Professional Documents
Culture Documents
CAT User Manual
CAT User Manual
CAT User Manual
Preface:
Thank you for choosing our GSM/GPS Car security products. This GSM/GPS Car security product is
used in all GSM and GPS networks. It collects GPS data to realize remote control functions. With CAT-4,
your vehicle will be armed with a powerful security system and precise position information. This system
is dedicated to serve individual user. It mainly focuses on the protection of personal vehicles without any
third-party helps. You will also be able to realize fleet management through our software operations.
Before operating the terminal, please read this manual thoroughly, and retain it for future reference
in order to get the best service from the terminal and us.
Contents
Chapter One Introduction
11 Functions
12 Technical perimeters
13 Safety Instructions
42 Alert Management
Appendix
Chapter One
INTRODUCTION
11 Functions
1. Voice operation: You may call CAT-4 to configure it by following the Voice Instruction.
2. Dual Positioning: The CAT can locate your vehicle through both GPS positioning and GSM base station
positioning. So you still know where your vehicle is even when there is no GPS signal or when the GPS
antenna has been cut off.
3. Global SMS Alarm: When there is an alarm, the device will send you an alert SMS automatically.
4. Global Tracking: Wherever your vehicle is , you can track your vehicle on computer or through your cell phone
by sending SMS.
5. Remote control: You will be able to use remote control to set up alarm/ unalarmed.
6. Global Call Alarm : When there is an alarm, the device will call you immediately. You will be able to monitor
alarm.
7. Search for vehicle function: In parking lot, for example, you can activate lights to search for your car by sending
a SMS.
8. Emergency Alarm(SOS Alarm): When you are hijacked in your vehicle, you can send a SOS alert to your
families and friends by pressing a single button.
9. Ghost Hand: When a thief drives your vehicle away, you can send a SMS to your CAT which will stop it on your
demand.
10. Power Failure Alarm: When power is cut off, it will send a Power Failure Alert SMS to you automatically. Then
the backup battery will supply power to the system.
11. Door lock function:
In engine-off status, you can send a SMS to set alarm status in which the door is locked automatically.
In engine-on status, you press the brake to lock the door.
12 Technical peremeter
1. GSM module: WAVECOM S2336 GSM module. It supports AT command and TCP/IP protocol.
GSM Frequency850 /900 /1800 /1900MHz
(Up: 824 84989091517101785MH, 1850---1910MHz;
Down: 869 89493596018051850MHZ,1930---1990MHz)
3. AntennaGSM Antenna
13 Safety Instructions
1. Please do not use the device in the areas where wireless device uses are prohibited.
2. Please use the accessories in the package, such as the antennas and relay.
3. Please go to a professional car shop or car factory to install the system.
Chapter TWO
INSTALLATION
2. 1 Accessories
1) Necessaries
(1) GSM mobile phone: 1-3 mobile phones (NoteMobile phone must have Caller ID and SMS functions.)
(2) A valid GSM SIM card (with Caller ID & SMS functions and enough balance) to be installed in the CAT
devices;
2) System Setup
1Main Unit
(2) Remote control: Maximum remote control: 3pcs, study code.
Alarm/door lock
Unalarm/ unlock your car, and cancel alarm
a) Press the key only: to alarm and lock your car, turn off siren
b) Press the key and the to cancel alarm and unlock your car.
turn off siren
c) In case of wrong call alarm, press the key to cancel it.
Press the key to activate your car lights so that you will be able to
search for your car.
(3.1) GSM antenna (3.2) GPS antenna (4) Vibration sensoradjustable Sensitivity
22 INSTALLATION
OFF ON
EMG: SOS Button VIS: Vibration Sensor STATE: LED Light J1: Wire Harness
5) Microphone installation
6) Connect SOS button wire to EMG port.
7) Connect Vibrator sensor wire to VIS port.
8) Connect the LED wire to STATE port.
9) Put the 20PIN Connector into J1 of the main unit, the WORK light starts flashing.
Then slide the battery switch toON.
10) Fix After installation, check all the wires conecting OK, and use dual glue band to bundle them well.
Last, fix the main unit well.
CHARPTER THREE
BASIC OPERATIONS
31 SMS Format
Formal SMS format *PASSWORD*COMMAND#. It is sent by mobile phone.
Note 1: You can use big or small alphabet in COMMAND. All SMS starts with *PASSWORD* and end with #.
Note 2: You can use any mobile phone to send SMS. But you have to input the right password.
Note 3: You can use the monitor center number (any four digit) to send SMS.
Note 4: PASSWORD must be 4-digit. The factory default is 1234.
You can use digit or English character to compose PASSWORD.
Note 5: The quotation marks will not show in your mobile phone.
Note 6: / will not show in your mobile phone.
1) Recipients Setup
Recipients are the mobile numbers which will be alerted via SMS when there is an alarm activated. You may
set up up to three recipients ( You must set Recipient A. You may set B or C recipient or both B and C recipients).
Use your mobile phone to send a SMS to the SIM card inserted in CAT device as below:
Set up recipient A:
Send the following SMS to the device Setup successful, the reply SMS reads
*PWD*AXXXXXXXXXX# ARMED/UnArmed: A:
XXXXXXXXXXB: C:
Send the following SMS to the device Setup successful, the reply SMS reads
*PWD*AXXXXXXXXXXX* ARMED/UnArmed: A:
BXXXXXXXXXXX# XXXXXXXXB:XXXXXX C:
Send the following SMS to the device Setup successful, the reply SMS reads
*PWD*AXXXXXXXXXXX* ARMED/UnArmed: A:
BXXXXXXXXXXX*CXXXX XXXXXXXXB:XXXXXX
XXXXXXX# C:XXXXXXXX
Change or Cancel recipientsPlease use the above operations to set up new recipients.
Note: A,B,C indicates the recipients A,B,CXXXXindicates the mobile phone number. Maximum digit: 20.
+is added when SMS format requires the country code. SMS Format: + Country Code + mobile phone number. For
example, Recipient A setup*PASSWORD *A+8613666504824+86 refers to China,13666504824 refers to Recipient
A mobile number
Recipient number shows blank if you do not set up it.
2) Set up Time-zone
Send the following SMS to the device Setup successful, the reply SMS reads
Send the following SMS to the device Setup successful, the reply SMS reads
Note: xxx Range: 200999. Minimum range:200 meter. Maximum range:999 meters.
Considering the error of GPS data, xxx Range shoud be over 300 meters
Switch off : If you do not input range meter, the CAT-4 will use the factory default.
Send the following SMS to the device Setup successful, the reply SMS reads
Note: xxx choose 020999express minimum speed is 20Km/Hr; maximum limited speed is 999 Km/H.
If xxx is less than 20CAT-4 will not send Overspeed Alert SMS to recipient
Switch off: If you dont want this alert reports, switch the function off.
Send the following SMS to the device Setup successful, the reply SMS reads
NoteFor the first time using , the CAT-4 will not alarm automatically. You have to press Unarmed key to activate the
automatic Alarm Setup function.
C. SMS Alarmed
Send the following SMS to the device Setup successful, cat reply
*PWD*S# Armed;Engine:on/off;Door:close/open;
LAC:XXXXX;CID:XXXXX;
Time:XX-XX-XX XX:XX:XX Speed:xxxkm/h
S/N:xxdxxmxxs W/E:xxxdxxmxxs
D. Set up Alarm Mode through Voice OperationsPlease refer to the voice operations
Note: 1.When you do not close the door or do not turn off the engine , you will not be able to press to set up Alarm.
2. When you do not close the door or do not turn off the engine , you will not be able to set up Alarm through SMS .
The reply SMS showsUnalarmed
3. If you set up Alarm through wrong voice operations, you will be repliedUnalarmed
4. You can set up Alarm successfully only when there are no blight in setting up Alarm.
5. In Alarm state, you will not be able to turn on engine.
Unarmed Setup
Press in the remote control to cancel Alarmed Mode. The siren sounds twice.
B. SMS Unalarmed
Send the following SMS to the device Setup successful, cat reply:
*PWD*C# Unarmed;Engine:off;Door:off;
Lac:XXXXX;CIDXXXXXX;
Time:XX-XX-XX XX:XX:XX Speed:xxxkm/h
S/N:xxdxxmxxs W/E:xxxdxxmxxs
Note1. In Unalarmed Mode, if door is open, the car rear lights flashes periodically.
2. If you fail to set up Unalarmed Mode through SMS, you will get reply SMSAlarmed
3. If you fail to set up Unalarmed Mode through voice operations, you will get reply Alarmed
4. You can set up Unalarmed Mode successfully only afer removing all blight.
Change PASSWORD
By SMSSend the following SMS to the device Setup successful, cat reply :
Switch Off:
Send the following SMS to the device Setup successful, the reply SMS reads
Switch On:
Send the following SMS to the device Setup successful, the reply SMS reads
Note: When you turn off the vibration alarm, if someone shake your car , the CAT-4 will not send Shake Alert to you. But the car light
will glint and the siren will ring.
Enforced De-energize You can send SMS to cut off engine in emergency status.
Enforced De-energize
Send the following SMS to the device Setup successful, the reply SMS reads
Re-ernergize
Send the following SMS to the device Setup successful, the reply SMS reads
A. By manual: Press in the remote control. Your car light will flash and the siren will ring over
5 seconds.
B. By SMS
Send the following SMS to the device
After sending the command, the CAT-4
*PWD*T#
will not send SMS to you. But the siren
will ring and your car lights will flash for 4
seconds.
Resume to Factory Default
By SMS
Send the following SMS to the device Setup successful, the reply SMS reads
Wrong Message
In case SMS command has not been executed , you will receive the following Format incorrect SMS.
(8) Restart functionAuto restart function in CAT. But there is some unwontedness you can press and hold
in the remote control for 20 seconds to restart the system.
313 Query
Recipients Query
Send the following SMS to the device Setup successful, the reply SMS reads
*PWD*Y# Armed(UnArmed);A:XXXXX
XB:XXXXXXXXXC:XXXXX
Version Query
Send the following SMS to the device Setup successful, the reply SMS reads
Note: xxxx refers to version date
*PWD*VER# NEWCAT4:xxxxx
By callFor recipient A onlyWhen theres no alarm, Recipient A may call the terminal and hang up within
four beeps. Then the terminal will send the status SMS to Recipient A
Send the following SMS to the device Setup successful, the reply SMS reads
Send the following SMS to the device Setup successful, the reply SMS reads
Send the following SMS to the device Setup successful, the reply SMS reads
*PWD*GPS# LAC:XXXXX;CID:XXXXX;
$GPRMCxxxxxxxx
NoteIf GPS positioning is successful after the CAT-4 receives the command, the CAT-4 will reply GPRMC data to you.. If GPS fails
to position, the CAT-4 will reply LAC and CID data to you.
32 Voice Operations
Dial the SIM number of CAT-4. After 4 rings, you will call through the CAT-4 device. Following the voice prompt
instructions, you will be able to query the present status of your vehicle and finish most of the settings and operations.
Note: You have to input correct PASSWORD. The PASSWORD is the same as in SMS operations
N
Sorry, password denied
Welcome to
Access accepted
Press 1 Press 3
New
Press 2 Please password
Please input your accepted
query about your Alarm control Modify your input your new
vehicle conditions new four-digit
password four-digit password
password again Sorry
Press1
Switch your CAT Armed Mode activated
into armed mode
Press2 Switch your CAT
into un-armed mode Unarmed Mode activated
Press3
De-energize and stop the engine The engine has been turned off
Press4
Re-energize and make the The engine could be started up now
engine available
Press5
Restore factory settings Factory settings restored
Press6
Monitor the voices in your vehicle
Press*
Return to the previous directory
CHARPTER FOUR
41 Alarm Functions
411 Alarm type
Shake Alert
Door open Aert
Engine-On Alert
Engine-Off Alert
Highjack Alert Aert (SOS)
Move-on Alert
Over speed Alert
Note: 1.All alarms will report to your mobile phone.
2. Emergency alarm (SOS) works only in Unalarmed Mode status. Other alarm functions work only in
Alarmed Mode.
Car responseThe GSM LED starts flashing to indicate alerts. The car light will be glint and the siren will
be ringing.
Phone call reportCAT-4 will automatically call the recipient A to report alarm status.
41 Alert Report
Shake Alerty: On Armed Mode, when the vehicle vibrates, there will be Shake Alert.
In Alarmed ModeCAT4 will send a Shake Alert SMS to recipient A at each vibration. At the same
time, the car lights will be glint and the siren will be ringing to scare the people who shake the vehicle.
Press key in the remote control. CAT-4 will send a Shake Alert SMS to recipient A at each
vibration. But the siren will not be ringing and the car lights will not be on.
Phone No
NoteVibration Alert will be able to continue. Shake Alert SMS is sent at every 30 seconds.
The sensitivity of the vibration sensor could be adjusted by the knob on it. Since Vibration Alert might be high frequency
In Emergency Alert the CAT will send a SOS SMS to recipient A,B and C. Then it will call automatically
to recipient A.
Door-open AlarmOn Armed Mode, if the door is open, there will be a Door-open Alarm.
In Door-open Alarm, the CAT-4 will send a Door Open Alert SMS to recipient A,B and C. Then it will
call automatically to recipient A. At the same time, the car lights will be on and the siren will be ringing for 5-6
seconds.
Door-open Recipient Recipient
Recipient A
Alert B C
Car Locale voice and lighe caution 56 sec
Door open Alert; LAC:XXXXXCID:XXXXX
SMS Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
S/N:xx.xxxx W/E:xxx.xxxx
Engine On Alarm: On Armed Mode, if the engine is turned on, there will be an Engine-On Alarm.
In Engine-On Alarm, the CAT-4 will send a Engine-on Alert SMS to recipient A,B and C. Then it will
call automatically to recipient A. At the same time, the car lights will be on and the siren will be ringing for 5-6
seconds.
Engine-on Recipient Recipient Recipient
Format
Alert A B C
Car Locale voice and lighe caution 56 sec
Engine on Alert; LAC:XXXXXCID:XXXXX
SMS Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
S/N:xx.xxxx W/E:xxx.xxxx
Phone Call Engine-on Alert
Power-off Alarm:
In Engine-Off Alarm, the CAT-4 will send a Circuit Cut-off Alert SMS to recipient A,B and C. Then it
will call automatically to recipient A. At the same time, the backup battery will supply power.
Car Locale No
Move-on Alarm
In Alarm Mode, when someone moves your vehicle 200 meters away manually or using other equipment,
the CAT-4 will send a Move Alert SMS to recipient A,B and C. Then it will call automatically to recipient A.
Car Locale No
Note1. Move Alert will be sent once in each Alarm Mode status.
You will have to set Alarm Mode again for next Move-on Alarm.
2. Sometimes GPS will show move in static situation. It is related to the GPS antenna place. In some heavily blocked
areas, the GPS move will reach 100 meters. So we set the Move-on Alarm range to be 300 meters.
Over speed Alert: In the process of drivingthe car speed is over limited speed, the CAT will send Alert SMS to
Recipient A
42 Alert Management
4.2.1 Cancel Alarm
Cancel AlarmPress in the remote control to cancel alarms.
4.2.2 Monitor Alarm
In Alert status, the CAT-4 will send alert SMS to recipients. Then it will call automatically to recipient A.
After alert, recipient A can press # to monitor car.
4.2.3 Ghost Hand
When the burglar drives your vehicle away, you can stop the vehicle by a single SMS.
WARNING: This command might be very dangerous to the DRIVER and the CAR when the car is MOVING! Please BE
CAUTIOUS to active this function!
A By SMS
You will be able to send *PWD*STOP# command to cut-off your engine. After this function is
activated, the car will stop or will not be engine-on again.
After alert , the car will not be able to be started again unless you have re-energized the vehicle by SMS.
You must send *PWD*K# command to restart your engine.
CHAPTER FIVE
1SMS FORMAT
Alert
Switch On / Off Alert Format REMARK
mode
Alarmed Shake Alert; LAC:XXXXXCID:XXXXX
SHAKE
ON: *PWD*H#Has done the turning on shake alert! Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h SMS to A
ALERT S/N:xx.xxxx W/E:xxx.xxxx
OFF: *PWD*N#Has done the turning off shake alert!
During driving Overspeed Alert; LAC:XXXXXCID:XXXXX
OVER
ON: *PWD*SPDXXX# SPDXXX SETUP OK! Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h SMS to A
SPEED
OFF: *PWD*SPD000#SPD000 SETUP OK! S/N:xx.xxxx W/E:xxx.xxxx
Door open Alert; LAC:XXXXXCID:XXXXX
DOOR SMS to:A.B.C
Alarmed Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
OPEN Phone call A
S/N:xx.xxxx W/E:xxx.xxxx
Engine on Alert; LAC:XXXXXCID:XXXXX
ENGINE SMS to:A.B.C
Alarmed Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
ON Phone call A
S/N:xx.xxxx W/E:xxx.xxxx
Circuit Cut-off Alert; LAC:XXXXXCID:XXXXX
POWER SMS to:A.B.C
Alarmed Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
OFF Phone call A
S/N:xx.xxxx W/E:xxx.xxxx
Alarmed Move Alert; LAC:XXXXXCID:XXXXX
MOVE SMS to:A.B.C
ON: *PWD*MOVEXXX# MOVEXXX SETUP OK! Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
ALERT Phone call A
OFF *PWD*MOVE000# MOVE000 SETUP OK! S/N:xx.xxxx W/E:xxx.xxxx
Highjack Alert; LAC:XXXXXCID:XXXXX
HIGHJACK SMS to:A.B.C
Alarmed/ Unarmed Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h
ALERT Phone call A
S/N:xx.xxxx W/E:xxx.xxxx
PC Operation System
Software
Software Initialization
Activate Software
Software Interface
GPRS Settings
Track Settings
5. Vehicle Management
Vehicle management interface
6. Electronic Map
Map settings
7. Command Functions
Data display
Vehicle status
8.Alarm Management
Alarm Info
Alarm management
9. Map Use
Show the location on the map
Playback manually
Auto playback
Center Number
Remote Control
2. Alarm Settings
Alarm Type
Alarm Settings
Route-Points Report
IMEI Number
GPRS Data
Chapter I
you can track, record and manage your vehicles. It is used for fleet vehicle management.
Individual user can also use the software. Please do not use the software in other car security
products. The software uses hook-on navigation map (Google Earth, for example) to display
vehicle position.
Main Features
1. Fleet ManagementA group of vehicle info may be input in the software. You will be
2. Map DisplayYou can use hook-on map (Google Earth, for example) to display your
vehicle.
3Vehicle StatusYou will be able to send command from the software center to check your
vehicle status.
4Real Time TrackingYou can send track command to the terminal through the software
center. The terminal will periodically report GPS data to the center.
5Alarm ManagementThe software center can receive all the alert messages and the GPS
data.
6. History Info PlaybackYou will be able to play back the history info and see the vehicle
7.GPRS DataThe software can receive, process GPRS data from the terminal.
8Export GPRS DataBy using the software, you can export GPRS data into Excel files to
save it.
2. Configuration Requirement
Hardware
b.R232 port GSM/GPRS ModemYou must use our GSM /GPRS modem.
Note: GSM GPRS Modem installation: Please refer to the GSM/GPRS MODEM
User Manual.
PC Operation System
System languageEnglishChinese
Minimum Configuration
Intel Pentium
128 MB
1GB
4 CD-ROM
56K
Software
Double click the setup.exe to install. Below are the installations.See Picture 1
ClickNext
ChooseI agree to the terms of this license agreement. Then click Next
Installing
Installation is done.
Picture 1
Software Initialization
2.Choose serial COM port and the baud rate. Choose GPRS or not.
Picture 2
b. PressOKto turn off the interface. Two prompts are displayedsee Picture 3.
Picture 3
dAfter the software initialization, choosestartall programs CAT.GPS
Activate Software
Install the GSM GPRS modem (Model: MOD9001, supplied by the manufacturer) on the PC
with the help of the RS232 port and wait till the green indicator on the modem starts to blink.
See Picture 4
Picture 4
The program will check the connection between the RS232 Modem and the PC. If there
shows a reminder as Picture 5. Then you will need to check whether the software COM port is the
same as the physical RS232 port provided by the PC. If not, then please try to modify the COM
Port setting the same as the PC RS232 setting here:
Configuration System Settings Other Settings COM Port
When the green indicator in the GSM modem is ON, you can be able to activate the software.
Picture 5
Picture 6
Software Interface
Picture 7
Modem connectionNormal
Cut off
Network
Normal
Checking Network
Picture 9
GPRS Settings
a. Configuration System Settings GPRS Settings
b. Configure the Center IP (Same as the static IP of the PC), Carrier (APN), COM
port and Dial-up number.
c. Set up time interval. Testing time ranges from 130 minutes. GPRS data will
automatically report to the center at the preset time interval. If no GPRS data
reports to the center, the center will automatically remind you of GPRS settings.
d. Press OK to confirm.
(See Picture 10)
Note: COM port 8090 is default setting for the software running. If this port is occupied,
you can choose other COM port. Otherwise, the GPRS function will not be able to work.
Picture 10
Procure IP address You may procure it through Router or log in the following
website: http://vbnet.mvps.org/resources/tools/getpublicip.shtml
the GPRS data from WAN, you can use network connectivity to WAN.
c. ChooseForwarding
IP as LAN IP address. Set up the COM port for your software use.
e. PressSAVE.
Track Settings
a. Configuration System Settings Track Settings
b. Configure the Time Interval and the Total Report Times.
up.See Picture 11
Moving
Picture 11
Total Report Times can be set at No Limit or Limited. In Limited selection, you can
Limited
Picture 12
Picture 13
System Password
a. Configuration System Settings System Password
b. Configure the Password (Software Password)
c. Default: 1234
d. Max length: 6
See Picture 14
Picture 14
5.Vehicle Management
Vehicle management interface
Picture 15
b. Saving
c. Successful
Picture 16
NoteIf you fail to add a new vehicle into the software, you will see the prompt below
(Picture 17). Please check your SIM card number and the Modem connection.
Picture 17
vehicle information.
Picture 18
6. Electronic Map
Map settings
a. Configuration Map Settings
b. Click to browse the exe file of the navigation map (Google Earth)
(See Picture 20)
Note: You can not choose desktop icon of the exe file.
a. Map setting
c. PressOK
d. Successful
Picture 20
You can activate the map by clicking Navigation Map or by using the software.
b. If it shows the error info as MAP format error!, then please check whether the map
Picture 21
7. COMMAND Functions
Data Display
After you have configured the vehicle info, the related data will be showed in Vehicle Status
& History Info.
See Picture 22
Vehicle Status
History Info
Picture 22
Vehicle Status
In the Vehicle Status, right-click on one vehicle and you will be able to send different
commands to it(See Picture 23).
Picture 23
GPS
No GPS
Picture 24
Track StartedClick Track Started to start periodical report.
Track CancelledClick Track Cancelled to cancel periodical report.
Activate GPRSClick Activate GPRS to make the terminal report by GPRS.
In GPRS function, GPS data is sent through GPRS network. But COMMAND settings are
sent by GSM network. You will need to use GPRS server to activate GPRS function.See
Picture 25
GPRS OFF
GPRS ON
Picture 25
Picture 26
8.Alarm Management
Alarm Info: After you have connected the terminal to the center, all the alarms except the
vibration alarm will be sent to the center. When the software has received the alarm info, there will
be an alarm reminder. You will also be able to check the alarm info by clicking .
Picture 27
a. Click Warning
b. Alarm Info
Picture 27
In the Alarm Info window, you will be able to check all the alarm info.
a. Select More Info, you will be able to view more detailed alarm info.
b. Select All Alarms, you will be able to view all the alarm info including the histories.
(If you dont select All Alarms, only the alarms that havent been managed will be
displayed.)
(See Picture 27)
Alarm ManagementWhen a new alarm is coming, it displays No. After the received
alarm has been managed, you may click on Manage. Then it displays Yes. Then the related
alarm will be listed in the histories.
9. Map Use
Show the Location on the Map
After you have activated the related map software successfully, you will be able to view
the location on the map illustratively by double-clicking on one GPS data you get. Please see
Picture 28 for an example of Google Earth.
See Picture 28
Picture 28
a. GoogleEarthfree.exe
b. MyGE5.zipIt is Google Earth Navigation KeypadIf you have the file available, you will
to install MyGE5.
Activate MyGE5.zip and Google EarthPlease refer to Activate Map operation. You can
execute MyGE5.exe to activate Google Earth. After MyGE5.exe execution, GoogleEarth and
Picture 29
Picture 30
North up and South down. The red arrow up sign indicates the vehicle move direction.
The red arrow up sign indicates vehicle head direction. The black arrow indicates the
C.2Dor3D
Press the icon to display the vehicles position. You will not be able to move the Map.
Release the icon to move the Map. It does not display the vehicles position.
Press the icon to record tracking. The tracking file format: The present timeaccuracy:
track file. Then the vehicle move route will display in Google Earth.
FMap positioningDouble click .It displays . You will be able to see the vehicle
position in the MapSee Picture 31.If you do not want to position your vehicle, you can click
to turn ON/OFF.NoteTo enlarge or dwindle the Map, you will be able to press .
In non-positioning status, you can use your mouse to enlarge or dwindle the Map.
Picture 31
10.Other Functions
History Info
In History Info, all the history data of each vehicle will be recorded.See Picture 32
Picture 32
Click More Info to check details list.
See Picture 33
Picture 33
Playback Manually
a. Select Playback Manually.
b. Double-click on one data, you will see a window named Location Query Platform.
c. You will be able to playback all the history data with the help of the Location Query
Platform.
See Picture 34
Picture 34
Auto Playback
a. Right click on the vehicle name Track Settings
See Picture 35
Picture 35
b. Adjust the playback speedSlow<>Express
c. Select the playback periodStart time<>End of time
See Picture 36
Picture 36
GPS data will be repeatedly recorded into the Base Station Management. According to the related
Base Station data , you will be able to fill in the related address. Then you will still be able to
See Picture 37
b. Select a GPS data from the GPS data pool. Click . Then you will be able to fill in
to save it.
The GSM Base Station address will appear in Base Station Management.
The GSM Base Station address will appear in the Vehicle Info.
Picture 37
Picture 38
c. Select the related parameters and click OK, then the data will be exported into ExcelSee
Picture 39.
No record display
Picture 39
c. Configure the related parameters according to your needs and click ClearSee Picture 41.
Picture 41
Database Backup
a. Data Backup Database
b. All the data including all the histories will be copied and stored in the Backup folder in the
installation place.See Picture 42
a. backup sucessful
b. backup file
Picture 42
Resume Backup
a. Data Resume Backup
b. Select the related backup file and the present software database will be replaced as the
Command*Password*GXXXX#
Command*Password*G#
Command*Password*DXXXX#
Command*Password*D#
Command*Password*YY#
Note: Three recipients (A,B,C), the monitor center number and the address translation
aVehicle Status
Command*Password*X#
Reply#08#Cut-off/Alertforcibly/Armed/UnArmed;Engine:on/off;Door:close/open;
LAC:XXXXX;CID:XXXXX;$GPRMCxxxxxxxx#
Note: You can use the command to check your vehicle status, such as door and engine
status.
ReplySETUP OK!
Note: First two XX stands for the time interval counted by 20 seconds. It will be with no
limit when its 00. In this case, the CAT-4 will not send the GPS information to the monitoring
center
The next two XX stands for the report times. The report times range from 1-99. This
function will be deactivated when its 00. In this case, CAT-4 will send the GPS information to the
monitoring center continuously.
Example:
#08#Cut-off/Alertforcibly/Armed/UnArmed;Engine:on/off;Door:close/open;
LAC:XXXXX;CID:XXXXX;$GPRMCxxxxxxxx#
If the distance is set at less than 300 metersthere will not be the distance base periodical
report function.
Remote Control
Command*Password*STOP#
NoteWhen you use this function, you will be able to change the vehicle alarm status to be
Unalarmed.
c.Alarm Setup
Command*Password*I#
Command*Password*C#
2. Alarm Settings
Alarm Type
NoteThere are eight alarm types followed by GPS data. $GPRMCxxxxxxxxx is followed
the alert messages if GPS function is available. The Base Station and LAC(local area
exchange center) are followed the alert messages if GPS function is not available.
Alarm Format
Engine:onoff;Door:onoff;LAC:XXXXXCID:XXXXX;$GPRMCxxxxxxxx#
06:GEO alert
Alarm Settings
Command*Password*SCXXXX.XX*XXXXX.XX*XXXXX#
ReplySETUP OK!
Example
*1234*SC4149.20*12323.52*08000#
NoteThe minimum radius is 300 meters. There is no GEO alert if you set the radius
less than 300meters.
Command*Password* SPDXXX#
ReplySETUP OK!
Route-Points Report
With this command, you can set 10 different points. When the vehicle gets close to each
point, CAT-4 will report to the Monitoring Center. This function can only be activated when there
is a Monitoring Center. The setup details will be similar to GEO Fence setups.
Command:
*Password*SDXXXX.XX*XXXXX.XX*XXXXX,XXXX.XX*XXXXX.XX*XXXXX#
ReplyCurrent num is xx
If you want to send data of several different points (maximum point: 6) in one SMS, you can
input , after the first string of the data of the first point. Then you can just input the related data
of the second point. The rest may be deduced by analogy.
Example:
*1234*SD4143.58*12325.58*00500,4144.29*12326.40*00500,4145.58*12325.51*
00500,4146.03*12325.28*00500#
Command*Password*CLEAR#
Command*Password*FUN01#
ReplyFunction open!
Command*Password*FUN00#
ReplyFunction close!
If all are available, it will connect to the IP through TCP protocol. CAT4 will automatically
connection is cut off, it will re-connect to the IP. When you use SMS command to set up
GPRS or you have changed the IP and the COM port, the GPRS connection will be cut off
GPRS Settings
Command*Password*IP:XXX.XXX.XXX.XXX:XXXXXAPN:XXXXX#
ReplyIP:XXX.XXX.XXX.XXX:XXXXXAPN:XXXXX#
Command*Password*IP#
ReplyIP:XXX.XXX.XXX.XXX:XXXXXAPN:XXXXX#
Command*Password*HEARTx#
IMEI Number
Command*Password*IMEI#
ReplyIMEI:XXXXXXXX-
GPRS Data
Example#08#Cut-off/Alertforcibly/Armed/UnArmed;Engine:on/off;
Door:close/open;LAC:XXXXX;CID:XXXXX;$GPRMCxxxxxxxx#xxxxxxxxxx-#
NoteLast group of number xxxx indicates the GSM Module IMEI number.
bGPRS Alarm
161229.487,A,3723.2475,N,12158.3416,W,0.13,309.62,120598,,*10#135025417862103-#
0106:Alarm Type
06:GEO alert