Professional Documents
Culture Documents
NCC mt11075 W
NCC mt11075 W
Workbook
June 2007
MT11075 NX 5
Publication Number
mt11075_w NX 5
Proprietary and restricted rights notice
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
IS&V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
1 Libraries
In this section you will modify tool and part material libraries. You will also
enter feed and speed data to be used in generation of feedrates, spindle
speeds, depth of cut and stepover parameters.
Step 1: Create a new part file named ***_library_wb.
Step 4: Set the feed and speed parameters for the new tool and part
materials.
In the Machining Data Manager set the filters and create the new
entry. Set the Machining Data filters using your new part and
tool materials.
You will set the parameters for a 2.00 diameter tool.
Diameter 2.00
Length 4.00
Cut Depth 0.350
Stepover 1.600
SFM 750
Spindle Speed 1432
1
Feed Per Tooth .005
Cut Feed Rate 14.32
Number of Flutes 2
Step 5: Test your new feed/speed entry in NX. Create a block and use face
mill to machine it.
1-2 NX CAM Customization Workbook UGS Corp., All Rights Reserved mt11075_w NX 5
Lesson
2 Wizard Builder
2
In this section of the workbook, you will create a new Manufacturing Wizard,
the wizard will be used to create Face Mill Area operations. You will test the
wizard on an existing part.
Step 1: Open the Process Studio Author.
Create Object This step will specify the type and subtype of
operation. The parent groups will also be selected in this step.
Step 4: Customize the interface with messages and graphics as you see fit.
You can also link help files as you did in the lesson.
Step 5: Test the wizard in NX, you can use an existing part file or create a
new part.
Remember that you have not created parent groups so you should
create tools and select geometry in the parent groups before testing
the wizard.
3 Templates
In this section of the workbook, you will create a template part file and place 3
tools and operations within it.
Step 1: Create a new part file.
Step 3: Create at least 12 tools and place them in the pockets. Use the
Holder functionality to define the tool up to the gage line.
Step 4: Create at least 4 operations that you would commonly use and
customize them as you see fit.
Step 5: Set the template and load with parent options appropriately.
4 Hole Making
In this section of the workbook, you will use the HOLE_MAKING subtype to
generate operations necessary for the machining of the four counterbored
holes.
Step 4: Select the Program View of the Operation Navigator and move the
newly generated Hole Making operations into the program parent
group below the CM-INITIAL-ROUGH and SIDE-1-FINISHING
programs.
Step 5: Verify the tool path. Use the verify option to validate the tool paths
which you have just created.
4-2 NX CAM Customization Workbook UGS Corp., All Rights Reserved mt11075_w NX 5
Lesson
5 IS&V
In this section of the workbook, you will use a pre-built machine for
simulation purposes.
Step 3: Mount the manufacturing assembly to the machine tool. You will
mount the part beside the vise on the table the vise isnt used in
this setup.