Professional Documents
Culture Documents
501 206 PDF
501 206 PDF
Supported System Types Table 3: Voltages Greater Than 277 Vac L-N/480 Vac L-L Wiring Diagrams Figure 7: 3-Phase 3-Wire 3 CT no PT Figure 8: 3-Phase 4-Wire Wye Direct
Three-Phase Wiring Voltage Input Connection 3 CT
Table 2: Voltages Less Than or Equal to 277 Vac L-N/480 Vac L-L, Direct Connect No PTs Figure 3: 1-Phase Line-to-Neutral 2-Wire Figure 4: 1-Phase Line-to-Line 2-Wire
CTs Voltage Connections Meter Configuration System 1 CT System 1 CT L1 L2 L3 N L1 L2 L3
CTs Voltage Connections Meter Configuration Number of Figure
Number of Wires System PT Primary Number
System PT Primary Figure Number Qty. ID Qty. ID Type N L1 L1 L2
Wires Qty. ID Qty. ID Type Type Scale
Type Scale
V1, V2, V3, (Vn Grounded Based on
Single-Phase Wiring* 3 I1, I2, I3 3 40 13 3 V1 3 V1
to Ground) Wye voltage 4 V2 4 V2
1 I1 2 V1, Vn L-N 10 No PT 3 V1, V3 (Vn to Based on 3 V 1 3 V1 5 V3 5 V3
2 3 I1, I2, I3 2 Wye 42 14 4 V 2 4 V2 6 6
1 I1 2 V1, V2 L-L 11 No PT 4 Ground) voltage VL-L <= 480V VN VN
5 V 3 5 V3
3 2 I1, I2 3 V1, V2, Vn L-L with N 12 No PT 5 4 V1, V2, V3 (Vn Grounded Based on 6
2 I1, I2, I3 3 40 15 V N 6 VN S1 S1
to Ground) Wye voltage 14 I1+ 14 I1+
* Single-phase systems must be connected only as shown in wiring diagrams. Otherwise, meter will not display values. 15 I1 15 I1
S1 S1
Three-Phase Wiring Grounded 14 I1+ 14 I1+
S2 S1
16 I2+
S2 S1
16 I2+
V1, V2, V3 (Vn Based on
1 I1 3 Wye 44 16 15 I1 15 I1 17 I2 17 I2
2 I1, I3 3 V1, V2, V3 Delta 30 No PT 6 to Ground) voltage S2 S2
(Balanced) 16 I2+ 16 I2+ S2 S1
18 I3+
S2 S1
18 I3+
3 I1, I2, I3 3 V1, V2, V3 Delta 31 No PT 7 17 I2 17 I2 19 I3 I3
3 19
18 I3+ 18 I3+ S2 S2
1 I1 3 V1, V2, V3 Delta 32 No PT 19 I3
19 19 I3
(Balanced) The following symbols are used in the wiring diagrams:
3 I1, I2, I3 3 V1, V2, V3, Vn 4-wire 40 No PT Use System type 31. Use System type 40.
8 Use System type 10. Use System type 11. Use with 480Y/277 V and 208Y/120 V systems.
Delta Table 4: Wiring Diagram Symbols To avoid distortion, use parallel wires for control To avoid distortion, use parallel wires for control
4 3 I1, I2, I3 3 V1, V2, V3, Vn Wye 40 No PT 8 power and voltage inputs. Keep the fuse close power and voltage inputs. Keep the fuse close
Symbol Description Figure 9: 3-Phase 3-Wire Delta Connection Figure 10: 3-Phase 3-Wire Delta
1 I1 3 V1, V2, V3, Vn Wye 44 No PT to the power source. to the power source.
20 Voltage disconnect switch
2 CT 2 PT Connection 3CT 2PT
(Balanced) Use with 120/240 V systems.
L1 L2 L3 L1 L2 L3
Fuse Figure 5: 1-Phase Direct Voltage Figure 6: 3-Phase 3-Wire 2 CT no PT
Table 3: Voltages Greater Than 277 Vac L-N/480 Vac L-L Connection 2 CT
Three-Phase Wiring Earth ground
N L1 L2 L1 L2 L3
3 V1 3 V1
CTs Voltage Connections Meter Configuration 4 V2 4 V2
Number of Figure 5 5
System PT Primary V3 V3
Wires Qty. ID Qty. ID Type Number Current transformer. 6 6
Type Scale S1 (X1) VN VN
Polarity marks: S1=X1, S2=X2. V1
3 3 V1
V1, V3 (V2 to Based on 4 V2 S1 S1
2 I1, I3 2 Delta 30 9 S2 (X2) 4 V2 14 I1+ 14 I1+
Ground) voltage 5 V3 5
Shorting block V3 15 I1 15 I1
V1, V3 (V2 to Based on 6 VN 6 VN S2 S2 S1
3 3 I1, I2, I3 2 Delta 31 10 16 I2+ 16 I2+
Ground) voltage 17 I2 17 I2
S1 S1 S2 S1
S1
V1, V3 (V2 to Delta Based on 14 I1+ 14 I1+ 18 I3+ 18 I3+
1 I1 2 32 18 15 I1 15 I1 19 I3 19 I3
Ground (Balanced) voltage S2 S2 S2 S2
Potential transformer. S1 16 I2+ 16 I2+
V1, V2, V3, (Vn Wye Based on 17 I2 17
3 I1, I2, I3 3 40 11 Polarity marks: = X1. S1
I2
to Ground) (Unbalanced) voltage 18 I3+ 18 I3+
S2 For an open delta PT connection with 120 V L-L
V1, V2, V3, (Vn Wye Based on Protection containing a voltage disconnect switch with a fuse or 19 I3 19 I3 Use System type 31.
3 2 I1, I3 3 40 12 secondaries, use System type 30.
to Ground) (Unbalanced) voltage disconnect circuit breaker (the protection device must be rated for
S2 For an open delta PT connection with 120 V L-L
the available short-circuit current at the connection point). secondaries, use System type 31.
V1, V2, V3, (Vn Wye Based on
1 I1 3 44 17 Use System type 12. Use System type 30.
to Ground) (Unbalanced) voltage
In 2 PT systems, these connections are equivalent. To avoid distortion, use parallel wires for control
L1 V1 L1 V1 Polarity marks: = X1 power and voltage inputs. Keep the fuse close
V2 V2 to the power source.
L2 L2
L3 V3 L3 V3
Figure 11: 3-Phase 3-Wire Wye Connection Figure 12: 3-Phase 3-Wire Wye Connection Figure 15: 3-Phase 4-Wire Wye 2 CT 3 PT Figure 16: 3-Phase 4-Wire Wye 1 CT 3PT Figure 19: 3-Phase 3-Wire Direct Voltage Figure 20: 3-Phase 4-Wire Direct Voltage
3 CT 3 PT (unbalanced) 2CT 3PT (unbalanced) (for balanced 3-wire loads) (balanced) Input Connection 1 CT Input Connection 1 CT Figure 23: Direct Connect Control Power Figure 24: Control Power Transformer
(balanced) (balanced) (DC Control Power) (CPT) Connection
L1 L2 L3 L1 L2 L3 N L1 L2 L3 N L1 L2 L3
L1 L2 L3 N L1 L2 L3 N L1 L2 L3
3 V1 3 V1
3 V1 3 V1
4 V2 4 V2 4 V2 4 V2
5 V3 5 V3 5 V3 5 V3 3 V1 3 V1 1 2
6 VN 6 VN 6 VN 6 VN 4 V2 4 V2 1 2 - +
- +
5 V3 5 V3
S1 S1 S1 S1 6 VN 6 VN
14 I1+ 14 I1+ 14 I1+ 14 I1+
15 I1 15 I1 15 I1 15 I1
S2 S1 S2 S2 S2 S1 S1
16 I2+ 16 I2+ 16 I2+ 16 I2+ 14 I1+ 14 I1+
17 I2 17 I2 17 I2 17 I2 15 I1 15 I1
S2 S1 S1 S1 S2 S2
18 I3+ 18 I3+ 18 I3+ 18 I3+ 16 I2+ 16 I2+
19 I3 19 I3 19 I3 19 I3 17 I2 I2 DC Control Power 100 Vdc < V < 300 Vdc Control Power Transformer
17
S2 S2 S2
18 I3+ 18 I3+ See Table 5. 120 or 240 Vac Secondary 50 Va max.
19 I3 19 I3 See Table 5.
Use System type 40. Use System type 40. Use System type 44
Use System type 40.
Use System type 32 Use System type 44
Figure 13: 3-Phase 4-Wire Wye Connection Figure 14: 3-Phase 4-Wire Wye 3CT 2PT Figure 17: 3-Phase 3-Wire Wye 1CT 3PT Figure 18: 3-Phase 3-Wire 1 CT 2 PT
3 CT 3 PT (balanced) Figure 21: Direct Connect Control Power Figure 22: Direct Connect Control Power Table 5: Fuse Recommendation
(unbalanced) (balanced)
(Phase to Phase) (Phase to Neutral)
N L1 L2 L3 N L1 L2 L3
Control Power Source Source Voltage (Vs) Fuse Fuse Amperage
L1 L2 L3 L1 L2 L3
L1 L2 L3 N L1 L2 L3 CPT Vs 125 V FNM or MDL 250 mA
CPT 125 < Vs 240 V FNQ or FNQ-R 250 mA
V1
CPT 240 < Vs 305 V FNQ or FNQ-R 250 mA
3 3 V1
3 V1 3 V1
4 V2 4 V2 Line Voltage Vs 240 V FNQ-R 250 mA
4 V2 4 V2
5 V3 5 V3
Line Voltage Vs > 240 V FNQ-R 250 mA
5 V3 5 V3 1 2
6 VN 6 VN 1 2
6 VN 6 VN - + -+ DC Vs 300 V LP-CC 500 mA
S1
I1+ S1 NOTES:
14 14 I1+ S1 S1
14 I1+ 14 I1+ See Figure 21 to Figure 24.
15 I1 15 I1
S2 S1 S2 S1 15 I1 15 I1 Over current protection should be located as close to the device as possible.
16 I2+ 16 I2+ S2 S2
16 I2+ 16 I2+
17 I2 17 I2 For selecting fuses and circuit breakers other than those listed above, use the following criteria:
17 I2 17 I2
S2 S1 18 I3+ S2 S1
18 I3+ Over current protection should be rated as listed above.
18 I3+ 18 I3+
19 I3 19 I3
19 I3 19 I3
Current interrupt capacity should be selected based on the installation category and fault current capability.
S2 S2
Phase to Phase only when voltage Phase to Neutral only when voltage Over current protection should be selected with a time delay.
< 415 + 10% Vac max. < 300 + 10% Vac max. The voltage rating should be based on the input voltage applied.
See Table 5. See Table 5. If a 0.25 A fuse is not available with the required fault current capability, use a fuse rated at a maximum of
Use System type 40. Use System type 42. Use System type 44 Use System type 32 0.5 A.
COMMUNICATIONS CAPABILITIES Figure 26: Parts of PM710 Display Figure 27: PM710 Abbreviated IEC Menu Hierarchy* Setup Example: This example shows how to set up CTs. Use the same method to set up PTs and
Communication.
A. Type of measurement A B C D
Table 6: RS485 Communications Distances
B. Screen Title 1. Press ###: until you see SETUP.
Maximum Communication Distances I PHASE DMD PEAK
1 to 32 Devices C. Alarm icon 2. Press SETUP.
Baud Rate
D. Maintenance icon 3. Enter your password. The default #42!4)/
Feet Meters
E. Bar Chart (%) ) -!8$%-!.$ password is 00000.
9600 8,000 2,438 ZZZZZ\\\\\\ E U-V U V
F. Units
4. Press OK.
19200 6,000 1,829 !
G. Display more menu items F 5. Press METER.
NOTE: Distances listed should be used as a guide only and cannot be guaranteed for non-
POWERLOGIC devices. Refer to the master devices documentation for any additional distance
H. Menu item
M
ZZZZZ\\\\\\
!
PQS PQS PHASE DMD
6. Press CT. #4 02)-
limitations. I.
J.
Selected menu indicator
Button ZZZZZ\\\\\\
!
7. Enter the PRIM CT (primary CT) number:
1 to 32762. #4 3%#
E Ph Qh Sh 8. Press OK.
!
K. Return to previous menu L
Daisy-chaining Devices to the Power Meter L. Values . 9. Enter the SEC. CT (secondary CT)
number: 1 or 5. /+
The RS485 slave port allows the power meter to be connected in a daisy chain with up to 31, 2-wire M. Phase 0(!3% $-$
PF 10. Press OK.
devices. In this document, communications link refers to a chain of devices that are connected by a
communications cable. G 11. Press 1; to return to the SETUP MODE
screen.
F
Figure 25: Daisy-chaining 2-wire devices K J I H
L- (D 0 ) ^ Indicates the menu item is selected and there are no menu levels below the current level.
RESET
7 8
7 8
7 8
7 8
Change values or scroll through the available options. When the end of a range is reached,
Power Meter or other POWERLOGIC 2-wire compatible devices + pressing + again returns to the first value or option.
SETUP METER DMD PASSW COM BARG
Belden 9841 wire colors: blue with white stripe (+), white with blue stripe (), and silver (shield) <- Select the next number of a series.
OK Move to the next editable field or exits the screen if the last editable field is selected.
If the power meter is the first device on the daisy chain, connect it to the host device using a RS232 to
DIAGN. METER
RS422/RS485 converter.
If the power meter is the last device on the daisy chain, terminate it with the terminator provided.
See Table 6 for the maximum daisy-chain communications distances for 2-wire devices.
The terminals voltage and current ratings are compliant with the requirements of the EIA RS485 Set Up the Power Meter U = Voltage, L-L
communications standard. Figure 27 shows abbreviated hierarchical relationships of the menu screens for the PM710. Using the V = Voltage, L-N
Schneider Electric This product must be installed, connected, and used in compliance with prevailing
Connection number 10 is not used. Setup Example below in conjunction with the menu hierarchy (Figure 27), complete a minimum setup of standards and/or installation regulations. As standards, specifications, and designs
Power Monitoring and Control
the power meter. A minimum setup includes: change from time to time, please ask for confirmation of the information given in
*The power meter can be configured to display either IEC or IEEE nomenclature. Figure 27 shows IEC
295 Tech Park Drive, Suite 100
OPERATING THE DISPLAY Set up CTs. nomenclature.
LaVergne, TN 37086
this publication.