Professional Documents
Culture Documents
Carpenter PDF
Carpenter PDF
Carpenter PDF
Trade: Carpenter
1. Which one of the following saw is having a reinforcement strip (rib) on its back?
A. Hand saw B. Tenon saw C. Coping saw D. Feat saw
6. Which board is made up of country wood strips of various sizes ranging from 18-38mm in thickness?
8. Which one of the portable machine tool is very competent for cutting wood, composition board,
Veneer, Plastics, chard board, Leather?
10. The caliper meant for measuring the width of a slot is----.
A. Firm joint caliper B. Jenny caliper C. Lap joint caliper D. Spring joint caliper
A. It is cheap and easily available. B. It can be shaped easily into different form a designs.
C. It can be repaired and reused. D. The cost of work man ship is more than other materials.
15. The length of the tenon blind mortise and tenon joint is -------.
A. 1/2 with of the mortise piece. B. 2/3rd with of the mortise piece.
C. 3/4th with of the mortise piece. D. 4/5th with of the mortise piece.
16. In which direction the in feed roll moves the stock for planning in thickness planer?
17. What the name of the chisel used for cutting rough surface quickly for turning on wood turning lath?
C. It is lighter in weight. D. It can be easily worked and bent in shaped and designs
23. Which one of the sawing operation is not related to circular saw machine?
24. Which of the tool used for testing the straightness of large surface?
25. In which sander the shaft moves up and down through the slotted table?
26. Which one of the following saw can hold three various size of blade for different uses?
27. Which seasoning the timber is stacked inside the chamber and the hot air is forced to remove, the
moisture content?
A. Double cut file. B. Single cut file. C. Raps file. D. Triangular file.
A. 35 B. 45 C. 50 D. 50
41 Abnormal growth on the side of the caused by injury or irritation of the trunk is due to the defect?
42 This part of the wood surrounds the true wood which is softer and lighter in color?
43 A trunk of tree with branches cut off and bark removed is-------------------.
45 A think plank having a thickness of 20mmto50mm and the width 180mm or less is -----------------.
A. Scantling B. Batten. C. Strips. D. Plank.
46 Which plane is very much use for planning the wood quickly and truly?
47 Which screw driver mostly used by the carpenter for fixing and removing the wood screws?
A. Upper wheel. B. Thrust wheel. C. Lower wheel. D. Spring loaded tilting wheel.
53 The standard height of the band saw table above the table is --------------------.
57 It is a combination of steps leading from one floor to the other floor of a building-----------------.
A. Corner half lap joint. B. Dovetail half lap joint. C. Tee half lap joint. D. Cross half lap joint.
59 It is a thin internal wall which is constructed the inside the closed building to divide the space in to
rooms and areas is -----------------.
A. Bridle joint. B. Mortise and tenon joint. C. Housing joint. D. Bevel scarf joint.
A. Height 28, Deep 10, Width 8 to 32. B. Height 30, Deep 8 to 10, Width 6 to 28.
C. Height 30, Deep 12, Width 9 to 48. D. Height 28, Deep 12, Width 9 to 48.
Q. 63. What are the standard sizes of tall cabinets manufactured?
A. Height 66, Width 24 to 26, Deep 26. B. Height 66, Width 27 to 30, Deep 24.
C Height 64, Width 22 to 24, Deep 20. D. Height 60, Width 24, Deep 22.
Q. 64. What is the standard size of vanity cabinet?
A. Height 31 , Width 24 to 36, Deep 21. B. Height 17 , Width 22, to 24, Deep 20
C. Height 28, Width 28, Deep 20. D. Height 31, Width 22, Deep 20.
A. Height 28, Width 20, Deep 22. B. Height 34 , Width 9 to24, Deep 24.
C. Height 30, Width 28, Deep 22. D. Height 28, Width 28, Deep 18.
Q. 66. What is the height of the counter top is usual above the floor?
A. 30, 36, 42. B. 20, 24, 36. C. 18, 20, 24. D. 24, 36, 42.
A. Mortise and tenon joint. B. Bridle joint. C. Tongue and groove joint. D. Half lap joint.
A. Hoop iron. B. Single faced pallets. C. Double faced pallets. D. Boy pallets.
A. Tongued and grooved joint. B. Housing joint. C. Dovetail joint. D. Lengthening joint.
Q. 83. What is the name of special rule used by the pattern maker to prepare the pattern?
A. Collapsible rule. B. Wooden foot rule. C. Zig zag rule. D. Shrink rule.
Q. 85. Which tool is provided on pattern to avoid sharp corners at the junction of two adjacent surfaces?
(Angle)
Q. 86. What is the main purpose of providing the fillet on the pattern?
A. The size of pattern is different than size B. The size of pattern is slightly less in dimension
Casting. than the casting
C. The pattern is equal dimensions of casting. D. The size of pattern is slightly larger in
dimension that the casting.
Q. 89. What is the core print?
Q. 90. Where the two types of description of object are can be read?
Q. 93. What is the use of providing dowel pin in pattern and core box?
A. Slit the pattern, core box and keep alignment. B. Joint the pattern.
Q. 97. Which core print is used when horizontal core does not extend entirely the casting and the
A. Balanced core print. B. Vertical core print. C. Horizontal core box. D. Hanging core print.
Q. 98. Which core box has two halves which are clamped together for producing a core?
A. Slab core box. B. Split core box. C. Half core box. D. Gang core box.
Q. 99. What is the draft allowance on external surface of a pattern for general casting?
A. 1 to 5 mm/meter. B. 5 to 10 mm/meter.
C. 10 to 15 mm/meter. D. 15 to 20 mm/meter.
A. Lighter in weight, Strong and durable. B. It is has straight grain and uniform in colure.