Professional Documents
Culture Documents
Air Filter 894509 - 03 - A - 02 - DA400
Air Filter 894509 - 03 - A - 02 - DA400
DA 400
Compressed-Air Filter System
December 2016
DA 400 compressed-air filter system
Sealing air For optimum supply of sealing air to the The DA 400 consists of three filter stages
The sealed linear and angle encoders encoders, the required air flow is 7 L/min (prefilter, fine filter and activated carbon
from HEIDENHAIN can be operated with to 10 L/min per linear encoder or 1 L/min filter) and a pressure regulator with pressure
sealing air to increase the level of protection. to 4 L/min per angle encoder. Ideally the gauge. The pressure gauge and the pressure
This offers additional defense against air flow is regulated by the HEIDENHAIN switch (which is available as an accessory)
contamination. The compressed air, acting connecting pieces with integrated throttle effectively monitor the sealing air.
as sealing air, introduced directly into the (see Accessories). At an inlet pressure of
encoders must be cleaned by a microfilter approx. 1 105 Pa (1 bar), the throttles The compressed air introduced into the
and must comply with at least the following ensure the prescribed volume of airflow. DA 400 must fulfill the requirements of the
purity classes as per DIN/ISO 8573-1 (2010 following purity classes as per ISO 8573-1
edition): DA 400 (2010 edition):
HEIDENHAIN offers the DA 400
Solid contaminants: Class 1 compressed-air filter system for purifying Solid contaminants: Class 5
Particle size No. of particles the compressed air. It is designed Particle size No. of particles
per m3 specifically for the introduction of per m3
0.1 m to 0.5 m 20 000 compressed air into encoders. 0.1 m to 0.5 m Not specified
0.5 m to 1.0 m 400 0.5 m to 1.0 m Not specified
1.0 m to 5.0 m 10 The DA 400 has special filters which 1.0 m to 5.0 m 100 000
Max. pressure dew point: Class 4 ensure that the quality of the filtered air Max. pressure dew point: Class 6
(pressure dew point at 3 C) remains constant even at low airflows. (pressure dew point at 10 C)
Total oil content: Class 1 It is extremely tolerant towards sudden Total oil content: Class 4
(max. oil concentration: 0.01 mg/m3) changes in pressure in the air supply, such (max. oil concentration: 5 mg/m3)
as can be caused by other consumers in
the machine being switched on or off.
Specifications DA 400
Operating temperature 5 C to 30 C
3
Flow rate Max. 360 L/min ( 21.6 Nm /h)
Mass 1 kg
5
10 Pa 1 bar
Operating pressure
4 bars to 12 bars
Condensation runoff
5.6
*) Space required for filter replacement
6.8
d 0.5 m
d3m
d 0.5 m
d 50 m
d 0.5 m
d 50 m
d9m
d1m
d9m
d1m
1)
Swiveling screw fitting 90, M5 ID 207834-02
With seal
1)
Swiveling screw fitting 180, M5 ID 630380-01
With seal
for LS 4x7/LC 4x5
1)
Spacer ID 230905-01
T-joint ID 310094-02
Quick disconnect 6 x 1
Filter elements
Prefilter VF-DA 400 ID 810415-01
Fine filter FF-DA 400 ID 810416-01
Activated carbon AK-DA 400 ID 810421-01
1)
An additional connecting piece is necessary.
Further information
Brochure: Linear Encoders for
Numerically Controlled Machine Tools
DR. JOHANNES HEIDENHAIN GmbH
Dr.-Johannes-Heidenhain-Strae 5 Brochure: Angle Encoders with
83301 Traunreut, Germany Integral Bearing
{ +49 8669 31-0
| +49 8669 32-5061
E-mail: info@heidenhain.de
www.heidenhain.de