Professional Documents
Culture Documents
Cargo Handling Gear
Cargo Handling Gear
4-1. INTRODUCTION. Cargo-handling gear is used to secure cargo while it is being raised or lowered by the
ship's gear. It also moves cargo to and from its stowage position in the ship. Proper training in the selection and
use of cargo-handling gear is necessary for safe and efficient cargo operations. As terminal operations
coordinator, you are responsible for training and supervising your personnel in the methods prescribed by this
chapter.
4-2. GENERAL-PURPOSE GEAR. General-purpose gear is used with many types of cargo. This type of gear
includes-
Endless slings.
Single slings.
Combination slings.
Chain slings.
Canvas slings.
The ends of slings are usually made up into eyes, either with or without thimbles (Figure 4-1). The eyes fit on the
cargo hook and attach to the drafts or loads of cargo. By these eyes, a sling is joined to another sling, a hook, or a
ring, either directly or by using a shackle. Thimbles in the eyes strengthen the sling by protecting it from sharp
bends around pins, hooks, shackles, links, rings, and similar objects.
a. Endless Slings. Splicing the ends of a piece of wire or fiber rope makes an endless sling. It is simple to handle
and can be used in several different ways to lift loads. The endless sling is most commonly used as a choker
hitch. When the endless sling is used as a choker, personnel pass it around the draft or cargo forming a loop on
top of the draft. The other end is passed through this loop, pulled tight and attached to the cargo hook. To balance
the load, personnel spread apart the two parts of the sling on the bottom of the draft.
(1) The endless sling is also used with chime or running hooks. It may be used as a basket sling or a vertical sling
(Figure 4-2).
(2) Personnel should not use endless slings to lift bagged cargo such as sugar, flour, and cement. These types of
items require canvas slings.
Figure 4-2. Types of endless slings
b. Single Slings. A single sling is made of fiber or wire rope. Each end of the single sling is made up with an eye,
a hook, a ring, or a thimble, depending on the intended use of the sling. A single sling may be used as a vertical
sling, a basket sling, or a choker sling with a choker hitch (Figure 4-3). Single slings made of fiber rope are used
for light loads and for cargo that might be damaged by wire slings. Slings made of wire rope have a variety of
uses. They are made in lengths ranging from 5 to 150 feet or longer for special cargo. Running hook wire rope
slings may be used to hoist drafts of lumber, dunnage, iron pipe, building steel, strong boxes, and large cases
(Figure 4-4). Each running hook sling is made with 18-inch eyes at each end. Personnel use the sling by wrapping
it around the draft, attaching one eye to the sliding hook, and putting the other eye on the cargo hook.
e. Canvas Slings. A canvas sling is a rope sling with a section of canvas sewn between the ropes (Figure 4-8).
The main type of canvas sling in use is the dirt sling. In commercial practice, canvas slings similar to dirt slings
are used for handling cargo such as nitrate.
4-3. SPECIAL-PURPOSE GEAR. Special-purpose gear is made for use with certain types of cargo. It includes-
Cargo nets.
Pie plates.
Pallets.
Bridles.
Plate-handling clamps.
a. Cargo Nets. Cargo nets are usually made of manila rope, but nets of wire rope are used for special cargoes.
The standard Army cargo net is 14 by 14 feet with a 7 7/8-inch square mesh. The square meshes are made of 2
1/2-inch circumference manila rope. The line around the circumference of the net is made of 3-inch circumference
manila rope. Cargo nets are used to handle loose packages that are not all the same size. The package must be
strong enough to withstand pressure. When making up a draft in a cargo net, cargo handlers should stack the
cargo so that the crushing effect of the net is kept to a minimum.
c. Pallets. The four basic types of pallets used in military cargo handling are the stevedore, general-purpose,
sled, and warehouse pallets.
(3) The sled pallet is a heavy timbered platform with runners (Figure 4-12). Supplies and equipment are normally
banded to the pallet.
Figure 4-11. General-purpose
pallet
(4) A warehouse pallet is used to handle cargo in warehouses. It is much lighter than the stevedore pallet. The
most common size of warehouse pallet is 48 by 48 inches, but a 40- by 48-inch size is also made. The warehouse
pallet can be the open end type that is moved by a forklift or hoisted by a pallet bridle, or the closed end type that
is moved by forklift only.
(5) When items of cargo are palletized, the tiers are laid so that one tier ties together with another to give stability
to the unitized load and to keep the cargo from falling off the pallet while it is being moved. Cargo handlers can
obtain greater use of the pallet area by building the load in a definite pattern whenever possible.
(a) Wheel nets are used for hoisting sedans and other light vehicles
(refer to Figure 4-13). The wheel nets included in the cargo set vehicle are 8 by 3 feet, with 6-inch mesh. Manila
rope that is 3 inches in circumference is used in the net with the exception of the frame which uses 3 3/4-inch
manila rope.
(b) When using the sling and wheel net, the winch operator lowers the cargo hook until the wheel nets are on the
ground. The nets are spread out in this position so there is enough clearance between the top of the cargo net
and the bottom of the vehicle spreader to allow the vehicle to enter.
(c) The vehicle is pushed until its wheels are in the net. Cargo handlers may also use other types of slings to load
vehicles. For example, a four-legged bridle can be used if the vehicle has been fitted with lifting eyes.
(2) Heavy-lift spreaders are made of steel beams because stronger material is required to keep greater pressure
away from the side of the heavy lift (Figure 4-14).
(3) Barrel sling spreaders may be triangular, straight, or square (Figure 4-15). They are usually made of plate
steel with holes for the shackles which hold the chime hooks. Cargo handlers may hoist a number of drums at one
time with the use of the barrel sling spreader.
(4) Pallet bridle spreaders keep pressure away from the sides of the draft (Figure 4-16). The straight types are
made of steel or hardwood.
e. Bridles. Bridles are lifting devices designed to hoist special types of cargo. They may be used in conjunction
with spreaders. A list of the most common types of bridles follows.
(1) Pallet bridles are used for quick, efficient handling of palletized cargo (Figure 4-17). Cargo handlers should
insert the lifting bars at the bottom of the nets into the ends of the pallet to use the bridle. Then they should
spread the sling nets around the cargo as far as they will reach and slip the eyes over the cargo hook. The bars at
the top serve as spreaders.
Figure 4-17. Pallet bridle
(2) Beam bridles are used to remove hatch beams from their sockets (Figure 4-18). Cargo handlers should place
the hooks on opposite sides of the beam in the lightening holes or rings as provided. The beam will then ride level
and straight up and down. Tag lines are attached to the bridles for control and safety.
(3) Vehicle bridles are used for efficient handling of various types of vehicles. The size of the bridle depends on
the size of the vehicle to be hoisted. Cargo handlers should use vehicle spreaders with wheel nets for passenger
vehicles. Heavy-lift spreaders are used for trucks.
(4) Heavy-duty bridles are used to reduce side pressure on heavy lifts. Bridles use a combination of wire rope,
shackles, hooks, rings, or chain. Cargo handlers should know the safe working load of this type of gear when
using these bridles. Table 4-1 gives the recommended minimum size of shackles, chain, hooks, and rings to be
used with various sizes of wire rope.
(1) The single lever grip clamp is used for lifting plates in a horizontal position. It has a tapered jaw opening, a
toothed clamping arm, and an oval ring. It picks up the plate resting in a horizontal plane and keeps it horizontal
while it is being lifted.
(2) The double-toothed cam grip clamp is chain operated with a sling link for lifting steel plates in a vertical
position. It can lift only one plate at a time. It picks up the plate resting in a horizontal plane and turns the plate
over until it hangs vertically.
4-4. CARGO-HANDLING AIDS. Cargo-handling aids are used to help handle cargo. These include items such as
wedge point bars (pinchbars), rollers, and tag lines.
a. Wedge Point Bars. Wedge point bars have a wedge-shaped working end for prying. They are used to shift
heavy cases into position over short distances with a grease-like substance called skid compound. For longer
distances, cargo handlers use the wedge point bar to pry the case up high enough to get rollers under it (Figure 4-
20).
b. Rollers. Personnel use rollers to move cargo from the wings and ends of a hatch to the square of the hatch.
There are several types of rollers usually available.
(1) Pallet-type truck dollies or pallet dollies consist of a steel frame and eight bar rollers. Cargo handlers may land
pallets of cargo on truck dollies in the square of the hatch. The dollies are then pulled into the wings where the
cargo is to be stowed. Cargo handlers can place empty pallets on the dollies in the wings. When loaded with
cargo, the dollies are pulled into the square of the hatch to be placed in position for hoisting the cargo.
(2) Single rollers are round bars of wood, steel, or steel pipe. The rollers included in the general hatch cargo set
are made of hardwood and are 3 3/4 inches in diameter and 4 feet long. Single rollers are used to move heavy
cargo in a hold.
(3) Gravity conveyors are normally made in 10-foot sections. They may be either wheel or roller type. Cargo
handlers may set up roller conveyors in the hold to move small boxes or other suitable items of cargo from the
square of the hatch into or out of the wings.
c. Tag Lines. Tag lines are long lengths of light line made fast to long items of cargo and heavy lifts for the
purpose of controlling the swing of the draft as it is being hoisted or lowered.
4-5. CARE OF CARGO-HANDLING GEAR. The following simple rules will help prolong the life of cargo-handling
gear. Cargo handlers should-
Apply a light coat of oil to the wire rope slings periodically. A lubricated sling will wear five times longer than a dry
sling.
Clean cargo-handling gear regularly.
Ensure manila rope slings are dry before storing to prevent mildew.
Keep gear not in use in the gearbox or locker to prevent damage.
Know the safe working load of all gear (TM 5-725).
Not exceed the safe working load of any part of the rigging or of the cargo-handling gear at any time.
Never overload a sling and never apply loads suddenly