Professional Documents
Culture Documents
Engineering Review Sheet Vyasi Hepp (2 X 60 MW)
Engineering Review Sheet Vyasi Hepp (2 X 60 MW)
Engineering Review Sheet Vyasi Hepp (2 X 60 MW)
Sl.No Drg. No Item of work 1. LII's/Owner's Comment 2. M/s OMIL Reply 3. LII's/Owner's Comment 4. M/s OMIL Reply 5. LII's/Owner's Comment Status
1 DGN/ 251 Design Note -Structurals Reviewed the DN and our observations are
given below for compliance:
Page 2 4. Layout Refer PDF copy and layout is missing.
2 DGN/ 250 Design Note - Layout is Noted
Mechanical incorporated at p2.
Page 1 3 A. Rope drum Refer clause 2.14.7 GC & LB
Replace IS2062 E410 Gr B by Cast steel
IS1030 Gr 340-570 W Incorporated Noted
3 Drg.No.250 General Arrangement (a) Refer Note 4 Total weight of crane =
87.6 t Incorporated Noted
Sheet 1 of 2 (b) Refer Note 6 Include hoist also. Incorporated Noted
(c ) Replace word Dogging beam by Latching
arrangement. Incorporated Noted
(d) Refer Table and include Specification for
SPECIFICATION DETAILS for VVVF
VVVF drive control for Hoist, LT & CT Incorporated OPEN
DRIVE IS NOT INCLUDED
motors.
Sheet 2 of 2 (a) Replace word Dogging beam by Latching
arrangement. Incorporated Noted
(b) Refer co-ordinate D-3. Check the
dimension 136 mm with reference to Incorporated corrected as 139 mm
Drg.no.201 Rev 2 and correct.
4 ADDITIONAL COMMENTS
a Drg. No.250 Rev 1 Gantry Rail Specify 45 kg/m CR rail as per
OPEN
IS3443 in GA Drg.No.250 Rev 1.
Page 1 of 3
Engineering Review Sheet
VYASI HEPP (2 x 60 MW)
Sl.No Drg. No Item of work 1. LII's/Owner's Comment 2. M/s OMIL Reply 3. LII's/Owner's Comment 4. M/s OMIL Reply 5. LII's/Owner's Comment Status
b DGN/251 Rev 1 Structurals Refer Sl.No.2 Mechanical
MATERIALS Strength of Proposed Materials
i. Structural Steel Specify Grade E250 BR and year
of specification 2011.
ii. Yield stress & Tensile Stress Specify clearly minimum Ys &
UTS for design calculation
iii. Carbon Steel In the Table IS2004 (Cl 4 &5) and
IS1570 (40C8, 50C4, 55C8) are
proposed.
1. Indicate only the materials OPEN
being used in the DN.
2. The values (Ys or UTS)
indicated and taken for
calculations are on higher side;
hence specify "Condition of
Supply" as per IS codal provision
providing the Reference.
c DGN/250 Rev 1 Mechanical
Components
i. Technical Input data Provide input data under Sl.No.1
Page 2 of 3
Engineering Review Sheet
VYASI HEPP (2 x 60 MW)
Sl.No Drg. No Item of work 1. LII's/Owner's Comment 2. M/s OMIL Reply 3. LII's/Owner's Comment 4. M/s OMIL Reply 5. LII's/Owner's Comment Status
d Basis of Design Cl 7.4.2 (IS 3177) Mechanism components are
checked depending on the
ultimate tensile strength by
verifying that the calculated
stress does not exceed a
permissible stress dependent on
the breaking strength of the
material used.
e Permissible Stress Cl 7.4.3 (IS 3177) Mechanism components shall be
checked for strength under case
1, II, III & IV loading conditions
and load combinations specified OPEN
in 7.3.2.
The value of the permissible
stress Fa is given by following
formula where unit stress was
defined as N/mm
Page 3 of 3