Professional Documents
Culture Documents
DSL 1504G User's Manual English V2.9 20121101
DSL 1504G User's Manual English V2.9 20121101
SHDSL Router-DSL-1504G
Users Manual
G.SHDSL Router-DSL-1504G Version 2.9
Table of Contents
1. PRODUCT OVERVIEW 25
1.1 PREFACE 25
1.2 OVERVIEW 25
2. HARDWARE INSTALLATION 26
2.1 FRONT PANEL LEDS INDICATORS 26
2.2 REAR PANEL CONNECTORS 26
2.3 INSTALLATION PROCEDURE 27
3. CONSOLE 28
3.1 CONSOLE SETUP 28
3.2 LOGIN 29
3.3 COMMAND 29
3.3.1 login admin 30
3.3.2 login root30
4. APPLICATION 37
4.1 BRIDGE 37
4.2 ROUTER 38
5. CONFIGURING WITH WEB 39
5.1 LOGIN 39
5.2 WEB MENUS 40
5.3 STATUS 40
5.3.1 System Information 40
5.3.2 DSL 40
5.3.3 ATM 41
5.3.4 LAN 42
5.3.5 Routing Table 42
5.4 QUICK SETUP 43
5.5 BASIC CONFIGURATION 44
5.5.1 LAN 44
5.5.2 WAN 47
5.5.3 DSL 50
5.6 BRIDGE VIRTUAL INTERFACE CONFIGURATION 50
5.7 ADVANCE CONFIGURATION 52
5.7.1 Routing 52
5.7.2 DHCP Relay53
5.8 FIREWALL 54
5.8.1 Port Forwarding 54
5.8.2 VPN Passthrough 54
5.9 SYSTEM 55
5.9.1 Configuration 55
5.9.2 DNS Configuration 55
5.9.3 Management 55
5.10 ADMIN 60
5.10.1 FACTORY DEFAULT 60
5.10.2 SAVE CONFIGURE 60
5.10.3 REBOOT DEVICE 60
5.10.4 UPGRADING FIRMWARE 61
5.10.4.1 Upgrade using webpage61
5.10.4.2 Upgrade using Ethernet port 61
5.11.3 Upgrade using Serial port 63
G.SHDSL Router-DSL-1504G Version 2.9
APPENDIX 70
APPENDIX A:INSTALL TFTP SOFTWARE70
G.SHDSL Router-DSL-1504G Version 2.9
1. Product Overview
1.1 Preface
The primary objective of this manual is to help network administrator operate GSHDSL bridge
and router product. Strongly committed to user friendly, this manual will guide the users step by
step to turn the product up and running in the simplest way ever.
1.2 Overview
With the symmetrical data transmission up to 5.7 Mbps over the ordinary telephone line, SHDSL
satisfies the needs of multiple user of small office/home office (SOHO), who needs both
bandwidth and permanent data connection. Although SHDSL transmits data over the telephone
line, it does not interrupt the voice because it uses different frequency for data transmission.
Therefore, the end-users are able to access internet and to talk over the telephone
simultaneously.
GSHDSL is designed to provide user all features needed in the SOHO environment. This product
supports multiple virtual channels to connect to different location. Bridge and router features are
also supported in GSHDSL.
25
G.SHDSL Router-DSL-1504G Version 2.9
2. Hardware Installation
2.1 Front Panel LEDs Indicators
There are eight LED indicators on the front panel of GSHDSL. They show the statuses of the
device.
Figure 1 The functions of LED indicators are described in the following table
The rear panel connectors connecting the device to the LAN and xDSL network are illustrated as
below.
NotePress the RESET button for more than 5 seconds, the device will be loaded to
factory default and reset automaticlly.
26
G.SHDSL Router-DSL-1504G Version 2.9
Step 2. - Use RS-232 cable to connect the console port of the device to serial port of the PC with
terminal emulator software installed.
Step 3. - Use RS-45 cable to connect the device and the PC which has the Network Interface
Card (NIC) installed. If you want to connect to an external hub, you have to use the RJ-45 cross-
over cable.
Step 4. - Plug in the Power adaptor to the DC Power socket of the device, then connect the
Power adaptor to the AC outlet.
27
G.SHDSL Router-DSL-1504G Version 2.9
3. Console
3.1 Console Setup
Step 1: Connect computer to the device through the console port as shown in the figure 1.
Step 2: Open the terminal emulator software (like Hyper-Terminal on Microsoft Windows machine,
or Minicom on Linux machine), then select the proper COM port for the connection. Set the
terminal and port to the following parameters:
Turning on the GSHDSL, then after few seconds of machine initialization, the system
management terminal will display the login screen.Details Figure 2.
28
G.SHDSL Router-DSL-1504G Version 2.9
3.2 Login
3.3 Command
GSHDSL>
Command Comments Format
list Print command list list
Login to configure the login admin
login
device login root
29
G.SHDSL Router-DSL-1504G Version 2.9
30
G.SHDSL Router-DSL-1504G Version 2.9
Enter configuration
configure configure
mode
exit Exit current mode exit
hostname Set hostname of system hostname WORD
list Print command list list
load Load configuration file load default
Logout the
logout logout
configuration
Maintenance shell
main-shell main-shell
command
ping send echo messages ping WORD
reboot Reboot the system reboot
save Save configuration file save
show logging dsl
show logging dsl lines <1-100>
show logging ppp
show logging ppp lines <1-100>
show routing
show routing ipv4
show running
show running atm
show running bvi
show running dsl
show running ether
show running firewall
show running routing ipv4
show Show configuration show running routing rip
show running snmp
show running system
show running tr069
show snmp
show status dsl
show status ethernet
show status atm
show status atm vc <1-32>
show status bvi
show status bvi <1-12>
show system dhcp-relay
show system info
show tr069
sync Synchronize element sync time
Trace route to
traceroute traceroute WORD
destination
31
G.SHDSL Router-DSL-1504G Version 2.9
3.3.2.1 Configure
GSHDSL# configure
GSHDSL(config)#
Command Comments Format
End mode and down to top
end end
mode
exit Exit current mode exit
list Print command list list
no set atm vc <1-32>
Negate the configuration of
no no set bvi <1-12>
element
no set routing ipv4 <1-50>
password admin old-password WORD
new-password WORD
password Change password
password root old-password WORD
new-password WORD
set atm vc <1-32>
set bvi <1-12>
set dsl
set ether
Select the element to set firewall
set
configure set routing ipv4 <1-50>
set routing ripd
set snmp
set system
set tr069
32
G.SHDSL Router-DSL-1504G Version 2.9
3.3.2.1.1.1 interface
GSHDSL(config-atm)# interface
GSHDSL(config-atm-if)#
Command Comments Format
end End mode and down to top mode end
exit Exit current mode exit
ipv4 Local IPv4 address ipv4 A.B.C.D/M
list Print command list list
nat Network Address Translation of this nat enabled
ATM interface
no Negate the configuration of element no nat enabled
peer-ip Peer IPv4 address peer-ip A.B.C.D
33
G.SHDSL Router-DSL-1504G Version 2.9
stp enabled
stp Spanning Tree Protocol
stp priority <0-65535>
34
G.SHDSL Router-DSL-1504G Version 2.9
35
G.SHDSL Router-DSL-1504G Version 2.9
36
G.SHDSL Router-DSL-1504G Version 2.9
4. Application
4.1 Bridge
In Bridge, GSHDSL provides frame forward services between two or more LANs. It forwards
frames based on the MAC (Medium Access Control) addresses which is hardware-level of NICs
(Network Interface Card).
The Encapsulation of the system must set to RFC2684 bridge. To change the Encapsulation,
please see the section 5.5.2.1.
The application of the G.SHDSL Modem in Bridge are illustrated in the following figures
37
G.SHDSL Router-DSL-1504G Version 2.9
4.2 Router
The Encapsulation of the system must set to RFC2684 routed. To change the Encapsulation,
please see the section 5.5.2.1.
The application of the G.SHDSL Modem in Router mode are illustrated in the following figures
38
G.SHDSL Router-DSL-1504G Version 2.9
When connected, the GSHDSL has the following pre-configured host IP addresses
192.168.0.1as shown below.
Configure your PC to the same network segment as the GSHDSL. For example, you could
set the PC to IP address 192.168.0.10 with a subnet mask of 255.255.255.0.
Connect the PC to any of LAN port designated 1, 2, 3 or 4 on the Front Panel.
Open the Web browser.
Enter the IP address of the GSHDSL.in the address field of the browser as example:
https://192.168.0.1 and then press <Enter> to connect.
There is a default User Name root for the GSHDSL.
39
G.SHDSL Router-DSL-1504G Version 2.9
5.3 Status
Menu System Information allows you to view and verify the units identity information as shown
below.
In this menu, it shows the current system information such as: System Name, Model, Firmware
Version, Device up time, DSL up time and DSL status.
Items Description
Hostname : Display the name of the unit.
Model Name : Display the model name of the unit.
Firmware Version : Display the current software version.
Device uptime : Display the system runing time
DSL uptime : Display the time of DSL get sync
DSL status of port1 : Line status of DSL port.
5.3.2 DSL
Display the DSL Performance and Statistics. You can see the information of Line
Code,Standard,Service mode,Attenuation,and Line Status.
40
G.SHDSL Router-DSL-1504G Version 2.9
Items Description
Version : Display the version of DSL driver
Standard : Display the standard type of DSL
Service mode : Display the Service mode of DSL
Attenuation : Display the attenuation of DSL
Signal-to-Noise
: Display the SNR of DSL
Ratio(SNR)
Power back-off : Display power back-off status
Tx Power : Display the Tx Power of DSL
Dying Gasp : Display the dying gasp of remote device
DSL info : Display DSL information
port 1 status : Line status of DSL port 1
5.3.3 ATM
Displaying ATM Performance and Statistics.You should creat ATM channels in Basic
ConfigurationWANATM Channel, please see the section 4.4.2.1. then you can look them
status.
If the VC is already activated, then in the Status field it displays the word Up, otherwise it
displays Down or Connecting .
If the VC set with the encapsulation type of PPPoE or PPPoA, then in the Status field it displays
the status of PPP connection: Down, Connecting or Connected.
41
G.SHDSL Router-DSL-1504G Version 2.9
Items Description
Description : Display the description of ATM channel
VC Index : Display the VC Index of ATM channel
VPI/VCI : Display the VPI/VCI of ATM channel
Encapsulation : Display the encapsulation of ATM channel
IP address : Display the WAN IP of ATM channel
MTU : Display the MTU of ATM channel
Rx/Tx(bytes) : Display the Rx/Tx of ATM channel
Status : Display the status of ATM channel
5.3.4 LAN
Display the LAN Performance and Status. You can see the information of IP Address, and the status of
per PHY port.
Items Description
IP address : Display the IP address of LAN
IPv6 link Display physical address
IPv6 address Display IPv6 address
MTU : Display the MTU of LAN port
Rx/Tx packets : Display the Rx/Tx packets of LAN port
Rx/Tx bytes : Display the Rx/Tx bytes of LAN port
Rx/Tx dropped : Display the Rx/Tx dropped of LAN port
MAC address : Display the MAC address of LAN
Connectivity mode : Display the connectivity mode of LAN port
Port status : Display the port status of LAN port
42
G.SHDSL Router-DSL-1504G Version 2.9
Items Description
Target IP : Display target IP of routing
Device/Gateway : Display Device/Gateway of routing
Source IP/Interface : Display Source IP/Interface of routing
Using this setup, the device can be quickly configured and operated properly.
Note: The WAN configuration is for the first Virtual Circuit ( VC 1 ) in thirty two VC set available in
the device.
43
G.SHDSL Router-DSL-1504G Version 2.9
no space in between
: Channel Index The numeric index of creation 0 - 32
: VPI Virtual Path Identifier, given by ISP 0-8
ATM Channel : VCI Virtual Channel Identifier, given by 32 - 4096
parameters ISP
The encapsulation type is given by RFC2684 routed/
: Encapsulation ISP. Select from the drop-down list. RFC2684 bridge/
PPPOE/PPPOA/IPOA
Default: PPPOE
The WAN local IP Address of i.e 123.221.79.2
: Local IP Address router, given by ISP Default:
0.0.0.0
: Subnet Mask The WAN local IP subnet mask of i.e 255.0.0.0
router, given by ISP Default:
255.255.255.0
: Peer IP Address i.e 229.122.79.32
The IP Address of DSLAM, given
Default:
by ISP
0.0.0.0
WAN OPTION : NAT Enable Network Address
Translation (NAT) if you want all Enable/Disable
system behind the LAN sharing a Default:Disable
single local IP address of this
channel
: Username ISP login user name, given by ISP.
It is set for the encapsulation type NA
of PPPoE or PPPoA
: Password ISP login password, given by ISP. It
is set for the encapsulation type of NA
PPPoE or PPPoA
: Default route Enable this if you want all un-
defined IP traffic will go outside via Enable/Disable
PPP OPTION this channel. Enable default Router Default:Disable
if you design your device as a
gateway
: MTU Maximum Transmit Unit in bytes 64-2000
over PPP link Default:1492
In menu Basic Configuration, the system can be configured in individual submenu: LAN setup,
WAN setup and DSL.
5.5.1 LAN
5.5.1.1 Configuration
In LAN configuration Setup, it contains the LAN related configuration such as:IPv4, Subnet Mask,
Connectivity Mode.
44
G.SHDSL Router-DSL-1504G Version 2.9
64~2000
MTU Maximum Transmission Unit Default 1500
45
G.SHDSL Router-DSL-1504G Version 2.9
5.5.1.2 VLAN
46
G.SHDSL Router-DSL-1504G Version 2.9
5.5.2 WAN
In menu WAN Setup, it can shows the list of Virtual Circuits (VCs):channel 1 to channel 32.
If a VC is already configured then it display its parameters as Channel Description, VPI,VCI,
Encapsulation, and so on.
Because the firmware support IRB. It means you can perform Bridge and Router function at the
same time.
47
G.SHDSL Router-DSL-1504G Version 2.9
48
G.SHDSL Router-DSL-1504G Version 2.9
49
G.SHDSL Router-DSL-1504G Version 2.9
5.5.3 DSL
50
G.SHDSL Router-DSL-1504G Version 2.9
If you set RFC2684-bridged encapsulation in wan configuration webpage, you need to create BVI
interface and add both LAN and ATM VC into that BVI , it means you create a Bridge for LAN and
ATM channel.
51
G.SHDSL Router-DSL-1504G Version 2.9
5.7.1 Routing
5.7.1.1 Static
Static routes are user-defined routes that force packets moving between a source and a
destination to take a specific path.
5.7.1.2 Dynamic
5.7.1.2.1 RIP
A router running RIP can receive a route via an update from another router running RIP.
52
G.SHDSL Router-DSL-1504G Version 2.9
53
G.SHDSL Router-DSL-1504G Version 2.9
5.8 Firewall
54
G.SHDSL Router-DSL-1504G Version 2.9
5.9 System
5.9.1 Configuration
5.9.3 Management
5.9.3.1 TR069
55
G.SHDSL Router-DSL-1504G Version 2.9
TR-069 (short for Technical Report 069) is a DSL Forum (which was later renamed as Broadband
Forum) technical specification entitled CPE WAN Management Protocol (CWMP). It defines an
application layer protocol for remote management of end-user devices.
Now our CPE can access to ACS automatically and send periodic information with the interval
time configured by customer. Then ACS can get the detailed information of CPE, such as the
hardware version, the software version and so on. ACS also can set some parameters through
the protocol, like periodical interval. Our customer can try every parameter. But now we have not
implemented all functions. So some parameters only can be get, not can be set. We will
accomplish all functions as soon as possible.
56
G.SHDSL Router-DSL-1504G Version 2.9
57
G.SHDSL Router-DSL-1504G Version 2.9
5.9.3.2 SNMP
58
G.SHDSL Router-DSL-1504G Version 2.9
Community
Read-Only Community:
Specify the community name of external SNMP Managers allowed with access level of
Read to the units MIB.
Read-Write Community:
Specify the community name of external SNMP Managers allowed with access level of
Read & write to the units MIB.
Trap
To configure the Trap, go through the following steps.
Select the version number, SNMPv1 or SNMPv2, from the pull-down menu.
Specify the IP address of each SNMP Trap Manager in the correspondent Destination IP.
Click the Apply button to save the configuration.
59
G.SHDSL Router-DSL-1504G Version 2.9
5.9.3.3 Time
5.10 Admin
5.10.1 Factory Default
If you click OK to re-load factory default, the device will reboot by itself.
If you click OK to save the new configuration, the device will save the current configuration.
If you click OK to reboot the device, the device will reboot by itself.
60
G.SHDSL Router-DSL-1504G Version 2.9
Step 8:You can type the command printenv to see whether you have made the correct IP
address changes.
61
G.SHDSL Router-DSL-1504G Version 2.9
62
G.SHDSL Router-DSL-1504G Version 2.9
Step 12:After loading file, type erase 2840000 2cfffff to erase the old file in the flash.
Step 13:Type cp.b 100000 2840000 $(filesize) to burn the file to the flash.
63
G.SHDSL Router-DSL-1504G Version 2.9
Step 4: Press Enter key immediately when you see this message Hit any key to stop autoboot:
then you can see the prompt =>. Enter loadb 100000 and press Enter key you can get
following screen
Step 5: Select Send File under the tools bar of Transfer as following screen.
64
G.SHDSL Router-DSL-1504G Version 2.9
Step 8: Click Open for select file to send as the following screen:
65
G.SHDSL Router-DSL-1504G Version 2.9
Step 10: Click Send you can get the following screen:
Step 11: Code in GSHDSLwill be uploaded. It will take about 18~20 minutes. The above screen
will automatically disappear after Code was completely updated and you can get the following
screen:
66
G.SHDSL Router-DSL-1504G Version 2.9
Step 13: It will take about few minutes to erase flash memory and the screen will display done
message as the following:
67
G.SHDSL Router-DSL-1504G Version 2.9
Step 14: Enter cp.b 100000 2840000 $(filesize) as the following screen:
Step 15: It will take about few minutes to copy flash memory and the screen will display done
message as the following:
Step 17: The system will automatically reboot then you can see the new version that you had
updated it before as the following screen:
68
G.SHDSL Router-DSL-1504G Version 2.9
69
G.SHDSL Router-DSL-1504G Version 2.9
Appendix
Step 1:Install the software of TFTP, double click the icon of tptpd_ftp.exe as following:
70
G.SHDSL Router-DSL-1504G Version 2.9
Step 4: Select I agree to the terms of this license agreement. and click Next to get following
screen:
71
G.SHDSL Router-DSL-1504G Version 2.9
72
G.SHDSL Router-DSL-1504G Version 2.9
Step 8: Then click Finish, The TFTP software has been installed completely.
73