Professional Documents
Culture Documents
Catálogo de Sellos Grizzli
Catálogo de Sellos Grizzli
Catálogo de Sellos Grizzli
Reference Guide
Single Parts
Hydraulic Seal Specialists
Page # Page #
A5 Snap in Wiper 22
Additional Profiles 67
Single Step
Metric Rod/Piston
A6 Snap in Wiper 28 Seals
MUS Symmetrical 70
A8 Snap in Wiper 29 U Cup
DK Snap in Wiper 32
MPS Piston Seal (2 78
Pc)
MSW Snap in Wiper 33
OK Step Cut Piston 81
Seal (2 Pc)
MPW Pin Wiper 34
MCPS Capped 83
Additional Profiles 37 Piston Seal (4 Pc)
Page # Page #
Sakagami
ZS Z Seal 225
Sakagami Profiles 110
Metric O-rings
MOR Metric O-ring 114 UR Unloaded Rod 228
Seal
Page # Page #
Page #
Caterpillar 429
Replacement Parts 2
Pc Slipper Seal
Caterpillar 431
Replacement Parts
4 Pc Capped Piston
Seal
Caterpillar 432
Replacement Parts
Chem Cast - Inch
Caterpillar 434
Replacement Parts
Chem Cast - Metric
Caterpillar 435
Replacement Parts
Wear Ring
Caterpillar 443
Replacement Parts
Oval Ring
GRIZZLY SUPPLIES
MACHINED SEALS AND GASKETS
7
Credit Application
8
Credit Application
Credit Terms
Grizzly Supplies (2012) Ltd. Credit terms are as follows:
a) Terms are NET 30 from the date of the invoice.
b) All accounts over 60 days on COD basis only
c) $25.00 charge for all returned payments
d) Past due invoices are subject to a service charge of 2% per month
e) Any legal or collection costs incurred by Grizzly Supplies Ltd in and
about the collection of the account when overdue shall be borne by the
customer.
f) Grizzly Supplies (2012) Ltd. Reserves the right to revoke or limit credit
at any time.
I/We understand & agree to the credit terms stated above and I (we) authorize Grizzly Supplies (2012) Ltd
to obtain such credit and / or personal information as may be considered necessary. I am the applicant
named herin or an authorized representative of the company named herein and I certify that the above
information is true and complete and is furnished with the intent that it be relied upon by Grizzly
Supplies (2012) Ltd. In extending credit to the applicant. No information which might effect Grizzly Supplies
(2012) Ltds decision to extend credit has been withheld.
9
Parts Order Sheet
Fax: 1-855-505-0140
Hydraulic Seal Specialists
Date _______________
Customer: _________________________
Quote Only:
Approved: WO#: __________
Rod: __________ Bore: __________ Ship Via: __________
10
Parts Order Sheet
Fax: 1-855-505-0140
Hydraulic Seal Specialists
Date _______________
Customer: _________________________
Quote Only:
Approved: WO#: __________
Rod: __________ Bore: __________ Ship Via: __________
11
Reference Guide
Wipers
1 2 3 4 5 6 7 8
9 10 11 12 Metric
13 14 15 16
Wipers
Rod Seals
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28
12
Reference Guide
Piston Seals
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28 29 30
Wear Rings
1 2 3 4 5 6 7 8
13
Metric
Wipers
Metric
Metric
Wipers
Wipers
New parts are always being added. Call for sizes not shown and seal kits.
14
Metric
Wipers
MCW Metal Cased Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
A1 Snap in Wiper Double Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
A5 Snap in Wiper Single Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
A6 Snap in Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
A8 Snap in Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
MSWH Snap in Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DK Snap in Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
MSW Snap in Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MPW Pin Wiper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Additional Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
15
Metric
Wipers
OD
Prefix ID OD Height
Metric
Housing grooves are nominal sizes
Wipers
OD tol. is H8 Height
Height tol. is +0.5mm -0.0mm
ID
OD
Designed to press-fit into open groove housings. Comprised
of a polyurethane wiping element bonded to a metal
case. Capable of operating in dirty conditions and hostile
environments.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
16
Metric
Wipers
17
Metric
Wipers
MCW-120X130X7-NBR MCW-230X255X12
MCW-120X136X9 MCW-240X260X10
MCW-125X135X7-NBR MCW-240X260X12-NBR
MCW-125X140X9-NBR MCW-240X265X12
MCW-125X140X9 MCW-250X275X12
MCW-125X141X9 MCW-260X285X12
MCW-130X145X9 MCW-280X310X16
MCW-130X146X9 MCW-300X330X16
MCW-135X145X7-NBR
MCW-135X150X9-NBR
MCW-140X150X7-NBR
MCW-140X155X9-NBR
MCW-140X160X10
MCW-145X160X9-NBR
MCW-145X165X10
MCW-150X165X9-NBR
MCW-150X170X10
MCW-160X175X9-NBR
MCW-160X180X10
MCW-170X185X10-NBR
MCW-170X190X10
MCW-175X190X10
MCW-180X195X10-NBR
MCW-180X200X10
MCW-180X205X12
MCW-190X205X9
MCW-190X215X12
MCW-200X216X8
MCW-200X220X12-NBR
MCW-200X225X12
MCW-210X230X12-NBR
MCW-210X235X12
MCW-220X240X12-NBR
MCW-220X245X12
New parts are always being added. Call for sizes not shown and seal kits.
18
Metric
Wipers
Molded in urethane this light to medium duty wiper features a double-stepped shoulder to fit tightly in the
gland throat.
Provides complete protection against impurities such as dust, fluid, or other elements of contamination
that may reach the sealing system through the rod, which could damage internal components of the
cylinder.
Easily installed, this type of wiper is appropriate for applications exposed to particularly dusty and humid
environments.
A1-4X12X4/7 1 1 A1-23X31X4/7 1 1
A1-5X8X2.2/4 1 0.5 A1-25X33X4/7 1 1
A1-6X10X2.2/4 1 0.5 A1-26X34X4/7 1 1
A1-8X14X2.6/5 1 1 A1-28X36X4/7 1 1
A1-8X16X4/7 1 1 A1-28X38X4/7 1 1
A1-10X16X2.6/5 1 1 A1-30X38X4/7 1 1
A1-10X18X4/7 1 1 A1-32X40X4/7 1 1
A1-12X18X2.6/5 1 1 A1-33X41X4/7 1 1
A1-12X20X4/7 1 1 A1-34X42X4/7 1 1
A1-14X20X3.1/5 1 1 A1-35X43X4/7 1 1
A1-14X22X4/7 1 1 A1-36X44X4/7 1 1
A1-15X23X4/7 1 1 A1-38X46X4/7 1 1
A1-16X24X4/7 1 1 A1-40X48X4/7 1 1
A1-17X25X4/7 1 1 A1-41X49X4/7 1 1
A1-18X24X3.1/5 1 1 A1-42X50X4/7 1 1
A1-18X26X4/7 1 1 A1-44X52X4/7 1 1
A1-20X28X4/7 1 1 A1-45X53X4/7 1 1
A1-22X30X4/7 1 1 A1-45X57X5.5/10 1 1
19
Metric
Wipers
A1-46X54X4/7 1 1 A1-93X101X4/7 1 1
A1-47X55X4/7 1 1 A1-95X103X4/7 1 1
A1-48X56X4/7 1 1 A1-97X105X4/7 1 1
A1-50X58X4/7 1 1 A1-100X108X4/7 1 1
A1-50X58X4/7-H 1 1 A1-102X114X5.5/10 1 1
A1-51X59X4/7 1 1 A1-105X117X5.5/10 1.5 1.5
A1-52X60X4/7 1 1 A1-106X118X5/10 1.5 1.5
A1-53X61X4/7 1 1 A1-106X118X5.5/10 1.5 1.5
A1-54X62X4/7 1 1 A1-110X118X4/7 1 1
A1-55X63X4/7 1 1 A1-110X122X5.5/10 1.5 1.5
A1-56X64X4/7 1 1 A1-112X124X5.5/10 1.5 1.5
A1-57X65X4/7 1 1 A1-113X121X4/7 1 1
A1-58X66X4/7 1 1 A1-114X122X4/7 1.5 1.5
A1-60X68X4/7 1 1 A1-115X127X5.5/10 1.5 1.5
A1-62X70X4/7 1 1 A1-117X129X5.5/10 1.5 1.5
A1-63X71X4/7 1 1 A1-118X130X5.5/10 1.5 1.5
A1-64X72X4/7 1 1 A1-120X132X5.5/10 1.5 1.5
A1-65X73X4/7 1 1 A1-125X137X5.5/10 1.5 1.5
A1-66X74X4/7 1 1 A1-128X140X5.5/10 1.5 1.5
A1-67X75X4/7 1 1 A1-130X142X5.5/10 1.5 1.5
A1-68X76X4/7 1 1 A1-131X139X4/7 1.5 1.5
A1-70X78X4/7 1 1 A1-135X147X5.5/10 1.5 1.5
A1-72X80X4/7 1 1 A1-140X152X5.5/10 1.5 1.5
A1-73X81X4/7 1 1 A1-140X152X5.5/11 1.5 1.5
A1-75X83X4/7 1 1 A1-142X154X5.5/10 1.5 1.5
A1-78X86X4/7 1 1 A1-145X157X5.5/10 1.5 1.5
A1-80X88X4/7 1 1 A1-149X157X4/7 1 1
A1-82X90X4/7 1 1 A1-150X162X5.5/10 1.5 1.5
A1-83X91X4/7 1 1 A1-152X164X5.5/10 1.5 1.5
A1-85X93X4/7 1 1 A1-154X166X5.5/10 1.5 1.5
A1-86X94X4/7 1 1 A1-155X167X5.5/10 1.5 1.5
A1-88X96X4/7 1 1 A1-160X172X5.5/10 1.5 1.5
A1-90X98X4/7 1 1 A1-165X177X5.5/10 1.5 1.5
A1-92X100X4/7 1 1 A1-166X178X5.5/10 1.5 1.5
New parts are always being added. Call for sizes not shown and seal kits.
20
Metric
Wipers
21
Metric
Wipers
Prefix ID OD Height
New parts are always being added. Call for sizes not shown and seal kits.
22
Metric
Wipers
23
Metric
Wipers
24
Metric
Wipers
25
Metric
Wipers
26
Metric
Wipers
27
Metric
Wipers
A6 Snap in Wiper
Temperature: -50 to 230 F (-46 to 110 C)
Max. Surface Speed: 0.5 m/s
Prefix ID OD Height
Metric
Wipers
This wiper is designed to prevent foreign particles from being introduced into the internal components of
the hydraulic system.The profile has been specially designed for harsh environments, particularly in the
mining industry.
A special feature is the flap on the wiping lip which covers the gland housing, preventing the
water/slurry trap so common with conventional wipers and thus ingress of contamination around the
outside of the wiper.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
28
Metric
Wipers
A8 Snap in Wiper
L2
Temperature -22 to 221 F (-30 to 105 C)
Max. Speed: 1.0 m/s Total L1
Height L
Grizzly Supplies Part Numbers:
A8 - 16 X 24 X 4/8
Base
Height
OD D1 D2 ID
This wiper is designed to prevent foreign particles from being introduced into the internal components of
the hydraulic system. The lip is designed so that it reliably wipes dirt but leaves a residual film of oil on the
rod.
Part Number
Part Number D11
D D22
D L
L L11
L L22
L Part Number
Part Number D11
D D22
D L
L L11
L L22
L
29
Metric
Wipers
MSWH-11.2X19.2X4.5 MSWH-38X46X5/7 6 42 2
MSWH-16X22X3.6/4.8 4 18.5 MSWH-40X48X5/6.5 6 44 2
MSWH-16X24X4.5/6 5 20.3 2 MSWH-40X50X5/6.5
MSWH-18X24X4/7 MSWH-45X55X5/6.5 6 49 2
MSWH-18X26X4.5/6 5 22.3 2 MSWH-50X58X5/6.5 6 54 2
MSWH-20X26X4 4 22.5 2 MSWH-50X58X6.3/9-DA24
MSWH-20X28X4.5/6 5 24.3 2 MSWH-50X58.6X5.3-DA22
MSWH-20X28.6X5/7 6 2 MSWH-50X60X5/6.5 6 55 2
MSWH-22X30X4.5/6 5 26.3 2 MSWH-55X63X5/6.5 6 60 2
MSWH-25X33X4.5/6 5 29.3 2 MSWH-56X64X5/6.5 6 60 2
MSWH-25X35X6/8 7 30 3 MSWH-56X66X6/9.7 7 61 3
MSWH-25.4X33.4X5/6 6 37.7 2 MSWH-60X68X5/6.5 6 64 2
MSWH-28X36X4.5/6 5 32.3 2 MSWH-60X68.8X6.3/9-DA24
MSWH-30X38X5/6.5 6 34 2 MSWH-65X73X5/6.5 6 69 2
MSWH-32X40X5/6.5 6 36 2 MSWH-70X80X6/8 7 75 3
MSWH-35X43X5/6.5 6 39 2 MSWH-75X85X6/8 7 80 3
MSWH-36X44X5/6.5 6 40 2 MSWH-80X90X6/8 7 85 3
MSWH-36X44X5/8 MSWH-80X93X7 8 3
New parts are always being added. Call for sizes not shown and seal kits.
30
Metric
Wipers
MSWH-85X95X6/8 7 90 3 MSWH-200X225X13-AY
MSWH-85X97.2X8.1/12-DA24 MSWH-210X223X7/9.5 8 217 3
MSWH-90X100X6/8 7 95 3 MSWH-220X233X7/9.5 8 227 3
MSWH-95X105X6/8 7 100 3 MSWH-220X245X13-AY
MSWH-95X107.5X8/12 DA24 MSWH-230X243X7/9.5 8 237 3
MSWH-98X108X6/8 7 103 3 MSWH-230X255X12-AY
MSWH-100X110X6/8 7 105 3 MSWH-240X256X7/9.5 8 247 3
MSWH-105X115X6/8 7 110 3 MSWH-240X266X14-AY
MSWH-110X120X6/8 7 115 3 MSWH-250X265X9/11.5 10 258 3
MSWH-110X120X8 MSWH-260X275X9/11.5
MSWH-110X122.2X8.1-DA24 MSWH-260X286X18-AY
MSWH-110X130X10/13-AY MSWH-270X285X9/11.5
MSWH-112X122X6/8 7 117 3 MSWH-290X316X18-AY
MSWH-115X125X6/8 7 120 3 MSWH-300X315X9/11.5
MSWH-118X128X6/8 7 123 3
MSWH-120X130X6/8 7 125 3
MSWH-125X138X7/9.5 8 132 3
MSWH-125X145X10/13-AY
MSWH-130X143X7/9.5 8 137 3
MSWH-135X148X7/9.5 8 142 3
MSWH-140X153X7/9.5 8 147 3
MSWH-145X158X7/9.5 8 152 3
MSWH-150X163X7/9.5 8 157 3
MSWH-155X168X7/9.5 8 162 3
MSWH-160X173X7/9.5 8 167 3
MSWH-160X185X12
MSWH-165X178X7/9.5 8 172 3
MSWH-170X183X7/9.5 8 177 3
MSWH-175X188X7/9.5 8 182 3
MSWH-180X193X7/9.5 8 187 3
MSWH-190X203X7/9.5 8 197 3
MSWH-190X215X13-AY
MSWH-200X213X7/9.5 8 207 3
MSWH-200X216X9.5-DA24
31
Metric
Wipers
DK Snap in Wiper
Temperature: -20 to 210 F (-30 to 100 C)
Max. Speed: 2.0 m/s (395 ft/min)
Metric
Type DK is a single acting wiper seal of polyurethane for assembly into closed housings.
Wipers
Designed for light duty hydraulic applications.
Part Number
DK-12X18X1.3
DK-30X37.5X1.6
DK-33X40.5X1.6
DK-40X47.5X1.6
DK-45X52.5X1.6
DK-50X60X2.15
DK-55X65X2.15
DK-60X70X2.15
DK-63X73X2.15
DK-78X92X3.15
DK-80X90X2.15
DK-100X110X2.15
DK-140X150X2.15
DK-190X205X3.15
New parts are always being added. Call for sizes not shown and seal kits.
32
Metric
Wipers
A snap in wiper molded in urethane. This wiper has a lip on the outer diameter of the wiper to help
prevent contamination from entering the hydraulic system.
Part Number
MSW-50X60X6
MSW-70X83X7
MSW-75X88X7
MSW-80X93X7
MSW-85X98X7
MSW-90X103X7
MSW-95X108X7
MSW-100X110X6
MSW-100X113X7
MSW-105X118X7
MSW-110X123X7
MSW-120X133X7
MSW-220X240X10/18
33
Metric
Wipers
Primarily used as a pin wiper. Designed to press-fit into open groove housings. Comprised of a
polyurethane wiping element bonded to a metal case. Capable of operating in dirty conditions and hostile
environments.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
34
Metric
Wipers
35
Metric
Wipers
36
Metric
Wipers
Additional Profiles
842
FORSHEDA
EXCLUDER
PPUA
SG
37
Metric
Wipers
Metric
Metric Wipers
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
38
Metric
Wipers
39
Metric
Rod Seals
Prefix ID OD Height
Rod = 80mm
Groove size = 95mm
Seal Height = 10mm
Seal Groove Height = 10mm x 1.1 = 11mm
New parts are always being added. Call for sizes not shown and seal kits.
40
Metric
Rod Seals
MLR-30X40X7.3-EX MLR-100X120X14.5-EX
MLR-35X50X9.5-EX MLR-105X120X11.8-EX
MLR-36X46X7.3-EX MLR-110X125X14.5-EX
MLR-40X50X7.3-EX MLR-110X130X13-EX
MLR-40X50X10-EX MLR-110X130X14.5-EX
MLR-45X55X7.3-EX MLR-115X135X14.6-EX
MLR-45X60X11.4-EX MLR-120X135X14.5-EX
MLR-50X60X7.3-EX MLR-120X140X13-EX
MLR-50X65X10-EX MLR-120X140X14.6-EX
MLR-50X65X11.4-EX MLR-125X145X14.5-EX
MLR-55X70X11.4-EX MLR-130X145X14.5-EX
MLR-56X71X11.4-EX MLR-130X150X14.6-EX
MLR-60X72X9-EX MLR-140X160X13-EX
MLR-60X73X13-EX MLR-140X160X14.5-EX
MLR-60X75X11.4-EX MLR-150X170X14.6-EX
MLR-63X75X8.7-EX MLR-160X180X14.5-EX
MLR-63X78X11.4-EX MLR-160X185X14.5-EX
MLR-63X83X11.8-EX MLR-170X190X14.5-EX
MLR-65X75X10-EX MLR-180X200X14.5-EX
MLR-65X80X10-EX MLR-200X220X14.5-EX
MLR-65X80X11.4-EX MLR-200X230X22.7-EX
MLR-70X83X13-EX MLR-215X235X14.6-EX
MLR-70X85X11.4-EX MLR-230X249.3X14.5-EX
MLR-75X88X13-EX MLR-230X250X14.5-EX
MLR-75X90X13-EX MLR-230X260X22.5-EX
MLR-80X95X11.4-EX MLR-240X260X14.5-EX
MLR-80X95X13-EX MLR-250X270X14.5-EX
MLR-80X95X14.5-EX MLR-250X280X24-EX
MLR-85X100X11.8-EX MLR-255X275X14.5-EX
MLR-85X100X13-EX MLR-260X280X16.4-EX
MLR-90X105X11.4-EX MLR-280X310X22.5-EX
MLR-90X105X13-EX MLR-295X315X16.4-EX
MLR-95X110X13-EX MLR-305X325X16.4-EX
MLR-100X115X13-EX MLR-350X375X18-EX
41
Metric
Rod Seals
Rod application
Rod =80mm
Groove size =95mm
Seal Height =10mm
Seal Groove Height =10mm x 1.1=11mm
Piston application
Bore =95mm
Groove size =80mm
Seal Height =10mm
Seal Groove Height =10mm x 1.1=11mm
A standard B-lip profile loaded U cup utilizing a urethane shell energised by a high specification resilient
O-ring. At zero or low pressure, the O-ring helps to increase the sealing force preventing any bypass.
As pressure rises the sealing force increases and the O-ring provides complete lip actuation under most
conditions. The precision trimmed sealing lips ensure optimum sealing action. It can be used for single
acting applications or fitted back to back for double acting applications (while removing one O-ring loader
to prevent pressure trap).
New parts are always being added. Call for sizes not shown and seal kits.
42
Metric
Rod Seals
43
Metric
Rod Seals
44
Metric
Rod Seals
MLS-270X300X19
MLS-280X310X16
MLS-280X310X19
MLS-290X320X18
MLS-300X330X19
45
Metric
Rod Seals
Prefix ID OD Height
Molded in urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube
retention, and some contaminant resistance. Made for light to medium duty applications.
Most unloaded rod seals are double lip. Some items are single lip.
NRS rod shim with seal increases pressure capability. -R Rubber Max Pressure: 800 PSI
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
46
Metric
Rod Seals
47
Metric
Rod Seals
48
Metric
Rod Seals
49
Metric
Rod Seals
50
Metric
Rod Seals
51
Metric
Rod Seals
52
Metric
Rod Seals
MRU-220X240X14.5-S
MRU-220X240X15
MRU-220X245X15
MRU-220X245X15-NOK
MRU-220X250X18
MRU-220X250X22.7
MRU-230X260X19-NOK
MRU-240X260X14.5
MRU-250X280X19-NOK
MRU-250X280X22.7
MRU-260X290X18
MRU-260X290X19
MRU-260X290X19-NOK
MRU-265X290X16
MRU-280X310X18
MRU-280X310X22.7
MRU-290X215X18.5
MRU-290X320X22.5
MRU-300X330X19-NOK
MRU-360X380X14.5
MRU-360X385X20
MRU-360X390X22.5
53
Metric
Rod Seals
Prefix ID OD Height
Vee rings manufactured from fabric reinforced nitrile rubber. Vee pack sets are multiple-lip (chevron) seals, usually composed of
a male and female adaptor and a group of three to five vee rings. Popular for sealing rods and pistons in medium to heavy duty
applications and are compatible with both single and double acting cylinders.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
54
Metric
Rod Seals
55
Metric
Rod Seals
MVS-225X250X51.50
MVS-230X260X45
MVS-230X260X60-VIT
MVS-230X260X62
MVS-240X270X62.50
MVS-245X275X47.50
MVS-245X275X60
MVS-245X275X62.50
MVS-250X275X39.50
MVS-250X275X51.50
MVS-250X280X32
MVS-250X280X45
MVS-250X280X60
MVS-260X280X32
MVS-260X290X60
MVS-260X300X58
MVS-268X300X50
MVS-270X300X47.50
MVS-270X300X62.50
MVS-280X310X45
MVS-280X310X60
MVS-280X325X58
MVS-290X320X35
MVS-290X320X49
MVS-290X320X64
MVS-320X360X58
MVS-320X360X78
MVS-330X370X60
MVS-360X390.74X40
MVS-380X420X60
MVS-380X420X80
MVS-490X530X76
MVS-650X690X83
New parts are always being added. Call for sizes not shown and seal kits.
56
Metric
Rod Seals
AG Rod Seal
Temperature: -22 to 212 F (-30 to 100 C)
Max. Pressure: 5000 p.s.i.
Prefix ID OD Height
Comprised of a nitrile rubber sealing ring, a support ring of polyester elastomer, and a backup ring of
acetal resin. The housing dimensions are nominal.
Part Number
57
Metric
Rod Seals
Prefix ID OD Height
Height
A split steel bushing with a bronze lining and PTFE lining over
the bronze. These bushings possess excellent wear ability and
tremendous compressive strength.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
58
Metric
Rod Seals
59
Metric
Rod Seals
60
Metric
Rod Seals
Additional Profiles
609
RJS
61
Metric
Wipers
Metric
Wipers
Metric
Buffers
New parts are always being added. Call for sizes not shown and seal kits.
62
Metric
Wipers
63
Metric
Buffers
Prefix ID OD Height
Part Number
HBY-40X55.5X6 HBY-110X125.5X6
HBY-45X55.7X4 HBY-115X130.5X6
HBY-45X60.5X6 HBY-120X135.5X6
HBY-50X65.5X6 HBY-125X140.5X6
HBY-55X70.5X6 HBY-130X145.5X6
HBY-56X71.5X6 HBY-135X150.5X6
HBY-60X75.5X6 HBY-140X155.5X6
HBY-63X78.5X6 HBY-145X160.5X6
HBY-65X80.5X6 HBY-150X165.5X6
HBY-70X85.5X6 HBY-155X170.5X6
HBY-75X90.5X6 HBY-160X175.5X6
HBY-75X90.5X6.3-653 HBY-170X185.5X6
HBY-80X95.5X6 HBY-180X195.5X6
HBY-85X100.5X6 HBY-210X231X7.7
HBY-90X105.5X6 HBY-250X280X15-653
HBY-95X110.5X6
HBY-100X115.5X6
HBY-105X120.5X6
New parts are always being added. Call for sizes not shown and seal kits.
64
Metric
Buffers
Prefix ID OD Height
Molded in PTFE with a rubber energizer, this seal absorbs the shock of
pressure spikes to protect the rod seal.
A 2pc step buffer can be used in tandem of 2-5 to create a positive seal
or rod seal. Technical guidance is suggested if designing a cylinder with
this option.
Part Number
65
Metric
Buffers
MSBR-105X120.5X6 MSBR-180X201X8.1
MSBR-105X120.5X6-EX MSBR-190X205.1X6
MSBR-110X125.5X6 MSBR-190X215X9.5-EX
MSBR-110X125.5X6-EX MSBR-190X215X9.6
MSBR-110X131X8.1 MSBR-200X215.5X6
MSBR-115X130.5X6 MSBR-200X220.5X8
MSBR-115X130.5X6-EX MSBR-200X221X8.1
MSBR-120X135.5X6 MSBR-200X221X8.1-U
MSBR-120X135.5X6-EX MSBR-200X225X9.5-EX
MSBR-120X140.5X6-EX MSBR-200X225.5X9.5
MSBR-125X140.5X6 MSBR-200X227.5X9.5
MSBR-125X140.5X6-EX MSBR-200X227.5X9.5-EX
MSBR-130X145.5X6 MSBR-200X227.5X9.5-U
MSBR-130X145.5X6-EX MSBR-200X230X9-EX
MSBR-135X150.5X6-EX MSBR-200X230X9-U
MSBR-140X155.5X6 MSBR-210X231X7.9
MSBR-140X155.5X6-EX MSBR-210X235X9.5
MSBR-140X160.5X8.1 MSBR-220X241X8
MSBR-150X165.5X6 MSBR-220X241X8.1-U
MSBR-150X165.5X6-EX MSBR-220X245X8.2-NBR
MSBR-150X170.5X8.1 MSBR-220X245X9.5
MSBR-150X170.5X8.1-EX MSBR-230X250.5X7.9
MSBR-150X170.5X8.1-U MSBR-230X251X8.1
MSBR-160X175.5X6 MSBR-240X261X8.1
MSBR-160X179.25X9.5 MSBR-250X271X8.1
MSBR-160X180.5X8.1 MSBR-255X277X7
MSBR-160X180.5X8.1-U MSBR-260X284.5X8.1
MSBR-165X180.5X6 MSBR-260X287.3X9.5
MSBR-170X185.5X6 MSBR-265X289.5X8.1
MSBR-170X190.5X8.1 MSBR-270X295.5X9.5
MSBR-170X190.5X8.1-EX MSBR-280X300X8.3
MSBR-170X190.5X8.1-U MSBR-295X319.5X8.1
MSBR-175X190.5X6 MSBR-300X327.3X9.5
MSBR-180X195.5X6
New parts are always being added. Call for sizes not shown and seal kits.
66
Metric
Buffers
Additional Profiles
MIR
67
Metric
Wipers
Metric
Wipers
Metric
Rod/Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
68
Metric
Wipers
69
Metric
Rod/Piston Seals
Prefix ID OD Height
How to determine groove size:
Bore = 100mm
Groove size = 80mm
Seal Height = 10mm
Seal Groove Height = 10mm x 1.1 = 11mm
NRS rod shim with seal increases pressure capability. -R Rubber Max Pressure: 800 PSI
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
70
Metric
Rod/Piston Seals
71
Metric
Rod/Piston Seals
72
Metric
Rod/Piston Seals
MUS-136X150X8.5 MUS-220X240X12
MUS-136X154X9 MUS-220X250X15-R
MUS-140X155X8.9 MUS-220X250X17
MUS-140X160X15 MUS-230X240X7.3
MUS-140X160X15-N MUS-230X250X12
MUS-145X160X8.9 MUS-235X255X10
MUS-145X165X15 MUS-235X255X12
MUS-150X165X8.9 MUS-240X260X12
MUS-150X170X15 MUS-240X260X18
MUS-150X180X15 MUS-240X265X18
MUS-155X180X15 MUS-250X275X18
MUS-160X175X9 MUS-250X280X22
MUS-160X180X15 MUS-255X280X19
MUS-160X185X15 MUS-260X290X18
MUS-165X180X9 MUS-265X295X18
MUS-165X183X10 MUS-270X300X18
MUS-165X190X15 MUS-280X310X18
MUS-165X190X16 MUS-290X320X18
MUS-165X195X25 MUS-300X330X18
MUS-170X190X15 MUS-360X390X22
MUS-170X195X15 MUS-375X405X22
MUS-170X200X26 MUS-400X425X25
MUS-175X190X9 MUS-450X485X25
MUS-175X200X15
MUS-175X200X16-R
MUS-175X200X18-R
MUS-180X200X12
MUS-180X205X15
MUS-190X210X12
MUS-190X215X15
MUS-200X220X12
MUS-200X225X15
MUS-210X235X18
MUS-216X225X15
73
Metric
Wipers
Metric
Wipers
Metric
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
74
Metric
Wipers
75
Metric
Piston Seals
Prefix ID OD Height
How to determine groove size:
Bore = 100mm
Groove size = 80mm ID OD
Seal Height = 10mm
Seal Groove Height = 10mm x 1.1 = 11mm
NRS rod shim with seal increases pressure capabilities. -R Rubber Max Pressure: 800 PSI
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
76
Metric
Piston Seals
77
Metric
Piston Seals
-U is urethane.
*These part numbers are OD X Height X Cross Section of PTFE or urethane ring.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
78
Metric
Piston Seals
79
Metric
Piston Seals
MPS-450X425.5X8.1-U
MPS-480X459X8.1
MPS-560X532X10
New parts are always being added. Call for sizes not shown and seal kits.
80
Metric
Piston Seals
A double acting seal capable of passing over ports, the OK expands and contracts to fill the gap between the piston and the cylinder
wall and has a step-cut joint for ease of installation. It will tolerate a considerable extrusion gap, thus reducing the possibility of
piston to bore contact. The square nitrile rubber energiser responds quickly to pressure changes, providing excellent sealing
characteristics under all pressure conditions.
Part Number
81
Metric
Piston Seals
OK-480X452X9.5
New parts are always being added. Call for sizes not shown and seal kits.
82
Metric
Piston Seals
Part Number
83
Metric
Piston Seals
MCPS-195X175X16
MCPS-200X169X23
MCPS-200X177X15.5
MCPS-200X181.5X18.5
MCPS-210X187X15.5
MCPS-220X197X15.5
MCPS-225X202X15.5
MCPS-225X205X20
MCPS-230X207X15.5
MCPS-230X210X15.5
MCPS-240X215X25-730
MCPS-240X217X15.5
MCPS-250X212X26
MCPS-250X222X17
MCPS-260X232X17
MCPS-260X235X25-730
MCPS-280X252X17
MCPS-280X255X25
MCPS-300X262X25.5
MCPS-300X272X17
MCPS-300X275X25-730
MCPS-300X275X25
MCPS-310X285X25-730
MCPS-330X305X30-730
MCPS-345X315X30
MCPS-360X322.4X26.4
MCPS-360X332X17.5
New parts are always being added. Call for sizes not shown and seal kits.
84
Metric
Piston Seals
Part Number
85
Metric
Piston Seals
TDE-110X90X25.4X6.35 TDE-190X160X35.4X6.35
TDE-110X90X31X7 TDE-200X170X35.4X6.35
TDE-110X96X22.5X5.2 TDE-200X170X44X12
TDE-115X90X22.4X6.35 TDE-200X180X31.5X9.2
TDE-120X95X22.4X6.35 TDE-210X180X31.7X6.45
TDE-120X100X31X7 TDE-210X180X32.4X6.35
TDE-120X106X22.5X5.2 TDE-220X190X35.4X6.35
TDE-125X100X25X6.45 TDE-250X220X35.4X6.35
TDE-125X100X25.4X6.35 TDE-250X230X31.5X9.2
TDE-125X100X31X6.9
TDE-125X100X32.4X6.35
TDE-125X100X38X9.5
TDE-125X105X25.4X6.35
TDE-125X108X26.5X7.2
TDE-130X105X25.4X6.35
TDE-135X110X25.4X6.35
TDE-140X115X25.4X6.35
TDE-140X120X25.4X6.35
TDE-140X120X31X7
TDE-140X123X26.5X7.2
TDE-145X120X25.4X6.35
TDE-145X125X31X7
TDE-150X120X38.4X6.35
TDE-150X120X44X9.5
TDE-150X133X26.5X7.2
TDE-155X130X25.4X6.35
TDE-160X130X25.4X6.35
TDE-160X143X26.5X7.2
TDE-170X140X25.4X6.35
TDE-180X150X35X6.45
TDE-180X150X35.4X6.35
TDE-180X160X31X7
TDE-180X160X31.4X6.35
TDE-180X163X26.5X7.2
New parts are always being added. Call for sizes not shown and seal kits.
86
Metric
Piston Seals
Part Number
87
Metric
Piston Seals
88
Metric
Piston Seals
TPM-195X170X25.3X12.7
TPM-200X170X35.3X6.4
TPM-200X170X36X12.5
TPM-200X175X25.3X12.7
TPM-200X175X31.5X6.6
TPM-200X175X31.5X6.6-753
TPM-200X175X45X12.7
TPM-210X185X25.3X12.7
TPM-210X185X45X12.7
TPM-220X190X35.3X6.4
TPM-220X190X36X12.5
TPM-220X195X25.3X12.7
TPM-220X195X45X12.7
TPM-230X205X25.3X12.7
TPM-230X205X45X12.7
TPM-240X215X25.3X12.7
TPM-240X215X45X12.7
TPM-250X220X35.3X6.4
TPM-250X220X36X12.5
TPM-250X225X25.3X12.7
TPM-250X225X45X12.7
TPM-250X230X31.5X9.2
TPM-280X250X36X12.5
TPM-280X250X36.3X10
TPM-280X255X45X12.7
TPM-290X265X45X12.7
TPM-300X275X45X12.7
TPM-320X290X36X12.5
TPM-350X325X45X12.7
89
Metric
Piston Seals
Groove Width: To permit the ring to slide freely into the groove, the groove must be
at least 0.001 inches wider than the maximum piston ring width with a tolerance of
+0.003/-0 inches.
Groove Depth: Grooves must be at least 0.015 inches deeper than the maximum
radial wall thickness of the piston ring with a tolerance of +0.003/-0 inches. This is to
avoid any possibility of the ring bottoming in the groove when the ring is compressed
to its working diameter.
Radial Clearance: The radial clearance between the cylinder bore and piston should
be less than 1/3 of the radial wall thickness of the piston ring to ensure sealing
effectiveness.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
90
Metric
Piston Seals
Additional Profiles
18 OUY
91
Metric
Wipers
Metric
Wipers
Metric
Wear Rings
New parts are always being added. Call for sizes not shown and seal kits.
92
Metric
Wipers
93
Metric
Wear Rings
Height
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
94
Metric
Wear Rings
95
Metric
Wear Rings
96
Metric
Wear Rings
97
Metric
Wear Rings
98
Metric
Wear Rings
99
Metric
Wear Rings
100
Metric
Wear Rings
MWR-330X25X5
MWR-340X25X2.5
MWR-340X34.5X3
MWR-340X180X6
MWR-350X25X2.5
MWR-360X39.5X3
MWR-360X40X6
MWR-370X24.5X5
MWR-380X25X2.5
MWR-380X39.8X3
MWR-381X63.5X5
MWR-390X39X3
MWR-400X25X2.5
MWR-400X34.8X2.5
MWR-400X39.8X2.5
MWR-400X63.5X4.75
MWR-420X59.3X3
MWR-430X25X2.5
MWR-450X25X2.5
MWR-480X25X2.5
MWR-480X25X5
101
Metric
Wear Rings
This wear ring is molded from glass reinforced nylon. This style
is highly recommended due to its strong wear rate and non-
scoring properties, as well as its ability to capture metal chips.
This range of TWR wear rings has been upgraded to replace the OD
PTFE out board wear rings on the piston.
Height
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
102
Metric
Wear Rings
TWR-175X6X4
TWR-180X7.9X2.5
TWR-180X9X4
TWR-180X9.5X4
TWR-190X9X4
TWR-190X9.5X4
TWR-200X9X4
TWR-200X9.5X4
TWR-210X8.9X4
TWR-215X9.7X4
TWR-220X9X4
TWR-240X15X4
TWR-300X34.5X2.5
TWR-360X39.5X2.5
TWR-500X9.5X4
103
Metric
Wear Rings
Manufactured to a variety of widths and thicknesses. PTFE affords low friction capabilities with low
compressive strength. The material also has the capability of capturing metal particles and keeping them
from the seal area.
Part Number
TWRS-6X4
TWRS-7.9X2
TWRS-7.9X2.5
TWRS-7.9X4
TWRS-8.9X4
TWRS-9.7X2
TWRS-9.7X2.5
TWRS-9.7X4
TWRS-14.8X4
TWRS-15X2
TWRS-15X2.5
TWRS-20X2.5
TWRS-20X4
TWRS-25X2.5
TWRS-25X4
TWRS-30X2.5
New parts are always being added. Call for sizes not shown and seal kits.
104
Metric
Wear Rings
Extremely effective, hard wearing and easy to use bearing material. Manufactured to very strict
tolerances and provides bearing solutions for reciprocating, oscillating and slow rotary movement
applications. Capable of withstanding extreme side-loads and preventing metal to metal contact. The
materials design incorporates micro indentations on the bearing strips surface to trap fluid and provide
built-in lubrication to the bearing.
Part Number
MWRS-5.6X2.5
MWRS-9.7X2.5
MWRS-15X2
MWRS-15X2.5
MWRS-20X2.5
MWRS-20X3
MWRS-20X4
MWRS-25X2.5
MWRS-25X3
MWRS-40X2.5
105
Metric
Wear Rings
OD
Piston anti-extrusion rings used in cylinders for the construction industry, they help contain the piston
seal and stop extrusion.
Two pieces with one on either side of piston seal. Commonly green in colour but may come in black.
Part Number
PER-85X2.5X2.5
PER-95X2.5X2.5
PER-100X2.5X2.5
PER-105X2.5X2.5
PER-110X2.5X2.5
PER-110X3X3
PER-115X3X3
PER-120X3X3
PER-125X3X3
PER-130X3X3
PER-135X3X3
PER-140X3X3
PER-145X3X3
PER-150X3X3
PER-170X3X3
PER-190X3X3
PER-310X3X3
PER-390X3.5X3.5
New parts are always being added. Call for sizes not shown and seal kits.
106
Notes
107
Metric
Wipers
Metric
Wipers
Sakagami
New parts are always being added. Call for sizes not shown and seal kits.
108
Metric
Wipers
109
Sakagami
Sakagami Profiles
GPY-Packings STR-Seals
Piston packings Piston seals
GNY-Packings ST-Seals
Piston seals
Rod packings
SMJ-Seal
RGY-Packings
Rod seal
Piston packings
PGY-Packings
RNY-Packings
Piston packings
Rod packings
PNY-Packings
SGY-Packings Rod packings
Piston packings
GLY-Packings
SNY-Packings Piston & rod packings
Rod packings
PPD-Packings
SKY-Packings Piston packings
Piston & rod packings
PSD-Packings
KY-Packings Piston packings
Piston & rod packings PDU-Packings
Rod packings
RGU-Packings
Piston packings Mini Y-Packings
MYA*MYN
HSD-Packings Piston & rod packings
Piston packings MYP-Packings
PENTA-Seals PS Piston packings
Rod packings
MYR-Packings
NMY-Packings Rod packings
Rod packings
New parts are always being added. Call for sizes not shown and seal kits.
110
Sakagami
Sakagami Profiles
PPY-Packings S-LEEVE
Piston packings (WRB type)
PRY-Packings
PWL-Bearings
Rod packings
Piston bearings
SCK-Wipers PCS-Cushion Seals Metal Jacket
Rod wipers (SPC: Low
carbon steel)
SDR-Wipers
Rod wipers
SDB-Wipers
Metal Jacket
Rod wipers (SPC: Low
carbon steel)
SCB-Wipers
Metal Jacket
Rod wipers (SPC: Low
carbon steel)
SER-Wipers
Rod wipers
SFR-Wipers
Rod wipers
SW-Wear Rings
Piston wear rings
SWA-Wear Rings
Piston wear rings
SWB-Wear Rings
Piston wear rings
S-LEEVE
(WPB type)
111
Metric
Wipers
Metric
Wipers
Metric
O-rings
New parts are always being added. Call for sizes not shown and seal kits.
112
Metric
Wipers
113
Metric
O-Rings
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
114
Metric
O-Rings
115
Metric
O-Rings
116
Metric
O-Rings
117
Metric
O-Rings
118
Metric
O-Rings
119
Metric
O-Rings
120
Metric
O-Rings
121
Metric
O-Rings
122
Metric
O-Rings
123
Metric
O-Rings
124
Metric
O-Rings
125
Metric
O-Rings
126
Metric
O-Rings
127
Metric
O-Rings
128
Metric
O-Rings
129
Metric
O-Rings
130
Metric
O-Rings
131
Metric
O-Rings
132
Metric
O-Rings
133
Metric
O-Rings
134
Metric
O-Rings
135
Metric
O-Rings
136
Metric
O-Rings
137
Metric
O-Rings
138
Metric
O-Rings
139
Metric
O-Rings
140
Metric
O-Rings
141
Metric
O-Rings
142
Metric
O-Rings
143
Metric
O-Rings
144
Metric
O-Rings
145
Metric
O-Rings
146
Metric
O-Rings
147
Metric
O-Rings
148
Metric
O-Rings
149
Metric
O-Rings
150
Metric
O-Rings
151
Metric
O-Rings
152
Metric
O-Rings
153
Metric
O-Rings
154
Metric
O-Rings
GDS Seal
These are a urethane seal that is used as a replacement for an O-ring and backup.
These seals provide excellent sealing in high pressure applications. These
seals are not subject to breakage due to rolling as O-rings can sometimes.
These seals work for static and reciprocating applications. Working Temperature
-40 to 212 F (-40 to 100 C). Part Number = Groove Sizes
155
Metric
O-Rings
Molded from PTFE, these backup rings provide excellent extrusion resistance.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
156
Metric
O-Rings
157
Metric
O-Rings
158
Metric
O-Rings
159
Metric
O-Rings
Molded from urethane, these backup rings provide excellent extrusion resistance. When stretched for
installation, they quickly rebound to their original size.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
160
Metric
O-Rings
MUB-95X2.5X1.3 MUB-165X5X1.7
MUB-95X5X1.7 MUB-170X5X1.7
MUB-98X2.5X1.3 MUB-175X5X1.7
MUB-100X2.5X1.3 MUB-180X5X1.7
MUB-100X5X1.7 MUB-185X5X1.7
MUB-102X5X1.7 MUB-190X5X1.7
MUB-105X2.5X1.3 MUB-195X5X1.7
MUB-105X5X1.7 MUB-200X5X1.7
MUB-110X2.5X1.3 MUB-210X5X1.7
MUB-110X5X1.7 MUB-215X5X1.7
MUB-112X5X1.7 MUB-220X5X1.7
MUB-115X2.5X1.3 MUB-230X5X1.7
MUB-115X5X1.7 MUB-240X5X1.7
MUB-120X1.75X2.3 MUB-245X5X1.7
MUB-120X2.5X1.3 MUB-250X5X1.7
MUB-120X5X1.7 MUB-300X5X1.7
MUB-125X2.5X1.3 MUB-416X6X3
MUB-125X5X1.7
MUB-130X2.5X1.3
MUB-130X5X1.7
MUB-132X5X1.7
MUB-135X2.5X1.3
MUB-135X5X1.7
MUB-135X5X2
MUB-140X2.5X1.3
MUB-140X5X1.7
MUB-145X2.5X1.3
MUB-145X5X1.7
MUB-145X7.5X2.1
MUB-150X5X1.7
MUB-155X4.5X2
MUB-155X5X1.7
MUB-155X7.5X2.1
MUB-160X5X1.7
161
Metric
O-Rings
Groove Designs
P P P
r1 r1
d1
L L1 L2
d2
New parts are always being added. Call for sizes not shown and seal kits.
162
Metric
O-Rings
Groove Designs
C/S d2 Pressure No Back-up One Back-up Two Back-up Radius
(mm) Stat Dynam Pneum P (mm) L (mm) P (mm) L1 (mm) P (mm) L2 (mm) (r1)
163
Metric
O-Rings
New parts are always being added. Call for sizes not shown and seal kits.
164
Metric
O-Rings
165
Metric
O-Rings
New parts are always being added. Call for sizes not shown and seal kits.
166
Metric
O-Rings
Additional Profiles
MORC
O-ring Cord is supplied as a continuous extruded cord. O-ring cord can be used to fabricate custom
O-rings where the standard sizes are not suitable. O-rings can be made from the following compounds:
Fluorocarbon
Silicone
Silicone Sponge
EPDM
Natural Rubber (pure gum)
Aflas
Nitrile
FDA Nitrile
Neoprene
Highly saturated Nitrile (HSN)
Isoprene
Urethane
PTFE
EPDM/Neoprene Sponge
SBR (Styrene Butadiene)
Latex
In addition to standard rubber cords, the following profiles are available in various compounds:
Square
Rectangular
Quad
U-channels
Tubing
167
Metric
Wipers
Metric
Wipers
Metric
Miscellaneous
New parts are always being added. Call for sizes not shown and seal kits.
168
Metric
Wipers
169
Metric
Miscellaneous
Prefix ID OD Height
Used to back up rod and piston seals, these provide excellent extrusion resistance. When used with a
u-cup, these shims make it capable for the seal to handle higher pressures.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
170
Metric
Miscellaneous
171
Metric
Miscellaneous
Rotary Seal
Prefix ID OD Height
Call for PTFE rotary (swivel) seals used on piston and post
style set ups.
Part Number
ROTARY-60X70X5
ROTARY-70X80X5
ROTARY-75X85X5
ROTARY-80X90X5
ROTARY-90X100X5
ROTARY-95X105X5
ROTARY-100X110X5
ROTARY-110X120X5
ROTARY-120X130X5
ROTARY-140X150X5
ROTARY-180X190X5
New parts are always being added. Call for sizes not shown and seal kits.
172
Metric
Miscellaneous
Prefix ID OD L1 L2
ID OD
20~30
Part Number
RI-16X24X1.3/4.5-A
RI-32X40X1.85/5-A
RI-32X42X1.85/5-A
RI-36X46X1.85/5-A
RI-40X50X2.15/5-A
RI-45X55X2.15/5-A
RI-50X60X2.15/5-A
RI-50X65X2.65/6-A
RI-63X78X2.65/6-A
RI-63X83X2.65/6-A
RI-75X90X3.15/6-A
RI-90X105X4.15/6-A
173
Metric
Miscellaneous
Additional Profiles
BS, USIT
GAMMA
Call for profiles not shown. Please call for all metric oil seals and metric o-ring kits.
New parts are always being added. Call for sizes not shown and seal kits.
174
Notes
175
Metric
Wipers
Inch
Metric
Wipers
Wipers
New parts are always being added. Call for sizes not shown and seal kits.
176
Metric
Wipers
177
Inch
Wipers
Prefix ID OD Height
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
178
Inch
Wipers
179
Inch
Wipers
MC-4.250X4.875X.312 MC-8.125X8.625X.312
MC-4.250X5.250X.500 MC-8.50X9.125X.375
MC-4.375X5.00X.312 MC-9.00X9.750X.562
MC-4.500X5.125X.312 MC-9.00X10.00X.625
MC-4.500X5.250X.312 MC-9.750X10.250X.312
MC-4.500X5.500X.312 MC-11.00X12.00X.500
MC-4.500X5.500X.500 MC-12.500X13.500X.550
MC-4.750X5.375X.312
MC-4.750X5.750X.500
MC-5.00X5.625X.312
MC-5.00X5.750X.312
MC-5.00X6.00X.500
MC-5.250X5.750X.312
MC-5.250X5.875X.312
MC-5.250X6.00X.312
MC-5.250X6.250X.500
MC-5.500X6.125X.375
MC-5.500X6.250X.312
MC-5.50X6.50X.500
MC-5.750X6.375X.375
MC-5.750X6.750X.500
MC-6.00X6.625X.375
MC-6.00X6.750X.375
MC-6.00X7.00X.500
MC-6.500X7.250X.312
MC-6.500X7.500X.500
MC-6.750X7.250X.312
MC-6.750X7.375X.375
MC-6.750X7.750X.500
MC-7.00X7.750X.312
MC-7.00X8.00X.500
MC-7.250X8.250X.500
MC-8.00X8.750X.375
MC-8.00X9.00X.500
New parts are always being added. Call for sizes not shown and seal kits.
180
Inch
Wipers
D Snap in Wiper
Temperature: -40 to 212 F (-40 to 100 C) E
Max. Speed: 1.0 m/s (3.0 ft/sec)
B
This urethane wiper is ideal for most applications,
including contaminated environments. Flexible enough
to easily snap into a groove, but durable enough to
handle difficult rod wiping applications.
A ID F D
Some seals available in alternative materials; call for
availability.
181
Inch
Wipers
D Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
ID A B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Diameter Outer Thickness Inches Diameter Height Diameter
Inches Dia. Max. +.006 +.004 +.010
-.000 -.000 -.000
New parts are always being added. Call for sizes not shown and seal kits.
182
Inch
Wipers
D Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
ID A B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Diameter Outer Thickness Inches Diameter Height Diameter
Inches Dia. Max. +.006 +.004 +.010
-.000 -.000 -.000
183
Inch
Wipers
D Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
ID A B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Diameter Outer Thickness Inches Diameter Height Diameter
Inches Dia. Max. +.006 +.004 +.010
-.000 -.000 -.000
New parts are always being added. Call for sizes not shown and seal kits.
184
Inch
Wipers
D Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
ID A B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Diameter Outer Thickness Inches Diameter Height Diameter
Inches Dia. Max. +.006 +.004 +.010
-.000 -.000 -.000
185
Inch
Wipers
D Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
ID A B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Diameter Outer Thickness Inches Diameter Height Diameter
Inches Dia. Max. +.006 +.004 +.010
-.000 -.000 -.000
New parts are always being added. Call for sizes not shown and seal kits.
186
Inch
Wipers
187
Inch
Wipers
New parts are always being added. Call for sizes not shown and seal kits.
188
Inch
Wipers
189
Inch
Wipers
New parts are always being added. Call for sizes not shown and seal kits.
190
Inch
Wipers
H Snap in Wiper
E
Temperature: -40 to 212 F (-40 to 100 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
B
Urethane wiper designed for medium duty applications
and can provide both wiping and sealing action in one
component in low pressure systems. The external
lip scrapes foreign matters from the rod, and the
D1 A F D
internal lip acts as an effective pressure seal in low
pressure applications. This wiper can also be used as a
secondary seal to trap slight leakage from the primary
seal. This creates a very dry rod system.
H-0250 0.250 0.562 0.194 0.250 +.000 -.001 0.552 +.002 -.000 0.203 0.370 +.002 -.000
H-0312 0.312 0.625 0.194 0.312 +.000 -.001 0.615 +.002 -.000 0.203 0.432 +.002 -.000
H-0375 0.375 0.688 0.194 0.375 +.000 -.001 0.677 +.002 -.000 0.203 0.495 +.002 -.000
H-0500 0.500 0.813 0.194 0.500 +.000 -.001 0.802 +.002 -.000 0.203 0.620 +.002 -.000
H-0625 0.625 0.938 0.194 0.625 +.000 -.001 0.927 +.002 -.000 0.203 0.745 +.002 -.000
H-0750 0.750 1.062 0.194 0.750 +.000 -.001 1.052 +.002 -.000 0.203 0.870 +.002 -.000
H-0875 0.875 1.250 0.212 0.875 +.000 -.001 1.240 +.002 -.000 0.218 1.010 +.002 -.000
H-0937 0.937 1.312 0.212 0.937 +.000 -.001 1.302 +.003 -.000 0.218 1.072 +.003 -.000
H-1000 1.000 1.375 0.212 1.000 +.000 -.001 1.365 +.003 -.000 0.218 1.135 +.003 -.000
H-1125 1.125 1.500 0.212 1.125 +.000 -.001 1.490 +.003 -.000 0.218 1.260 +.003 -.000
H-1250 1.250 1.625 0.212 1.250 +.000 -.001 1.615 +.003 -.000 0.218 1.385 +.003 -.000
H-1375 1.375 1.750 0.212 1.375 +.000 -.001 1.740 +.003 -.000 0.218 1.510 +.003 -.000
H-1500 1.500 1.875 0.212 1.500 +.000 -.001 1.865 +.003 -.000 0.218 1.635 +.003 -.000
H-1625 1.625 2.000 0.212 1.625 +.000 -.001 1.990 +.003 -.000 0.218 1.760 +.003 -.000
H-1750 1.750 2.125 0.212 1.750 +.000 -.001 2.115 +.003 -.000 0.218 1.885 +.003 -.000
191
Inch
Wipers
H Snap in Wiper
Part Wiper Dimensions Groove Dimensions
Number A D1 B Rod D E F
Inner Seal Base Diameter Inches Groove Groove Throat
Dia. Outer Thickness Diameter Height Diameter
Dia. Max. +.005
-.000
H-1875 1.875 2.250 0.212 1.875 +.000 -.001 2.240 +.003 -.000 0.218 2.010 +.003 -.000
H-2000 2.000 2.375 0.212 2.000 +.000 -.001 2.365 +.003 -.000 0.218 2.135 +.003 -.000
H-2125 2.125 2.500 0.212 2.125 +.000 -.001 2.490 +.003 -.000 0.218 2.260 +.003 -.000
H-2250 2.250 2.750 0.275 2.250 +.000 -.001 2.745 +.003 -.000 0.281 2.385 +.003 -.000
H-2375 2.375 2.875 0.275 2.375 +.000 -.001 2.870 +.003 -.000 0.281 2.510 +.003 -.000
H-2500 2.500 3.000 0.275 2.500 +.000 -.001 2.995 +.003 -.000 0.281 2.635 +.003 -.000
H-2625 2.625 3.125 0.275 2.625 +.000 -.001 3.120 +.003 -.000 0.281 2.760 +.003 -.000
H-2750 2.750 3.250 0.275 2.750 +.000 -.001 3.245 +.003 -.000 0.281 2.885 +.003 -.000
H-3000 3.000 3.500 0.275 3.000 +.000 -.002 3.495 +.003 -.000 0.281 3.135 +.003 -.000
H-3250 3.250 3.750 0.275 3.250 +.000 -.002 3.745 +.003 -.000 0.281 3.260 +.003 -.000
H-3500 3.500 4.000 0.275 3.500 +.000 -.002 3.995 +.003 -.000 0.281 3.635 +.003 -.000
H-3625 3.625 4.125 0.275 3.625 +.000 -.002 4.120 +.003 -.000 0.281 3.760 +.003 -.000
H-3750 3.750 4.250 0.275 3.750 +.000 -.002 4.245 +.003 -.000 0.281 3.885 +.003 -.000
H-3875 3.875 4.375 0.275 3.875 +.000 -.002 4.370 +.003 -.000 0.281 4.010 +.003 -.000
H-4000 4.000 4.500 0.275 4.000 +.000 -.002 4.495 +.003 -.000 0.281 4.135 +.003 -.000
H-4500 4.500 5.000 0.275 4.500 +.000 -.002 4.995 +.003 -.000 0.281 4.635 +.003 -.000
H-4750 4.750 5.250 0.275 4.750 +.000 -.002 5.245 +.003 -.000 0.281 4.885 +.003 -.000
H-5000 5.000 5.500 0.275 5.000 +.000 -.002 5.495 +.003 -.000 0.281 5.135 +.003 -.000
H-5125 5.125 5.625 0.275 5.125 +.000 -.002 5.620 +.003 -.000 0.281 5.260 +.003 -.000
H-5250 5.250 5.750 0.275 5.250 +.000 -.002 5.745 +.003 -.000 0.281 5.385 +.003 -.000
H-5500 5.500 6.000 0.275 5.500 +.000 -.002 5.995 +.003 -.000 0.281 5.635 +.003 -.000
H-6000 6.000 6.500 0.275 6.000 +.000 -.002 6.495 +.003 -.000 0.281 6.135 +.003 -.000
H-6500 6.500 7.000 0.275 6.500 +.000 -.002 6.995 +.003 -.000 0.281 6.635 +.003 -.000
H-7000 7.000 7.500 0.275 7.000 +.000 -.002 7.495 +.003 -.000 0.281 7.135 +.003 -.000
H-8000 8.000 8.500 0.275 8.000 +.000 -.002 8.495 +.003 -.000 0.281 8.135 +.003 -.000
H-8500 8.500 9.000 0.275 8.500 +.000 -.002 8.995 +.003 -.000 0.281 8.635 +.003 -.000
H-10000 10.000 10.500 0.275 10.000 +.000 -.002 10.495 +.003 -.000 0.281 10.135 +.003 -.000
New parts are always being added. Call for sizes not shown and seal kits.
192
Inch
Wipers
K Snap in Wiper
E
Temperature: -40 to 212 F (-40 to 100 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
193
Inch
Wipers
K Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
A D1 B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Dia. Outer Thickness Inches Diameter Height Diameter
Dia. Max. +.000 +005 +005 +.005
-.002 -.000 -.000 -.000
New parts are always being added. Call for sizes not shown and seal kits.
194
Inch
Wipers
K Snap in Wiper
Part Number Wiper Dimensions Groove Dimensions
A D1 B Rod D E F
Inner Seal Base Diameter Groove Groove Throat
Dia. Outer Thickness Inches Diameter Height Diameter
Dia. Max. +.000 +005 +005 +.005
-.002 -.000 -.000 -.000
195
Inch
Wipers
Additional Profiles
33
Snap in wiper.
842
Excluder
KB
Snap in wiper.
SG
New parts are always being added. Call for sizes not shown and seal kits.
196
Additional Profiles
LDW
Snap in wiper.
197
Metric
Wipers
Metric
Inch Wipers
Rod Seals
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
198
Metric
Wipers
Part Number
199
Inch
Rod Seals
A standard B-lip profile loaded U cup utilizing a urethane shell energised by a high specification resilient
O-ring. At zero or low pressure, the O-ring helps to increase the sealing force preventing any bypass.
As pressure rises the sealing force increases and the O-ring provides complete lip actuation under most
conditions. The precision trimmed sealing lips ensure optimum sealing action. It can be used for single
acting applications or fitted back to back for double acting applications (while removing one O-ring loader
to prevent pressure trap).
-EX style comes with a double lip and built in anti-extrusion ring.
-V Fluorocarbon, -FM High temperature product, -PM Elastoplastic (usually orange in colour)
-DL is a double lip rod seal.
New parts are always being added. Call for sizes not shown and seal kits.
200
Inch
Rod Seals
201
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
202
Inch
Rod Seals
203
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
204
Inch
Rod Seals
205
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
206
Inch
Rod Seals
207
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
208
Inch
Rod Seals
209
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
210
Inch
Rod Seals
211
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
212
Inch
Rod Seals
213
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
214
Inch
Rod Seals
215
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
216
Inch
Rod Seals
217
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
218
Inch
Rod Seals
219
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
220
Inch
Rod Seals
LR-500-09.00-750-EX 9 10 3/4
LR-375-09.125-500 9 1/8 9 7/8 1/2
LR-375-09.125-625 9 1/8 9 7/8 5/8
LR-312-09.250-625 9 1/4 9 7/8 5/8
LR-375-09.250-625 9 1/4 10 5/8
LR-500-09.250-750 9 1/4 10 1/4 3/4
LR-312-09.375-625 9 3/8 10 5/8
LR-250-09.500-562 9 1/2 10 9/16
LR-375-09.500-625 9 1/2 10 1/4 5/8
LR-500-09.500-750 9 1/2 10 1/2 3/4
LR-500-09.500-750-PM 9 1/2 10 1/2 3/4
LR-312-09.625-625 9 5/8 10 1/4 5/8
LR-250-09.750-375 9 3/4 10 1/4 3/8
LR-250-09.750-562 9 3/4 10 1/4 9/16
LR-312-09.750-625 9 3/4 10 3/8 5/8
LR-375-09.750-625-HS125 9 3/4 10 1/2 5/8
LR-375-09.750-625-EX 9 3/4 10 1/2 5/8
LR-375-09.875-625 9 7/8 10 5/8 5/8
LR-250-10.00-562 10 10 1/2 9/16
LR-250-10.00-562-EX 10 10 1/2 9/16
LR-375-10.00-625 10 10 3/4 5/8
LR-375-10.00-625-EX 10 10 3/4 5/8
LR-500-10.00-750 10 11 3/4
LR-500-10.00-750-EX 10 11 3/4
LR-500-10.00-750-PM 10 11 3/4
LR-625-10.00-1000 10 11 1/4 1
LR-250-10.250-562 10 1/4 10 3/4 9/16
LR-375-10.250-500 10 1/4 11 1/2
LR-375-10.250-750 10 1/4 11 3/4
LR-500-10.250-750 10 1/4 11 1/4 3/4
LR-312-10.375-625 10 3/8 11 5/8
LR-250-10.500-562 10 1/2 11 9/16
LR-312-10.500-562-EX 10 1/2 11 1/8 9/16
LR-375-10.500-625 10 1/2 11 1/4 5/8
221
Inch
Rod Seals
New parts are always being added. Call for sizes not shown and seal kits.
222
Inch
Rod Seals
223
Inch
Rod Seals
LR-500-29.00-750 29 30 3/4
LR-500-30.750-750 30 3/4 31 3/4 3/4
LR-500-34.500-750 34 1/2 35 1/2 3/4
LR-500-38.00-750 38 39 3/4
LR-500-38.750-750 38 3/4 39 3/4 3/4
LR-500-42.00-750 42 43 3/4
LR-500-43.500-750 43 1/2 44 1/2 3/4
LR-500-44.125-750 44 1/8 45 1/8 3/4
LR-500-47.500-750 47 1/2 48 1/2 3/4
New parts are always being added. Call for sizes not shown and seal kits.
224
Inch
Rod Seals
ZS Z Seal
Operating conditions
Temperature: -40 to 248 F (-40 to 120 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
Max. Pressure: 400 bar (5800 p.s.i.)
Rod = 2.00 OD
Groove size = 2.500
Seal Height = .375
Seal Groove Height = .375 x 1.1 = .412
Has excellent sealing ability and low compression set. A resilient rubber lip with the greater anti-extrusion
characteristics of a hard thermoplastic base. Under low pressure conditions, the sealing lip provides its
own compressive seal force. As pressure increases, hydrostatic pressure is mechanically transmitted
through the elastomeric sealing element into the anti-extrusion base. The applied force then deflects
radially in a controlled manner, closing the extrusion gap behind the sealing lip. Under this condition,
maximum sealing effectiveness is achieved.
-F High temperature product, -FEX High temperature product with anti-extrusion ring, -EX with anti-
extrusion ring.
225
Inch
Rod Seals
ZS Z Seal
Part Number ID OD Height
226
Inch
Rod Seals
ZS Z Seal
Part Number ID OD Height
227
Inch
Rod Seals
Groove
Height
How to determine groove size:
Rod = 2.00
Groove size = 2.500
Seal Height = .375
Seal Groove Height = .375 x 1.1 = .412
ID OD
Maximum Extrusion Gap On One Side
Max. Gap:
0.6mm/.024in=160bar/2400psi
0.5mm/.020in=250bar/3750psi
0.4mm/.016in=400bar/6000psi Height
Molded in urethane, this seal employs an additional lip near the heel. The Twin Lip design provides
stability, friction-reducing lube retention, and contamination resistance. Made for light to medium duty
applications.
Most unloaded rod seals are double lip. Some items are single lip.
New parts are always being added. Call for sizes not shown and seal kits.
228
Inch
Rod Seals
229
Inch
Rod Seals
230
Inch
Rod Seals
231
Inch
Rod Seals
232
Inch
Rod Seals
233
Inch
Rod Seals
234
Inch
Rod Seals
235
Inch
Rod Seals
236
Inch
Rod Seals
237
Inch
Rod Seals
238
Inch
Rod Seals
UR-500-12.00-625 12 13 5/8
UR-500-12.00-690 12 13 11/16
UR-500-12.00-750 12 13 3/4
UR-562-12.00-625 12 13 1/8 5/8
239
Inch
Rod Seals
Rod = 2.00
Groove size = 2.500
Seal Height = .375 20~30
Height
A breakthrough in pneumatic sealing, the material and the profile of the dynamic sealing lip combine
to offer both ultra low friction - significantly less than that of rubber - and ultra long life. It has been
developed to give significant improvements in cylinder performance during low lube air conditions. Can be
used in long and short stroke applications.
New parts are always being added. Call for sizes not shown and seal kits.
240
Inch
Rod Seals
241
Inch
Rod Seals
VR Vee Ring
Operating conditions
Temperature: -40 to 248 F (-40 to 120 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
Max. Pressure: 400 bar (5800 p.s.i.)
Maximum extrusion gap Figures show the maximum permissible
gap all on one side using minimum rod
and maximum clearance .
Prefix ID OD
Vee rings manufactured from fabric reinforced nitrile rubber. Vee pack sets are multiple-lip (chevron) seals, usually composed of
a male and female adaptor and a group of three to five vee rings. Popular for sealing rods and pistons in medium to heavy duty
applications and are compatible with both single and double acting cylinders.
Available in Male and Female adapters, and Neo-Fab Vee rings. Other materials also available.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
242
Inch
Rod Seals
VR Vee Ring
Part Number
243
Inch
Rod Seals
VR Vee Ring
Part Number
244
Inch
Rod Seals
VR Vee Ring
Part Number
245
Inch
Rod Seals
VR Vee Ring
Part Number
246
Inch
Rod Seals
VR Vee Ring
Part Number
247
Inch
Rod Seals
VR Vee Ring
Part Number
VR-8.500X9.750-M VR-11.250X12.00-M
VR-8.500X10.062 VR-12.00X13.250
VR-8.500X10.062-F VR-12.00X13.250-F
VR-8.500X10.062-M VR-12.00X13.250-FN
VR-9.00X9.750 VR-12.00X13.250-M
VR-9.00X9.750-F VR-12.00X13.250-MN
VR-9.00X9.750-M VR-12.00X13.250-U
VR-9.00X10.00 VR-12.00X13.500
VR-9.00X10.00-F VR-12.00X13.500-F
VR-9.00X10.00-M VR-12.00X13.500-M
VR-9.00X10.25 VR-12.75X13.75
VR-9.00X10.25-F VR-12.75X13.75-F
VR-9.00X10.250-M VR-12.75X13.75-M
VR-9.00X10.50 VR-13.00X14.00
VR-9.00X10.50-F VR-13.875X14.875
VR-9.00X10.50-M VR-13.875X14.875-F
VR-9.375X9.875 VR-13.875X14.875-M
VR-9.375X10.00 VR-14.00X15.50
VR-9.75X10.50 VR-14.00X15.50-F
VR-9.75X10.50-F VR-15.50X16.50
VR-9.75X10.50-M VR-15.50X16.50-F
VR-9.875X10.625 VR-15.50X16.50-M
VR-9.875X10.625-F VR-16.00X17.00
VR-9.875X10.625-M VR-17.00X18.00
VR-10.00X11.500 VR-17.00X18.00-F
VR-10.00X11.500-F VR-17.00X18.00-M
VR-10.00X11.500-M
VR-10.375X11.375
VR-10.375X11.375-F
VR-10.375X11.375-M
VR-10.625X12.125
VR-10.750X12.00
VR-11.250X12.00
VR-11.250X12.00-F
New parts are always being added. Call for sizes not shown and seal kits.
248
Inch
Rod Seals
VS Vee Set
Operating conditions
Temperature: -40 to 248 F (-40 to 120 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
Max. Pressure: 400 bar (5800 p.s.i.)
Vee rings manufactured from fabric reinforced nitrile rubber. Vee pack sets are multiple-lip (chevron) seals, usually composed of
a male and female adaptor and a group of three to five vee rings. Popular for sealing rods and pistons in medium to heavy duty
applications and are compatible with both single and double acting cylinders.
Part Number
249
Inch
Rod Seals
VS Vee Set
Part Number
250
Inch
Rod Seals
VS Vee Set
Part Number
251
Inch
Rod Seals
TR Rod T Seal
Part Number Rod Diameter O-ring Groove Part Number Rod Diameter O-ring Groove
Dash Diameter Dash Diameter
252
Inch
Rod Seals
TR Rod T Seal
Part Number Rod Diameter O-ring Groove
Dash Diameter
253
Metric
Wipers
Metric
Wipers
Inch
New parts are always being added. Call for sizes not shown and seal kits.
254
Metric
Wipers
Part Number
255
Inch
Buffers
Height
Part Number
DYR28-1.25-12
DYR28-1.50-12
DYR28-1.75-12
DYR28-2.00-12
DYR31-2.75-22
DYR31-3.00-22
DYR31-3.50-22
DYR31-4.00-22
DYR34-2.25-22
DYR34-2.50-22
New parts are always being added. Call for sizes not shown and seal kits.
256
Inch
Buffers
Maximum extrusion gap Figures show the maximum permissible gap all on one
side using minimum rod and maximum clearance .
Molded in PTFE with a rubber energizer, this seal absorbs the shock of
pressure spikes to protect the rod seal.
A 2pc step buffer can be used in tandem of 2-5 to create a positive seal
or rod seal. Technical guidance is suggested if designing a cylinder with
this option.
Part Number Rod Groove Seal Width Groove Width Max Diametrical
Diameter Diameter Clearance (PSI)
1000 3000 5000
KR-06251 0.625 0.923 +0.004 -0.000 0.122 +/-0.005 1.260 +0.010 -0.000 0.012 0.006 0.004
KR-10001 1.000 1.298 +0.004 -0.000 0.122 +/-0.005 0.126 +0.010 -0.000 0.012 0.006 0.004
KR-11201 1.125 1.423 +0.003 -0.000 0.122 +/-0.005 0.126 +0.010 -0.000 0.012 0.006 0.004
KR-12502 1.250 1.674 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-15001 1.500 1.798 +0.003 -0.000 1.220 +/-0.005 0.126 +0.010 -0.000 0.012 0.006 0.004
KR-15002 1.500 1.924 +0.004 -0.000 1.550 +/-0.005 0.016 +0.010 -0.000 0.016 0.008 0.006
KR-15003 1.500 2.116 +0.004 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.001 0.008
KR-17502 1.750 0.174 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-20002 2.000 2.424 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-20003 2.000 2.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-22502 2.250 2.674 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-25002 2.500 2.924 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-25003 2.500 3.116 +0.005 -0.000 0.247 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-26203 2.625 3.241 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-27503 2.750 3.366 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-28753 2.875 3.491 +0.005 -0.000 0.235 +/-0.005 0.025 +0.010 -0.000 0.020 0.010 0.008
KR-30002 3.000 3.424 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-30003-B 3.000 3.500 +0.005 -0.000 0.265 +/-0.005 0.275 +0.010 -0.000 0.020 0.010 0.008
257
Inch
Buffers
KR-32503 3.250 3.866 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-35002 3.500 3.924 +0.004 -0.000 0.155 +/-0.005 0.166 +0.010 -0.000 0.016 0.008 0.006
KR-35003 3.500 4.116 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-35003-B 3.500 4.000 +0.005 -0.000 0.265 +/-0.005 0.275 +0.010 -0.000 0.020 0.010 0.008
KR-36203 3.625 4.241 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-37503 3.750 4.366 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-37503-B 3.750 4.250 +0.005 -0.000 0.265 +/-0.005 0.275 +0.010 -0.000 0.020 0.010 0.008
KR-40003 4.000 4.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-40003-653 4.000 4.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-40004 4.000 4.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-40004-B 4.000 4.624 +0.006 -0.000 0.305 +/-0.005 0.343 +0.010 -0.000 0.024 0.012 0.009
KR-42503 4.250 4.866 +0.006 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-42503-B 4.250 4.750 +0.005 -0.000 0.265 +/-0.005 0.275 +0.010 -0.000 0.020 0.010 0.008
KR-42504 4.250 5.080 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-45003 4.500 5.116 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-45004 4.500 5.330 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-47503 4.750 5.366 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-50003 5.000 5.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-50004 5.000 5.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.020 0.010 0.008
KR-50004-B 5.000 5.830 +0.006 -0.000 0.305 +/-0.005 0.325 +0.010 -0.000 0.024 0.012 0.009
KR-52503 5.250 5.866 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-55003 5.500 5.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.001 0.008
KR-55004 5.500 6.330 +0.005 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-60003 6.000 6.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-60004 6.000 6.830 +0.005 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-67503 6.750 7.366 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-67504 6.750 7.580 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-70003 7.000 7.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-70003-653 7.000 7.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-70004 7.000 7.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-75004 7.500 8.330 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-80004 8.000 8.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-85003 8.500 9.116 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-85003-653 8.000 8.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-90004 9.000 9.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
New parts are always being added. Call for sizes not shown and seal kits.
258
Inch
Buffers
KR Step
Notes
Buffer Ring
Part Number Rod Groove Seal Width Groove Width Max Diametrical
Diameter Diameter Clearance (PSI)
1000 3000 5000
KR-100004 10.000 10.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-105003 10.500 11.116 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
KR-105004 10.500 11.330 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-120004 12.000 12.830 +0.006 -0.000 0.305 +/-0.005 0.320 +0.010 -0.000 0.024 0.012 0.009
KR-130003 13.000 13.616 +0.005 -0.000 0.235 +/-0.005 0.247 +0.010 -0.000 0.020 0.010 0.008
259
Metric
Wipers
Metric
Wipers
Rod/Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
260
Metric
Wipers
261
Inch
Rod/Piston Seals
US Symmetrical U Cup
Operating conditions
Temperature: -50 to 230 F (-45 to 110 C)
Max. Speed: 1.0 m/s (3.0 ft/sec)
Max. Pressure: 400 bar (6000 p.s.i.)
Maximum extrusion gap Figures show the maximum permissible
gap all on one side using minimum
rod and maximum clearance and
for piston seals using the minimum
clearance and maximum bore .
This seal is a symmetrical design, suitable for both rod and piston
applications. Featuring good low pressure sealing abilities, and resistance to
extrusion at high pressures.
New parts are always being added. Call for sizes not shown and seal kits.
262
Inch
Rod/Piston Seals
US Symmetrical U Cup
Part Number ID OD Height
263
Inch
Rod/Piston Seals
US Symmetrical U Cup
Part Number ID OD Height
264
Inch
Rod/Piston Seals
US Symmetrical U Cup
Part Number ID OD Height
265
Inch
Rod/Piston Seals
-V is Fluorocarbon.
New parts are always being added. Call for sizes not shown and seal kits.
266
Inch
Rod/Piston Seals
267
Inch
Rod/Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
268
Inch
Rod/Piston Seals
269
Inch
Rod/Piston Seals
Additional Profiles
HDLV
Piston Bearings.
18
New parts are always being added. Call for sizes not shown and seal kits.
270
Notes
271
Metric
Wipers
Metric
Wipers
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
272
Metric
Wipers
LP Loaded Piston U Cup. . . . 274 775 Urethane Seal (2 Pc) . . . . 329 CIPR Cast Iron Piston Ring . . . . 349
UP Unloaded Piston U Cup. . . . 305 PSU Piston Seal . . . . . . . . . 330 PIP Ring . . . . . . . . . . . . . 351
LUC Leather U Cup. . . . . . . . 310 PSC Piston Seal . . . . . . . . . 331 Additional Profiles. . . . . . . . . 353
607 Air Piston U Cup. . . . . . . 311 CPS Capped Piston Seal (4 Pc). 334
1400 Piston Seal (2 Pc). . . . . . 313 53 Piston Seal (5 Pc) . . . . . . . 336
1600 Piston Seal (2 Pc). . . . . . 316 58 Piston Seal (3 Pc). . . . . . . 337
1850 PTFE Seal (2 Pc) . . . . . 318 65 Delta Seal. . . . . . . . . . . 339
2473 PTFE Seal (2 Pc) . . . . . 321 TP Piston T Seal. . . . . . . . . 340
PSQ Piston Seal (2 Pc). . . . . . 322 NF Neo-Fab Piston Cup . . . . . 344
914 Chem Cast (2 Pc) . . . . . . 324 RPC Rubber Piston Cup . . . . . 346
755 Urethane Seal (2 Pc) . . . . 326 NOPAK Piston Cup . . . . . . 347
770 Urethane Seal (2 Pc) . . . . 328 DEL Piston Cup . . . . . . . . . . 348
273
Inch
Piston Seals
Bore = 2.500
Groove size = 2.00 ID OD
Seal Height = .375
Seal Groove Height = .375 x 1.1 = .412
A standard profile loaded U cup utilizing a urethane shell energised by a high specification resilient O-ring.
At zero or low pressure, the O-ring helps to increase the sealing force preventing any bypass. As pressure
rises the sealing force increases and the O-ring provides complete lip actuation under most conditions.
The precision trimmed sealing lips ensure optimum sealing action. It can be used for single acting
applications or fitted back to back for double acting applications. May also be used as a rod seal.
New parts are always being added. Call for sizes not shown and seal kits.
274
Inch
Piston Seals
275
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
276
Inch
Piston Seals
277
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
278
Inch
Piston Seals
279
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
280
Inch
Piston Seals
281
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
282
Inch
Piston Seals
283
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
284
Inch
Piston Seals
285
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
286
Inch
Piston Seals
287
Inch
Piston Seals
288
Inch
Piston Seals
289
Inch
Piston Seals
290
Inch
Piston Seals
291
Inch
Piston Seals
292
Inch
Piston Seals
LP-500-05.00 6 5 1/2
LP-500-05.00-750 6 5 3/4
LP-437-05.125 6 5 1/8 7/16
LP-437-05.125-500 6 5 1/8 1/2
LP-375-05.250 6 5 1/4 3/8
LP-375-05.250-500 6 5 1/4 1/2
LP-375-05.250-625 6 5 1/4 5/8
LP-312-05.375 6 5 3/8 5/16
LP-312-05.375-625 6 5 3/8 5/8
LP-281-05.437 6 5 7/16 9/32
LP-250-05.500 6 5 1/2 1/4
LP-250-05.500PM 6 5 1/2 1/4
LP-250-05.500-375 6 5 1/2 3/8
LP-250-05.500-562 6 5 1/2 9/16
LP-125-05.750 6 5 3/4 1/8
LP-187-05.687 6 1/16 5 11/16 3/16
LP-500-05.125 6 1/8 5 1/8 1/2
LP-500-05.125-750 6 1/8 5 1/8 3/4
LP-375-05.375 6 1/8 5 3/8 3/8
LP-312-05.500 6 1/8 5 1/2 5/16
LP-312-05.500-625 6 1/8 5 1/2 5/8
LP-250-05.625 6 1/8 5 5/8 1/4
LP-625-05.00 6 1/4 5 5/8
LP-500-05.250 6 1/4 5 1/4 1/2
LP-375-05.500 6 1/4 5 1/2 3/8
LP-375-05.500-625 6 1/4 5 1/2 5/8
LP-250-05.750 6 1/4 5 3/4 1/4
LP-250-05.750-562 6 1/4 5 3/4 9/16
LP-187-05.875 6 1/4 5 7/8 3/16
LP-500-05.375 6 3/8 5 3/8 1/2
LP-437-05.500 6 3/8 5 1/2 7/16
LP-375-05.625 6 3/8 5 5/8 3/8
LP-375-05.625-625 6 3/8 5 5/8 5/8
LP-250-05.875 6 3/8 5 7/8 1/4
293
Inch
Piston Seals
294
Inch
Piston Seals
295
Inch
Piston Seals
296
Inch
Piston Seals
297
Inch
Piston Seals
298
Inch
Piston Seals
299
Inch
Piston Seals
300
Inch
Piston Seals
301
Inch
Piston Seals
302
Inch
Piston Seals
LP-500-15.00-750 16 15 3/4
LP-375-15.250-625 16 15 1/4 5/8
LP-312-15.375-625 16 15 3/8 5/8
LP-625-15.00 16 1/4 15 5/8
LP-375-15.500 16 1/4 15 1/2 3/8
LP-250-15.750-562 16 1/4 15 3/4 9/16
LP-500-15.500-750 16 1/2 15 1/2 3/4
LP-312-15.875 16 1/2 15 7/8 5/16
LP-250-16.00-375 16 1/2 16 3/8
LP-250-16.00-250 16 1/2 16 1/2
LP-500-15.750 16 3/4 15 3/4 1/2
LP-500-16.00-750 17 16 3/4
LP-375-16.250 17 16 1/4 3/8
LP-750-16.00-1250 17 1/2 16 1 1/4
LP-750-16.500 18 16 1/2 3/4
LP-625-16.750 18 16 3/4 5/8
LP-500-17.00 18 17 1/2
LP-500-17.00-750 18 17 3/4
LP-375-17.250 18 17 1/4 3/8
LP-625-17.250 18 1/2 17 1/4 5/8
LP-500-17.500 18 1/2 17 1/2 1/2
LP-500-18.00 19 18 1/2
LP-250-19.00 19 1/2 19 1/4
LP-250-19.00-312 19 1/2 19 5/16
LP-625-18.750 20 18 3/4 5/8
LP-500-19.00 20 19 1/2
LP-625-19.250 20 1/2 19 1/4 5/8
LP-500-19.500 20 1/2 19 1/2 1/2
LP-625-20.00 21 1/4 20 5/8
LP-250-21.00-312 21 1/2 21 5/16
LP-500-21.00 22 21 1/2
LP-250-22.500-312 23 22 1/2 5/16
LP-250-23.00 23 1/2 23 1/4
LP-375-23.00 23 3/4 23 3/8
303
Inch
Piston Seals
LP-500-23.00 24 23 1/2
LP-375-24.00-625 24 3/4 24 5/8
LP-250-24.500 25 24 1/2 1/4
LP-625-24.750 26 24 3/4 5/8
LP-500-26.00 27 26 1/2
LP-500-26.500 27 1/2 26 1/2 1/2
LP-375-26.750-625 27 1/2 26 3/4 5/8
LP-500-28.00 29 28 1/2
LP-375-29.00-625 29 3/4 29 5/8
LP-500-31.00 32 31 1/2
LP-500-32.00 33 32 1/2
LP-375-35.00-625 35 3/4 35 5/8
LP-375-37.00-625 37 3/4 37 5/8
LP-375-40.00-625 40 3/4 40 5/8
LP-375-40.00-625 40 3/4 40 5/8
LP-500-31.00 32 31 1/2
LP-500-32.00 33 32 1/2
LP-375-35.00-625 35 3/4 35 5/8
LP-375-37.00-625 37 3/4 37 5/8
LP-375-40.00-625 40 3/4 40 5/8
New parts are always being added. Call for sizes not shown and seal kits.
304
Inch
Piston Seals
Bore = 2.500
Groove size = 2.00
Seal Height = .375
Seal Groove Height = .375 x 1.1 = .412
ID OD
Maximum Extrusion Gap On One Side
Max. Gap:
0.6mm/.024in=160bar/2400psi
0.5mm/.020in=250bar/3750psi
0.4mm/.018in=400bar/6000psi Height
This singl e acting seal is molded from urethane and is specifically designed for piston applications.
The outer dynamic lip is shorter and more robust to provide improved sealing and compression set
characteristics over conventional U rings. The seal can be used by itself or fitted back to back in separate
grooves for double acting applications.
305
Inch
Piston Seals
306
Inch
Piston Seals
307
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
308
Inch
Piston Seals
309
Inch
Piston Seals
Part Number
LUC-1.750X2.50X.375F.480
LUC-2.00X3.00X.500F.593
LUC-2.750X4.00X.562F.656
LUC-3.25X4.50X.562F.625
LUC-3.750X5.00X562F.656
LUC-4.750X6.00X.750F.843
LUC-8.00X6.750X1.250
New parts are always being added. Call for sizes not shown and seal kits.
310
Inch
Piston Seals
311
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
312
Inch
Piston Seals
OD ID
Maximum extrusion gap Figures show the maximum permissible gap all on
one side using minimum clearance and maximum
bore .
A double acting piston seal for use in light to medium duty hydraulic
applications. A two piece design comprised of a standard size O-ring
energizing a square PTFE cap. It offers long wear, low friction and because
of its short assembly length, requires minimal space on the piston.
Groove Groove
Part Number OD
Diameter Height
313
Inch
Piston Seals
314
Inch
Piston Seals
315
Inch
Piston Seals
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
316
Inch
Piston Seals
317
Inch
Piston Seals
ID OD
Maximum extrusion gap Figures show the maximum permissible gap all on
one side using minimum clearance and maximum
bore .
PS-1900 series are specifically sized seals for certain OEM cylinders.
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
318
Inch
Piston Seals
319
Inch
Piston Seals
New parts are always being added. Call for sizes not shown and seal kits.
320
Inch
Piston Seals
ID OD
Maximum extrusion gap Figures show the maximum permissible gap all on
one side using minimum clearance and maximum
bore .
A double acting piston seal that is compact, and has low friction
for light to medium duty hydraulic applications. Comprised of a
filled PTFE ring for better mechanical strength and pre-loaded by a
standard O-ring.
Groove Groove
Part Number OD
Diameter Height
321
Inch
Piston Seals
Maximum extrusion gap Figures show the maximum permissible gap all on
one side using minimum clearance and maximum
bore . ID OD
Pressure p.s.i. 1500 2400 3750 5250
Max. Gap in 0.024 0.020 0.018 0.014
This seal combines low friction and positive sealing. The quad-ring provides sealing
at low pressures.
New parts are always being added. Call for sizes not shown and seal kits.
322
Inch
Piston Seals
323
Inch
Piston Seals
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
324
Inch
Piston Seals
325
Inch
Piston Seals
Maximum extrusion gap Figures show the maximum permissible gap all on one
side using minimum rod and maximum clearance .
Prefix OD
A compact, low friction seal for light to medium duty hydraulic applications.
Made of a tough urethane outer seal and energized by a square cut O-ring.
This seal, when installed, rebounds back to size(unlike PTFE piston seals).
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
326
Inch
Piston Seals
327
Inch
Piston Seals
Maximum extrusion gap Figures show the maximum permissible gap all on one
side using minimum rod and maximum clearance .
Prefix OD
A double acting piston seal. Compact, low friction seal for light
to medium duty hydraulic applications. It has been designed
to fit standard inch O-ring housings. This seal, when installed,
rebounds back to size(unlike PTFE piston seals).
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
328
Inch
Piston Seals
Maximum extrusion gap Figures show the maximum permissible gap all
on one side using minimum rod and maximum
clearance .
Prefix OD
Groove Groove
Part Number OD
Diameter Height
329
Inch
Piston Seals
ID OD
25
Groove
Height
Molded from urethane, this double acting piston seal is a one-piece design. The outer layer is tough, and
abrasion resistant, while the soft inner layer acts as a static seal.
Part Number
PSU-2.00X1.62X.312
PSU-2.00X1.75X.250
PSU-2.50X2.12X.312
PSU-2.50X2.12X.375
PSU-3.00X2.50X.375
PSU-3.00X2.62X.375
PSU-3.500X3.125X.375
PSU-4.00X3.50X.375
PSU-5.00X4.75X.500
New parts are always being added. Call for sizes not shown and seal kits.
330
Inch
Piston Seals
A double acting piston seal designed to fit into O-ring grooves. The crown produces a positive seal from
vacuum to high pressure due to the narrow contact area with the bore. The O-ring acts as a static seal as
well as an energizer.
PSC-106 3/8 3/16 3/32 0.374 +.002 -.000 0.188 +.000 -.002 0.150 +.005 -.000 0.372 +.000 -.002
PSC-108 7/16 1/4 3/32 0.436 +.002 -.000 0.250 +.000 -.002 0.150 +.005 -.000 0.434 +.000 -.002
PSC-109 1/2 5/16 3/32 0.499 +.002 -.000 0.313 +.000 -.002 0.150 +.005 -.000 0.497 +.000 -.002
PSC-203 9/16 5/16 1/8 0.561 +.002 -.000 0.315 +.000 -.002 0.185 +.005 -.000 0.559 +.000 -.002
PSC-204 5/8 3/8 1/8 0.624 +.002 -.000 0.378 +.000 -.002 0.185 +.005 -.000 0.622 +.000 -.002
PSC-205 11/16 7/16 1/8 0.686 +.002 -.000 0.440 +.000 -.002 0.185 +.005 -.000 0.684 +.000 -.002
PSC-206 3/4 1/2 1/8 0.749 +.002 -.000 0.503 +.000 -.002 0.185 +.005 -.000 0.747 +.000 -.002
PSC-207 13/16 9/16 1/8 0.811 +.002 -.000 0.565 +.000 -.002 0.185 +.005 -.000 0.809 +.000 -.002
PSC-208 7/8 5/8 1/8 0.874 +.002 -.000 0.628 +.000 -.002 0.185 +.005 -.000 0.872 +.000 -.002
PSC-209 15/16 11/16 1/8 0.936 +.002 -.000 0.690 +.000 -.002 0.185 +.005 -.000 0.934 +.000 -.002
PSC-210 1 3/4 1/8 1.000 +.002 -.000 0.754 +.000 -.002 0.185 +.005 -.000 0.998 +.000 -.002
PSC-211 1 1/16 13/16 1/8 1.062 +.002 -.000 0.816 +.000 -.002 0.185 +.005 -.000 1.060 +.000 -.002
PSC-212 1 1/8 7/8 1/8 1.125 +.002 -.000 0.879 +.000 -.002 0.185 +.005 -.000 1.123 +.000 -.002
PSC-213 1 3/16 15/16 1/8 1.187 +.002 -.000 0.941 +.000 -.002 0.185 +.005 -.000 1.185 +.000 -.002
PSC-214 1 1/4 1 1/8 1.250 +.002 -.000 1.004 +.000 -.002 0.185 +.005 -.000 1.248 +.000 -.002
PSC-215 1 5/16 1 1/16 1/8 1.312 +.002 -.000 1.066 +.000 -.002 0.185 +.005 -.000 1.310 +.000 -.002
PSC-216 1 3/8 1 1/8 1/8 1.375 +.002 -.000 1.129 +.000 -.002 0.185 +.005 -.000 1.373 +.000 -.002
PSC-217 1 7/16 1 3/16 1/8 1.437 +.002 -.000 1.191 +.000 -.002 0.185 +.005 -.000 1.435 +.000 -.002
PSC-218 1 1/2 1 1/4 1/8 1.500 +.002 -.000 1.254 +.000 -.002 0.185 +.005 -.000 1.498 +.000 -.002
PSC-218-WB 1 1/2 1 1/4 1/8 1.500 +.002 -.000 1.254 +.000 -.002 0.304 +.005 -.000 1.498 +.000 -.002
331
Inch
Piston Seals
PSC-219 1 9/16 1 5/16 1/8 1.562 +.002 -.000 1.316 +.000 -.002 0.185 +.005 -.000 1.560 +.000 -.002
PSC-220 1 5/8 1 3/8 1/8 1.625 +.002 -.000 1.379 +.000 -.002 0.185 +.005 -.000 1.623 +.000 -.002
PSC-222 1 3/4 1 1/2 1/8 1.750 +.002 -.000 1.504 +.000 -.002 0.185 +.005 -.000 1.748 +.000 -.002
PSC-222-WB 1 3/4 1 1/2 1/8 1.750 +.002 -.000 1.504 +.000 -.002 0.304 +.005 -.000 1.748 +.000 -.002
PSC-325 1 7/8 1 1/2 3/16 1.875 +.002 -.000 1.500 +.000 -.002 0.280 +.005 -.000 1.873 +.000 -.002
PSC-326 2 1 5/8 3/16 2.000 +.002 -.000 1.625 +.000 -.002 0.280 +.005 -.000 1.998 +.000 -.002
PSC-326-WB 2 1 5/8 3/16 2.000 +.002 -.000 1.625 +.000 -.002 0.424 +.005 -.000 1.998 +.000 -.002
PSC-327 2 1/8 1 3/4 3/16 2.125 +.002 -.000 1.750 +.000 -.002 0.280 +.005 -.000 2.123 +.000 -.002
PSC-328 2 1/4 1 7/8 3/16 2.250 +.002 -.000 1.875 +.000 -.002 0.280 +.005 -.000 2.248 +.000 -.002
PSC-329 2 3/8 2 3/16 2.375 +.002 -.000 2.000 +.000 -.002 0.280 +.005 -.000 2.373 +.000 -.002
PSC-330 2 1/2 2 1/8 3/16 2.500 +.002 -.000 2.125 +.000 -.002 0.280 +.005 -.000 2.498 +.000 -.002
PSC-330-WB 2 1/2 2 1/8 3/16 2.500 +.002 -.000 2.125 +.000 -.002 0.424 +.005 -.000 2.498 +.000 -.002
PSC-331 2 5/8 2 1/4 3/16 2.625 +.002 -.000 2.250 +.000 -.002 0.280 +.005 -.000 2.622 +.000 -.002
PSC-332 2 3/4 2 3/8 3/16 2.749 +.004 -.000 2.374 +.000 -.004 0.280 +.005 -.000 2.747 +.000 -.004
PSC-332-WB 2 3/4 2 3/8 3/16 2.749 +.004 -.000 2.374 +.000 -.004 0.424 +.005 -.000 2.747 +.000 -.004
PSC-333 2 7/8 2 1/2 3/16 2.874 +.004 -.000 2.499 +.000 -.004 0.280 +.005 -.000 2.872 +.000 -.004
PSC-334 3 2 5/8 3/16 2.999 +.004 -.000 2.624 +.000 -.004 0.280 +.005 -.000 2.997 +.000 -.004
PSC-334-WB 3 2 5/8 3/16 2.999 +.004 -.000 2.624 +.000 -.004 0.424 +.005 -.000 2.997 +.000 -.004
PSC-335 3 1/8 2 3/4 3/16 3.124 +.004 -.000 2.749 +.000 -.004 0.280 +.005 -.000 3.122 +.000 -.004
PSC-335-F 3 1/8 2 3/4 3/16 3.124 +.004 -.000 2.749 +.000 -.004 0.250 +.005 -.000 3.122 +.000 -.004
PSC-336 3 1/4 2 7/8 3/16 3.249 +.004 -.000 2.874 +.000 -.004 0.280 +.005 -.000 3.247 +.000 -.004
PSC-337 3 3/8 3 3/16 3.375 +.004 -.000 3.000 +.000 -.004 0.280 +.005 -.000 3.373 +.000 -.004
PSC-338 3 1/2 3 1/8 3/16 3.500 +.004 -.000 3.125 +.000 -.004 0.280 +.005 -.000 3.498 +.000 -.004
PSC-338-WB 3 1/2 3 1/8 3/16 3.500 +.004 -.000 3.125 +.000 -.004 0.424 +.005 -.000 3.498 +.000 -.004
PSC-339 3 5/8 3 1/4 3/16 3.625 +.004 -.000 3.250 +.000 -.004 0.280 +.005 -.000 3.623 +.000 -.004
PSC-340 3 3/4 3 3/8 3/16 3.752 +.004 -.000 3.375 +.000 -.004 0.280 +.005 -.000 3.748 +.000 -.004
PSC-341 3 7/8 3 1/2 3/16 3.875 +.004 -.000 3.500 +.000 -.004 0.280 +.005 -.000 3.873 +.000 -.004
PSC-342 4 3 5/8 3/16 4.000 +.004 -.000 3.625 +.000 -.004 0.280 +.005 -.000 3.998 +.000 -.004
PSC-342-WB 4 3 5/8 3/16 4.000 +.004 -.000 3.625 +.000 -.004 0.424 +.005 -.000 3.998 +.000 -.004
PSC-343 4 1/8 3 3/4 3/16 4.125 +.004 -.000 3.750 +.000 -.004 0.280 +.005 -.000 4.123 +.000 -.004
PSC-344 4 1/4 3 7/8 3/16 4.250 +.004 -.000 3.875 +.000 -.004 0.280 +.005 -.000 4.248 +.000 -.004
PSC-345 4 3/8 4 3/16 4.375 +.004 -.000 4.000 +.000 -.004 0.280 +.005 -.000 4.373 +.000 -.004
PSC-346 4 1/2 4 1/8 3/16 4.500 +.004 -.000 4.125 +.000 -.004 0.280 +.005 -.000 4.498 +.000 -.004
PSC-347 4 5/8 4 1/4 3/16 4.625 +.004 -.000 4.250 +.000 -.004 0.280 +.005 -.000 4.623 +.000 -.004
PSC-348 4 3/4 4 3/8 3/16 4.750 +.004 -.000 4.375 +.000 -.004 0.280 +.005 -.000 4.748 +.000 -.004
PSC-349 4 7/8 4 1/2 3/16 4.875 +.004 -.000 4.500 +.000 -.004 0.280 +.005 -.000 4.873 +.000 -.004
PSC-350 5 4 5/8 3/16 5.001 +.004 -.000 4.626 +.000 -.004 0.280 +.006 -.000 4.999 +.000 -.004
New parts are always being added. Call for sizes not shown and seal kits.
332
Inch
Piston Seals
PSC-426 5 1/8 4 5/8 1/4 5.125 +.004 -.000 4.646 +.000 -.004 0.365 +.006 -.000 5.124 +.000 -.004
PSC-427 5 1/4 4 3/4 1/4 5.251 +.004 -.000 4.770 +.000 -.004 0.365 +.006 -.000 5.249 +.000 -.004
PSC-428 5 3/8 4 7/8 1/4 5.376 +.004 -.000 4.896 +.000 -.004 0.365 +.006 -.000 5.374 +.000 -.004
PSC-429 5 1/2 5 1/4 5.501 +.004 -.000 5.021 +.000 -.004 0.365 +.006 -.000 4.499 +.000 -.004
PSC-430 5 5/8 5 1/8 1/4 5.626 +.004 -.000 5.146 +.000 -.004 0.365 +.006 -.000 5.624 +.000 -.004
PSC-431 5 3/4 5 1/4 1/4 5.751 +.004 -.000 5.271 +.000 -.004 0.365 +.006 -.000 5.749 +.000 -.004
PSC-432 5 7/8 5 3/8 1/4 5.876 +.004 -.000 5.396 +.000 -.004 0.365 +.006 -.000 5.874 +.000 -.004
PSC-433 6 5 1/2 1/4 6.001 +.004 -.000 5.521 +.000 -.004 0.365 +.006 -.000 5.999 +.000 -.004
PSC-433-WB 6 5 1/2 1/4 6.001 +.004 -.000 5.521 +.000 -.004 0.579 +.006 -.000 5.999 +.000 -.004
PSC-434 6 1/8 5 5/8 1/4 6.126 +.004 -.000 5.646 +.000 -.004 0.365 +.006 -.000 6.124 +.000 -.004
PSC-435 6 1/4 5 3/4 1/4 6.251 +.004 -.000 5.771 +.000 -.004 0.365 +.006 -.000 6.249 +.000 -.004
PSC-437 6 1/2 6 1/4 6.500 +.006 -.000 6.020 +.000 -.006 0.365 +.006 -.000 6.498 +.000 -.006
PSC-438 6 3/4 6 1/4 1/4 6.750 +.006 -.000 6.270 +.000 -.006 0.365 +.006 -.000 6.748 +.000 -.006
PSC-439 7 6 1/2 1/4 7.000 +.006 -.000 6.520 +.000 -.006 0.365 +.006 -.000 6.998 +.000 -.006
PSC-440 7 1/4 6 3/4 1/4 7.250 +.006 -.000 6.770 +.000 -.006 0.365 +.006 -.000 7.248 +.000 -.006
PSC-441 7 1/2 7 1/4 7.500 +.006 -.000 7.020 +.000 -.006 0.365 +.006 -.000 7.498 +.000 -.006
PSC-442 7 3/4 7 1/4 1/4 7.750 +.006 -.000 7.270 +.000 -.006 0.365 +.006 -.000 7.748 +.000 -.006
PSC-443 8 7 1/2 1/4 8.000 +.006 -.000 7.520 +.000 -.006 0.365 +.006 -.000 7.998 +.000 -.006
PSC-444 8 1/4 7 3/4 1/4 8.250 +.006 -.000 7.770 +.000 -.006 0.365 +.006 -.000 8.248 +.000 -.006
PSC-445 8 1/2 8 1/4 8.500 +.006 -.000 8.020 +.000 -.006 0.365 +.006 -.000 8.498 +.000 -.006
PSC-446 9 8 1/2 1/4 9.000 +.006 -.000 8.520 +.000 -.006 0.365 +.006 -.000 8.998 +.000 -.006
PSC-447 9 1/2 9 1/4 9.500 +.006 -.000 9.020 +.000 -.006 0.365 +.006 -.000 9.498 +.000 -.006
PSC-448 10 9 1/2 1/4 10.000 +.006 -.000 9.520 +.000 -.006 0.365 +.006 -.000 9.998 +.000 -.006
PSC-449 10 1/2 10 1/4 10.500 +.006 -.000 10.020 +.000 -.006 0.365 +.006 -.000 10.498 +.000 -.006
PSC-450 11 10 1/2 1/4 11.000 +.006 -.000 10.520 +.000 -.006 0.365 +.006 -.000 10.998 +.000 -.006
PSC-451 11 1/2 11 1/4 11.500 +.006 -.000 11.020 +.000 -.006 0.365 +.006 -.000 11.498 +.000 -.006
PSC-452 12 11 1/2 1/4 12.000 +.006 -.000 11.520 +.000 -.006 0.365 +.006 -.000 11.998 +.000 -.006
333
Inch
Piston Seals
Maximum extrusion gap Figures show the maximum permissible gap all OD ID
on one side using minimum clearance and
maximum bore .
Prefix OD
A compact double acting piston seal assembly designed for one piece pistons, suitable for low to high pressure, and medium to
heavy duty applications. The assembly is comprised of a standard self-lubricating wear resistant bronze filled or glass / MoS2
filled PTFE cap ring, which is loaded by a NBR energiser. The anti-extrusion rings support the seal on both sides and prevent
contamination of the energiser and cap ring. Used in a variety of equipment but particularly suited for use in earthmoving and other
off-highway equipment.
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
334
Inch
Piston Seals
335
Inch
Piston Seals
A double acting piston seal designed specifically for one piece pistons. Type 53 uses a rubber sealing
element which has proven itself to be extremely wear resistant and capable of working in a wide variety
of medium duty applications. The seal is also suitable for two piece pistons. The assembly comprises a
rubber seal, two split support rings and two split bearings, one of each located either side of the seal.
L1 L2
Part Number
Part Number OD
OD1 OD
Od11
OD
Od22
OD
Od33 L1+.016 L+.004
2
+.005 -0.0
53-2.00X1.375X.750X.250 2.000 +0.007 +0.000 1.375 +0.000 -0.004 1.820 +0.001 -0.004 1.950 +0.000 -0.007 0.750 0.250
53-2.00X1.625X.437X.156 2.000 +0.007 +0.000 1.625 +0.000 -0.004 1.821 +0.001 -0.004 1.936 +0.000 -0.007 0.437 0.156
53-2.250X1.625X.750X.250 2.250 +0.007 +0.000 1.625 +0.000 -0.004 2.071 +0.001 -0.004 2.200 +0.000 -0.007 0.750 0.250
53-2.375X1.75X.750X.250 2.375 +0.007 +0.000 1.750 +0.000 -0.004 2.193 +0.001 -0.004 2.322 +0.000 -0.007 0.750 0.250
53-2.50X1.875X.750X.250 2.500 +0.007 +0.000 1.875 +0.000 -0.004 2.321 +0.001 -0.004 2.450 +0.000 -0.007 0.750 0.250
53-2.625X2.00X.750X.250 2.625 +0.007 +0.000 2.000 +0.000 -0.005 2.444 +0.001 -0.004 2.569 +0.000 -0.007 0.750 0.250
53-2.750X2.00X.937X.250 2.750 +0.007 +0.000 2.000 +0.000 -0.005 2.524 +0.001 -0.004 2.690 +0.000 -0.007 0.937 0.250
53-3.00X2.250X.937X.250 3.000 +0.007 +0.000 2.250 +0.000 -0.005 2.774 +0.001 -0.004 2.940 +0.000 -0.007 0.937 0.250
53-3.00X2.375X.763X.241 3.000 +0.007 +0.000 2.375 +0.000 -0.005 2.793 +0.001 -0.004 2.919 +0.000 -0.007 0.763 0.241
53-3.50X2.75X.937X.250 3.500 +0.009 +0.000 2.750 +0.000 -0.005 3.274 +0.001 -0.005 3.440 +0.000 -0.009 0.937 0.250
53-4.00X3.250X.937X.250 4.000 +0.009 +0.000 3.250 +0.000 -0.006 3.773 +0.001 -0.005 3.940 +0.000 -0.009 0.937 0.250
53-4.00X3.25X.937X.250-H 4.000 +0.009 +0.000 3.250 +0.000 -0.006 3.773 +0.001 -0.005 3.940 +0.000 -0.009 0.937 0.250
53-4.00X3.250X1.375X.375 4.000 +0.009 +0.000 3.250 +0.000 -0.006 3.770 +0.001 -0.005 3.939 +0.000 -0.009 1.375 0.375
53-4.00X3.37X.775X.250 4.000 +0.009 +0.000 3.370 +0.000 -0.006 3.770 +0.001 -0.005 3.959 +0.000 -0.009 0.775 0.250
53-5.00X4.00X1.250X.375 5.000 +0.010 +0.000 4.000 +0.000 -0.006 4.712 +0.001 -0.005 4.910 +0.000 -0.000 1.250 0.375
53-6.00X5.00X1.25X.375 6.000 +0.010 +0.000 5.000 +0.000 -0.006 5.713 +0.002 -0.006 5.910 +0.000 -0.000 1.250 0.375
New parts are always being added. Call for sizes not shown and seal kits.
336
Inch
Piston Seals
Od1 OD1
Grizzly Supplies Part Numbers: Od3 Od2
58 - 1.750 X 1.125 X .937 X .250
A three piece double acting piston seal. Incorporating a nitrile and fabric seal with two bearings. This
makes it capable of using larger clearances and, with the integral bearing rings, to restrict the piston
length. This is a heavy duty seal assembly for split pistons.
L1 L2
Part Number
Part Number OD OD1 OD1 Od1 OD2Od2 ODOd
3 3
L+.035
1
L 2
+0.0
+.025 -.005
58-1.750X1.125X.937X.250 1.750 +.006 +.000 1.125 +.003 -0.003 1.555 +.000 -.002 1.687 +.000 -.003 0.937 0.250
58-2.00X1.375X.750X.250 2.000 +.007 +.000 1.375 +.003 -0.003 1.805 +.000 -.002 1.937 +.000 -.004 0.750 0.250
58-2.00X1.375X.937X.250 2.000 +.007 +.000 1.375 +.003 -0.003 1.822 +.000 -.002 1.962 +.000 -.004 0.937 0.250
58-2.125X1.50X.937X.250 2.125 +.007 +.000 1.500 +.003 -0.003 1.928 +.000 -.002 2.062 +.000 -.004 0.937 0.250
58-2.25X1.625X.750X.250 2.250 +.007 +.000 1.625 +.003 -0.003 2.055 +.000 -.003 2.187 +.000 -.004 0.750 0.250
58-2.25X1.625X.937X.250 2.250 +.007 +.000 1.625 +.003 -0.003 2.071 +.000 -.003 2.211 +.000 -.004 0.937 0.250
58-2.500X1.875X.750X.250 2.500 +.007 +.000 1.875 +.003 -0.003 2.305 +.000 -.003 2.437 +.000 -.004 0.750 0.250
58-2.500X1.875X.937X.250 2.500 +.007 +.000 1.875 +.003 -0.003 2.321 +.000 -.003 2.460 +.000 -.004 0.937 0.250
58-2.625X2.00X.937X.250 2.625 +.007 +.000 2.000 +.003 -0.003 2.428 +.000 -.003 2.562 +.000 -.004 0.937 0.250
58-2.75X2.00X.937X.250 2.750 +.007 +.000 2.000 +.003 -0.003 2.485 +.000 -.003 2.687 +.000 -.004 0.937 0.250
58-2.75X2.00X1.187X.250 2.750 +.007 +.000 2.000 +.003 -0.003 2.524 +.000 -.003 2.710 +.000 -.004 1.187 0.250
58-2.875X2.125X1.187X.250 2.875 +.007 +.000 2.125 +.003 -0.003 2.610 +.000 -.003 2.812 +.000 -.004 1.187 0.250
58-3.00X2.250X.937X.250 3.000 +.007 +.000 2.250 +.003 -0.003 2.735 +.000 -.003 2.937 +.000 -.004 0.937 0.250
58-3.00X2.250X1.187X.250 3.000 +.007 +.000 2.250 +.003 -0.003 2.774 +.000 -.003 2.960 +.000 -.004 1.187 0.250
58-3.250X2.500X1.187X.250 3.250 +.009 +.000 2.500 +.004 -0.004 2.985 +.000 -.003 3.187 +.000 -.004 1.187 0.250
58-3.500X2.750X.937X.254 3.500 +.009 +.000 2.750 +.004 -0.004 3.273 +.000 -.003 3.460 +.000 -.004 0.937 0.254
58-3.50X2.750X1.187X.250 3.500 +.009 +.000 2.750 +.004 -0.004 3.235 +.000 -.003 3.437 +.000 -.004 1.187 0.250
58-3.75X3.00X1.187X.250 3.750 +.009 +.000 3.000 +.004 -0.004 3.485 +.000 -.003 3.687 +.000 -.004 1.187 0.250
337
Inch
Piston Seals
58-4.00X3.250X.937X.250 4.000 +.009 +.000 3.250 +.004 -0.004 3.772 +.000 -.003 3.958 +.000 -.004 0.937 0.250
58-4.00X3.250X1.187X.250 4.000 +.009 +.000 3.250 +.004 -0.004 3.735 +.000 -.003 3.937 +.000 -.004 1.187 0.250
58-4.50X3.500X1.500X.375 4.500 +.009 +.000 3.500 +.004 -0.004 4.234 +.000 -.003 4.437 +.000 -.004 1.500 0.375
58-4.750X3.750X1.250X.254 4.750 +.010 +.000 3.750 +.004 -0.004 4.483 +.000 -.003 4.700 +.000 -.005 1.250 0.254
58-4.750X3.750X1.500X.375 4.750 +.010 +.000 3.750 +.004 -0.004 4.485 +.000 -.003 4.687 +.000 -.005 1.500 0.375
58-5.00X4.00X1.250X.254 5.000 +.010 +.000 4.000 +.005 -0.005 4.730 +.000 -.004 4.956 +.000 -.005 1.250 0.254
58-5.00X4.00X1.500X.375 5.000 +.010 +.000 4.000 +.005 -0.005 4.735 +.000 -.004 4.937 +.000 -.005 1.500 0.375
58-5.250X4.250X1.500X.375 5.250 +.010 +.000 4.250 +.005 -0.005 4.980 +.000 -.004 5.187 +.000 -.005 1.500 0.375
58-5.50X4.500X1.500X.375 5.500 +.010 +.000 4.500 +.005 -0.005 5.236 +.000 -.004 5.437 +.000 -.005 1.500 0.375
58-5.750X4.750X1.500X.375 5.750 +.010 +.000 4.750 +.005 -0.005 5.484 +.000 -.004 5.687 +.000 -.005 1.500 0.375
58-6.00X5.00X1.250X.254 6.000 +.010 +.000 5.000 +.005 -0.005 5.728 +.000 -.004 5.954 +.000 -.005 1.250 0.254
58-6.00X5.00X1.500X.375 6.000 +.010 +.000 5.000 +.005 -0.005 5.736 +.000 -.004 5.937 +.000 -.005 1.500 0.375
58-6.50X5.500X1.500X.375 6.500 +.010 +.000 5.500 +.005 -0.005 6.236 +.000 -.004 6.437 +.000 -.005 1.500 0.375
58-7.00X6.00X1.500X.375 7.000 +.010 +.000 6.000 +.005 -0.005 6.736 +.000 -.004 6.937 +.000 -.005 1.500 0.375
58-7.500X6.250X1.875X.375 7.500 +.010 +.000 6.250 +.005 -0.005 7.240 +.000 -.004 7.437 +.000 -.006 1.875 0.375
58-8.00X7.00X1.250X.375 8.000 +.011 +.000 7.000 +.006 -0.006 7.740 +.000 -.005 7.937 +.000 -.006 1.250 0.375
58-9.00X8.00X1.250X.375 9.000 +.011 +.000 8.000 +.006 -0.006 8.736 +.000 -.005 8.937 +.000 -.006 1.250 0.375
58-10.00X9.00X1.250X.375 10.000 +.013 +.000 9.000 +.006 -0.006 9.740 +.000 -.005 9.937 +.000 -.006 1.250 0.375
New parts are always being added. Call for sizes not shown and seal kits.
338
Inch
Piston Seals
65 Delta Seal
L2 L2 C
Operating conditions L1
Temperature: -22 to 212 F (-30 to 100 C)
20~30
Max. Speed: 0.5 m/s (1.5 ft/sec) r2
Max. Pressure: 200 bar (3000 p.s.i.) r1 S
Breakcorner
0.25mm (0.010)
Od3 Od2 max rad. Od1 OD1
Grizzly Supplies Part Numbers:
65 - 1.250 X .937 X .343 X .125
Ideal for light to medium duty and for one piece piston applications. Its compact dimensions make it
capable of keeping the length of the piston to a minimum. It is an assembly consisting of a continuous
rubber seal and two scarf cut bearings. The nitrile rubber seal is designed to be pre-loaded into the
housing and will ensure an effective seal at low pressure. During increasing pressure, the outward thrust
of the rubber seal on the bearings prevents any extrusion damage to the sealing area.
L1 L2
Part Number OD1 Od1 Od2 Od3 +.015 +0.0
+.005 -.005
65-1.250X.937X.343X.125 1.250 +.004 +.000 0.937 +.000 -.002 1.079 +.000 -.002 1.187 +.000 -.005 0.343 0.125
65-1.500X1.125X.437X.150 1.500 +.004 +.000 1.125 +.000 -.002 1.324 +.000 -.002 1.437 +.000 -.006 0.437 0.150
65-1.750X1.375X.437X.150 1.750 +.004 +.000 1.375 +.000 -.002 1.574 +.000 -.002 1.687 +.000 -.006 0.437 0.150
65-2.250X1.875X.437X.150 2.250 +.005 +.000 1.875 +.000 -.003 2.075 +.000 -.003 2.187 +.000 -.007 0.437 0.150
65-2.750X2.375X.437X.150 2.750 +.005 +.000 2.375 +.000 -.003 2.575 +.000 -.003 2.437 +.000 -.007 0.437 0.150
65-3.00X2.625X.437X.150 3.000 +.005 +.000 2.625 +.000 -.003 2.825 +.000 -.003 2.937 +.000 -.007 0.437 0.150
65-3.250X2.875X.437X.150 3.250 +.006 +.000 2.875 +.000 -.003 3.075 +.000 -.003 3.187 +.000 -.009 0.437 0.150
65-3.500X3.00X.562X.210 3.500 +.006 +.000 3.000 +.000 -.003 3.270 +.000 -.003 3.437 +.000 -.009 0.562 0.210
65-3.750X3.250X.562X.210 3.750 +.006 +.000 3.250 +.000 -.003 3.520 +.000 -.003 3.687 +.000 -.009 0.562 0.210
65-4.00X3.500X.562X.210 4.000 +.006 +.000 3.500 +.000 -.003 3.770 +.000 -.003 3.937 +.000 -.009 0.562 0.210
65-4.50X4.00X.562X.210 4.500 +.006 +.000 4.000 +.000 -.003 4.270 +.000 -.003 4.187 +.000 -.009 0.562 0.210
65-5.00X4.375X.687X.344 5.000 +.006 +.000 4.375 +.000 -.003 4.689 +.000 -.003 4.937 +.000 -.010 0.687 0.344
65-5.50X4.875X.687X.344 5.500 +.006 +.000 4.875 +.000 -.004 5.188 +.000 -.004 5.437 +.000 -.010 0.687 0.344
339
Inch
Piston Seals
TP Piston T Seal
Cross
Temperature: -35 to 265 F (-37 to 129 C) Section
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
340
Inch
Piston Seals
TP Piston T Seal
Groove Groove
Part Number OD
Diameter Height
341
Inch
Piston Seals
TP Piston T Seal
Groove Groove
Part Number OD
Diameter Height
342
Inch
Piston Seals
TP Piston T Seal
Groove Groove
Part Number OD
Diameter Height
343
Inch
Piston Seals
Height
Cross Section
Neo-fab piston cups used in hydraulic applications. These come solid or with a custom cut centre hole.
-L is leather cup.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
344
Inch
Piston Seals
NF-5250-500
NF-5250-750
NF-5500-750
NF-5750-750
NF-6000-625
NF-6000-750
NF-6500-750
NF-7000-750
NF-7250-750
NF-7500-1000
NF-8000-750
NF-8000-1000
NF-8500-1000
NF-9000-1000
NF-9500-1000
NF-10000-750
NF-10000-1000
NF-11000-1250
NF-11500-1000-187
NF-12000-1000-187
NF-12000-1250
345
Inch
Piston Seals
Prefix OD Height
Height
Cross Section
Rubber piston cups used for pneumatic cylinder applications. These come solid or with a custom cut
centre hole.
Part Number
RPC-1250-375 RPC-4750-625
RPC-1250-437 RPC-5750-750
RPC-1250-500 RPC-6000-750
RPC-1500-500 RPC-8000-1000
RPC-1750-500 RPC-9500-1000
RPC-2000-500 RPC-10000-1000
RPC-2125-500 RPC-11500-1000
RPC-2250-500 RPC-14000-1000
RPC-2375-500
RPC-2500-500
RPC-2625-500
RPC-2750-500
RPC-3000-500
RPC-3500-625
RPC-3750-625
RPC-3875-625
RPC-4000-625
RPC-4500-625
New parts are always being added. Call for sizes not shown and seal kits.
346
Inch
Piston Seals
25
Height
Cross Section
Part Number
NOPAK-1.50
NOPAK-3.00
NOPAK-4.00
NOPAK-5.00
NOPAK-6.00
NOPAK-8.00
NOPAK-10.00
347
Inch
Piston Seals
ID OD
25
Part Number OD
DEL-4 2.000
DEL-5 2.625
DEL-7 3.250
DEL-13 3.875
DEL-15 4.750
DEL-23/1 5.750
New parts are always being added. Call for sizes not shown and seal kits.
348
Inch
Piston Seals
When using cast iron piston rings, it is crucial to use the correct groove design
for proper performance of the cylinder. Please use the following guidelines when
cutting a cast iron piston ring groove.
Groove Width: To permit the ring to slide freely into the groove, the groove
must be at least 0.001 inches wider than the maximum piston ring width with a 25
tolerance of +0.003/-0 inches.
Groove Depth: Grooves must be at least 0.015 inches deeper than the
maximum radial wall thickness of the piston ring with a tolerance of +0.003/-0
inches. This is to avoid any possibility of the ring bottoming in the groove when
the ring is compressed to its working diameter.
Radial Clearance: The radial clearance between the cylinder bore and piston
should be less than 1/3 of the radial wall thickness of the piston ring to ensure
sealing effectiveness.
Part Number
349
Inch
Piston Seals
350
Inch
Piston Seals
PIP Ring
Prefix OD Height
ID
OD
PIP rings are used in a piston application along with a B-lip polypack. When used together, they become
a double acting seal.
351
Inch
Piston Seals
PIP Ring
Part Number ID OD Part Number ID OD
352
Inch
Piston Seals
Additional Profiles
18
56
57
62
71
83
RJS
353
Metric
Wipers
Metric
Wipers
Inch
Wear Rings
New parts are always being added. Call for sizes not shown and seal kits.
354
Metric
Wipers
355
Inch
Wear Rings
WR Wear Ring
Operating conditions
Temperature: -40 to 250 F (-40 to 120 C)
Max. Speed: 5.0 m/s (15.0 ft/sec) OD
Speed: 12 ft/sec
Height
OD
ID
Height
Made from glass filled nylon. These wear rings are designed for reciprocating piston and rod bearing
applications.
Part Number
New parts are always being added. Call for sizes not shown and seal kits.
356
Inch
Wear Rings
WR Wear Ring
Part Number
357
Inch
Wear Rings
WR Wear Ring
Part Number
358
Inch
Wear Rings
WR Wear Ring
Part Number
359
Inch
Wear Rings
WR Wear Ring
Part Number
360
Inch
Wear Rings
WR Wear Ring
Part Number
361
Inch
Wear Rings
The T design allows full bearing contact, also offering the advantage of a t-groove form of retention that
does not require side land near the working surface of the wear band.
Part Number
WRT-1625-442-165
WRT-2750-567-160
WRT-3000-570-150
WRT-3500-750-125
WRT-4500-750-125
WRT-5500-750-125
WRT-6000-625-150
WRT-6500-750-125
WRT-7500-750-125
WRT-8500-750-125
WRT-9750-750-125
New parts are always being added. Call for sizes not shown and seal kits.
362
Inch
Wear Rings
Manufactured to a variety of widths and thicknesses. PTFE affords low friction capabilities with low
compressive strength. The material also has the capability of capturing metal particles and keeping them
from the seal area.
Part Number
TWRS-.375X.062
TWRS-.375X.125
TWRS-.500X.062
TWRS-.500X.125
TWRS-.625X.125
TWRS-.750X.125
TWRS-1.00X.125
TWRS-1.25X.125
TWRS-1.500X.125
363
Inch
Wear Rings
Operating conditions
Temperature: -40 to 250 F (-40 to 120 C) Height
Max. Speed: 0.1, 1.0, 5.0 m/s (0.3, 3.0, 16.0 ft/sec)
Max. Pressure: 10.0, 6.0, 0.8 MN/m2 (1500, 900, 120 p.s.i.)
Extremely effective, hard wearing and easy to use bearing material. Manufactured to very strict tolerances
and provides bearing solutions for reciprocating, oscillating and slow rotary movement applications.
Capable of withstanding extreme side-loads and preventing metal to metal contact. The materials design
incorporates micro indentations on the bearing strips surface to trap fluid and provide built-in lubrication
to the bearing.
Part Number
WRS-.375X.062
WRS-.500X.125
WRS-.625X.125
WRS-.750X.125
WRS-1.00X.125
WRS-1.500X.125
New parts are always being added. Call for sizes not shown and seal kits.
364
Notes
365
Metric
Wipers
Metric
Wipers
Inch
O-rings
New parts are always being added. Call for sizes not shown and seal kits.
366
Metric
Wipers
367
Inch
O-Rings
Inch O-ring
Call for availability on Quad rings and square cut
O-rings.
2-001 N70 -001 1/32 3/32 1/32 0.029 0.004 0.040 0.003 0.000 0.740 0.100 1.020 0.080
2-001 1/2 N70 -001 1/2 1/16 1/8 1/32 0.062 0.004 0.040 0.003 0.000 1.570 0.100 1.020 0.080
2-002 N70 -002 3/64 9/64 3/64 0.042 0.004 0.050 0.003 0.001 1.070 0.100 1.270 0.080
2-003 N70 -003 1/16 3/16 1/16 0.056 0.004 0.060 0.003 0.001 1.420 0.100 1.520 0.080
2-004 N70 -004 5/64 13/64 1/16 0.070 0.005 0.070 0.003 0.002 1.780 0.130 1.780 0.080
2-005 N70 -005 3/32 7/32 1/16 0.101 0.005 0.070 0.003 0.002 2.570 0.130 1.780 0.080
2-006 N70 -006 1/8 1/4 1/16 0.114 0.005 0.070 0.003 0.003 2.900 0.130 1.780 0.080
2-007 N70 -007 5/32 9/32 1/16 0.145 0.005 0.070 0.003 0.003 3.680 0.130 1.780 0.080
2-008 N70 -008 3/16 5/16 1/16 0.176 0.005 0.070 0.003 0.003 4.470 0.130 1.780 0.080
2-009 N70 -009 7/32 11/32 1/16 0.208 0.005 0.070 0.003 0.004 5.280 0.130 1.780 0.080
2-010 N70 -010 1/4 3/8 1/16 0.239 0.005 0.070 0.003 0.004 6.070 0.130 1.780 0.080
2-011 N70 -011 5/16 7/16 1/16 0.301 0.005 0.070 0.003 0.005 7.650 0.130 1.780 0.080
2-012 N70 -012 3/8 1/2 1/16 0.364 0.005 0.070 0.003 5.000 9.250 0.130 1.780 0.080
2-013 N70 -013 7/16 9/16 1/16 0.426 0.005 0.070 0.003 6.000 10.820 0.130 1.780 0.080
2-014 N70 -014 1/2 5/8 1/16 0.489 0.005 0.070 0.003 7.000 12.420 0.130 1.780 0.080
2-015 N70 -015 9/16 11/16 1/16 0.551 0.007 0.070 0.003 8.000 14.000 0.180 1.780 0.080
2-016 N70 -016 5/8 3/4 1/16 0.614 0.009 0.070 0.003 8.000 15.600 0.230 1.780 0.080
2-017 N70 -017 11/16 13/16 1/16 0.676 0.009 0.070 0.003 9.000 17.170 0.230 1.780 0.080
New parts are always being added. Call for sizes not shown and seal kits.
368
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-018 N70 -018 3/4 7/8 1/16 0.739 0.009 0.070 0.003 0.010 18.770 0.230 1.780 0.080
2-019 N70 -019 13/16 15/16 1/16 0.801 0.009 0.070 0.003 0.011 20.350 0.230 1.780 0.080
2-020 N70 -020 7/8 1 1/16 0.864 0.009 0.070 0.003 0.011 21.950 0.230 1.780 0.080
2-021 N70 -021 15/16 1 1/16 1/16 0.926 0.009 0.070 0.003 0.012 23.520 0.230 1.780 0.080
2-022 N70 -022 1 1 1/8 1/16 0.989 0.010 0.070 0.003 0.013 25.120 0.250 1.780 0.080
2-023 N70 -023 1 1/16 1 3/16 1/16 1.051 0.010 0.070 0.003 0.014 26.700 0.250 1.780 0.080
2-024 N70 -024 1 1/8 1 1/4 1/16 1.114 0.010 0.070 0.003 0.014 28.300 0.250 1.780 0.080
2-025 N70 -025 1 3/16 1 5/16 1/16 1.176 0.011 0.070 0.003 0.015 29.870 0.280 1.780 0.080
2-026 N70 -026 1 1/4 1 3/8 1/16 1.239 0.011 0.070 0.003 0.160 31.470 0.280 1.780 0.080
2-027 N70 -027 1 5/16 1 7/16 1/16 1.301 0.011 0.070 0.003 0.017 33.050 0.280 1.780 0.080
2-028 N70 -028 1 3/8 1 1/2 1/16 1.364 0.013 0.070 0.003 0.017 34.650 0.330 1.780 0.080
2-029 N70 -029 1 1/2 1 5/8 1/16 1.489 0.013 0.070 0.003 0.019 37.820 0.330 1.780 0.080
2-030 N70 -030 1 5/8 1 3/4 1/16 1.614 0.013 0.070 0.003 0.020 41.000 0.330 1.780 0.080
2-031 N70 -031 1 3/4 1 7/8 1/16 1.739 0.015 0.070 0.003 0.022 44.170 0.380 1.780 0.080
2-032 N70 -032 1 7/8 2 1/16 1.864 0.015 0.070 0.003 0.023 47.350 0.380 1.780 0.080
2-033 N70 -033 2 2 1/8 1/16 1.989 0.018 0.070 0.003 0.025 50.520 0.460 1.780 0.080
2-034 N70 -034 2 1/8 2 1/4 1/16 2.114 0.018 0.070 0.003 0.026 53.700 0.460 1.780 0.080
2-035 N70 -035 2 1/4 2 3/8 1/16 2.239 0.018 0.070 0.003 0.028 56.870 0.460 1.780 0.080
2-036 N70 -036 2 3/8 2 1/2 1/16 2.364 0.018 0.070 0.003 0.029 60.050 0.460 1.780 0.080
2-037 N70 -037 2 1/2 2 5/8 1/16 2.489 0.018 0.070 0.003 0.031 63.220 0.460 1.780 0.080
2-038 N70 -038 2 5/8 2 3/4 1/16 2.614 0.020 0.070 0.003 0.032 66.400 0.510 1.780 0.080
2-039 N70 -039 2 3/4 2 7/8 1/16 2.739 0.020 0.070 0.003 0.034 69.570 0.510 1.780 0.080
2-040 N70 -040 2 7/8 3 1/16 2.864 0.020 0.070 0.003 0.036 72.750 0.510 1.780 0.080
2-041 N70 -041 3 3 1/8 1/16 2.989 0.024 0.070 0.003 0.037 75.920 0.610 1.780 0.080
2-042 N70 -042 3 1/4 3 3/8 1/16 3.239 0.024 0.070 0.003 0.040 82.270 0.610 1.780 0.080
2-043 N70 -043 3 1/2 3 5/8 1/16 3.489 0.024 0.070 0.003 0.043 88.620 0.610 1.780 0.080
2-044 N70 -044 3 3/4 3 7/8 1/16 3.739 0.027 0.070 0.003 0.046 94.970 0.690 1.780 0.080
2-045 N70 -045 4 4 1/8 1/16 3.989 0.027 0.070 0.003 0.049 101.320 0.690 1.780 0.080
2-046 N70 -046 4 1/4 4 3/8 1/16 4.239 0.030 0.070 0.003 0.052 107.670 0.760 1.780 0.080
2-047 N70 -047 4 1/2 4 5/8 1/16 4.489 0.030 0.070 0.003 0.550 114.020 0.760 1.780 0.080
2-048 N70 -048 4 3/4 4 7/8 1/16 4.739 0.030 0.070 0.003 0.058 120.370 0.760 1.780 0.080
2-049 N70 -049 5 5 1/8 1/16 4.989 0.037 0.070 0.003 0.061 126.720 0.940 1.780 0.080
2-050 N70 -050 5 1/4 5 3/8 1/16 5.239 0.037 0.070 0.003 0.064 133.070 0.940 1.780 0.080
2-102 N70 -102 1/16 1/4 3/32 0.049 0.005 0.103 0.003 0.004 1.240 0.130 2.620 0.080
369
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-103 N70 -103 3/32 9/32 3/32 0.081 0.005 0.103 0.003 0.005 2.060 0.130 2.620 0.080
2-104 N70 -104 1/8 5/16 3/32 0.112 0.005 0.103 0.003 0.006 2.840 0.130 2.620 0.080
2-105 N70 -105 5/32 11/32 3/32 0.143 0.005 0.103 0.003 0.006 3.630 0.130 2.620 0.080
2-106 N70 -106 3/16 3/8 3/32 0.174 0.005 0.103 0.003 0.007 4.420 0.130 2.620 0.080
2-107 N70 -107 7/32 13/32 3/32 0.206 0.005 0.103 0.003 0.008 5.230 0.130 2.620 0.080
2-108 N70 -108 1/4 7/16 3/32 0.237 0.005 0.103 0.003 0.009 6.020 0.130 2.620 0.080
2-109 N70 -109 5/16 1/2 3/32 0.299 0.005 0.103 0.003 0.011 7.590 0.130 2.620 0.080
2-110 N70 -110 3/8 9/16 3/32 0.362 0.005 0.103 0.003 0.012 9.190 0.130 2.620 0.080
2-111 N70 -111 7/16 5/8 3/32 0.424 0.005 0.103 0.003 0.014 10.770 0.130 2.620 0.080
2-112 N70 -112 1/2 11/16 3/32 0.487 0.005 0.103 0.003 0.015 12.370 0.130 2.620 0.080
2-113 N70 -113 9/16 3/4 3/32 0.549 0.007 0.103 0.003 0.017 13.940 0.180 2.620 0.080
2-114 N70 -114 5/8 13/16 3/32 0.612 0.009 0.103 0.003 0.019 15.540 0.230 2.620 0.080
2-115 N70 -115 11/16 7/8 3/32 0.674 0.009 0.103 0.003 0.020 17.120 0.230 2.620 0.080
2-116 N70 -116 3/4 7/8 3/32 0.737 0.009 0.103 0.003 0.022 18.720 0.230 2.620 0.080
2-117 N70 -117 13/16 1 3/32 0.799 0.010 0.103 0.003 0.024 20.290 0.250 2.620 0.080
2-118 N70 -118 7/8 1 1/16 3/32 0.862 0.010 0.103 0.003 0.025 21.890 0.250 2.620 0.080
2-119 N70 -119 15/16 1 1/8 3/32 0.924 0.010 0.103 0.003 0.027 23.470 0.250 2.620 0.080
2-120 N70 -120 1 1 3/16 3/32 0.987 0.010 0.103 0.003 0.029 25.070 0.250 2.620 0.080
2-121 N70 -121 1 1/16 1 1/4 3/32 1.049 0.010 0.103 0.003 0.030 26.640 0.250 2.620 0.080
2-122 N70 -122 1 1/8 1 5/16 3/32 1.112 0.010 0.103 0.003 0.032 28.240 0.250 2.620 0.080
2-123 N70 -123 1 3/16 1 3/8 3/32 1.174 0.012 0.103 0.003 0.033 29.820 0.300 2.620 0.080
2-124 N70 -124 1 1/4 1 7/16 3/32 1.237 0.012 0.103 0.003 0.035 31.420 0.300 2.620 0.080
2-125 N70 -125 1 5/16 1 1/2 3/32 1.299 0.012 0.103 0.003 0.037 32.990 0.300 2.620 0.080
2-126 N70 -126 1 3/8 1 9/16 3/32 1.362 0.012 0.103 0.003 0.038 34.590 0.300 2.620 0.080
2-127 N70 -127 1 7/16 1 5/8 3/32 1.424 0.012 0.103 0.003 0.040 36.170 0.300 2.620 0.080
2-128 N70 -128 1 1/2 1 11/16 3/32 1.487 0.012 0.103 0.003 0.042 37.770 0.300 2.620 0.080
2-129 N70 -129 1 9/16 1 3/4 3/32 1.549 0.015 0.103 0.003 0.043 39.340 0.380 2.620 0.080
2-130 N70 -130 1 5/8 1 13/16 3/32 1.612 0.015 0.103 0.003 0.045 40.940 0.380 2.620 0.080
2-131 N70 -131 1 11/16 1 7/8 3/32 1.674 0.015 0.103 0.003 0.047 42.520 0.380 2.620 0.080
2-132 N70 -132 1 3/4 1 15/16 3/32 1.737 0.015 0.103 0.003 0.048 44.120 0.380 2.620 0.080
2-133 N70 -133 1 13/16 2 3/32 1.799 0.015 0.103 0.003 0.050 45.690 0.380 2.620 0.080
2-134 N70 -134 1 7/8 2 1/16 3/32 1.862 0.015 0.103 0.003 0.051 47.290 0.380 2.620 0.080
2-135 N70 -135 1 15/16 2 1/8 3/32 1.925 0.017 0.103 0.003 0.053 48.900 0.430 2.620 0.080
2-136 N70 -136 2 2 3/16 3/32 1.987 0.017 0.103 0.003 0.055 50.470 0.430 2.620 0.080
New parts are always being added. Call for sizes not shown and seal kits.
370
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-137 N70 -137 2 1/16 2 1/4 3/32 2.050 0.017 0.103 0.003 0.056 52.070 0.430 2.620 0.080
2-138 N70 -138 2 1/8 2 5/16 3/32 2.112 0.017 0.103 0.003 0.058 53.640 0.430 2.620 0.080
2-139 N70 -139 2 3/16 2 3/8 3/32 2.175 0.017 0.103 0.003 0.060 55.240 0.430 2.620 0.080
2-140 N70 -140 2 1/4 2 7/16 3/32 2.237 0.017 0.103 0.003 0.061 56.820 0.430 2.620 0.080
2-141 N70 -141 2 5/16 2 1/2 3/32 2.300 0.020 0.103 0.003 0.063 58.420 0.510 2.620 0.080
2-142 N70 -142 2 3/8 2 9/16 3/32 2.362 0.020 0.103 0.003 0.065 59.990 0.510 2.620 0.080
2-143 N70 -143 2 7/16 2 5/8 3/32 2.425 0.020 0.103 0.003 0.066 61.590 0.510 2.620 0.080
2-144 N70 -144 2 1/2 2 11/16 3/32 2.487 0.020 0.103 0.003 0.068 63.170 0.510 2.620 0.080
2-145 N70 -145 2 9/16 2 3/4 3/32 2.550 0.020 0.103 0.003 0.069 64.770 0.510 2.620 0.080
2-146 N70 -146 2 5/8 2 13/16 3/32 2.612 0.020 0.103 0.003 0.071 66.340 0.510 2.620 0.080
2-147 N70 -147 2 11/16 2 7/8 3/32 2.675 0.020 0.103 0.003 0.073 67.950 0.510 2.620 0.080
2-148 N70 -148 2 3/4 2 15/16 3/32 2.737 0.022 0.103 0.003 0.074 69.520 0.560 2.620 0.080
2-149 N70 -149 2 13/16 3 3/32 2.800 0.022 0.103 0.003 0.076 71.120 0.560 2.620 0.080
2-150 N70 -150 2 7/8 3 1/16 3/32 2.862 0.022 0.103 0.003 0.078 72.690 0.560 2.620 0.080
2-151 N70 -151 3 3 3/16 3/32 2.987 0.024 0.103 0.003 0.081 75.870 0.610 2.620 0.080
2-152 N70 -152 3 1/4 3 7/16 3/32 3.237 0.024 0.103 0.003 0.087 82.220 0.610 2.620 0.080
2-153 N70 -153 3 1/2 3 11/16 3/32 3.487 0.024 0.103 0.003 0.094 88.570 0.610 2.620 0.080
2-154 N70 -154 3 3/4 3 15/16 3/32 3.737 0.028 0.103 0.003 0.101 94.920 0.710 2.620 0.080
2-155 N70 -155 4 4 3/16 3/32 3.987 0.028 0.103 0.003 0.107 101.270 0.710 2.620 0.080
2-156 N70 -156 4 1/4 4 7/16 3/32 4.237 0.030 0.103 0.003 0.114 107.620 0.760 2.620 0.080
2-157 N70 -157 4 1/4 4 11/16 3/32 4.487 0.030 0.103 0.003 0.120 113.970 0.760 2.620 0.080
2-158 N70 -158 4 1/2 4 15/16 3/32 4.737 0.030 0.103 0.003 0.127 120.320 0.760 2.620 0.080
2-159 N70 -159 4 3/4 5 3/16 3/32 4.987 0.035 0.103 0.003 0.133 126.670 0.890 2.620 0.080
2-160 N70 -160 5 5 7/16 3/32 5.237 0.035 0.103 0.003 0.140 133.020 0.890 2.620 0.080
2-161 N70 -161 5 1/4 5 11/16 3/32 5.487 0.035 0.103 0.003 0.146 139.370 0.890 2.620 0.080
2-162 N70 -162 5 1/2 5 15/16 3/32 5.737 0.035 0.103 0.003 0.153 145.720 0.890 2.620 0.080
2-163 N70 -163 5 3/4 6 3/16 3/32 5.987 0.035 0.103 0.003 0.159 152.070 0.890 2.620 0.080
2-164 N70 -164 6 6 7/16 3/32 6.237 0.040 0.103 0.003 0.166 158.420 1.020 2.620 0.080
2-165 N70 -165 6 1/4 6 11/16 3/32 6.487 0.040 0.103 0.003 0.173 164.770 1.020 2.620 0.080
2-166 N70 -166 6 3/4 6 15/16 3/32 6.737 0.040 0.103 0.003 0.179 171.120 1.020 2.620 0.080
2-167 N70 -167 7 7 3/16 3/32 6.987 0.040 0.103 0.003 0.186 177.470 1.020 2.620 0.080
2-168 N70 -168 7 1/4 7 7/16 3/32 7.237 0.045 0.103 0.003 0.192 183.820 1.140 2.620 0.080
2-169 N70 -169 7 1/2 7 11/16 3/32 7.487 0.045 0.103 0.003 0.199 190.170 1.140 2.620 0.080
2-170 N70 -170 7 3/4 7 15/16 3/32 7.737 0.045 0.103 0.003 0.205 196.520 1.140 2.620 0.080
371
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-171 N70 -171 8 8 3/16 3/32 7.987 0.045 0.103 0.003 0.212 202.870 1.140 2.620 0.080
2-172 N70 -172 8 1/4 8 7/16 3/32 8.237 0.050 0.103 0.003 0.218 209.220 1.270 2.620 0.080
2-173 N70 -173 8 1/2 8 11/16 3/32 8.487 0.050 0.103 0.003 0.225 215.570 1.270 2.620 0.080
2-174 N70 -174 8 3/4 8 15/16 3/32 8.737 0.050 0.103 0.003 0.231 221.920 1.270 2.620 0.080
2-175 N70 -175 9 9 3/16 3/32 8.987 0.050 0.103 0.003 0.238 228.270 1.270 2.620 0.080
2-176 N70 -176 9 1/4 9 7/16 3/32 9.237 0.055 0.103 0.003 0.245 234.620 1.400 2.620 0.080
2-177 N70 -177 9 1/2 9 11/16 3/32 9.487 0.055 0.103 0.003 0.251 240.970 1.400 2.620 0.080
2-178 N70 -178 9 3/4 9 15/16 3/32 9.737 0.055 0.103 0.003 0.258 247.320 1.400 2.620 0.080
2-201 N70 -201 3/16 7/16 1/8 0.171 0.055 0.139 0.004 0.015 4.340 1.400 3.530 0.100
2-202 N70 -202 1/4 1/2 1/8 0.234 0.005 0.139 0.004 0.018 5.940 0.130 3.530 0.100
2-203 N70 -203 5/16 9/16 1/8 0.296 0.005 0.139 0.004 0.021 7.520 0.130 3.530 0.100
2-204 N70 -204 3/8 5/8 1/8 0.359 0.005 0.139 0.004 0.024 9.120 0.130 3.530 0.100
2-205 N70 -205 7/16 11/16 1/8 0.421 0.005 0.139 0.004 0.027 10.690 0.130 3.530 0.100
2-206 N70 -206 1/2 3/4 1/8 0.484 0.005 0.139 0.004 0.030 12.290 0.130 3.530 0.100
2-207 N70 -207 9/16 13/16 1/8 0.546 0.007 0.139 0.004 0.033 13.870 0.180 3.530 0.100
2-208 N70 -208 5/8 7/8 1/8 0.609 0.009 0.139 0.004 0.036 15.470 0.230 3.530 0.100
2-209 N70 -209 11/16 15/16 1/8 0.671 0.010 0.139 0.004 0.039 17.040 0.250 3.530 0.100
2-210 N70 -210 3/4 1 1/8 0.734 0.010 0.139 0.004 0.042 18.640 0.250 3.530 0.100
2-211 N70 -211 13/16 1 1/16 1/8 0.796 0.010 0.139 0.004 0.045 20.220 0.250 3.530 0.100
2-212 N70 -212 7/8 1 1/8 1/8 0.859 0.010 0.139 0.004 0.048 21.820 0.250 3.530 0.100
2-213 N70 -213 15/16 1 3/16 1/8 0.921 0.010 0.139 0.004 0.051 23.390 0.250 3.530 0.100
2-214 N70 -214 1 1 1/4 1/8 0.984 0.010 0.139 0.004 0.054 25.000 0.250 3.530 0.100
2-215 N70 -215 1 1/16 1 5/16 1/8 1.046 0.010 0.139 0.004 0.057 26.570 0.250 3.530 0.100
2-216 N70 -216 1 1/8 1 3/8 1/8 1.109 0.012 0.139 0.004 0.060 28.170 0.300 3.530 0.100
2-217 N70 -217 1 3/16 1 7/16 1/8 1.171 0.012 0.139 0.004 0.062 29.740 0.300 3.530 0.100
2-218 N70 -218 1 1/4 1 1/2 1/8 1.234 0.012 0.139 0.004 0.065 31.340 0.300 3.530 0.100
2-219 N70 -219 1 5/16 1 9/16 1/8 1.296 0.012 0.139 0.004 0.658 32.920 0.300 3.530 0.100
2-220 N70 -220 1 3/8 1 5/8 1/8 1.359 0.012 0.139 0.004 0.071 34.520 0.300 3.530 0.100
2-221 N70 -221 1 7/16 1 11/16 1/8 1.359 0.012 0.139 0.004 0.074 36.090 0.300 3.530 0.100
2-222 N70 -222 1 1/2 1 3/4 1/8 1.421 0.015 0.139 0.004 0.077 37.690 0.380 3.530 0.100
2-223 N70 -223 1 5/8 1 7/8 1/8 1.484 0.015 0.139 0.004 0.083 40.870 0.380 3.530 0.100
2-224 N70 -224 1 3/4 2 1/8 1.609 0.015 0.139 0.004 0.089 44.040 0.380 3.530 0.100
2-225 N70 -225 1 7/8 2 1/8 1/8 1.859 0.018 0.139 0.004 0.095 47.220 0.460 3.530 0.100
2-226 N70 -226 2 2 1/4 1/8 1.984 0.018 0.139 0.004 0.101 50.390 0.460 3.530 0.100
New parts are always being added. Call for sizes not shown and seal kits.
372
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-227 N70 -227 2 1/8 2 3/8 1/8 2.109 0.018 0.139 0.004 0.107 53.570 0.460 3.530 0.100
2-228 N70 -228 2 1/4 2 1/2 1/8 2.234 0.020 0.139 0.004 0.113 56.740 0.510 3.530 0.100
2-229 N70 -229 2 3/8 2 5/8 1/8 2.359 0.020 0.139 0.004 0.119 59.920 0.510 3.530 0.100
2-230 N70 -230 2 1/2 2 3/4 1/8 2.484 0.020 0.139 0.004 0.125 63.090 0.510 3.530 0.100
2-231 N70 -231 2 5/8 2 7/8 1/8 2.609 0.020 0.139 0.004 0.131 66.270 0.510 3.530 0.100
2-232 N70 -232 2 3/4 3 1/8 2.734 0.024 0.139 0.004 0.137 69.440 0.610 3.530 0.100
2-233 N70 -233 2 7/8 3 1/8 1/8 2.859 0.024 0.139 0.004 0.143 72.620 0.610 3.530 0.100
2-234 N70 -234 3 3 1/4 1/8 2.984 0.024 0.139 0.004 0.149 75.790 0.610 3.530 0.100
2-235 N70 -235 3 1/8 3 3/8 1/8 3.109 0.024 0.139 0.004 0.155 78.970 0.610 3.530 0.100
2-236 N70 -236 3 1/4 3 1/2 1/8 3.234 0.024 0.139 0.004 0.161 82.140 0.610 3.530 0.100
2-237 N70 -237 3 3/8 3 5/8 1/8 3.359 0.024 0.139 0.004 0.167 85.320 0.610 3.530 0.100
2-238 N70 -238 3 1/2 3 3/4 1/8 3.484 0.024 0.139 0.004 0.173 88.490 0.610 3.530 0.100
2-239 N70 -239 3 5/8 3 7/8 1/8 3.609 0.028 0.139 0.004 0.179 91.670 0.710 3.530 0.100
2-240 N70 -240 3 3/4 4 1/8 3.764 0.028 0.139 0.004 0.185 94.840 0.710 3.530 0.100
2-241 N70 -241 3 7/8 4 1/8 1/8 3.859 0.028 0.139 0.004 0.191 98.020 0.710 3.530 0.100
2-242 N70 -242 4 4 1/4 1/8 3.984 0.028 0.139 0.004 0.197 101.190 0.710 3.530 0.100
2-243 N70 -243 4 1/8 4 3/8 1/8 4.109 0.028 0.139 0.004 0.206 104.370 0.710 3.530 0.100
2-244 N70 -244 4 1/4 4 1/2 1/8 4.234 0.030 0.139 0.004 0.209 107.540 0.760 3.530 0.100
2-245 N70 -245 4 3/8 4 5/8 1/8 4.359 0.030 0.139 0.004 0.214 110.720 0.760 3.530 0.100
2-246 N70 -246 4 1/2 4 3/4 1/8 4.484 0.030 0.139 0.004 0.220 113.890 0.760 3.530 0.100
2-247 N70 -247 4 5/8 4 7/8 1/8 4.609 0.030 0.139 0.004 0.226 117.070 0.760 3.530 0.100
2-248 N70 -248 4 3/4 5 1/8 4.734 0.030 0.139 0.004 0.232 120.240 0.760 3.530 0.100
2-249 N70 -249 4 7/8 5 1/8 1/8 4.859 0.035 0.139 0.004 0.238 123.420 0.890 3.530 0.100
2-250 N70 -250 5 5 1/4 1/8 4.984 0.035 0.139 0.004 0.244 126.590 0.890 3.530 0.100
2-251 N70 -251 5 1/8 5 3/8 1/8 5.109 0.035 0.139 0.004 0.250 129.770 0.890 3.530 0.100
2-252 N70 -252 5 1/4 5 1/2 1/8 5.234 0.035 0.139 0.004 0.256 132.940 0.890 3.530 0.100
2-253 N70 -253 5 3/8 5 5/8 1/8 5.359 0.035 0.139 0.004 0.262 136.120 0.890 3.530 0.100
2-254 N70 -254 5 1/2 5 3/4 1/8 5.484 0.035 0.139 0.004 0.268 139.290 0.890 3.530 0.100
2-255 N70 -255 5 5/8 5 7/8 1/8 5.609 0.035 0.139 0.004 0.274 142.470 0.890 3.530 0.100
2-256 N70 -256 5 3/4 6 1/8 5.734 0.035 0.139 0.004 0.280 145.640 0.890 3.530 0.100
2-257 N70 -257 5 7/8 6 1/6 1/8 5.859 0.035 0.139 0.004 0.286 148.820 0.890 3.530 0.100
2-258 N70 -258 6 6 1/4 1/8 5.984 0.035 0.139 0.004 0.292 151.990 0.890 3.530 0.100
2-259 N70 -259 6 1/4 6 1/2 1/8 6.234 0.040 0.139 0.004 0.304 158.340 1.020 3.530 0.100
2-260 N70 -260 6 1/2 6 3/4 1/8 6.484 0.040 0.139 0.004 0.316 164.690 1.020 3.530 0.100
373
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-261 N70 -261 6 3/4 7 1/8 6.734 0.040 0.139 0.004 0.328 171.040 1.020 3.530 0.100
2-262 N70 -262 7 7 1/4 1/8 6.984 0.040 0.139 0.004 0.340 177.390 1.020 3.530 0.100
2-263 N70 -263 7 1/4 7 1/2 1/8 7.234 0.045 0.139 0.004 0.352 183.740 1.140 3.530 0.100
2-264 N70 -264 7 1/2 7 3/4 1/8 7.484 0.050 0.139 0.004 0.363 190.090 1.270 3.530 0.100
2-265 N70 -265 7 3/4 8 1/8 7.734 0.050 0.139 0.004 0.375 196.440 1.270 3.530 0.100
2-266 N70 -266 8 8 1/4 1/8 7.984 0.050 0.139 0.004 0.387 202.790 1.270 3.530 0.100
2-267 N70 -267 8 1/4 8 1/2 1/8 8.234 0.050 0.139 0.004 0.399 209.140 1.270 3.530 0.100
2-268 N70 -268 8 1/2 8 3/4 1/8 8.484 0.050 0.139 0.004 0.411 215.490 1.270 3.530 0.100
2-269 N70 -269 8 3/4 9 1/8 8.734 0.050 0.139 0.004 0.423 221.840 1.270 3.530 0.100
2-270 N70 -270 9 9 1/4 1/8 8.984 0.050 0.139 0.004 0.435 228.190 1.270 3.530 0.100
2-271 N70 -271 9 1/4 9 1/2 1/8 9.234 0.055 0.139 0.004 0.447 234.540 1.400 3.530 0.100
2-272 N70 -272 9 1/2 9 3/4 1/8 9.484 0.055 0.139 0.004 0.459 240.890 1.400 3.530 0.100
2-273 N70 -273 9 3/4 10 1/8 9.734 0.055 0.139 0.004 0.471 247.240 1.400 3.530 0.100
2-274 N70 -274 10 10 1/4 1/8 9.984 0.055 0.139 0.004 0.489 253.590 1.400 3.530 0.100
2-275 N70 -275 10 1/2 10 3/4 1/8 10.484 0.055 0.139 0.004 0.506 266.290 1.400 3.530 0.100
2-276 N70 -276 11 11 1/4 1/8 10.984 0.065 0.139 0.004 0.530 278.990 1.650 3.530 0.100
2-277 N70 -277 11 1/2 11 3/4 1/8 11.484 0.065 0.139 0.004 0.554 291.690 1.650 3.530 0.100
2-278 N70 -278 12 12 1/4 1/8 11.984 0.065 0.139 0.004 0.578 304.390 1.650 3.530 0.100
2-279 N70 -279 13 13 1/4 1/8 12.984 0.065 0.139 0.004 0.626 329.790 1.650 3.530 0.100
2-280 N70 -280 14 14 1/4 1/8 13.984 0.065 0.139 0.004 0.673 355.190 1.650 3.530 0.100
2-281 N70 -281 15 15 1/4 1/8 14.984 0.065 0.139 0.004 0.721 380.590 1.650 3.530 0.100
2-282 N70 -282 16 16 1/4 1/8 15.955 0.075 0.139 0.004 0.767 405.260 1.910 3.530 0.100
2-283 N70 -283 17 17 1/4 1/8 16.955 0.080 0.139 0.004 0.815 430.660 2.030 3.530 0.100
2-284 N70 -284 18 18 1/4 1/8 17.955 0.085 0.139 0.004 0.863 456.060 2.160 3.530 0.100
2-309 N70 -309 7/16 13/16 3/16 0.412 0.005 0.210 0.005 0.068 10.460 0.130 5.330 0.130
2-310 N70 -310 1/2 7/8 3/16 0.475 0.005 0.210 0.005 0.075 12.070 0.130 5.330 0.130
2-311 N70 -311 9/16 15/16 3/16 0.537 0.007 0.210 0.005 0.081 13.640 0.180 5.330 0.130
2-312 N70 -312 5/8 1 3/16 0.600 0.009 0.210 0.005 0.088 15.240 0.230 5.330 0.130
2-313 N70 -313 11/16 1 1/16 3/16 0.662 0.009 0.210 0.005 0.095 16.810 0.230 5.330 0.130
2-314 N70 -314 3/4 1 1/8 3/16 0.725 0.010 0.210 0.005 0.102 18.420 0.250 5.330 0.130
2-315 N70 -315 13/16 1 3/16 3/16 0.787 0.010 0.210 0.005 0.109 19.990 0.250 5.330 0.130
2-316 N70 -316 7/8 1 1/4 3/16 0.850 0.010 0.210 0.005 0.115 21.590 0.250 5.330 0.130
2-317 N70 -317 15/16 1 5/16 3/16 0.912 0.010 0.210 0.005 0.122 23.160 0.250 5.330 0.130
2-318 N70 -318 1 1 3/8 3/16 0.975 0.010 0.210 0.005 0.129 24.770 0.250 5.330 0.130
New parts are always being added. Call for sizes not shown and seal kits.
374
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-319 N70 -319 1 1/16 1 7/16 3/16 1.037 0.010 0.210 0.005 0.136 26.340 0.250 5.330 0.130
2-320 N70 -320 1 1/8 1 1/2 3/16 1.100 0.012 0.210 0.005 0.143 27.940 0.300 5.330 0.130
2-321 N70 -321 1 3/16 1 9/16 3/16 1.162 0.012 0.210 0.005 0.149 29.510 0.300 5.330 0.130
2-322 N70 -322 1 1/4 1 5/8 3/16 1.225 0.012 0.210 0.005 0.156 31.120 0.300 5.330 0.130
2-323 N70 -323 1 5/16 1 11/16 3/16 1.287 0.012 0.210 0.005 0.163 32.690 0.300 5.330 0.130
2-324 N70 -324 1 3/8 1 3/4 3/16 1.350 0.012 0.210 0.005 0.170 34.290 0.300 5.330 0.130
2-325 N70 -325 1 1/2 1 7/8 3/16 1.475 0.015 0.210 0.005 0.183 37.470 0.380 5.330 0.130
2-326 N70 -326 1 5/8 2 3/16 1.600 0.015 0.210 0.005 0.197 40.640 0.380 5.330 0.130
2-327 N70 -327 1 3/4 2 1/8 3/16 1.725 0.015 0.210 0.005 0.211 43.820 0.380 5.330 0.130
2-328 N70 -328 1 7/8 2 1/4 3/16 1.850 0.015 0.210 0.005 0.224 46.990 0.380 5.330 0.130
2-329 N70 -329 2 2 3/8 3/16 1.975 0.018 0.210 0.005 0.238 50.170 0.460 5.330 0.130
2-330 N70 -330 2 1/8 2 1/2 3/16 2.100 0.018 0.210 0.005 0.251 53.340 0.460 5.330 0.130
2-331 N70 -331 2 1/4 2 5/8 3/16 2.225 0.018 0.210 0.005 0.265 56.520 0.460 5.330 0.130
2-332 N70 -332 2 3/8 2 3/4 3/16 2.350 0.018 0.210 0.005 0.279 59.690 0.460 5.330 0.130
2-333 N70 -333 2 1/2 2 7/8 3/16 2.475 0.020 0.210 0.005 0.292 62.870 0.510 5.330 0.130
2-334 N70 -334 2 5/8 3 3/16 2.600 0.020 0.210 0.005 0.306 66.040 0.510 5.330 0.130
2-335 N70 -335 2 3/4 3 1/8 3/16 2.725 0.020 0.210 0.005 0.319 69.220 0.510 5.330 0.130
2-336 N70 -336 2 7/8 3 1/4 3/16 2.850 0.020 0.210 0.005 0.333 72.390 0.510 5.330 0.130
2-337 N70 -337 3 3 3/8 3/16 2.975 0.024 0.210 0.005 0.347 75.570 0.610 5.330 0.130
2-338 N70 -338 3 1/8 3 1/2 3/16 3.100 0.024 0.210 0.005 0.360 78.740 0.610 5.330 0.130
2-339 N70 -339 3 1/4 3 5/8 3/16 3.225 0.024 0.210 0.005 0.374 81.920 0.610 5.330 0.130
2-340 N70 -340 3 3/8 3 3/4 3/16 3.350 0.024 0.210 0.005 0.387 85.090 0.610 5.330 0.130
2-341 N70 -341 3 1/2 3 7/8 3/16 3.475 0.024 0.210 0.005 0.401 88.270 0.610 5.330 0.130
2-342 N70 -342 3 5/8 4 3/16 3.600 0.028 0.210 0.005 0.415 91.440 0.710 5.330 0.130
2-343 N70 -343 3 3/4 4 1/8 3/16 3.725 0.028 0.210 0.005 0.428 94.620 0.710 5.330 0.130
2-344 N70 -344 3 7/8 4 1/4 3/16 3.850 0.028 0.210 0.005 0.442 97.790 0.710 5.330 0.130
2-345 N70 -345 4 4 3/8 3/16 3.975 0.028 0.210 0.005 0.445 100.970 0.710 5.330 0.130
2-346 N70 -346 4 1/8 4 1/2 3/16 4.100 0.028 0.210 0.005 0.469 104.140 0.710 5.330 0.130
2-347 N70 -347 4 1/4 4 5/8 3/16 4.225 0.030 0.210 0.005 0.483 107.320 0.760 5.330 0.130
2-348 N70 -348 4 3/8 4 3/4 3/16 4.350 0.030 0.210 0.005 0.496 110.490 0.760 5.330 0.130
2-349 N70 -349 4 1/2 4 7/8 3/16 4.475 0.030 0.210 0.005 0.510 113.670 0.760 5.330 0.130
2-350 N70 -350 4 5/8 5 3/16 4.600 0.030 0.210 0.005 0.523 116.840 0.760 5.330 0.130
2-351 N70 -351 4 3/4 5 1/8 3/16 4.725 0.030 0.210 0.005 0.537 120.020 0.760 5.330 0.130
2-352 N70 -352 4 7/8 5 1/4 3/16 4.850 0.030 0.210 0.005 0.551 123.190 0.760 5.330 0.130
375
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-353 N70 -353 5 5 3/8 3/16 4.975 0.037 0.210 0.005 0.564 126.370 0.940 5.330 0.130
2-354 N70 -354 5 1/8 5 1/2 3/16 5.100 0.037 0.210 0.005 0.578 129.540 0.940 5.330 0.130
2-355 N70 -355 5 1/4 5 5/8 3/16 5.225 0.037 0.210 0.005 0.591 132.720 0.940 5.330 0.130
2-356 N70 -356 5 3/8 5 3/4 3/16 5.350 0.037 0.210 0.005 0.605 135.890 0.940 5.330 0.130
2-357 N70 -357 5 1/2 5 7/8 3/16 5.475 0.037 0.210 0.005 0.619 139.070 0.940 5.330 0.130
2-358 N70 -358 5 5/8 6 3/16 5.600 0.037 0.210 0.005 0.632 142.240 0.940 5.330 0.130
2-359 N70 -359 5 3/4 6 1/6 3/16 5.725 0.037 0.210 0.005 0.646 145.420 0.940 5.330 0.130
2-360 N70 -360 5 7/8 6 1/4 3/16 5.850 0.037 0.210 0.005 0.659 148.590 0.940 5.330 0.130
2-361 N70 -361 6 6 3/8 3/16 5.975 0.037 0.210 0.005 0.673 151.770 0.940 5.330 0.130
2-362 N70 -362 6 1/4 6 5/8 3/16 6.225 0.040 0.210 0.005 0.700 158.120 1.020 5.330 0.130
2-363 N70 -363 6 1/2 6 7/8 3/16 6.475 0.040 0.210 0.005 0.727 164.470 1.020 5.330 0.130
2-364 N70 -364 6 3/4 7 1/8 3/16 6.725 0.040 0.210 0.005 0.755 170.820 1.020 5.330 0.130
2-365 N70 -365 7 7 3/8 3/16 6.975 0.040 0.210 0.005 0.782 177.170 1.020 5.330 0.130
2-366 N70 -366 7 1/4 7 5/8 3/16 7.225 0.045 0.210 0.005 0.809 183.520 1.140 5.330 0.130
2-367 N70 -367 7 1/2 7 7/8 3/16 7.475 0.045 0.210 0.005 0.836 189.870 1.140 5.330 0.130
2-368 N70 -368 7 3/4 8 1/8 3/16 7.725 0.045 0.210 0.005 0.863 196.220 1.140 5.330 0.130
2-369 N70 -369 8 8 3/8 3/16 7.975 0.045 0.210 0.005 0.891 202.570 1.140 5.330 0.130
2-370 N70 -370 8 1/4 8 5/8 3/16 8.225 0.050 0.210 0.005 0.918 208.920 1.270 5.330 0.130
2-371 N70 -371 8 1/2 8 7/8 3/16 8.475 0.050 0.210 0.005 0.945 215.270 1.270 5.330 0.130
2-372 N70 -372 8 3/4 9 1/8 3/16 8.725 0.050 0.210 0.005 0.972 221.620 1.270 5.330 0.130
2-373 N70 -373 9 9 3/8 3/16 8.975 0.050 0.210 0.005 0.999 227.970 1.270 5.330 0.130
2-374 N70 -374 9 1/4 9 5/8 3/16 9.225 0.055 0.210 0.005 1.027 234.320 1.400 5.330 0.130
2-375 N70 -375 9 1/2 9 7/8 3/16 9.475 0.055 0.210 0.005 1.054 240.670 1.400 5.330 0.130
2-376 N70 -376 9 3/4 10 1/8 3/16 9.725 0.055 0.210 0.005 1.081 247.020 1.400 5.330 0.130
2-377 N70 -377 10 10 3/8 3/16 9.975 0.055 0.210 0.005 1.108 253.370 1.400 5.330 0.130
2-378 N70 -378 10 1/2 10 7/8 3/16 10.475 0.060 0.210 0.005 1.163 266.070 1.520 5.330 0.130
2-379 N70 -379 11 11 3/8 3/16 10.975 0.060 0.210 0.005 1.217 278.770 1.520 5.330 0.130
2-380 N70 -380 11 1/2 11 7/8 3/16 11.475 0.065 0.210 0.005 1.272 291.470 1.650 5.330 0.130
2-381 N70 -381 12 12 3/8 3/16 11.975 0.065 0.210 0.005 1.326 304.170 1.650 5.330 0.130
2-382 N70 -382 13 13 3/8 3/16 12.975 0.065 0.210 0.005 1.435 329.570 1.650 5.330 0.130
2-383 N70 -383 14 14 3/8 3/16 13.975 0.070 0.210 0.005 1.544 354.970 1.780 5.330 0.130
2-384 N70 -384 15 15 3/8 3/16 14.975 0.070 0.210 0.005 1.652 380.370 1.780 5.330 0.130
2-385 N70 -385 16 16 3/8 3/16 15.955 0.075 0.210 0.005 1.759 405.260 1.910 5.330 0.130
2-386 N70 -386 17 17 3/8 3/16 16.955 0.080 0.210 0.005 1.868 430.660 2.030 5.330 0.130
New parts are always being added. Call for sizes not shown and seal kits.
376
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-387 N70 -387 18 18 3/8 3/16 17.955 0.085 0.210 0.005 1.977 456.060 2.160 5.330 0.130
2-388 N70 -388 19 19 3/8 3/16 18.955 0.090 0.210 0.005 2.085 481.460 2.290 5.330 0.130
2-389 N70 -389 20 20 3/8 3/16 19.955 0.095 0.210 0.005 2.194 506.860 2.410 5.330 0.130
2-390 N70 -390 21 21 3/8 3/16 20.955 0.095 0.210 0.005 2.303 532.260 2.410 5.330 0.130
2-391 N70 -391 22 22 3/8 3/16 21.955 0.100 0.210 0.005 2.412 557.660 2.540 5.330 0.130
2-392 N70 -392 23 23 3/8 3/16 22.955 0.105 0.210 0.005 2.519 583.060 2.670 5.330 0.130
2-393 N70 -393 24 24 3/8 3/16 23.955 0.110 0.210 0.005 2.628 608.460 2.790 5.330 0.130
2-394 N70 -394 25 25 3/8 3/16 24.955 0.115 0.210 0.005 2.737 633.860 2.920 5.330 0.130
2-395 N70 -395 26 26 3/8 3/16 25.955 0.120 0.210 0.005 2.845 659.260 3.050 5.330 0.130
2-401 N70 -401 1 1/2 2 1/4 1.475 0.012 0.275 0.006 0.324 38.100 0.300 6.990 0.150
2-402 N70 -402 1 5/8 2 1/8 1/4 1.600 0.015 0.275 0.006 0.346 37.470 0.380 6.990 0.150
2-403 N70 -403 1 3/4 2 1/4 1/4 1.725 0.015 0.275 0.006 0.371 40.640 0.380 6.990 0.150
2-404 N70 -404 1 7/8 2 3/8 1/4 1.850 0.015 0.275 0.006 0.394 43.820 0.380 6.990 0.150
2-405 N70 -405 2 2 1/2 1/4 1.975 0.015 0.275 0.006 0.417 46.990 0.380 6.990 0.150
2-406 N70 -406 2 1/8 2 5/8 1/4 2.100 0.018 0.275 0.006 0.441 50.170 0.460 6.990 0.150
2-407 N70 -407 2 1/4 2 3/4 1/4 2.225 0.018 0.275 0.006 0.464 53.340 0.460 6.990 0.150
2-408 N70 -408 2 3/8 2 7/8 1/4 2.350 0.018 0.275 0.006 0.487 56.520 0.460 6.990 0.150
2-409 N70 -409 2 1/2 3 1/4 2.475 0.020 0.275 0.006 0.511 59.690 0.510 6.990 0.150
2-410 N70 -410 2 5/8 3 1/8 1/4 2.600 0.020 0.275 0.006 0.534 62.870 0.510 6.990 0.150
2-411 N70 -411 2 3/4 3 1/4 1/4 2.725 0.020 0.275 0.006 0.557 69.220 0.510 6.990 0.150
2-412 N70 -412 2 7/8 3 3/8 1/4 2.850 0.020 0.275 0.006 0.581 72.390 0.510 6.990 0.150
2-413 N70 -413 3 3 1/2 1/4 2.975 0.024 0.275 0.006 0.604 75.570 0.610 6.990 0.150
2-414 N70 -414 3 1/8 3 5/8 1/4 3.100 0.024 0.275 0.006 0.627 78.740 0.610 6.990 0.150
2-415 N70 -415 3 1/4 3 3/4 1/4 3.225 0.024 0.275 0.006 0.651 81.920 0.610 6.990 0.150
2-416 N70 -416 3 3/8 3 7/8 1/4 3.350 0.024 0.275 0.006 0.674 85.090 0.610 6.990 0.150
2-417 N70 -417 3 1/2 4 1/4 3.475 0.024 0.275 0.006 0.697 88.270 0.610 6.990 0.150
2-418 N70 -418 3 5/8 4 1/8 1/4 3.600 0.028 0.275 0.006 0.721 91.440 0.710 6.990 0.150
2-419 N70 -419 3 3/4 4 1/4 1/4 3.725 0.028 0.275 0.006 0.744 94.620 0.710 6.990 0.150
2-420 N70 -420 3 7/8 4 3/8 1/4 3.850 0.028 0.275 0.006 0.767 97.790 0.710 6.990 0.150
2-421 N70 -421 4 4 1/2 1/4 3.975 0.028 0.275 0.006 0.791 100.970 0.710 6.990 0.150
2-422 N70 -422 4 1/8 4 5/8 1/4 4.100 0.028 0.275 0.006 0.814 104.140 0.710 6.990 0.150
2-423 N70 -423 4 1/4 4 3/4 1/4 4.225 0.030 0.275 0.006 0.837 107.320 0.760 6.990 0.150
2-424 N70 -424 4 3/8 4 7/8 1/4 4.350 0.030 0.275 0.006 0.861 110.490 0.760 6.990 0.150
2-425 N70 -425 4 1/2 5 1/4 4.475 0.033 0.275 0.006 0.886 113.670 0.840 6.990 0.150
377
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-426 N70 -426 4 5/8 5 1/8 1/4 4.600 0.033 0.275 0.006 0.910 116.840 0.840 6.990 0.150
2-427 N70 -427 4 3/4 5 1/4 1/4 4.725 0.033 0.275 0.006 0.933 120.020 0.840 6.990 0.150
2-428 N70 -428 4 7/8 5 3/8 1/4 4.850 0.033 0.275 0.006 0.956 123.190 0.840 6.990 0.150
2-429 N70 -429 5 5 1/2 1/4 4.975 0.037 0.275 0.006 0.980 126.370 0.940 6.990 0.150
2-430 N70 -430 5 1/8 5 5/8 1/4 5.100 0.037 0.275 0.006 1.003 129.540 0.940 6.990 0.150
2-431 N70 -431 5 1/4 5 3/4 1/4 5.225 0.037 0.275 0.006 1.026 132.720 0.940 6.990 0.150
2-432 N70 -432 5 3/8 5 7/8 1/4 5.350 0.037 0.275 0.006 1.050 135.890 0.940 6.990 0.150
2-433 N70 -433 5 1/2 6 1/4 5.475 0.037 0.275 0.006 1.073 139.070 0.940 6.990 0.150
2-434 N70 -434 5 5/8 6 1/6 1/4 5.600 0.037 0.275 0.006 1.096 142.240 0.940 6.990 0.150
2-435 N70 -435 5 3/4 6 1/4 1/4 5.725 0.037 0.275 0.006 1.120 145.420 0.940 6.990 0.150
2-436 N70 -436 5 7/8 6 3/8 1/4 5.850 0.037 0.275 0.006 1.143 148.590 0.940 6.990 0.150
2-437 N70 -437 6 6 1/2 1/4 5.975 0.037 0.275 0.006 1.166 151.770 0.940 6.990 0.150
2-438 N70 -438 6 1/4 6 3/4 1/4 6.225 0.040 0.275 0.006 1.213 158.120 1.020 6.990 0.150
2-439 N70 -439 6 1/2 7 1/4 6.475 0.040 0.275 0.006 1.260 164.470 1.020 6.990 0.150
2-440 N70 -440 6 3/4 7 1/4 1/4 6.725 0.040 0.275 0.006 1.306 170.820 1.020 6.990 0.150
2-441 N70 -441 7 7 1/2 1/4 6.975 0.040 0.275 0.006 1.353 177.170 1.020 6.990 0.150
2-442 N70 -442 7 1/4 7 3/4 1/4 7.225 0.045 0.275 0.006 1.400 183.520 1.140 6.990 0.150
2-443 N70 -443 7 1/2 8 1/4 7.475 0.045 0.275 0.006 1.446 189.870 1.140 6.990 0.150
2-444 N70 -444 7 3/4 8 1/4 1/4 7.725 0.045 0.275 0.006 1.493 196.220 1.140 6.990 0.150
2-445 N70 -445 8 8 1/2 1/4 7.975 0.045 0.275 0.006 1.539 202.570 1.140 6.990 0.150
2-446 N70 -446 8 1/2 9 1/4 8.475 0.055 0.275 0.006 1.633 215.270 1.400 6.990 0.150
2-447 N70 -447 9 9 1/2 1/4 8.975 0.055 0.275 0.006 1.726 227.970 1.400 6.990 0.150
2-448 N70 -448 9 1/2 10 1/4 9.475 0.055 0.275 0.006 1.819 240.670 1.400 6.990 0.150
2-449 N70 -449 10 10 1/2 1/4 9.975 0.055 0.275 0.006 1.913 253.370 1.400 6.990 0.150
2-450 N70 -450 10 1/2 11 1/4 10.475 0.060 0.275 0.006 2.006 266.070 1.520 6.990 0.150
2-451 N70 -451 11 11 1/2 1/4 10.975 0.060 0.275 0.006 2.099 278.770 1.520 6.990 0.150
2-452 N70 -452 11 1/2 12 1/4 11.475 0.060 0.275 0.006 2.193 291.470 1.520 6.990 0.150
2-453 N70 -453 12 12 1/2 1/4 11.975 0.060 0.275 0.006 2.286 304.170 1.520 6.990 0.150
2-454 N70 -454 12 1/2 13 1/4 12.475 0.060 0.275 0.006 2.379 316.870 1.520 6.990 0.150
2-455 N70 -455 13 13 1/2 1/4 12.975 0.060 0.275 0.006 2.472 329.570 1.520 6.990 0.150
2-456 N70 -456 13 1/2 14 1/4 13.475 0.07 0.275 0.006 2.566 342.270 1.520 6.990 0.150
2-457 N70 -457 14 14 1/2 1/4 13.975 0.07 0.275 0.006 2.659 354.970 1.780 6.990 0.150
2-458 N70 -458 14 1/2 15 1/4 14.475 0.07 0.275 0.006 2.752 367.670 1.780 6.990 0.150
2-459 N70 -459 15 15 1/2 1/4 14.975 0.07 0.275 0.006 2.846 380.370 1.780 6.990 0.150
New parts are always being added. Call for sizes not shown and seal kits.
378
Inch
O-Rings
Inch O-ring
Standard O-Ring Size Metric O-Ring Size
AS 568A Nominal Sizes
Inches Basic Millimeters
Reference Uniform Inches
Actual Per AS 568A Volume Actual Per AS 568A
Number Dash
Tol.+/- (Cu.in.) Tol.+/-
Number ID OD W ID W Tol.+/- ID W Tol.+/-
2-460 N70 -460 15 1/2 16 1/4 15.475 0.07 0.275 0.006 2.939 393.070 1.780 6.990 0.150
2-461 N70 -461 16 16 1/2 1/4 15.955 0.075 0.275 0.006 3.029 405.260 1.910 6.990 0.150
2-462 N70 -462 16 1/2 17 1/4 16.455 0.075 0.275 0.006 3.122 417.960 1.910 6.990 0.150
2-463 N70 -463 17 17 1/2 1/4 16.955 0.080 0.275 0.006 3.215 430.660 2.030 6.990 0.150
2-464 N70 -464 17 1/2 18 1/4 17.455 0.085 0.275 0.006 3.308 443.360 2.160 6.990 0.150
2-465 N70 -465 18 18 1/2 1/4 17.955 0.085 0.275 0.006 3.402 456.060 2.160 6.990 0.150
2-466 N70 -466 18 1/2 19 1/4 18.455 0.085 0.275 0.006 3.495 468.760 2.160 6.990 0.150
2-467 N70 -467 19 19 1/2 1/4 18.955 0.090 0.275 0.006 3.588 481.460 2.290 6.990 0.150
2-468 N70 -468 19 1/2 20 1/4 19.455 0.090 0.275 0.006 3.682 494.160 2.290 6.990 0.150
2-469 N70 -469 20 20 1/2 1/4 19.955 0.095 0.275 0.006 3.775 506.860 2.410 6.990 0.150
2-470 N70 -470 21 21 1/2 1/4 20.955 0.095 0.275 0.006 3.962 532.260 2.410 6.990 0.150
2-471 N70 -471 22 22 1/2 1/4 21.955 0.100 0.275 0.006 4.418 557.660 2.540 6.990 0.150
2-472 N70 -472 23 23 1/2 1/4 22.940 0.105 0.275 0.006 4.332 582.680 2.670 6.990 0.150
379
Inch
O-Rings
O-ring Back-Up
New parts are always being added. Call for sizes not shown and seal kits.
380
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
381
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
382
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
383
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
384
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
385
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
386
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
387
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
388
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
389
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
390
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
391
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
392
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
393
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
394
Inch
O-Rings
O-ring Back-Up
Part Number ID OD C/S Height
Boss O-ring
O-ring Size (Units are in In) Metric O-ring Size (Units are in mm)
Reference Dash Tube OD
ID Tol. W ID Tol. W
Number Number (Ref)
3-901 -901 3/32 0.185 0.005 0.056 0.003 4,70 0,13 1,42 0,08
3-902 -902 1/8 0.239 0.005 0.064 0.003 6,07 0,13 1,63 0,08
3-903 -903 3/16 0.301 0.005 0.064 0.003 7,65 0,13 1,63 0,08
3-904 -904 1/4 0.351 0.005 0.072 0.003 8,92 0,13 1,83 0,08
3-905 -905 5/16 0.414 0.005 0.072 0.003 10,52 0,13 1,83 0,08
3-906 -906 3/8 0.468 0.005 0.078 0.003 11,89 0,13 1,98 0,08
3-907 -907 7/16 0.530 0.007 0.082 0.003 13,46 0,18 2,08 0,08
3-908 -908 1/2 0.644 0.009 0.087 0.003 16,36 0,23 2,21 0,08
3-909 -909 9/16 0.706 0.009 0.097 0.003 17,93 0,23 2,46 0,08
3-910 -910 5/8 0.755 0.009 0.097 0.003 19,18 0,23 2,46 0,08
3-911 -911 11/16 0.863 0.009 0.116 0.004 21,92 0,23 2,95 0,10
3-912 -912 3/4 0.924 0.009 0.116 0.004 23,47 0,23 2,95 0,10
3-913 -913 13/16 0.986 0.010 0.116 0.004 25,04 0,26 2,95 0,10
3-914 -914 7/8 1.047 0.010 0.116 0.004 26,59 0,26 2,95 0,10
3-916 -916 1 1.171 0.010 0.116 0.004 29,74 0,26 2,95 0,10
3-918 -918 1 1/8 1.355 0.012 0.116 0.004 34,42 0,30 2,95 0,10
3-920 -920 1 1/4 1.475 0.014 0.118 0.004 37,47 0,36 3,00 0,10
3-924 -924 1 1/2 1.720 0.014 0.118 0.004 43,69 0,36 3,00 0,10
3-928 -928 1 3/4 2.090 0.018 0.118 0.004 53,09 0,46 3,00 0,10
3-932 -932 2 2.337 0.018 0.118 0.004 59,36 0,46 3,00 0,10
395
Inch
O-Rings
Gland Dimensions
Industrial Static Seals
Female Gland
Male Gland A - Bore Dia. (male gland)
1/2 E A1 - Groove Dia. (female gland)
B - Tube OD (female gland)
1/2 E B1 - Groove Dia. (male gland)
C - Plug Dia. (male gland)
B1 Dia. (B Min. = A Max. + 2L Max.)
1 B Dia. D - Throat Dia. (female gland)
D Dia.
C Dia. A1 Dia. E - Diametrical Clearance
A Dia. (A Max. = B Min. + 2L Max.)
1
Break Corners
(TYP) Approx. .005 Rad.
W W Pressure Pressure Pressure
.005
1/2 E Max.
32
63 R 63
F L ID W
32
.003
Max.
G Section W.W G G1 G2
No One Two
Parbak Ring Parbak Ring Parbak Ring
004 1/16 .070 .050 to .015 to 22 to .002 to .005 .003 to .093 to .098 .205 to .210 .005 to .002
through +/- .003 .052 .023 32 .098 .015
050
102 3/32 .103 .081 to .017 to 17 to .002 to .005 .140 to .140 to .145 .238 to .243 .005 to .002
through +/- .003 .083 .025 24 .145 .015
178
201 1/8 .139 .111 to .022 to 16 to .003 to .006 .187 to .187 to .192 .275 to .280 .010 to .003
through +/- .004 .113 .032 23 .192 .025
284
309 3/16 .210 .170 to .032 to 15 to .003 to .006 .281 to .281 to .286 .410 to .415 .020 to .004
through +/- .005 .173 .045 21 .286 .035
395
425 1/4 .070 .226 to .040 to 15 to .004 to .007 .375 to .375 to .380 .538 to .543 .020 to .005
through +/- .006 .229 .055 20 .380 .035
475
New parts are always being added. Call for sizes not shown and seal kits.
396
Inch
O-Rings
Gland Dimensions
Face Seal Glands
For Internal Pressure
Break Corners (outward pressure direction)
(TYP) Approx. .005 Rad. dimension the groove by its
inside diameter (Ho) and width:
X L
63 R 63
Surface Finish X
L Groove Depth Ho = Mean OD of O-ring
X (=Gland Depth)
32 For Liquids
16 For Vacuum Tolerance = Minus 1% of Mean
and Gases
G OD, but not more than -.060.
Gland Detail
004 through 050 1/16 .070 +/- .003 .050 to .054 .013 to .023 19 to 32 .101 to .107 .084 to .089 .005 to .015
102 through 178 3/32 .103 +/- .003 .074 to .080 .020 to .032 20 to 30 .136 to .142 .120 to .125 .005 to .015
201 through 284 1/8 .139 +/- .004 .101 to .107 .028 to .042 20 to 30 .177 to .187 .156 to .164 .010 to .025
309 through 395 3/16 .210 +/- .005 .152 to .162 .043 to .063 21 to 30 .270 to .290 .239 to .244 .020 to .035
425 through 475 1/4 .275 +/- .006 .201 to .211 .058 to .080 21 to 29 .342 to .362 .309 to .314 .020 to .035
Special 3/8 .375 +/- .007 .276 to .286 .082 to .108 22 to 28 .475 to .485 .419 to .424 .030 to .045
Special 1/2 .500 +/- .008 .370 to .380 .112 to .138 22 to 27 .638 to .645 .560 to .565 .030 to .045
397
Inch
O-Rings
Gland Dimensions
Industrial Reciprocating Seals (1500 psi max.)
Piston Gland
004 1/16 .070 .055 to .010 to 15 to .002 to .005 .093 to .138 to .143 .205 to .210 .005 to .002
through +/- .003 .057 .018 25 .098 .015
050
102 3/32 .103 .068 to .010 to 10 to .002 to .005 .140 to .171 to .178 .238 to .243 .005 to .002
through +/- .003 .090 .018 17 .145 .015
178
201 1/8 .139 .121 to .012 to 9 to .003 to .006 .187 to .208 to .213 .275 to .280 .010 to .003
through +/- .004 .123 .022 16 .192 .025
284
309 3/16 .210 .185 to .017 to 8 to .003 to .006 .281 to .311 to .316 .410 to .415 .020 to .004
through +/- .005 .188 .030 14 .286 .035
395
425 1/4 .275 .237 to .029 to 11 to .004 to .007 .375 to .408 to .413 .538 to .543 .020 to .005
through +/- .006 .240 .044 16 .380 .035
475
New parts are always being added. Call for sizes not shown and seal kits.
398
Inch
O-Rings
399
Inch
O-Rings
New parts are always being added. Call for sizes not shown and seal kits.
400
Inch
O-Rings
401
Inch
O-Rings
Additional Profiles
ORC
O-ring cord is supplied as a continuous extruded cord. O-ring cord can be used to fabricate custom
O-rings where the standard sizes are not suitable. O-rings can be made from the following compounds:
Fluorocarbon
Silicone
Silicone Sponge
EPDM
Natural Rubber (pure gum)
Aflas
Nitrile
FDA Nitrile
Neoprene
Highly saturated Nitrile (HSN)
Isoprene
Urethane
PTFE
EPDM/Neoprene Sponge
SBR (Styrene Butadiene)
Latex
Square
Rectangular
Quad
U-channels
Tubing
New parts are always being added. Call for sizes not shown and seal kits.
402
Notes
403
Metric
Wipers
Metric
Wipers
Inch
Miscellaneous
New parts are always being added. Call for sizes not shown and seal kits.
404
Metric
Wipers
405
Inch
Miscellaneous
MB Modular B/U
Grizzly Supplies Part Numbers: OD
MB - 125 X 0.125 X 125 ID
New parts are always being added. Call for sizes not shown and seal kits.
406
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
407
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
New parts are always being added. Call for sizes not shown and seal kits.
408
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
409
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
New parts are always being added. Call for sizes not shown and seal kits.
410
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
411
Inch
Miscellaneous
MB Modular B/U
Part Number ID OD Height
New parts are always being added. Call for sizes not shown and seal kits.
412
Inch
Miscellaneous
Prefix ID OD Height
Used to back up rod and piston seals, these provide excellent extrusion resistance. When used with a
u-cup, these shims make it capable for the seal to handle higher pressures.
Part Number
413
Inch
Miscellaneous
NYS-5.735X7.905X.118
NYS-6.00X6.250X.250
NYS-6.00X6.625X.250
NYS-6.750X7.500X.125
NYS-6.750X7.750X.500
NYS-7.00X7.75X.125
NYS-7.250X8.00X.125
NYS-7.250X8.00X.125-TFE
NYS-7.500X8.250X.125
NYS-8.00X8.500X.100
NYS-9.00X9.700X.125
NYS-9.00X9.750X.125
NYS-9.00X9.750X.125-TFE
NYS-9.00X9.875X.125
NYS-9.00X9.875X.250
NYS-9.00X10.00X.250
NYS-9.250X10.00X.125-TFE
NYS-10.00X10.500X.100
NYS-10.500X11.500X.500
NYS-11.00X12.00X.125
NYS-12.00X12.500X.100
NYS-12.00X13.00X.250
NYS-13.00X14.250X.375
NYS-14.500X16.00X.250
New parts are always being added. Call for sizes not shown and seal kits.
414
Inch
Miscellaneous
Retainer Ring
Steel rings used on shafts or in bores and provide a shoulder that accurately positions, locates and
retains other parts of an assembly.
Part Number
415
Inch
Miscellaneous
Additional Profiles
CC
Cushion seal.
OS
Call for profiles not shown. Please call for Inch o-ring kits.
New parts are always being added. Call for sizes not shown and seal kits.
416
Notes
417
Metric
Wipers
Metric
Wipers
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
418
Metric
Wipers
419
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
420
Caterpillar
421
Caterpillar
Maximum extrusion gap Figures show the maximum permissible gap all
on one side using minimum rod and maximum
clearance .
ID OD
Pressure bar 160 250 400
Max. Gap mm 0.6 0.5 0.4
Pressure p.s.i. 2400 3750 6000
Max. Gap in 0.024 0.020 0.016
Height
Molded in urethane, this seal employs an additional lip near the heel.
This twin-lip design provides stability, friction-reducing lube retention, and
contamination resistance.
Rod = 2.00
Groove size = 2.500
PartHeight
Seal Number = .375 ID OD Height
Seal Groove Height = .375 x 1.1 = .412
422
Caterpillar
423
Caterpillar
Groove
Part Number ID OD
Height
5P4673 0.875
9J3497 1.250 1.780 0.140
6J9733 1.500 2.030 0.140
6J6733 1.500
6J9178 1.750 2.280 0.140
6J6917 2.000 2.530 0.140
5J3616 2.250 2.890 0.220
6J6916 2.375 3.020 0.220
5J3620 2.500 3.140 0.220
6J6553 2.750 3.390 0.220
6J6915 3.000 3.640 0.220
6J7167 3.250 3.890 0.220
6J6736 3.500 4.140 0.220
8J6070 3.750 4.390 0.220
8J4627 4.000 4.640 0.220
7J3863 4.000
7J3864 4.000
7J8943 4.250 5.230 0.250
New parts are always being added. Call for sizes not shown and seal kits.
424
Caterpillar
425
Caterpillar
121-4163 11.500
121-4164 11.500
8T7573 12.500
8T7574 12.500
1152136 12.500
1991474 13.500
2260351 13.500
New parts are always being added. Call for sizes not shown and seal kits.
426
Caterpillar
Maximum extrusion gap Figures show the maximum permissible gap all
on one side using minimum rod and maximum
clearance .
Molded in PTFE with a rubber energizer, this seal absorbs the shock of
pressure spikes to protect the rod seal.
Groove
Part Number ID OD
Height
427
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
428
Caterpillar
OD ID
Height
Groove Groove
Part Number OD
Diameter Height
429
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
430
Caterpillar
431
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
432
Caterpillar
433
Caterpillar
Groove Groove
Part Number OD
Diameter Height
New parts are always being added. Call for sizes not shown and seal kits.
434
Caterpillar
Height
Height
Cross
Part Number OD Height
Section
435
Caterpillar
436
Caterpillar
437
Caterpillar
438
Caterpillar
439
Caterpillar
440
Caterpillar
441
Caterpillar
New parts are always being added. Call for sizes not shown and seal kits.
442
Caterpillar
8T8368 3.500
8T8369 3.750
8T8370 4.000
8T8371 4.250
8T8372 4.500
8T8373 4.750
8T8374 5.000
8T8375 5.250
8T8376 5.500
8T8377 6.000
8T8378 6.250
8T8379 6.500
8T8380 7.000
8T8381 7.250
8C0553 7.500
8C4892 7.750
8T8382 8.250
8C4893 8.500
8T8383 9.250
8C4895 10.000
8C4897 10.500
8C4898 11.5000
443
Caterpillar
A B
New parts are always being added. Call for sizes not shown and seal kits.
444
Caterpillar
1P3700 1.000
1P3702 1.250
1P3703 1.500
1P3704 1.750
1P3705 2.000
1P3706 2.250
1P3707 2.375
1P3708 2.500
1P3709 2.750
445
Metric
Wipers
Metric
Wipers
Industrial
Products
New parts are always being added. Call for sizes not shown and seal kits.
446
Metric
Wipers
IT Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
Yellow Chrome Tape & Honing Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449
447
Industrial
Products
IT Tools
New parts are always being added. Call for sizes not shown and seal kits.
448
Industrial
Products
S M27 S W47
449
Industrial
Products
New parts are always being added. Call for sizes not shown and seal kits.
450
Industrial
Products
451
Seal Failures: Causes and Solutions
Failure Condition Cause Solution
Hardening
Swelling
Wear
Wear
Uneven wear on one side of Worn bearing or wear ring. Replace bearings to withstand
sealing lip. Excessive lateral load. a heavy load.
Wear
452
Seal Failures: Causes and Solutions
Failure Condition Cause Solution
Pressure side of seal appears Residual air has exploded at Check maximum pressure.
burned and broken. high pressure. Dieseling. Bleed air from system.
Fracturing
453
Terms and Conditions
1. ENTIRE AGREEMENT/ORDERS. No order for Grizzly Supplies Ltd. (Grizzly) goods shall be binding
upon Grizzly until acknowledged in writing by Grizzly. All orders and acknowledgements are conditioned
on credit screening and approval. Grizzlys acknowledgement and these Terms and Conditions constitute
the entire agreement between Grizzly and Purchaser. Any purchase order, offer or counter-offer made
by Purchaser before or after Grizzlys acknowledgement is rejected. For example, orders submitted on
Purchasers own purchase order forms modifying, adding to, contrary to, or inconsistent with these Terms
and Conditionsare expressly rejected and of no force or effect. In no event will Grizzly be deemed to have
in any way changed, enlarged or modified its liabilities or obligations as fixed by these Terms and Conditions
including, without limitation, situations in which Grizzly satisfies an order submitted on Purchasers own
Purchase order form.
Purchaser shall have been deemed to agree to these Terms and Conditions upon payment of any related
invoice submitted by Grizzly, acceptance of delivery of Grizzly goods or failing to expressly notify Grizzly in
writing within five (5) days of receipt of Grizzlys acknowledgement of any objections it may have to these
Terms and Conditions
No acknowledgement by Grizzly and no provision of Grizzlys Terms and Conditions shall be subject to
change in any manner except as agreed to in writing by an officer of Grizzly.
2. PRICES. All prices are subject to change without notice and quoted in Canadian or US dollars unless
otherwise noted. Written quotations expire thirty (30) calendar days from the date of quotation unless
specified otherwise. Prices do not include Goods and Service Tax, Provincial Sales Tax or any other
government taxes or charges. All taxes and other governmental charges upon the production, manufacture,
distribution, sale or use of the goods to the extent required or not forbidden by law to be collected by Grizzly
from Purchaser, shall be paid by Purchaser to Grizzly unless Purchaser furnishes Grizzly with exemption
certificates acceptable to the relevant taxing authorities. Typographical and/or clerical errors made by
Grizzly are subject to correction.
3. TERMS OF PAYMENT. For all purchases not made on account, payment shall be made by cash or
credit card, authorization of which is required before the order will be processed. Invoices are net thirty
(30) days from the date of invoice unless specified otherwise and approved in writing by Grizzly. Past due
accounts will bear interest at the rate of 2% per month of the invoiced amount. All invoices are payable in
Canadian dollars, unless specified otherwise and approved. Acceptance of bank drafts, checks or other
form of payment shall be subject to immediate collection of the full face amount thereof. Grizzly may, at
its discretion, impose a transaction fee on payments processed via wire transfer or by Letter of Credit.
Grizzly reserves the right at any time and in its sole discretion to demand full or partial payment before
proceeding with a contract of sale. If delivery is delayed or deferred by Purchaser beyond the scheduled
date, payment shall be due in full when Grizzly is prepared to deliver. The goods may thereafter, at Grizzlys
option, be stored at the risk and expense of Purchaser. If Purchaser defaults when any payment is due, the
whole contract price shall become due and payable upon demand or Grizzly, at its option, without prejudice
to other lawful remedies, may defer delivery or cancel the contract. Minimum values on invoice may apply.
454
Terms and Conditions
4. DELIVERY. Grizzly shall not be liable for any damage as a result of any non-delivery or delay due to any
cause beyond Grizzlys reasonable control, including, without limitation, an act of God; act of Purchaser;
embargo; other government act, regulation or request; fire; accident; strike; war; boycott; slowdown; riot;
or delay in transportation or inability to obtain necessary labor, materials, or manufacturing facilities. In the
event of any such delay, the date of delivery, at Grizzlys option, shall be extended for a period equal to the
time lost by reasons of the delay.
5. SHIPMENT/RISK OF LOSS. All shipments are subject to an overrun or shortage of 10% of the quantity
specified. Unless otherwise noted, all quoted prices and sales of goods are made FOB point of shipment
for all orders unless stated otherwise. Delivery dates given in advance of actual shipment of goods or
performance of services are estimates and shall not be deemed to represent fixed or guaranteed delivery
dates. Method and route of shipment will be at the discretion of Grizzly unless specified otherwise by
Purchaser and agreed by Grizzly, and any additional expense of the method or route of shipment specified
by Purchaser shall be borne by Purchaser. Purchaser is responsible for all import/export licenses, permits,
or authorization. Claims for shortage or other errors must be made in writing to Grizzly within five (5) days
after receipt of shipment. Failure to give such notice shall constitute unqualified acceptance and a waiver
of all such claims by Purchaser.
To the extent legal title to the goods shall be deemed to pass to Purchaser at the time of delivery and prior
to performance of all of Purchasers obligations, equitable title shall remain in Grizzly until payment in full
of the purchase price, and Purchaser shall grant and by acceptance of the goods shall deemed to have
granted to Grizzly a first security interest in all goods to secure payment of the purchase price and all other
amounts owed to Grizzly.
Grizzly reserves the right to make delivery of goods in installments, unless otherwise expressly stipulated in
the agreement for sale. Such installments, when separately invoiced, shall be paid for when due per invoice
without regard to subsequent deliveries. Delay in delivery of any installment shall not relieve Purchaser of
its obligations to accept remaining deliveries.
6. WARRANTY/CLAIMS. Purchaser acknowledges that it has selected and ordered goods based on its
own skill and judgment and agrees that it is responsible for ensuring that the goods selected are fit for
Purchasers purpose. Grizzly warrants to the Purchaser only that its goods have been produced in accord
with Grizzlys standard practices with regard to materials and workmanship. This warranty is limited to
goods that are used in accordance with published specifications and only for a period of one year from date
of purchase. Grizzly will, subject to the terms of this warranty, replace or repair, at its option, any defective
good. Thewarranty period for the repaired or replaced product shall extend after the date of repair or
replacement for a time equal to the original warranty period. No goods are to be returned to Grizzly without
prior written consent.
(a) THIS WARRANTY IS IN LIEU OF ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ANY
OTHER OBLIGATION ON THE PART OF THE SELLER.
(b) Grizzly shall have no obligation under this warranty if damage to the good occurs because of improper
handling or operation, modification of the good, abuse, misuse, unauthorized repairs made or attempted
and/or where equipment is operated above rated capacity.
(c) No agent, employee or representative of Grizzly has authority to bind Grizzly to any affirmation,
455
Terms and Conditions
7. LIMITATION OF LIABILITY/INDEMNITY. Grizzlys liability on any claim for loss or damage arising out
of this transaction or from the performance or breach thereof or connected with any goods or services
supplied hereunder, or the sale, resale, operation or use of goods, whether based on contract, warranty,
tort (including negligence) or other grounds, shall not exceed the price allocable to such goods or services
or part thereof involved in the claim, regardless of cause or fault. This limitation of liability reflects a
deliberate and bargained-for allocation of risks between Grizzly and Purchaser and constitutes the basis of
the parties bargain, without which Grizzly would not have agreed to the price or terms of this transaction.
Grizzly shall not, under any circumstances, be liable for any labor charges without its prior written consent.
GRIZZLY SHALL NOT IN ANY EVENT BE LIABLE WHETHER AS A RESULT OF BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) PESONAL INJURY, DEATH, DISMEMBERMENT OR
OTHER GROUNDS FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT
NOT LIMITED TO, LOSS OF PROFITS OR REVENUE, LOSS OF USE OF GOODS OR ASSOCIATED
PRODUCTS, BUSINESS INTERRUPTION, COST OF CAPITAL, COST OF SUBSTITUTE GOODS,
FACILITIES OR SERVICES, DOWNTIME COSTS, OR CLAIMS OF CUSTOMERS OF PURCHASER FOR
SUCH DAMAGE. In addition, if Grizzly furnishes Purchaser with advice or other assistance regarding
any goods or services supplied hereunder, or any system or equipment in which any such goods may be
installed, and which is not required pursuant to this transaction, the furnishing of the advice or assistance
will not subject Grizzly to any liability, whether based on contract, warranty, tort (including negligent) or other
grounds.
In the event Purchaser modifies Grizzly goods or incorporates Grizzly goods into another product
or component part, Purchaser agrees to hold harmless and indemnify Grizzly from any and all claims,
liabilities, losses, costs and expenses (including reasonable attorneys fees) involving personal injury or
property damage. Purchaser also agrees to hold harmless and indemnify Grizzly from any patent or other
intellectual property claims related to any Grizzly goods made in accordance with Purchasers designs or
specifications.
8. WAIVER AND CHOICE OF LAW. The failure of Grizzly to insist in any one or more instances, upon the
performance of any of the Terms and Conditions as set forth herein or the failure of Grizzly to exercise any
of its rights hereunder shall not be construed as a waiver or relinquishment of any such terms, conditions
or rights there under and shall not effect Grizzlys right to insist on strict performance and compliance with
regard to any future performance of these Terms and Conditions. Alltransactions shall be governed by
the laws of British Columbia, Canada and applicable federal laws of Canada. The provisions of the United
Nations Convention on Contracts for the International Sale of Goods shall not apply.
456
Terms and Conditions
9. DISPUTE RESOLUTION/ATTORNEYS FEES. All disputes arising out of or in connection with this
agreement that does not exceed the sum of $50,000 CAD, exclusive of interest and costs, or in respect of
any legal relationship associated with or derived from this agreement, shall be finally resolved by arbitration
pursuant to the National Arbitration Rules of the ADR Institute of Canada, Inc. The place of arbitration shall
be in Vancouver, BC Canada. The language of the arbitration shall be English.
Any dispute, controversy or claim arising out of this transaction where the matter in controversy exceeds
the sum of $50,000, exclusive of interest and costs shall be adjudicated exclusively by a court of competent
jurisdiction in British Columbia, Canada. Purchaser consents to personal jurisdiction and venue in the City
of Vancouver, Canada and agrees not to take any action to challenge such jurisdiction or venue. Grizzly
may bring an action against Purchaser in any jurisdiction or venue.
In the event of any action or proceeding related to this transaction, and Grizzly is determined to be the
prevailing party with regard to some or all claims, Purchaser agrees to pay all of Grizzlys attorneys fees
and litigation costs up through and including any appeal.
457
Warranty
Grizzly Supplies Ltd. guarantees its products to be free from defects in workmanship and raw materials.
Our liability for breach of any and all warranties is limited to refunding our invoice price of the product or
at our option, replacement of the parts free of charge, but no cost of installation. The sale of our products
under any other warranty or guarantee, expressed or implied, is not authorized by the corporation.
All technical advise recommendations and services are rendered by seller gratis. They are based on
technical data which the seller believes to be reliable and are intended for the use by persons having
skill and know how, at their own risk. Seller assumes no responsibility for results obtained or damages
occurred from their use by buyer in whole or in part.
458
Notes