Professional Documents
Culture Documents
MAX1490AEPG2b 12335
MAX1490AEPG2b 12335
MAX1480A/B/C/MAX1490A/B
The MAX1480A/MAX1480B/MAX1480C/MAX1490A/ For Integrated ESD Protection
MAX1490B are complete, electrically isolated, RS-485/ MAX1480E/MAX1490E: 15kV ESD-Protected,
RS-422 data-communications interface solutions in a Isolated RS-485/RS-422 Data Interfaces
hybrid microcircuit. Transceivers, optocouplers, and a For Space-Constrained Applications
transformer provide a complete interface in a standard MAX3157: High CMRR, RS-485 Transceiver with
DIP package. A single +5V supply on the logic side pow- 50V Isolation
ers both sides of the interface.
The MAX1480B/MAX1480C/MAX1490B feature reduced- _______________Ordering Information
slew-rate drivers that minimize EMI and reduce reflec- PART TEMP RANGE PIN-PACKAGE
tions caused by improperly terminated cables, allowing MAX1480ACPI 0C to +70C 28 Wide Plastic DIP
error-free data transmission at data rates up to 250kbps.
MAX1480AEPI -40C to +85C 28 Wide Plastic DIP
The MAX1480A/MAX1490A driver slew rate is not limited,
allowing transmission rates up to 2.5Mbps. The Ordering Information continued at end of data sheet.
Data rate for A parts is up to 2.5Mbps. Data rate for B and
MAX1480A/B/C are designed for half-duplex communi-
C parts is up to 250kbps.
cation, while the MAX1490A/B feature full-duplex com-
munication.
_____________________Selection Table
Drivers are short-circuit current limited and protected
against excessive power dissipation by thermal shut- DRIVER
HALF/ DATA SLEW-
down circuitry that places the driver outputs into a high- PART
ENABLE
FULL RATE RATE
impedance state. The receiver input has a fail-safe TIME
DUPLEX (MBPS) LIMITED
feature that guarantees a known output (RO low for the (s)
MAX1480A/B/C, RO high for the MAX1490A/B) if the MAX1480A Half 2.5 No 0.2
input is open circuit.
MAX1480B Half 0.25 Yes 35
The MAX1480A/MAX1480B/MAX1480C/MAX1490A/ MAX1480C Half 0.25 Yes 0.5
MAX1490B typically withstand 1600VRMS (1 minute) or
2000VRMS (1 second). Their isolated outputs meet all MAX1490A Full 2.5 No
RS-485/RS-422 specifications. The MAX1480A/B/C are MAX1490B Full 0.25 Yes
available in a 28-pin DIP package, and the MAX1490A/B
are available in a 24-pin DIP package. Pin Configurations
________________________Applications
TOP VIEW
Isolated RS-485/RS-422 Data Interface VCC1 1 24 AC1 MAX1490A/B
Transceivers for EMI-Sensitive Applications VCC2 2 23 AC2
Industrial-Control Local Area Networks D1 3 22 ISO VCC1
FS 6 19 B
SD 7 18 Z
VCC3 8 17 Y
DI 9 16 ISO COM1
ISOLATION BARRIER
DIP
Pin Configurations continued at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxims website at www.maxim-ic.com.
Complete, Isolated RS-485/RS-422
Data Interface
ABSOLUTE MAXIMUM RATINGS
MAX1480A/B/C/MAX1490A/B
With Respect to GND_ LED Forward Current (DI, DE, ISO RO LED) ......................50mA
Supply Voltage (VCC_)...........................................-0.3V to +6V Continuous Power Dissipation (TA = +70C)
Control Input Voltage (SD, FS)...............-0.3V to (VCC_ + 0.3V) 24-Pin Plastic DIP (derate 8.7mWC above +70C) .....696mW
Receiver Output Voltage (RO, RO)........-0.3V to (VCC_ + 0.3V) 28-Pin Plastic DIP (derate 9.09mW/C above +70C) ..727mW
Output Switch Voltage (D1, D2)........................................+12V Operating Temperature Ranges
With Respect to ISO COM_ MAX1480_CPI/MAX1490_CPG ............................0C to +70C
Control Input Voltage (ISO DE_ ) ....-0.3V to (ISO VCC_ + 0.3V) MAX1480_EPI/MAX1490_EPG .........................-40C to +85C
Driver Input Voltage (ISO DI_ ) .......-0.3V to (ISO VCC_ + 0.3V) Storage Temperature Range .............................-65C to +160C
Receiver Output Voltage (ISO RO_) ...-0.3V to (ISO VCC_ + 0.3V) Lead Temperature (soldering, 10s) .................................+300C
Driver Output Voltage (A, B, Y, Z ) ......................-8V to +12.5V
Receiver Input Voltage (A, B)..............................-8V to +12.5V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC_ = 5V 10%, VFS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.) (Notes 1, 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
fSWL VFS = 0V 535
Switch Frequency kHz
fSWH FS = VCC_ or open 725
MAX1480A, RL = , +25C only 60 90
DE = VCC_ or open RL = 54 120
MAX1480B, RL = , +25C only 35 45
DE = VCC_ or open RL = 54 95
MAX1480C, RL = , +25C only 35 75
Operating Supply Current ICC mA
DE = VCC_ or open RL = 54 95
RL = , +25C only 100 150
MAX1490A
RL = 54 170
RL = , +25C only 65 125
MAX1490B
RL = 54 130
Shutdown Supply Current
ISHDN SD = VCC_ 0.2 A
(Note 3)
VSDH High 2.4
Shutdown Input Threshold V
VSDL Low 0.8
Shutdown Input Leakage Current 10 pA
VFSH High 2.4
FS Input Threshold V
VFSL Low 0.8
FS Input Pullup Current FS low 50 A
FS Input Leakage Current FS high 10 pA
Input High Voltage VIH DE, DI VCC_ - 0.4 V
Input Low Voltage VIL DE, DI 0.4 V
Isolation Resistance RISO TA = +25C, VISO = 50VDC 100 10,000 M
Isolation Capacitance CISO TA = +25C, VISO = 50VDC 10 pF
Differential Driver Output
VOD1 8 V
(No Load)
2 _______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
ELECTRICAL CHARACTERISTICS (continued)
MAX1480A/B/C/MAX1490A/B
(VCC_ = 5V 10%, VFS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.) (Notes 1, 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Differential Driver Output R = 50 (RS-422) 2
VOD2 V
(With Load) R = 27 (RS-485), Figure 4 1.5 5.0
Change in Magnitude of Differential 0.3
R = 27 or 50,
Differential Output Voltage for VOD V
Figure 4 Common mode 0.3
Complementary Output States
Driver Common-Mode Output
VOC R = 27 or 50, Figure 4 4 V
Voltage
MAX1480A/B/C 1
DE = 0V, VIN = 12V
MAX1490A/B 0.25
Input Current (A, B) ISO IIN VCC_ = 0V mA
or 5.5V MAX1480A/B/C 0.8
VIN = -7V
MAX1490A/B 0.2
MAX1480A/B/C 48
Receiver Input Resistance RIN -7V VCM 12V k
MAX1490A/B 12
Receiver Differential Threshold
VTH -7V VCM 12V -0.2 +0.2 V
Voltage
Receiver Input Hysteresis VTH VCM = 0V 70 mV
Receiver Output/Receiver Output Using resistor values listed in
VOL 0.4 V
Low Voltage Tables 1 and 2
Receiver Output/Receiver Output
IOH VOUT = 5.5V 250 A
High Current
Driver Short-Circuit Current ISO IOSD -7V VO 12V (Note 4) 100 mA
SWITCHING CHARACTERISTICSMAX1480A/MAX1490A
(VCC_ = 5V 10%, FS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Driver Input to Output tPLH Figures 5 and 7, RDIFF = 54, CL1 = CL2 100 275
ns
Propagation Delay tPHL = 100pF 100 275
Figures 5 and 7, RDIFF = 54, CL1 = CL2
Driver Output Skew tSKEW 25 90 ns
= 100pF
Figures 5 and 7, RDIFF = 54, CL1 = CL2
Driver Rise or Fall Time tR, tF 15 40 ns
= 100pF
Driver Enable to Output High
tZH Figures 6 and 8, CL = 100pF, S2 closed 0.2 1.5 s
(MAX1480A Only)
Driver Enable to Output Low
tZL Figures 6 and 8, CL = 100pF, S1 closed 0.2 1.5 s
(MAX1480A Only)
Driver Disable Time from Low
tLZ Figures 6 and 8, CL = 15pF, S1 closed 0.2 1.5 s
(MAX1480A Only)
Driver Disable Time from High
tHZ Figures 6 and 8, CL = 15pF, S2 closed 0.2 1.5 s
(MAX1480A Only)
Receiver Input to Output tPLH Figures 5 and 10, RDIFF = 54, CL1 = CL2 100 225
ns
Propagation Delay tPHL = 100pF 100 225
_______________________________________________________________________________________ 3
Complete, Isolated RS-485/RS-422
Data Interface
SWITCHING CHARACTERISTICSMAX1480A/MAX1490A (continued)
MAX1480A/B/C/MAX1490A/B
(VCC_ = 5V 10%, FS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
|tPLH - tPHL| Differential Receiver Figures 5 and 10, RDIFF = 54, CL1 = CL2
tSKD 20 ns
Skew = 100pF
Maximum Data Rate fMAX tPLH, tPHL < 50% of data period 2.5 Mbps
Time to Shutdown tSHDN 100 s
Shutdown to Driver Output High tZH(SHDN) Figures 6 and 9, CL = 100pF, S2 closed 3 10 s
Shutdown to Driver Output Low tZL(SHDN) Figures 6 and 9, CL = 100pF, S1 closed 3 10 s
SWITCHING CHARACTERISTICSMAX1480B/MAX1480C/MAX1490B
(VCC_ = 5V 10%, FS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.)
4 _______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
SWITCHING CHARACTERISTICSMAX1480B/MAX1480C/MAX1490B (continued)
MAX1480A/B/C, MAX1490A/B
(VCC_ = 5V 10%, FS = VCC_, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC_ = 5V and TA = +25C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Driver Disable Time from Low
tLZ Figures 6 and 8, CL = 15pF, S1 closed 2.0 4.5 s
(MAX1480C Only)
Driver Disable Time from High
tHZ Figures 6 and 8, CL = 15pF, S2 closed 2.0 4.5 s
(MAX1480C Only)
Receiver Input to Output tPLH Figures 5 and 10, RDIFF = 54, 2 3.0
s
Propagation Delay tPHL CL1 = CL2 = 100pF 2 3.0
|tPLH - tPHL| Differential Receiver Figures 5 and 10, RDIFF = 54,
tSKD 1200 ns
Skew CL1 = CL2 = 100pF
Maximum Data Rate fMAX tPLH, tPHL < 50% of data period 0.25 Mbps
Time to Shutdown tSHDN 100 s
Shutdown to Driver Output High tZH(SHDN) Figures 6 and 9, CL = 100pF, S2 closed 35 100 s
Shutdown to Driver Output Low tZL(SHDN) Figures 6 and 9, CL = 100pF, S1 closed 35 100 s
Note 1: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to logic-
side ground (GND_), unless otherwise specified.
Note 2: For DE and DI pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480A/
MAX1480B/MAX1480C, Figure 2 for MAX1490A/MAX1490B).
Note 3: Shutdown supply current is the current at VCC1 and VCC2 when shutdown is enabled.
Note 4: Applies to peak current (see Typical Operating Characteristics). Although the MAX1480A/B/C and MAX1490A/B provide
electrical isolation between logic ground and signal paths, they do not provide isolation between external shields and the
signal paths (see Isolated Common Connection section).
_______________________________________________________________________________________ 5
Complete, Isolated RS-485/RS-422
Data Interface
__________________________________________Typical Operating Characteristics
MAX1480A/B/C, MAX1490A/B
OUTPUT CURRENT vs. OUTPUT CURRENT vs. RECEIVER OUTPUT HIGH VOLTAGE
RECEIVER OUTPUT LOW VOLTAGE RECEIVER OUTPUT HIGH VOLTAGE vs. TEMPERATURE
80 -30 5.00
MAX1480/90A/B-01
MAX1480/90A/B-02
MAX1480/90A/B-03
MEASURED AT ISO RO DRV MEASURED AT ISO RO DRV MEASURED AT ISO RO DRV
IRO = 8mA
70 4.75
-25
-20
50 4.25
40 -15 4.00
30 3.75
-10
20 3.50
-5
10 3.25
0 0 3.00
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -40 -20 0 20 40 60 80
OUTPUT LOW VOLTAGE (V) OUTPUT HIGH VOLTAGE (V) TEMPERATURE (C)
RECEIVER OUTPUT LOW VOLTAGE OUTPUT CURRENT vs. OUTPUT CURRENT vs.
vs. TEMPERATURE DRIVER OUTPUT LOW VOLTAGE DRIVER OUTPUT HIGH VOLTAGE
0.8 180 -100
MAX1480/90A/B-04
MAX1480/90A/B-05
MAX1480/90A/B-06
MEASURED AT ISO RO DRV
IRO = 8mA 160 -90
0.7
-80
OUTPUT LOW VOLTAGE (V)
0.6 140
OUTPUT CURRENT (mA)
-70
120
0.5
-60
100
0.4 -50
80
0.3 -40
60
-30
0.2
40 -20
0.1 20 -10
0 0 0
-40 -20 0 20 40 60 80 0 1 2 3 4 5 6 7 8 9 10 11 12 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6
TEMPERATURE (C) OUTPUT LOW VOLTAGE (V) OUTPUT HIGH VOLTAGE (V)
70
2.8 MEASURED AT VCC1 AND VCC2
SHUTDOWN CURRENT (A)
60 0.30
OUTPUT CURRENT (mA)
2.7
50 2.6 0.25
40 2.5 0.20
2.4 0.15
30
2.3
20 0.10
2.2
10 0.05
2.1
0 2.0 0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
DIFFERENTIAL OUTPUT VOLTAGE (V) TEMPERATURE (C) TEMPERATURE (C)
6 _______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
_____________________________Typical Operating Characteristics (continued)
MAX1480A/B/C, MAX1490A/B
(VCC_ = 5V, FS = VCC_, TA = +25C, unless otherwise noted.)
MAX1480/90A/B-10
MAX1480/90A/B-11
MAX1480/90A/B-12
VCC = 5.5V RL = 54
VCC = 5.5V RL = 54 110
140 120
VCC = 5.5V RL = 54
VCC = 5.0V 100 VCC = 5.0V
120
SUPPLY CURRENT (mA)
MAX1490A MAX1490B
SUPPLY CURRENT vs. TEMPERATURE SUPPLY CURRENT vs. TEMPERATURE
200 150
MAX1480/90A/B-14
MAX1480/90A/B-13
VCC = 5.5V
RL = 54
VCC = 5.5V 140
180 VCC = 5.0V
130
VCC = 5.0V
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
MAX1480B
DRIVER DISABLE TIME (s)
MAX1480B
DRIVER ENABLE TIME (s)
10 10
RL = 54
VDI = 0V MEASURED FROM
DE TO VALID OUTPUT
MAX1480C
1 RL = 54 1
MAX1480C
VDI = 0V MEASURED FROM
DE TO VALID OUTPUT
MAX1480A MAX1480A
0.1 0.1
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
TEMPERATURE (C) TEMPERATURE (C)
_______________________________________________________________________________________ 7
Complete, Isolated RS-485/RS-422
Data Interface
_____________________________Typical Operating Characteristics (continued)
MAX1480A/B/C, MAX1490A/B
(VCC_ = 5V, FS = VCC_, VDI = 0V, DE toggled 0V to 5V at 5kHz, TA = +25C, unless otherwise noted.)
MAX1480A MAX1480A
DRIVER ENABLE TIME DRIVER DISABLE TIME
MAX1480/90-20
MAX1480/90-19
DRIVER DRIVER
OUTPUT B OUTPUT B
2V/div 2V/div
DE DE
2V/div 2V/div
200ns/div 200ns/div
VCC_ = 5.0V, DI= 0V VCC_ = 5.0V, DI = 0V
DE TOGGLED 0V TO 5V AT 5kHz DE TOGGLED 0V TO 5V AT 5kHz
MAX1480B MAX1480B
DRIVER ENABLE TIME DRIVER DISABLE TIME
MAX1480/90-18
MAX1480/90-17
DRIVER
OUTPUT B DRIVER
2V/div OUTPUT B
2V/div
DE
DE
2V/div
2V/div
10s/div 5s/div
VCC_ = 5.0V, DI= 0V VCC_ = 5.0V, DI= 0V
DE TOGGLED 0V TO 5V AT 5kHz DE TOGGLED 0V TO 5V AT 5kHz
MAX1480C MAX1480C
DRIVER ENABLE TIME DRIVER DISABLE TIME
MAX1480/90-26
MAX1480/90-25
DRIVER DRIVER
OUTPUT B OUTPUT B
2V/div 2V/div
DE DE
2V/div 2V/div
500ns/div 500ns/div
VCC_ = 5.0V, DI= 0V VCC_ = 5.0V, DI = 0V
DE TOGGLED 0V TO 5V AT 5kH DE TOGGLED 0V TO 5V AT 5kHz
8 _______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
_____________________________Typical Operating Characteristics (continued)
MAX1480A/B/C, MAX1490A/B
(VCC_ = 5V, FS = VCC_, DE = VCC_, VDI = 0V to 5V at 1.25MHz, TA = +25C, unless otherwise noted.)
MAX1480A/MAX1490A MAX1480A/MAX1490A
RECEIVER tPHL RECEIVER tPLH
MAX1480/90-21 MAX1480/90-22
RECEIVER RECEIVER
INPUT A INPUT B
1V/div 1V/div
RECEIVER RECEIVER
INPUT B INPUT A
1V/div 1V/div
RO/RO RO/RO
2V/div 2V/div
20ns/div 20ns/div
VCC_ = 5.0V, DE= VCC_ VCC_ = 5.0V, DE= VCC_
DI = 0V TO 5V AT 1.25MHz DI = 0V TO 5V AT 1.25MHz
MAX1480B/MAX1480C/MAX1490B MAX1480B/MAX1480C/MAX1490B
RECEIVER tPHL RECEIVER tPLH
MAX1480/90-23 MAX1480/90-24
RECEIVER RECEIVER
INPUT A INPUT A
1V/div 1V/div
RECEIVER RECEIVER
INPUT B INPUT B
1V/div 1V/div
RO/RO RO/RO
2V/div 2V/div
200ns/div 500ns/div
VCC_ = 5.0V, DE= VCC_ VCC_ = 5.0V, DE= VCC_
DI= 0V TO 5V AT 125kHz DI= 0V TO 5V AT 125kHz
POWER-UP DELAY TO DRIVER OUTPUTS VALID
MAX1480/90-16
DRIVER
OUTPUT B
(Z FOR MAX1490)
2V/div
SD
2V/div
1s/div
VDI = 0V
VSD = 5V TO 0V AT 1kHz
_______________________________________________________________________________________ 9
Complete, Isolated RS-485/RS-422
Data Interface
________________________________________________________________Pin Description
MAX1480A/B/C, MAX1490A/B
PIN
NAME FUNCTION
MAX1480A/B/C MAX1490A/B
PINS
PINSONONTHETHENON-ISOLATED
NON-ISOLATEDSIDE
SIDE
1, 2, 8, 10 1, 2, 8, 10 VCC1VCC4 Logic-Side (nonisolated side) +5V Supply Voltages
3, 4 3, 4 D1, D2 Internal Connections. Leave these pins unconnected.
5 5 GND1 Logic-Side Ground. Connect to GND2 (pin 12).
Frequency Select Input. If FS = VCC_ or is open, switch frequency is high; if FS
6 6 FS = GND, switch frequency is low. For optimal performance and minimal supply
current, connect FS to VCC_ or leave unconnected.
Shutdown Input. Ground for normal operation. When high, the power oscillator is
7 7 SD
disabled.
Driver Input. With DE high (MAX1480A/B/C only), a low on DI forces output A
low and output B high. Similarly, a high on DI forces output A high and output
9 9 DI
B low. Drives internal LED cathode through a resistor (Table 1 of Figure 1 for
MAX1480A/B/C, Table 2 of Figure 2 for MAX1490A/B).
10 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
___________________________________________________Pin Description (continued)
MAX1480A/B/C, MAX1490A/B
PIN
NAME FUNCTION
MAX1480A/B/C MAX1490A/B
Note: For DE and DI pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480A/B/C,
Figure 2 for MAX1490A/B).
Detailed Description Use the FS pin to select between high and low switching
frequencies for the isolated power driver. The driver
The MAX1480A/MAX1480B/MAX1480C/MAX1490A/ switches at the lower frequency 535kHz when FS is low,
MAX1490B are complete, electrically isolated, RS-485/ and at the higher frequency 725kHz when FS is high. The
RS-422 data-communications interface solutions. FS pin has a weak internal pull-up that switches the
Transceivers, optocouplers, a power driver, and a device to the high-frequency mode when FS is left
transformer in one standard 28-pin DIP package (24- unconnected. With FS high or open, no-load supply
pin for the MAX1490A/B) provide a complete interface. current is reduced by approximately 4mA, and by up to
Signals and power are internally transported across the 8mA when fully loaded. For optimal performance and
isolation barrier (Figures 1, 2). Power is transferred from minimal supply current, connect FS to VCC_ or leave
the logic side (nonisolated side) to the isolated side of unconnected.
the barrier through a center-tapped transformer.
Signals cross the barrier through high-speed optocou- Drivers are short-circuit current limited and are protect-
plers. A single +5V supply on the logic side powers ed against excessive power dissipation by thermal
both sides of the interface. The MAX1480A/B/C offer shutdown circuitry that puts the driver outputs into a
half-duplex communications while the MAX1490A/B high-impedance state. The receiver input has a fail-safe
feature full-duplex communication. The functional feature that guarantees a logic-high RO (logic-low RO)
input/output relationships are shown in Tables 36. output if the input is open circuit.
The MAX1480B/MAX1480C/MAX1490B feature reduced- On the MAX1480A/B/C, the driver outputs are enabled
slew-rate drivers that minimize EMI and reduce reflec- by bringing DE high. Driver-enable times are typically
tions caused by improperly terminated cables, allowing 0.2s for the MAX1480A, 35s for the MAX1480B, and
error-free transmission at data rates up to 250kbps. The 0.5s for the MAX1480C. Allow time for the devices to be
MAX1480A/MAX1490A driver slew rate is not limited, enabled before sending data (see the Driver Enable
allowing transmission rates up to 2.5Mbps Time vs. Temperature graph in the Typical Operating
Characteristics). When enabled, driver outputs function
The MAX1480B/MAX1480C/MAX1490B shutdown feature
as line drivers. Driver outputs are high impedance when
reduces supply current to as low as 0.2A by using the
DE is low. While outputs are high impedance, they func-
SD pin (see the Low-Power Shutdown Mode section).
tion as line receivers.
______________________________________________________________________________________ 11
Complete, Isolated RS-485/RS-422
Data Interface
MAX1480A/B/C, MAX1490A/B
VCC3
ISO VCC1
MAX845 D1
Q MAX1480A: MAX1487
N MAX1480B: MAX487
OSC MAX1480C: MAX487
FS T F/F
1.07MHz/ ISO DI IN B
1.45MHz D2 D
Q
N ISO DE IN A
ISO RO DRV R
SD GND1 RE
ISO COM1
TERMINATING RESISTOR
MAX1480A/B/C (ONE RESISTOR ON EACH END)
VIN VCC1
1 28 AC1 (MAKE NO CONNECTION)
5V TWISTED PAIR
VCC2 TO OTHER TRANSCEIVERS
C1 C2 2 27 AC2 (MAKE NO CONNECTION)
D1 3 26 ISO VCC1 B RL
22F 0.1F
B
D2 4 25
SHIELD (OPTIONAL)
GND1 ISO RO DRV
5 24
A TWISTED PAIR
MAX845 MAX1487
FS 6 23 A TO OTHER TRANSCEIVERS
MAX487
SD
74HC86 7 22 ISO DI IN R6 SH RL
OR EQUIVALENT VCC3 ISO DE IN
8 21
R1 R4 SHIELD (OPTIONAL)
DI DRIVER INPUT DI
9 20 ISO COM1
DI VCC4
10 19 ISO DI DRV
R2
DE DRIVER ENABLE DE R5 NOTE: RESISTOR R7 PROTECTS
11 18 ISO VCC2 THE MAX1480A/B/C FROM TRANSIENT
DE R7
GND2
R3 12 17 ISO DE DRV 100 CURRENTS BETWEEN SHIELD AND
RECEIVER OUTPUT TRANSMISSION LINES.
RO 13 ISO COM2
16
RO VCC5 ISO RO LED
14 15
12 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
MAX1480A/B/C, MAX1490A/B
VCC3
MAX845 D1
Q
N
OSC R A
FS 1.07MHz/ T F/F
1.45MHz ISO RO DRV
D2 B
Q ISO DI DRV MAX1490A: MAX490
N
MAX1490B: MAX488 Z
SD GND1 Y
MAX1490A/B
VIN EXTERNAL RS-485/RS-422 WIRING
5V
VCC1 TERMINATING RESISTOR
C1 C2 1 24 AC1 (MAKE NO CONNECTION)
(ONE RESISTOR ON EACH END)
VCC2
22F 0.1F 2 23 AC2 (MAKE NO CONNECTION)
TWISTED PAIR
D1 3 22 ISO VCC1 TO OTHER TRANSCEIVERS
D2 4 21 ISO RO DRV RL RL
GND1 5 20 A A
SHIELD (OPTIONAL)
MAX488
MAX490
MAX845
FS 6 19 B B
SD 7 18 Z Z TWISTED PAIR
RL
74HC86 TO OTHER TRANSCEIVERS
OR EQUIVALENT VCC3 8 17 Y Y
R1 RL
R5, 100
DI DRIVER INPUT DI 9 16 ISO COM1 SH1
DI VCC4 10 R4
15 ISO DI DRV SH2 SHIELD (OPTIONAL)
RECEIVER OUTPUT R2
R0 11 14 ISO VCC2 R6, 100
RO R3
GND2 12 13 ISO RO LED
NOTE: RESISTORS R5 AND R6 PROTECT
THE MAX1490A/B FROM TRANSIENT
ISOLATION BARRIER ISOLATED COMMON CURRENTS BETWEEN SHIELD AND
TRANSMISSION LINES.
LOGIC GROUND
Under these conditions, the MAX1480B/MAX1480C/ tion, SD is low, turning the MOSFET on and thereby pro-
MAX1490B supply current is reduced to as low as 0.2A. viding power to all the VCC_ pins. When SD is pulled high,
The high-speed optocouplers on the MAX1480A/ the power oscillator is disabled and the switch is turned
MAX1480C/MAX1490A consume an additional 10mA off, disconnecting power from the DI and DE optocou-
through VCC5 (VCC4 for the MAX1490A). Therefore, to plers. In normal operating mode, the switch carries only
completely shut down these devices, use an external P- the optocoupler currents, so an on-resistance of several
channel MOSFET as shown in Figure 3. In normal opera- ohms will not significantly degrade efficiency.
______________________________________________________________________________________ 13
Complete, Isolated RS-485/RS-422
Data Interface
MAX1480A/B/C, MAX1490A/B
ISOLATION BARRIER
GND
Test Circuits
* OPTOCOUPLER
CL2 OUTPUTS. SEE FIGURES 1
AND 2 FOR DETAILED BLOCK
DIAGRAM AND TYPICAL
APPLICATION CIRCUIT.
14 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
____________________________________________________Test Circuits (continued)
MAX1480A/B/C, MAX1490A/B
ISO VCC_
500 S1
OUTPUT
UNDER TEST
CL
S2
Switching Waveforms
B tZL tLZ
A, B
VO
2.3V OUTPUT NORMALLY LOW VOL + 0.5V
A VOL
1/2 VO
VDIFF = V (A) - V (B) OUTPUT NORMALLY HIGH
VO A, B
VDIFF 0V 90% 90% VOH - 0.5V
10% 10% 2.3V
-VO 0V
tR tF tZH tHZ
tSKEW = tPLH - tPHL
Figure 7. Driver Propagation Delays and Transition Times Figure 8. Driver Enable and Disable Times
VID INPUT
2.4V 0V 0V
SD -VID
1.6V 1.6V
0.8V VA - VB
______________________________________________________________________________________ 15
Complete, Isolated RS-485/RS-422
Data Interface
MAX1480B/MAX1480C/MAX1490B: _____________________Function Tables
MAX1480A/B/C, MAX1490A/B
Table 4. Receiving
INPUTS* OUTPUT
DE VA - VB (RO)
10dB/div 0 +0.2V 0
0 -0.2V 1
0 Open 0
0Hz 5MHz
500kHz/div Full-Duplex Devices
(MAX1490A/MAX1490B)
Figure 11. Driver Output Waveform and FFT Plot of
MAX1480A/MAX1490A Transmitting a 150kHz Signal
Table 5. Transmitting
INPUT* OUTPUTS
(DI) Z Y
1 0 1
0 1 0
* For DE and DI pin descriptions, see Detailed Block Diagram
and Typical Application Circuit (Figure 1 for MAX1480A/B/C,
Figure 2 for MAX1490A/B).
10dB/div
Table 6. Receiving
INPUT OUTPUT
(VA - VB) (RO)
0Hz 5MHz +0.2V 1
500kHz/div
-0.2V 0
Figure 12. Driver Output Waveform and FFT Plot of Open 1
MAX1480B/MAX1480C/MAX1490B Transmitting a 150kHz
Signal
16 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
MAX1480A/B/C, MAX1490A/B
TERMINATING RESISTOR
(ONE RESISTOR ON EACH END)
B
DI
D
120
DE
A
A B A B R RO
100
RE
RE R RE R
D D
RO DE DI RO DE DI
TERMINATING RESISTOR
VIN (ONE RESISTOR ON EACH END)
5V MAX1480A/B/C
VCC1
1 28 AC1 (MAKE NO CONNECTION)
VCC2
C1 C2 2 27 AC2 (MAKE NO CONNECTION)
D1 3 26 ISO VCC1 B
22F 0.1F
D2 4 25 B
GND1 ISO RO DRV
5 24 120
A
MAX845 MAX487
FS 6
MAX1487 23 A
R6
SD
74HC86 7 22 ISO DI IN SH
R4 SHIELD
OR EQUIVALENT VCC3 ISO DE IN
8 21 (OPTIONAL)
R1
DI DRIVER INPUT DI
9 20 ISO COM1 NOTE: RESISTOR R7 PROTECTS
R5 THE MAX1480A/B/C FROM
VCC4
10 19 ISO DI DRV TRANSIENT CURRENTS
R2
DE DRIVER ENABLE DE BETWEEN SHIELD AND
11 18 ISO VCC2 TRANSMISSION LINES.
GND2 R7
R3 12 17 ISO DE DRV 100
RECEIVER OUTPUT
RO 13 ISO COM2
16
RO VCC5 ISO RO LED
14 15
______________________________________________________________________________________ 17
Complete, Isolated RS-485/RS-422
Data Interface
Driver Output Protection ___________Applications Information
MAX1480A/B/C, MAX1490A/B
VIN
MAX1490A/B
5V
VCC1
C1 C2 1 24 AC1 (MAKE NO CONNECTION)
VCC2
22F 0.1F 2 23 AC2 (MAKE NO CONNECTION)
D1 3 22 ISO VCC1 Y
120
D2 4 21 ISO RO DRV D DI
120
GND1 5 20 A A Z
SHIELD (OPTIONAL)
MAX845
MAX488
MAX490
FS 6 19 B B
SD 7 18 Z Z 120
74HC86 B
OR EQUIVALENT VCC3 8 17 Y Y
R1 R5, 100 120 R RO
DI DI 9 16 ISO COM1 SH1 A
DI R4 SHIELD (OPTIONAL)
VCC4 10 15 ISO DI DRV SH2
DRIVER INPUT R2
RO 11 14 ISO VCC2 R6, 100
RO RECEIVER OUTPUT R3 NOTE: RESISTORS R5 AND R6 PROTECT
GND2 12 13 ISO RO LED THE MAX1490A/B FROM TRANSIENT
CURRENTS BETWEEN SHIELD AND
ISOLATED COMMON TRANSMISSION LINES.
ISOLATION BARRIER
LOGIC GROUND
18 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
Connections and components from one side should The DI and DE (MAX1480A/B/C only) inputs are the
MAX1480A/B/C, MAX1490A/B
not be located near those of the other side. cathodes of LEDs whose anodes are connected to the
A shield trace connected to the ground on each side supply. These points are best driven by a CMOS-logic
of the barrier can help intercept capacitive currents gate with a series resistor to limit the current. The resis-
that might otherwise couple into the signal path. In a tor values shown in Tables 1 and 2 are recommended
double-sided or multilayer board, these shield traces when the 74HC86 gate or equivalent is used. These
should be present on all conductor layers. values may need to be adjusted if a driving gate with
dissimilar series resistance is used.
Try to maximize the width of the isolation barrier
wherever possible; a clear space of at least 0.25 All pull-up resistors are based on optocoupler specifica-
inches between ground and isolated common is tions in order to optimize the devices data-transfer rates.
suggested. Isolated Common Connection
Pullup and LED Drive Resistors The isolated common may be completely floating with
The MAX1480A/MAX1480B/MAX1480C/MAX1490A/ respect to the logic ground and the effective network
MAX1490B are specified and characterized using the ground. The receiver input resistors will cause the iso-
resistor values shown in Table 1 of Figure 1 and Table lated common voltage to go to the mean voltage of the
2 of Figure 2. Altering the recommended values can receiver inputs. If using shielded cable, connect the
degrade performance. isolated common to the shield through a 100 resistor.
In the case of the MAX1490, each shield should have
its own 100 resistor (Figures 1, 2, 13, and 14).
+5V +5V
26 3k 26
74HC04
3k MAX1480C 200
MAX1480C
3k
9 4 3 13
3k 19 19
3k
22 DRIVER DRIVER 22
17 ENABLE ENABLE
17
21 200 200 21
B>A A>B
24 11 11 24
200 200
15 15
5 7 12 5 7 12
+5V +5V
51k 1000pF 51k 1000pF
16 15 14 7 6
2 B Q 13 10 B Q 5
74HC123 74HC123
1 A Q 4 9 A Q 12
CLR CLR
3 11
______________________________________________________________________________________ 19
Complete, Isolated RS-485/RS-422
Data Interface
Doubly Isolated RS-485 Repeater In the idle state, both transmitters are disabled, while all
MAX1480A/B/C, MAX1490A/B
The RS-422/RS-485 standard is specified for cable receivers in the system are enabled. If any device on
lengths up to 4000 feet. When approaching or exceed- the system has information for any other device, it starts
ing the specified maximum cable length, a ground- sending its data onto the bus. Each data transmission
potential difference of several tens of volts can easily on the bus retriggers the one-shot, keeping the sending
develop. This difference can be either DC, AC, at transmitter enabled until there are no more transmis-
power-line frequency, or any imaginable noise or sions. All receivers receive all data; if this is undesir-
impulse waveform. It is typically very low impedance so able, the protocol must allow for an address field so
that if a connection between the two grounds is receivers can ignore data not directed to them.
attempted, very large currents may flow. These cur- Each node must refrain from transmitting when data
rents are by their nature unstable and unpredictable. In already exists on the bus, and must resend data that is
addition, they may cause noise to be injected into sen- corrupted by the collisions that inevitably occur with a
sitive instrumentation and, in severe cases, might actu- party-line system. With the repeater of Figure 15, there
ally cause physical damage to such equipment. might be transmitters up to 8000 feet apart. That repre-
Figure 15 shows a half-duplex (two-wire), bidirectional, sents more than 8s (assuming 1ns/foot of delay) in
party-line repeater system that prevents interference which two nodes could be transmitting simultaneously.
and/or damage from ground-potential differences. Two The circuit in Figure 15 can be used either directly as
MAX1480A/MAX1480B/MAX1480C isolated RS-485 shown, with the slew-rate-limited MAX1480B/MAX1480C,
transceivers are used to isolate each of the network for data transfer rates up to 250kbps, or with the
segments from the electrical environment of the MAX1480A for data rates up to 2.5Mbps (see Table 1
repeater. The MAX1480A/MAX1480B/MAX1480C also for pullup and LED resistor values when using the
regenerate bus signals that may have been degraded MAX1480A, MAX1480B, or MAX1480C). If dual-port iso-
by line attenuation or dispersion. lation is not needed, one of the MAX1480C devices can
be replaced by a MAX487 for 250kbps applications.
20 ______________________________________________________________________________________
Complete, Isolated RS-485/RS-422
Data Interface
Pin Configurations (continued) Ordering Information (continued)
MAX1480A/B/C, MAX1490A/B
PART TEMP RANGE PIN-PACKAGE
TOP VIEW MAX1480BCPI 0C to +70C 28 Wide Plastic DIP
MAX1480A/B/C MAX1480BEPI -40C to +85C 28 Wide Plastic DIP
MAX1480CCPI 0C to +70C 28 Wide Plastic DIP
VCC1 1 28 AC1
MAX1480CEPI -40C to +85C 28 Wide Plastic DIP
VCC2 2 27 AC2 MAX1490ACPG 0C to +70C 24 Wide Plastic DIP
D1 3 26 ISO VCC1 MAX1490AEPG -40C to +85C 24 Wide Plastic DIP
D2 4 25 B MAX1490BCPG 0C to +70C 24 Wide Plastic DIP
GND1 5 24 ISO RO DRV MAX1490BEPG -40C to +85C 24 Wide Plastic DIP
MAX845 MAX487
FS 6 23 A Data rate for A parts is up to 2.5Mbps. Data rate for B and
MAX1487
C parts is up to 250kbps.
SD 7 22 ISO DI IN
VCC3 8 21 ISO DE IN
ISOLATION BARRIER
DIP
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 21
2005 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.