Professional Documents
Culture Documents
M1
M1
MECHANICS OF DEFORMABLE
BODIES
Kristine May Maturan, CE
Cor Jesu College, Inc.
AY 2016 -2017 1
MODULE 1
TENSION, COMPRESSION, AND SHEAR
AY 2016 -2017 2
NORMAL STRESS
= (unit less)
AY 2016 -2017 5
SOLUTION
AY 2016 -2017 6
FIG. Tensile-test machine with automatic
data-processing system. (Courtesy of MTS
Systems Corporation) AY 2016 -2017 7
FIG. Rock sample being tested in
compression to obtain
compressive strength, elastic
modulus and Poissons ratio
(Courtesy of MTS Systems
Corporation)
AY 2016 -2017 8
STRESS-STRAIN DIAGRAMS
AY 2016 -2017 9
STRESS-STRAIN DIAGRAMS
AY 2016 -2017 10
STRESS-STRAIN DIAGRAMS
PROPORTIONAL LIMIT (HOOKE'S LAW)
where:
k = E (Youngs Modulus of Elasticity)
Thus, E
ELASTIC LIMIT
It is the limit beyond which the material will no
longer go back to its original shape when the
load is removed, or it is the maximum stress
that may be developed such that there is no
permanent or residual deformation when the
load is entirely removed.
AY 2016 -2017 11
STRESS-STRAIN DIAGRAMS
AY 2016 -2017 13
HOOKES LAW AND
POISSONS RATIO
o The linear relationship
between stress and strain for a
bar in simple tension or
compression is expressed by
the equation
= Hookes Law
Where:
= axial (normal) stress
E = constant of proportionality
known as modulus of
elasticity (often called as
Youngs modulus)
= axial strain
AY 2016 -2017 14
HOOKES LAW AND
POISSONS RATIO
AY 2016 -2017 15
HOOKES LAW AND
POISSONS RATIO
o The lateral strain at any point
in a bar is proportional to the
axial strain at that same point if
the material is linearly elastic.
o The ratio of these strains is a
property of the material known
as Poissons ratio, (read as nu).
= =
Axial elongation and lateral contraction of a
prismatic bar in tension: (a) bar before
loading, and (b) bar after loading. (The The minus sign is inserted in the
deformations of the bar are highly equation to compensate for the fact
exaggerated.) that the lateral and axial strains
normally have opposite signs.
AY 2016 -2017 16
SAMPLE PROBLEM 2
o A steel pipe of length L = 4.0 ft, outside diameter d2 = 6.0 in., and
inside diameter d1 = 4.5 in. is compressed by an axial force P = 140 k.
The material has modulus of elasticity E = 30,000 ksi and Poissons
ratio = 0.30. Determine the following quantities for the pipe:
(a) the shortening ,
(b) the lateral strain ,
(c) the increase d2 in the outer diameter and the increase d1 in the
inner diameter, and
(d) the increase t in the wall thickness.
AY 2016 -2017 17
SOLUTION
AY 2016 -2017 18
SAMPLE PROBLEM
AY 2016 -2017 19
SHEAR STRESSES
AY 2016 -2017 20
SHEAR STRESSES
1. Single Shear
There is only one (1) plane of shear and the shear force is equal to
the total load transmitted.
2. Double Shear
There two (2) planes of shear and the shear forces is equal to one-
half of the total load transmitted.
3. Bearing Stress
Is developed when two separate bodies press against each other.
The bearing area is defined as the projected area of the bearing
surface.
AY 2016 -2017 21
SHEAR STRESSES
AY 2016 -2017 23
NORMAL STRESS
P
A
AY 2016 -2017 24
SHEARING STRESS
P
A
P
2A
AY 2016 -2017 25
BEARING STRESS
Pb
b
Ab
AY 2016 -2017 26
SAMPLE PROBLEM 3
A punch for making holes in steel plates is shown in the figure. Assume
that a punch having diameter d = 20 mm is used to punch a hole in an 8-
mm plate, as shown in the cross-sectional view. If a force P = 110 kN is
required to create the hole, what is the average shear stress in the plate
and the average compressive stress in the punch?
AY 2016 -2017 27
A steel strut S serving as a brace for a boat hoist
transmits a compressive force P = 12 k to the deck
of a pier (Fig. a). The strut has a hollow square
SAMPLE PROBLEM 4
cross section with wall thickness t = 0.375 in. (Fig.
b), and the angle between the strut and the
horizontal is 40. A pin through the strut transmits
the compressive force from the strut to two
gussets G that are welded to the base plate B. Four
anchor bolts fasten the base plate to the deck. The
diameter of the pin is dpin = 0.75 in., the thickness
of the gussets is tG = 0.625 in., the thickness of the
base plate is tB = 0.375 in., and the diameter of the
anchor bolts is dbolt = 0.50 in.
Determine the following stresses: (a) the bearing
stress between the strut, S and the pin, (b) the
shear stress in the pin, (c) the bearing stress
between the pin and the gussets, (d) the bearing
stress between the anchor bolts and the base
plate, and (e) the shear stress in the anchor bolts.
(Disregard any friction between the base plate and
the deck.)
AY 2016 -2017 28
I. SIMPLE STRAIN ||WORKING
STRESS, ALLOWABLE STRESS, AND
FACTOR OF SAFETY
o Working stress is defined as the actual stress of a material under a
given loading. The maximum safe stress that a material can carry is
termed as the allowable stress.
o The allowable stress should be limited to values not exceeding the
proportional limit. However, since proportional limit is difficult to
determine accurately, the allowable tress is taken as either the yield
point or ultimate strength divided by a factor of safety.
o The ratio of this strength (ultimate or yield strength) to allowable
strength is called the factor of safety.
AY 2016 -2017 29