Professional Documents
Culture Documents
1 Input Data: Profis Anchor 2.6.4
1 Input Data: Profis Anchor 2.6.4
4
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HVZ M16x105
Effective embedment depth: hef = 105 mm, hnom = 125 mm
Material: 8.8
Evaluation Service Report: ETA 03/0032
Issued I Valid: 6/4/2013 | 6/4/2018
Proof: Design method ETAG (No. 001 Annex C/2010)
Stand-off installation: eb = 0 mm (no stand-off); t = 16 mm
Anchor plate: ; E = 210000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.100
lx x ly x t = 210 mm x 210 mm x 16 mm; (Recommended plate thickness: calculated (13 mm))
Profile: Square hollow; (L x W x T) = 100 mm x 100 mm x 5 mm
Base material: cracked concrete, C35/45, fcc = 45.00 N/mm2; h = 500 mm, Temp. short/long: 30/40 C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: reinforcement spacing < 150 mm (any ) or < 100 mm ( <= 10 mm)
with longitudinal edge reinforcement d >= 12
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.6.4
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.6.4
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.6.4
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
7 Warnings
Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the anchor plate without creating air voids and before application of the loads.
The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.6.4
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
8 Installation data
Anchor plate, steel: ; E = 210000.00 N/mm2; fyk = 275.00 N/mm2 Anchor type and diameter: HVZ M16x105
Profile: Square hollow; 100 x 100 x 5 mm Installation torque: 0.090 kNm
Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm
Plate thickness (input): 16 mm Hole depth in the base material: 125 mm
Recommended plate thickness: calculated (13 mm) Minimum thickness of the base material: 160 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
105 105
30
3 4
105
150
x
105
1 2
30
30 150 30
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.6.4
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 4/4/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan