shall be visually inspected wherever accessible in accordance with the following
requirements :
a)
Internal misalignment
1.5 mm or less
b)
Not permitted
c)
Incomplete penetration
(For other than 100%
radiography butt-weld)
d)
Not permitted.
e)
6946-6-44-0016 Rev. 1
Page 5 of 20
f)
2.5 mm or less.
g)
2.5 mm or less.
h)
2.5 mm or less.
I)
Unevenness of bead
2.0 mm or less.
j)
Weld undercutting
k)
Overlap
1.5 mm or less
l)
Bead deflection
2.5 mm or less
m)
External weld reinforcement and internal weld protrusion (when backing rings are not
used) shall be fused with and shall merge smoothly into the component surfaces. The
height of the lesser projection of external weld reinforcement or internal weld
protrusion from the adjacent base material surface shall not exceed the following
limits unless specified otherwise by Licensor/Owner/EIL for some special services:
n)
1.6
3.2
4.0
4.8
o)
Flattening
Flattening of a bend, as measured by difference between the nominal outside diameter
and minimum or maximum diameter at any cross section shall not exceed 5 % of the
nominal outside diameter of pipe.
p)
2.2
Welds having any of imperfections which exceed the limitations specified in various clauses
of 2.1 shall be repaired by welding, grinding or overlaying etc. Number of times of repair
welding for the same weld, however shall conform to applicable notes to Table 1- Note
6(b)b.5.
6946-6-44-0016 Rev. 1
Page 6 of 20
3.
3.1
The type and extent of weld examination shall be in accordance with Table-1. All visual and
supplementary methods of girth weld examination shall be in accordance with ASME B31.3
and the requirements of this specification.
3.2
Welds between dissimilar materials shall be examined by method & to the extent required for
the material having the more stringent examination.
3.3
Certain categories of critical piping are classified under inspection Class IV (100%
radiography) as follows:
a)
High Pressure
b)
Severe Cyclic
c)
Low Temperature
d)
Critical Service
e)
High Alloys
f)
High Temperature
Above 5000C
CATEGORY D
FLUID SERVICE
SERVICE
INSPECTION
CLASS
---
34
CUPRO
NIKEL
AUSTENIC
S.S.
HDPE
P. NO.
CARBON STEEL
METERIAL
(NOTE 3)
-29
TO
60
-29
TO
186
0
TO
186
TEMP.
DEG. C
150#
UPTO
10.55
KG/CM2
---
---
---
A3A,
A91A,J2A
b)
LP (NOTE4,6,9)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
---
100%
GIRTH
BUTT
WELD
---
100%
10
---
100%
11
10%
100%
12
10%
100%
13
LP TEST NOT
APPLICABLE
TO NONMETALLIC
CLASSES
14
REMARK
6946-6-44-0016 Rev. 1
Page 7 of 20
a) ALL SERVICES
COVERED UNDER
INSPECTION CLASS
I, BUT, EXCEEDING
CATEGORY 'D' PR./
TEMP LIMITATION.
II
b)
ALL SERVICES OTHER
THAN THOSE
COVERED UNDER
INSPECTION CLASS-I
BUT NON -TOXIC,
NOT SUBJECTED TO
SEVERE CYCLIC
CONDITIONS.
SERVICE
INSPECTION
CLASS
CARBON STEEL
(IBR)
CARBON STEEL
METERIAL
(NOTE 3)
P. NO.
-29 TO
400
TEMP.
DEG. C
150#
A2A
d)
HARDNESS
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
A1A , A15A, a)
A20A, A32A, VISUAL
A94A, A9A
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
INSPECTION CLASS: II
NOTE 7
---
10%
100%
GIRTH
BUTT
WELD
NOTE 7
10%
---
100%
10
NOTE 7
---
---
100%
11
NOTE 7
10%
---
100%
12
NOTE 7
50%
50%
100%
13
FOR A94A
FIRE WATER
SERVICE
NOTE 12 IS
ALSO
APPLICALBE
14
REMARK
6946-6-44-0016 Rev. 1
Page 8 of 20
III
INSPECTION
CLASS
CARBON STEEL
METERIAL
(NOTE 3)
ALL GENERAL
SERVICES EXCEPT
THOSE SUBJECT TO
SEVERE CYCLIC
CONDITIONS.
CARBON STEEL
(IBR)
CARBON STEEL
KILLED CARBON
b) FLAMMABLE/
NON FLAMMABLE & STEEL
TOXIC/ NON-TOXIC;
NOT SUBJECT TO
SEVERE CYCLIC
CONDITIONS.
.
SERVICE
P. NO.
150#
TO
600#
300#
TO
600#
-29
TO
427
150#
B2A,D2A
B1A, B9A,
D1A, D21A
---
---
NOTE 7
---
c)
MP/LP (NOTE
4,6,11)
d)
HARDNESS
20%
100%
GIRTH
BUTT
WELD
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
-45
TO
204
ABOVE29
TEMP.
DEG. C
NOTE 7
20%
---
100%
10
NOTE 7
---
---
100%
11
NOTE 7
20%
---
100%
12
NOTE 7
---
100%
100%
13
FOR B2A,
D2A IBR
SEVICE NOTE
8 IS ALSO
APPLICABLE
14
REMARK
6946-6-44-0016 Rev. 1
Page 9 of 20
III(CONTD)
INSPECTION
CLASS
ALL GENERAL
SERVICES EXCEPT
THOSE SUBJECT TO
SEVERE CYCLIC
CONDITIONS.
SERVICE
1 2 Cr Mo STEEL
(IBR)
P. NO.
1 TO 2 Cr Mo.
STEEL
0.5 Cr 0.5 Mo
STEEL
C 0.5Mo STEEL.
METERIAL
(NOTE 3)
ABOVE
-29
TEMP.
DEG. C
150#
TO
600#
D2D
d)
HARDNESS
c)
MP/LP (NOTE
4,6,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
NOTE 7
---
20%
100%
GIRTH
BUTT
WELD
NOTE 7
20%
---
100%
10
NOTE 7
---
---
100%
11
NOTE 7
20%
---
100%
12
NOTE 7
---
100%
100%
13
14
REMARK
6946-6-44-0016 Rev. 1
Page 10 of 20
III(CONTD)
INSPECTION
CLASS
ALL GENERAL
SERVICES EXCEPT
THOSE SUBJECT TO
SEVERE CYCLIC
CONDITIONS.
SERVICE
3.5 Ni STEEL
AUSTANIC
STAINLESS STEEL
P. NO.
STEELS WITH
Cr > 2%
& < 5%
METERIAL
(NOTE 3)
-29
TO
500
-29
TO
371
-80
TO
120
ALL
TEMP.
DEG. C
300#
TO
600#
150#
150#
TO
600#
B1K, B21N,
B22K, D1K
A1K, A1N
d)
HARDNESS
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
NOTE 7
---
20%
100%
GIRTH
BUTT
WELD
NOTE 7
20%
---
100%
10
NOTE 7
---
---
100%
11
NOTE 7
20%
---
100%
12
NOTE 7
---
100%
100%
13
NOTE-7 FOR
HARDNESS IS
NOT VALID
FOR P.NO. 1,
8&9
14
REMARK
6946-6-44-0016 Rev. 1
Page 11 of 20
III(CONTD)
INSPECTION
CLASS
ALL GENERAL
SERVICES EXCEPT
THOSE SUBJECT TO
SEVERE CYCLIC
CONDITIONS.
SERVICE
35
ALUMINIUM
BRONZE
---
31
COPPER &
COPPER BASE
ALLOY
OTHER NON
FERROUS ALLOYS
21
TO
25
P. NO.
ALUMINIUM &
ALUMINIUM BASE
ALLOY
METERIAL
(NOTE 3)
ALL
TEMP.
DEG. C
150#
---
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
---
20%
100%
GIRTH
BUTT
WELD
20%
---
100%
10
---
---
100%
11
20%
---
100%
12
---
100%
100%
13
14
REMARK
6946-6-44-0016 Rev. 1
Page 12 of 20
IV
INSPECTION
CLASS
ALL SERVICES
SERVICE
CARBONE STEEL
(IBR)
CARBON STEEL
METERIAL
(NOTE 3)
P. NO.
ALL
TEMP.
DEG. C
ABOVE
600#
---
G22A
d)
HARDNESS
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
INSPECTION CLASS: IV
NOTE 7
---
100%
100%
GIRTH
BUTT
WELD
NOTE 7
100%
---
100%
10
NOTE 7
10%
---
100%
11
NOTE 7
100%
---
100%
12
NOTE 7
---
100%
100%
13
14
REMARK
6946-6-44-0016 Rev. 1
Page 13 of 20
ALL GENERAL
SERVICES
IV (CONTD..)
SERVICE
INSPECTION
CLASS
1
4
KILLED CARBON
STEEL
1 TO 2 Cr STEEL
(IBR)
5 Cr 9 Cr Mo
STEEL
C 0.5 Mo STEEL
12 Cr
( TYPE 410 SS)
P. NO.
METERIAL
(NOTE 3)
ALL
UPTO -45
ALL
TEMP.
DEG. C
ABOVE 600#
ALL
150# TO
600#
ABOVE 600#
B4F
d)
HARDNESS
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
NOTE 7
---
100%
100%
GIRTH
BUTT
WELD
NOTE 7
100%
---
100%
10
NOTE 7
10%
---
100%
11
NOTE 7
100%
---
100%
12
NOTE 7
---
100%
100%
13
14
REMARK
6946-6-44-0016 Rev. 1
Page 14 of 20
IV (CONTD...)
INSPECTION
CLASS
METERIAL
(NOTE 3)
ALL SERVICE
SPECIAL SERVICES
( NACE,O,H,
CAUSTIC)
SPECIAL SERVICES
( NACE,O,H,
CAUSTIC)
SERVICES SUBJECT
TO SEVERE CYCLIC
CONDITIONS.
NI ALLOY
3.5 NI STEEL
SPECIAL SERVICES
( NACE,O,H,
CAUSTIC)
SERVICE
45
41,42,43
1,3,4,5
P. NO.
ALL
TEMP.
DEG. C
ALL
6
a)
VISUAL
G49Q
---
---
---
---
d)
HARDNESS
c)
MP/LP (NOTE
4,6,10,11)
A19A, A22A,
A23A, A5A, b)
B21A, B22A, RADIOGRAPHY
B23A, B25A, (NOTE 5,6)
B26A, B5A,
B5D, D26A,
D5A, D5D,
E25A, F25A,
F25D, F26D,
F27A
---
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
NOTE 7
---
100%
100%
GIRTH
BUTT
WELD
NOTE 7
100%
---
100%
10
NOTE 7
10%
---
100%
11
NOTE 7
100%
--
100%
12
NOTE 7
---
100%
100%
13
EXTENT OF
HARDNESS
TEST FOR
CLASSES
A19A, A22A,
A23A, B21A,
B22A, B23A,
F27A IS 100%
EXTENT OF
HARDNESS
TEST FOR
CLASSES
A5A, B25A,
B26A, B5A,
D26A, D5A,
E25A, F25A
IS 10%
(NOTE-16)
NOTE-7 FOR
HARDNESS IS
NOT VALID
FOR P. NO.9
14
REMARK
6946-6-44-0016 Rev. 1
Page 15 of 20
IV (CONTD...)
INSPECTION
CLASS
ALL
>500
HIGH TEMP.
SREVICES
ALL
ALL
ABOVE 600#
ALL
ALL
c)
MP/LP (NOTE
4,6,10,11)
b)
RADIOGRAPHY
(NOTE 5,6)
a)
VISUAL
F59V
B25K, F15M,
G25N, G57M,
G5M
d)
HARDNESS
---
A2K
---
PRESSURE
APPLICABLE TYPE OF
CLASS
PIPING CLASS EXAMINATION
B16.5/B16.34
GENERAL SERVICES
ALL
TEMP.
DEG. C
150#
300#&600#
P. NO.
BELOW
-45
AUSTENITIC
STAILESS ATEEL
METERIAL
(NOTE 3)
LOW TEMPERATURE
SERVICE
SERVICES SUBJECT
TO SEVERE CYCLIC
CONDITIONS.
SERVICE
NOTE 7
---
100%
100%
GIRTH
BUTT
WELD
NOTE 7
100%
---
100%
10
NOTE 7
10%
---
100%
11
NOTE 7
100%
--
100%
12
NOTE 7
---
100%
100%
13
REFER NOTE
15 FOR
FERRITE
MEASUREME
NT TEST FOR
CLASSES
B25K, F15M,
G25N, G57M,
G5M AND
SHALL BE
100%
14
REMARK
6946-6-44-0016 Rev. 1
Page 16 of 20
6946-6-44-0016 Rev. 1
Page 17 of 20
Branch welds shall consist of the welds between the pipe & reinforcing element (if any),
nozzles & reinforcing element and the pipe & nozzle under the reinforcing element.
Reinforcing element to be interpreted as pads, saddles, weldolets, sockolets etc.
2.
Seal welds of threaded joints shall be given the same examination as socket welds.
3.
4.
Magnetic Particle & Liquid Penetrant method of examination shall be in accordance with
Section V of the ASME Boiler and Pressure Vessel Code, Article VII and VI respectively.
The entire area of the accessible finished weld surface shall be examined. Selected root runs,
subject to a maximum of 10%, before finished weld, may also be examined, at the discretion
of the engineer-in-charge.
5.
a)
b)
"Random 10%" of Liquid Penetrant / Magnetic Particle test shall mean testing, by
applicable test, one weld for each ten welds or less made by the same welding
procedure or operator or both. Similarly "Random 20%" shall mean testing, by
applicable test, one weld for each five welds or less made by the same welding
procedure or operator or both.
c)
When Liquid Penetrant examination is specified, the surface shall be free of peened
discontinuities. Abrasive blast cleaning shall be followed by light surface grinding
prior to Liquid Penetrant examination.
d)
Inspection shall be performed in the welds excluding those for which radiography has
been done.
e)
Girth weld, branch weld, attachment weld & socket weld of 3-1/2 Ni steel shall be
Liquid Penetrant tested only when welded with austenitic material where MP test has
been specified.
Radiography :
a)
"Random 10% or 20% radiography" shall mean examining not less than one from
each 10 welds or less in case of "Random 10% radiography" or one from each five
welds or less in case of "Random 20% radiography" made by the same welding
procedure or welder or both. Irrespective of percentage, no. of welds to be
radiographed shall be minimum 1. However first two welds made by each welder
shall also be radiographed in case of "Random radiography". Welds selected for
examination shall not include flange welds and shall be radiographed for their entire
length. However, where it is impossible or impracticable to examine the entire weld
length of field welds for either random or 100% radiography, and if the same
impossibility is agreeable to EIL site-in- charge, then a single 120 deg. exposure of
the weld length may be given a Magnetic Particle test or Liquid Penetrant test.
However in such cases for ferro-magnetic materials, only MP test shall be acceptable
for classes higher than 600#.
6.
6946-6-44-0016 Rev. 1
Page 18 of 20
b)
c)
Number of radiographs per one circumferential weld shall be as per ASME Sec.V
Articles 2 and 22.
When radiography or other non destructive inspection is specified, acceptance criteria for
repairs or defects shall be as follows:
a)
b)
Two additional examinations of same type shall be made of the same kind of
item (if welded joint, then by the same welding procedure or operator or
both).
b.2
b.3
b.4
If all the items examined as required by b.3 are acceptable, the items requiring
repair shall be repaired or replaced and reexamined as required, and all items
represented by this further examination shall be accepted.
b.5
Number of times repair welding could be done for the same weld before
acceptance shall be as follows:
Material
3 or less
2 or less
Killed steel
2 or less
2 or less
Austenitic S.S.
2 or less
3.5 Ni steel
2 or less
2 or less
2 or less
Others
2 or less
7.
6946-6-44-0016 Rev. 1
Page 19 of 20
b.6
Welds not found acceptable for allowed number of times of repair as per b.5
above shall be replaced and reexamined.
b.7
Hardness Test :
a)
Hardness test for each weld (unless mentioned otherwise in NDT Table-I ) shall be in
accordance with ASTM specification E10, ASME B31.3 and as called for in NDT
Table-I/PMS(Piping Material Specification), and shall be made after final heat treatment (wherever heat treatment is specified in welding specification). All welds which
are given heat treatment shall be hardness tested. A minimum of 10% of welds of hot
formed and hot bent materials in each heat treatment batch which are furnace heat
treated and 100% of those which are locally heat treated, shall be hardness tested. The
hardness limit applies to the weld and heat affected zone. Hardness tests of the heat
affected zone shall be made at a point as near as practicable to the edge of the weld.
One test per weld shall be performed.
b)
Hardness test where specifically called out in Table-I of this specification or in PMS,
shall be carried out irrespective of thickness and to the extent (%age) as mentioned
therein.
c)
d)
e)
Maximum
Hardness
(BHN/RC)
CS
238BHN/RC22
CS (NACE, H2 service)
200BHN
225BHN
Cr 0.5% or less
225BHN
225BHN
Cr 2.25%-3%(C 0.15%)
241BHN
241BHN
241BHN
DUPLEX SS (NACE)
RC28
In case hardness values are mentioned in both welding specifications (69466-77-0005) & table given in Note-7(d), the lower of the two values shall be
applicable.
8.
6946-6-44-0016 Rev. 1
Page 20 of 20
For IBR service lines, following IBR requirements shall apply in addition to the notes 4, 5, 6,
7, 12 and Table I. In case of conflict between above notes and these requirements, the more
stringent ones shall apply. IBR piping shall be erected of IBR inspector approved material and
construction procedure. Erected piping shall be hydrotested, inspected and approved by IBR
inspector.
a)
b)
Piping 102 mm (4") bore and under, but not less than 38 mm (1-1/2") bore :
Two percent of welds made by each welder on a pipeline with a minimum of one weld
per welder, selected at random, shall be subjected to radiography or may be cut for
visual examination and tests.
c)
d)
Retests :
If any test specimen is unsatisfactory, two further weld specimens for retests shall be
selected from the production welds and subjected to tests. In the event of failure of
any retest specimens, the production welds carried out by this welder subsequent to
the previous test shall be given special consideration.
9.
For fabricated fittings LP test shall be done on the final pass of welding only, in addition to
visual examination.
10.
For mitres and fabricated reducers, LP / MP test shall be done on root pass in addition to
radiography applicable to circumferential joint of respective piping class.
11.
For branch connections, LP/MP test shall be done on root pass and final pass.
12.
As per TAC requirements, 10% of the butt weld joints shall be radiographed, however, 50% of
these butt weld joints shall be field weld joints.
13.
In lines where weld joints are subjected to Stress relieving , Radiography/any NDT for
acceptance of the joint as required by the specification shall be carried out only after stress
relieving.
14.
For lined specs, testing (MP/LP/Radiography etc.) shall be performed before lining.
15.
Weld deposits should be checked for ferrite content. A Ferrite Number (FN) not less than 3 %
and not more than 10 % is required to avoid sigma phase embrittlement during heat treatment.
FN shall be determined by Ferritescope or may be calculated using Schaffler or DeLong
diagrams (the DeLong diagram should be used if FCAW welding is performed), prior to post
weld heat treatment.
16.
Hardness test for welds of all classes of Hydrogen service of carbon steel (for thickness under
19 mm) is required and it is 10%.