Professional Documents
Culture Documents
Elnet LTE UserManual PDF
Elnet LTE UserManual PDF
Elnet LTE UserManual PDF
Operating Instructions
Revision 1.4
Table of Contents
1.General specifications .................................................................. 2
1.1. Technical Data: ..................................................................... 2
1.2. Measurement and Display Range: ....................................... 3
2.Settings and measurements.......................................................... 4
2.1. Current transformer ratio setting: ...................................... 4
2.2. Voltage transformer ratio setting: ....................................... 5
2.3. Measured values display: ..................................................... 6
2.4. Peak display: ......................................................................... 6
2.5. Indication LEDs: ................................................................... 7
2.6. No volt & phase order alarm relay (option):....................... 8
3.Installations .................................................................................. 9
3.1. Mechanical installation: ....................................................... 9
3.2. Wiring diagram: ................................................................. 11
4.MODBUS Protocol: .................................................................... 12
4.1. MODBUS Framing ............................................................. 12
4.2. RTU Frame Format: ........................................................... 13
4.3. Address Field: ..................................................................... 13
4.4. Function Field: .................................................................... 13
4.5. Data Field: ........................................................................... 14
4.6. Check Field: ........................................................................ 14
4.7. Registers for Elnet LTE Powermeter: ............................... 15
4.8. Register addresses:.............................................................. 16
5.Communication Settings:........................................................... 17
5.1. Communication Address: ................................................... 17
5.2. Baud Rate: ........................................................................... 17
5.3. Available Baud Rates for the ElNet LTE ........................... 17
5.4. Parity: .................................................................................. 17
6. Communication & Alarms Settings.......................................... 18
6.1. To set up Communication ................................................... 18
6.2. To set up Alarms: ................................................................ 19
1
Dear customer, thank you for selecting the Elnet LTE Multimeter for
measurements of voltage, current, power, power factor and energy.
1. General specifications
2
1.2. Measurement and Display Range:
3
2. Settings and measurements
4
5. The current transformer setting screen will appear.
5
4. Use the "" button until you see the message "End"
on screen and then press "Enter".
1. Use the " " buttons to browse among all the display
screens including display of voltage, current, power,
frequency, power factor, power measurement (Active,
Reactive, and Apparent), Active and Reactive energy
and the THD voltage and current.
7
2.6. No volt & phase order alarm relay (option):
8
3. Installations
3.1. Mechanical installation:
Height
90 mm
Width
90 mm
9
Please insert the ELNET LTE Powermeter into
the suitable space prepared in advance. Make
sure you insert the device in the right direction.
The device is equipped with a plastic knob for
adjustment when installed in electrical panels.
The thickness of the panel door should be less
than 4mm.
10
3.2. Wiring diagram:
11
4. MODBUS Protocol:
The ElNet LTE Energy & Power Multimeter has a serial interface
port allowing direct interface with an external communication
network supporting the MODBUS Protocol.
MODBUS is an Industry Standard, widely known and commonly
used communications protocol. Using MODBUS provides
communication between a PC and up to 247 Powermeter slaves on
a common line - the PC being the master and the powermeters the
slaves. The PC initiates the transaction (either a query or
broadcast) and the Powermeter(s) responds. Powermeters respond
to the master PCs request, but will not initiate any transmission
on its own. The PC sends a single Query transaction and the
Powermeter responds in a single response frame and is capable of
only one query and one response at a time.
12
4.2. RTU Frame Format:
Query and response information is sent in frames.
Each frame contains: Address; Function; Data;
Check.
13
Function Codes : 03;04;06;16
Function Meaning in Action
MODBUS
Function 03 Read holding Obtain data from
register Powermeter
Function 04 Read input Obtain data from
register Powermeter (Read register)
Function 06 Preset single Transmit data to
register Powermeter (Write single
register)
Function 16 Preset multiple Transmit data to
register Powermeter (Write multiple
register)
14
4.7. Registers for Elnet LTE Powermeter:
15
Function 04 will respond with a composite reply of both
register 1 and 2 giving the full FLOAT value (in IEEE
Format) from that field i.e. 230.5V.
http://www.ddc.co.il/elnet-pdf/elnet_comm.pdf
16
5. Communication Settings:
17
6. Communication & Alarms Settings
18
6.2. To set up Alarms:
4. In order to set the Low Voltage alarm - use the " "
buttons to scroll to "AL" and press "Enter".
5. The SET ALARM screen will appear - use the " " buttons
to define the Low Voltage level for activating the alarm
and press "Enter".
6. In order to set the Phase Order alarm - use the " "
buttons to scroll to Ord and press "Enter".
7. The Phase Order alarm will appear, use the " " buttons in
order to activate\deactivate the alarm (change from No to
Yes).
19
Functions List:
20