Professional Documents
Culture Documents
Pioneer Deh 1950 Crt3821 Sm.
Pioneer Deh 1950 Crt3821 Sm.
CRT3821
DEH-1950/XU/CN5
CD RECEIVER
DEH-1950 /XU/CN5
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3166 CRT3582 S10.5STD CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
SAFETY INFORMATION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
C regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
D
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.
DEH-1950/XU/CN5
2
1 2 3 4
5 6 7 8
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEH-1950/XU/CN5
5 6 7 8
3
1 2 3 4
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING ................................................................................................................................................... 6
2.2 EXTERIOR................................................................................................................................................. 8
2.3 CD MECHANISM MODULE..................................................................................................................... 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 14
3.3 KEYBOARD UNIT.................................................................................................................................... 20
3.4 CD MECHANISM MODULE..................................................................................................................... 22
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 26
4.1 TUNER AMP UNIT................................................................................................................................... 26
4.2 KEYBOARD UNIT.................................................................................................................................... 30
B 4.3 CD CORE UNIT(S10.5) ........................................................................................................................... 32
5. ELECTRICAL PARTS LIST ............................................................................................................................ 34
6. ADJUSTMENT ............................................................................................................................................... 38
6.1 CD ADJUSTMENT................................................................................................................................... 38
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 40
6.3 ERROR MODE ........................................................................................................................................ 42
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 43
7. GENERAL INFORMATION ............................................................................................................................. 44
7.1 DIAGNOSIS ............................................................................................................................................. 44
7.1.1 DISASSEMBLY ..................................................................................................................................... 44
7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 47
7.2 PARTS...................................................................................................................................................... 48
C 7.2.1 IC .......................................................................................................................................................... 48
7.2.2 DISPLAY ............................................................................................................................................... 58
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 59
8. OPERATIONS ................................................................................................................................................ 60
DEH-1950/XU/CN5
4
1 2 3 4
5 6 7 8
1. SPECIFICATIONS
DEH-1950/XU/CN5
5 6 7 8
5
1 2 3 4
B
17
13
16
C
12
15
1
2
9
10
E
6
11
14
4 5 7
DEH-1950/XU/CN5
6
1 2 3 4
5 6 7 8
PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
DEH-1950/XU/CN5
5 6 7 8
7
1 2 3 4
2.2 EXTERIOR
7
25 14
11
12
23 60
6
59
1
13
1
2
B 57 2
15
1 18
22 17 16
61
21
1 A
A 58
A
4
20 28
58
39 39 29
C
39 26
24
39 27
46 B
48
51
50
47
49
D 52 19 9
43
53
42
44
55
3
54 45
40
41 2
37
E 33
38
34
56
8 32
35
36
31
10 30
F
5
DEH-1950/XU/CN5
8
1 2 3 4
5 6 7 8
EXTERIOR SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
31 Spring CBH2367
32 Spring CBH2961
33 Spring CBH2962
34 Cover CNN1665
35 Panel CNS8760
36 Arm CNV9311
37 Arm CNV9312
38 Detach Grille Assy CXC7319 E
39 Screw BPZ20P100FTC
40 Button(Detach) CAC9382
41 Button(1-6) CAC9863
42 Button(<,>,UP,DOWN) CAC9864
43 Button(SOURCE,BAND) CAC9861
44 Button(AUDIO,FUNC) CAC9862
45 Spring CBH2210
46 Cover CNS8744
47 LCD CAW1931 F
48 Connector(CN1801) CKS5663
49 Holder CND3642
DEH-1950/XU/CN5
5 6 7 8
9
1 2 3 4
DEH-1950/XU/CN5
10
1 2 3 4
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201
36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211
41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV8189
45 Gear CNV7219
46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV8448
49 Arm CNV7805
DEH-1950/XU/CN5
5 6 7 8
11
1 2 3 4
LDET
REFB
CE1
1
IFB
REFA
CE2
DO
CK
IFA
DI
SL-IN
SLOUT
AM_ANT
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
SLOUT
CE1
RFGND1
RFGND2
RFGND3
RFGND4
VDD
DO
IFOUTB
CE2
LDET
IFOUTA
VCC
DI
DGND
REFINA
REFINB
ANT
CK
SLIN
IC2
EEPROM SL-IN
IFA
IFB
REFA
REFB
LDET
B DI
CK
CE1
DO
VCO LFP CE2
SLOUT
ATT
ATT TANK
IC1
MIX / IF / PLL
ATT RF LFP
ELEC
CF SOU
FM/AM TUNER UNIT
C TUNL
1
IN1_L
CDL
2
IN2_L
SYSPW
SYSTEM M
COMPUT
IC 601(2
REGULATOR IC PN5010
1 47
D
PICKUP UNIT
C CD CORE UNIT(S10.5) SWD5V
5
6 IC 911
2
3
36
15
POWEROFF
BSENS
SWVDD SYSPW
(P10.5)(SERVICE) D RF-AMP,CD DECODER,
DIGITAL SERVO /
SYS+B
VDD
7
8
BA4918-V12 4
10
1
SWVDD
B.UP
VDD
DATA PROCESSOR 9
LASER CN101 CN702 CN651
DIODE LD- 1
15 15 Q101 LD
MD 2 LOUT
5 5 PD 19 LOUT
REFO LOUT 16 3
VREF 8 93
8 REFOUT
SWVDD
AC,BD,F,E
HOLOGRAM
UNIT XTAL 25
85 DREG
Q601
FOM FOM X201
3 3 CD 16.93MHz
FOP FOP /XTAL 23
MONITOR
FOCUS ACT. 2 2 DRIVER 9
TOP
DIODE TRACKING ACT. 1 1 TOP REGC(M)
VDD 55
TOM
4 4
TOM IC301 PLL_VDD
LD+ BA5839FP IC201 Q102 57
14 14 TD,FD DVDD3
12
VO1(+)
PE5497B VDD
11 94
VCC 8 VDD
11 DVDD2
VO1(-) SD,MD
14 121
VO2(+) 42 DVDD4
13 PA7/CD3V
VO2(-)
E SPINDLE
MOTOR M PC7/CDMUTE
54 CDMUTE
8 11
16 29 /RESET 10 RESET 16
VO3(-) 22 41 RESET 9 CDRESET
LDIN PA6/LOEJ
15
VO3(+) 21 40
18 CNT PA5/CLCONT
LOAD/ CARRIAGE VO4(-)
MOTOR M 17
VO4(+) MUTE
9 39 BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
PA4/CONT VD
BDATA,BSCK
Q991 CD VD
VD VD
VD 2 17 B.UP
36 Q992
PA1/12SNS 1 18
37
PA2/8SNS 5
38
PA3/DSCSNS
35 126
PA0/HOME VDCONT
DEH-1950/XU/CN5
12
1 2 3 4
5 6 7 8
SYSTEM MICRO
COMPUTER
IC 601(1/2)
PN5010A
SL-IN 62
SL-
IFA 77 IF_INA
CN351
IFB 78 IF_INB RL 2
REFA 96
FREF_A
REFB 97 FREF_B Q351
LDET 99 LOCK
DI 100
DI B
CK 101 CK
CE1 102 CE
DO 103
DO
CE2 109 CE2
SLOUT 136 SL CN901
ACC SENSE 1 1
Q931 B.UP
BACK UP
59 35 ASENS ACC
L_OUT ASENS 3 3
ACC
2 2
GND
ELECTRONIC VOLUME/
SOURCE SELECTOR
FL 23 FL
10 10
7 12 AMP
TUNL
1
IN1_L
Rear_L RLIn IC 301 FL+
21 FL+
12 12
FL
C
PAL007C 3 RL FL+
RL 9 9
6 14 5 RL
Front_L FLIn RL+ RL+
11 11
RL+
IC 151
CDL
2
PML014A 22 25 B.REMOTE
IN2_L IN4+_L 4 AUX-L MUTE NC/BREM 6 6
5 AUX-G 6 B.REM
IN4-_L VCC B.UP
4
STBY VCC 20
VCK, VDT, VST
SYSPW
MUTE
Q201(2/2)
SYSTEM MICRO
COMPUTER MUTE
IC 601(2/2) Q201(1/2)
PN5010A
47 44
POWEROFF MUTE
36
BSENS
D
15
SYSPW
1
SWVDD
B.UP
SWVDD
85 DREG 82
XOUT
X601
81 74.1MHz
9 XIN
REGC(M)
55
57
PLL_VDD
DVDD3
AUX IN
1 2
B KEYBOARD UNIT
52
BU_X1 CN831 CN1801
AUX L
AUX G
94 CN1802
DVDD2 X602 KEY MATRIX
121 4.7186MHz
DVDD4 51 S1803 S1805
BU_X2
AUX-G AUX G S1801 S1802 S1804 S1806 S1807
6 6
5 PAUSE LEFT DOWN 3
AUX-L
7 7
AUX L
E
16 S1810 S1812
CDRESET S1809 S1811 S1813 S1814 S1815
34 DSENS DSENS
DSENS 14 14 D1803-D1810 EQ UP RIGHT BAND 2
D1812-D1823
ILMPW D1825
Q821
ILM+B ILL+B S1816 S1817 S1819 S1820 S1821
B.UP 9 9 6 AUDIO CLK 1 4
Q822
B.UP
2
ILMPW
SWVDD S1822 S1824
SWD5V 3 3 SWVDD EJECT FUNC
S1830
126
VDCONT 33 SOURCE SRC
SRC 4 4
SOURCE
S1831
111 ROT1 ROT1 1
ROT1 10 10
DEH-1950/XU/CN5
5 6 7 8
13
1 2 3 4
A-a A-b
Large size
SCH diagram
A-a
C CN702
A-a A-b Guide page
1K
1K
C
ROT1
CE2
ROMDATA ROT0
C402
R01
C637
R01
SELFOUT
VST
VDT
VCK
VDCONT
FLMD1
D KEYD
SYSTEM CONTROLLER
SL
MODELAD
KEYAD
SYSPW
R855
100K
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor. 2.2 2R2
No differentiation is made between chip capacitors and 0.022 R022
discrete capacitors.
B
The > mark found on some component parts indicates CN1801
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
A
D832
FTZ6R8E
DEH-1950/XU/CN5
14
1 2 3 4
5 6 7 8
A
A-b
REAR
OUTPUT
B
1K
1K
680
680
>
R648
C637
R01
>
10A
A
DEH-1950/XU/CN5
5 6 7 8
15
F
E
B
A
D
C
16
A-a A-b
A-b
1
1
REAR
OUTPUT
2
2
1K
1K
680
680
>
DEH-1950/XU/CN5
2
3
3
R648
4
4
R01
C637
5 6 7 8
10A
>
A-a A-b
D
3 4 5 A-b
DEH-1950/XU/CN5
5 6 7 8
17
F
E
B
A
D
C
18
A-a A-b
A-a
A-b
1
1
C CN702 1
2
2
1K
1K
DEH-1950/XU/CN5
2
3
3
ROT1
CE2
ROMDATA ROT0
R01
4
C402
4
R01
C637
SELFOUT
VST
VDT
VCK
VDCONT
VST
VDT
VCK
VDCONT
FLMD1
KEYD
3
5
5
SYSTEM CONTROLLER
SL
MODELAD
KEYAD
SYSPW
6
6
100K
R855
4
NOTE :
DEH-1950/XU/CN5
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
7
7
D832
8
8
FTZ6R8E
A-a A-b
A-a
A-b
19
E
A
D
C
F
B
1 2 3 4
PAUSE
LCD DRIVER/
KEY CONTROLLER
B
DEH-1950/XU/CN5
20
1 2 3 4
5 6 7 8
B KEYBOARD UNIT
A
CN831 B
AUX
INPUT
PAUSE
B
DEH-1950/XU/CN5
5 6 7 8
21
1 2 3 4
A C CD CORE UNIT(S10.5)
C
S
PICKUP UNIT(P10.5)(SERVICE)
C
S
F %
T
F F
C F
F F
F T T
T
T T
@
M1 CXC7134
SPINDLE MOTOR
S
C
D
M2 CXC4026
LOADING/CARRIAGE MOTOR
SWITCHES:
CD CORE UNIT(S10.5)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF CD DRIVER
S905:8EJ SWITCH...............ON-OFF $
T S
9 7
C
F
E 8
0 4
T
C
C
S
S
C
DEH-1950/XU/CN5
22
1 2 3 4
5 6 7 8
SIGNAL LINE A
F
FOCUS SERVO LINE
T
C
S
F
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
B
C
S
CD DSP
A CN651
^
&
C
DEH-1950/XU/CN5
5 6 7 8
23
1 2 3 4
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 5 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 4 LOEJ 5 V/div 3 12SNS 5 V/div
4 LOEJ 5 V/div 6 VD 10 V/div 4 LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation
7 SIN 1 V/div 2 s/div 0 FIN 200 mV/div 500 ms/div @ TE 500 mV/div 200 ms/div
8 CIN 500 mV/div ! RFOK # FE 500 mV/div
9 TIN 500 mV/div (MONI_2) 2 V/div
7 SIN 2 V/div
12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation
0 FIN 500 mV/div 200 ms/div @ TE 500 mV/div 2 ms/div % RFAGC 1 V/div 500 s/div
# FE 500 mV/div % RFAGC 500 mV/div @ TE 500 mV/div
E
9 TIN 500 mV/div
DEH-1950/XU/CN5
24
1 2 3 4
5 6 7 8
% RFAGC 1 V/div 500 s/div % RFAGC 1 V/div 1 ms/div % RFAGC 1 V/div 2 ms/div
@ TE 500 mV/div @ TE 500 mV/div @ TE 500 mV/div A
9 TIN 500 mV/div 9 TIN 500 mV/div 9 TIN 500 mV/div
% RFAGC 1 V/div 200 ms/div ^ LOUT 1 V/div 200 s/div 1 DSCSNS 5 V/div 500 ms/div
@ TE 1 V/div & ROUT 1 V/div 2 8SNS 5 V/div
8 CIN 500 mV/div 3 12SNS 5 V/div
7 SIN 2 V/div 4 LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div % RFAGC 1 V/div 500 s/div
5 CLCONT 5 V/div 2 8SNS 5 V/div 9 TIN 1 V/div
4 LOEJ 5 V/div 3 12SNS 5 V/div @ TE 1 V/div
4 LOEJ 5 V/div 0 FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 m) during play
DEH-1950/XU/CN5
5 6 7 8
25
1 2 3 4
SIDE B
P.C.Board Chip Part
C
CN702
B
F
CN1801
A
DEH-1950/XU/CN5
26
1 2 3 4
5 6 7 8
SIDE A
Y
REAR OUTPUT
15
B
16 ANTENNA
F
FRONT
A
DEH-1950/XU/CN5
5 6 7 8
27
1 2 3 4
SCET
TESTIN
E
A
DEH-1950/XU/CN5
28
1 2 3 4
5 6 7 8
SIDE B
A
DEH-1950/XU/CN5
5 6 7 8
29
1 2 3 4
AUDIO
FUNCTION
EJECT
INPUT
B
AUX
EQ
PAUSE
6
C
5
4
3
D
2
A CN831
1
CLOCK
E
VOLUME
SOURCE
BAND
B
DEH-1950/XU/CN5
30
1 2 3 4
5 6 7 8
DEH-1950/XU/CN5
5 6 7 8
31
1 2 3 4
E
M2
LOADING
/CARRIAGE
MOTOR
M1
SPINDLE
MOTOR
C
DEH-1950/XU/CN5
32
1 2 3 4
5 6 7 8
C
DEH-1950/XU/CN5
5 6 7 8
33
1 2 3 4
A
Unit Number : CWN2131
L
L
611
612
(B,134,79)
(B,132,79)
Inductor
Inductor
CTF1379
CTF1379
L 613 (B,143,58) Inductor CTF1379
Unit Name : Tuner Amp Unit L 614 (B,120,64) Inductor CTF1379
L 615 (B,150,71) Inductor CTF1379
D
MISCELLANEOUS
L 616 (B,142,75) Inductor CTF1379
IC 151 (B,121,99) IC PML014A L 617 (B,145,50) Inductor CTF1389
IC 301 (A,92,131) IC PAL007C L 801 (A,71,22) Inductor LAU2R2K
IC 601 (B,126,41) IC PN5010A L 901 (A,34,96) Choke Coil 600 H CTH1291
IC 911 (A,20,78) IC BA4918-V12 X 601 (A,140,60) Crystal 74.100 MHz CSS1728
Q 201 (B,127,127) Transistor UMD2N
X 602 (A,112,56) Crystal 4.718 6 MHz CSS1727
Q 351 (B,159,125) Transistor UMH3N >FU351 (B,132,130) Fuse 3 A CEK1286
Q 601 (A,149,64) Transistor 2SD1858 AR401 (B,162,108) Surge Protector IMSA-6801-01Y901
Q 821 (B,29,10) Transistor 2SA1036K > Fuse 10 A CEK1208
Q 822 (B,20,9) Transistor DTC114EUA FM/AM Tuner Unit CWE2025
Q 931 (B,57,95) Transistor 2SC2412K
E RESISTORS
Q 991 (A,6,113) Transistor 2SD2396
Q 992 (B,11,103) Transistor UMD2N R 151 (B,87,93) RAB4C102J
D 301 (A,64,121) Diode MPG06G-6415G3 R 156 (B,88,86) RS1/16S681J
D 302 (A,52,121) Diode MPG06G-6415G3 R 157 (B,92,86) RS1/16S681J
D 832 (B,73,5) Diode FTZ6R8E R 162 (B,137,99) RS1/16S102J
R 163 (B,103,104) RS1/16S102J
D 901 (A,47,107) Diode MPG06G-6415G3
D 902 (A,47,104) Diode MPG06G-6415G3 R 201 (B,123,127) RS1/16S103J
D 911 (A,49,78) Diode MPG06G-6415G3 R 202 (B,129,131) RS1/16S153J
D 912 (A,43,78) Diode MPG06G-6415G3 R 203 (B,123,129) RS1/16S221J
D 931 (A,63,106) Diode HZS7L(A1) R 251 (B,101,104) RS1/16S223J
R 252 (B,135,99) RS1/16S223J
F D 991 (A,17,110) Diode HZS7L(C3)
L 151 (A,135,103) Inductor LAU2R2K R 301 (B,93,105) RS1/16S153J
L 401 (A,147,79) Inductor LAU2R2K R 351 (B,163,128) RS1/16S223J
L 402 (A,143,96) Inductor LAU2R2K R 352 (B,163,132) RS1/16S223J
DEH-1950/XU/CN5
34
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 353 (B,145,115) RS1/16S821J R 839 (A,86,12) RD1/4PU222J
R 354 (B,163,124) RS1/16S821J R 840 (A,84,12) RD1/4PU222J
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
S 905 (B,25,68) Switch(8EJ) CSN1068 C 223 (A,46,54) CCSSCH680J50
C 224 (A,44,56) CCSSCH470J50
RESISTORS
C 225 (A,44,60) CKSSYB103K16 A
R 101 (B,57,73) RS1/10SR2R4J C 229 (B,46,55) CKSSYB104K10
R 102 (B,60,73) RS1/10SR2R4J C 231 (B,33,32) CKSSYB102K50
R 103 (B,60,70) RS1/10SR2R7J C 232 (B,32,29) CKSSYB102K50
R 105 (B,14,26) RS1/16SS102J C 233 (B,26,51) CKSSYB103K16
R 106 (B,15,26) RS1/16SS473J
C 236 (B,38,54) CKSSYB104K10
R 108 (B,58,64) RS1/16SS105J C 238 (A,34,66) CKSRYB104K10
R 109 (B,44,59) RS1/16SS102J C 240 (A,34,64) CKSRYB104K10
R 214 (A,43,41) RS1/16SS332J C 304 (A,35,19) CKSSYB472K25
R 215 (A,42,40) RS1/16SS183J C 305 (A,36,22) CKSSYB223K16
R 216 (A,45,48) RS1/16SS122J
C 306 (A,21,10) CKSRYB105K10
C 705 (B,9,34) CCSSCH101J50 B
R 217 (A,47,45) RS1/16SS562J
R 218 (A,47,48) RS1/16SS472J C 710 (B,10,32) CKSSYB102K50
R 232 (A,24,59) RS1/16SS0R0J
R 235 (A,36,30) RS1/16SS103J Miscellaneous Parts List
R 236 (A,36,29) RS1/16SS103J
Pickup Unit(P10.5)(Service) CXX1942
R 237 (B,24,47) RS1/16SS221J M 1 Motor Unit(SPINDLE) CXC7134
R 240 (B,20,44) RS1/16SS473J M 2 Motor Unit(LOADING/CARRIAGE) CXC4026
R 242 (A,28,32) RS1/16SS103J
R 243 (A,27,32) RS1/16SS473J
R 245 (B,23,49) RS1/16SS104J
CAPACITORS
DEH-1950/XU/CN5
5 6 7 8
37
1 2 3 4
6. ADJUSTMENT
6.1 CD ADJUSTMENT
A
DEH-1950/XU/CN5
38
1 2 3 4
5 6 7 8
- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In
Display
A
[CD] or [SOURCE]
Source On
[BAND] [2]
Power Off Tracking Open
*) After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
F
When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
DEH-1950/XU/CN5
5 6 7 8
39
1 2 3 4
Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
B Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT(S10.5)
C F
E REFO1 L.P.F.
Xch Ych
E 100 k
Oscilloscope
VREF 390 pF
F 100 k
VREF 390 pF
D L.P.F.
Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the and buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75 . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-1950/XU/CN5
40
1 2 3 4
5 6 7 8
0 30
45 60
75 90
DEH-1950/XU/CN5
5 6 7 8
41
1 2 3 4
DEH-1950/XU/CN5
42
1 2 3 4
5 6 7 8
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled),
shift the TESTIN IC601(Pin 112) terminal to H. The clock signal is output from the SCET IC601(Pin 43) terminal.
The frequency of the clock signal is 1 Hz. The clock signal should be 1 Hz 0.000 04 Hz.
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.
DEH-1950/XU/CN5
5 6 7 8
43
1 2 3 4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A
4
4 Remove the two screws and then remove
the Tuner Amp Unit.
4
1
E
3
3
DEH-1950/XU/CN5
44
1 2 3 4
5 6 7 8
B
B
A
Damper
Damper D
A
Carriage Mechanism Lower Frame
DEH-1950/XU/CN5
5 6 7 8
45
1 2 3 4
Screw
B
CD Core Unit
Solder
Planet Gear
Pickup Rack
Chassis
Pickup
DEH-1950/XU/CN5
46
1 2 3 4
5 6 7 8
7.1.2 CONNECTOR FUNCTION DESCRIPTION
16141210 8 6 4 2
151311 9 7 5 3 1
7 NC 15 RR+
8 NC 16 FR+
DEH-1950/XU/CN5
5 6 7 8
47
F
E
B
A
D
C
48
DATA
STB
Vcc
GND
CLK
Vref
7.2.1 IC
PML014A
1
1
IN4+_L
- Block Diagram
Isolator
IN4-_L Gain Auto Primary
Adjuster Zero
IN4-_R Volume
Isolator
Input Selector
IN4+_R
Secondary
IN3_R Front_L
IN2_R Volume
IN1_R Anti-Alias
Filter
Secondary
Rear_L
2
2
Volume
Anti-Radiation
TRE MID BASS LOUDNESS
Filter
Secondary
Front_R
Volume
Secondary
DEH-1950/XU/CN5
Rear_R
Volume
3
3
Vcc
GND
Vref
Rear_L
Front_L
IN4-_L
IN4+_L
IN3_L
IN2_L
IN1_L
9
8
7
6
5
4
3
2
1
10
- Pin Layout
4
4
11
12
13
14
15
16
17
18
19
20
CLK
STB
DATA
IN3_R
IN2_R
IN1_R
IN4-_R
IN4+_R
Rear_R
Front_R
5 6 7 8
PAL007C
sw_vcc
Protector;
Over voltage
1
TAB Reference
amp_vcc
Stand-by
2
P-GND2 Circuit
+-
3
OUT2-
Offset Protector;
4
STBY Detection Thermal
-+
5
OUT2+
B
6
VCC
+-
7
OUT1-
Offset
8
P-GND1 Detection
-+
9
OUT1+
10
SVR
11
IN1
12 13
IN2
amp_vcc
Protector;
S-GND Short circuit
C
14
IN4
15
IN3
16
AC-GND
17
+-
OUT3+
18
Offset
P-GND3 Detection
19
-+
OUT3-
20 21
VCC
D
+-
OUT4+
22
Offset
MUTE Detection
23
-+
OUT4-
24 25
P-GND4
SWITCH
sw_vcc
stby
Protector;
Over current limit
Mute circuit
DEH-1950/XU/CN5
5 6 7 8
49
1 2 3 4
DEH-1950/XU/CN5
50
1 2 3 4
5 6 7 8
DEH-1950/XU/CN5
5 6 7 8
51
1 2 3 4
PN5010A
Format Meaning
108
73
C CMOS
109 72 N Nch open drain
144 37
1
36
BA4918-V12
- Block Diagram - Pin Layout
12 GND
+B 10 9 +BUP
11 NC
Overvoltage Overvoltage
C Protection Protection 10 +B
(OFF except VDD) Pre Reg
(All Ourput OFF) 9 +BUP
8 VDD
TSD Vref 7 SYS+B
6 SWVDD
5 SW5V
4 SW5VCONT
8 VDD 3 SYSPW
2 BSENS
+B
SW5VCONT 4 1 VDDCONT
D
5 SW5V
+B
SYSPW 3
7 SYS+B
+B
VDDCONT 1
E
6 SWVDD
+B
VDD
2 BSENS
Reduced-voltage
Detection
GND 12 +B
VDD
F
Overvoltage Detection
DEH-1950/XU/CN5
52
1 2 3 4
5 6 7 8
- Pin Functions(PD6340A)
Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output
6-9 COM3-0 O LCD common output A
10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output
15,16 KDT0,1 I Key data input (analogue input)
17 REW I Remote control reception input
18 DPDT I Display data input
19 NC Not used
20 KYDT O Key data output
21 MODA GND
22 X0 Crystal oscillator connection pin
23 X1 Crystal oscillator connection pin
24 VSS GND
B
25,26 KDT2,3 I Key data input
27 NC Not used
28 KST4 O Key strobe output
29-32 NC Not used
33-55 SEG35-13 O LCD segment output
56 VDD Power supply
57-64 SEG12-5 O LCD segment output
PD6340A
1
16
64 17 C
49 32
48
33
DEH-1950/XU/CN5
5 6 7 8
53
1 2 3 4
DEH-1950/XU/CN5
54
1 2 3 4
5 6 7 8
PE5497B
100
76
1 75
D
25 51
26
50
DEH-1950/XU/CN5
5 6 7 8
55
1 2 3 4
- Pin Functions(BA5839FP)
Pin No. Pin Name Function and Operation
1 VR Input pin for reference voltage
A
2 OPIN2(+) Input pin for non-inverting input for CH2 preamplifier
3 OPIN2(-) Input pin for inverting input for CH2 preamplifier
4 OPOUT2 Output pin for CH2 preamplifier
5 OPIN1(+) Input pin for non-inverting input for CH1 preamplifier
6 OPIN1(-) Input pin for inverting input from CH1 preamplifier
7 OPOUT1 Output pin for CH1 preamplifier
8 GND Ground pin
9 MUTE Mute control pin
10 POWVCC1 Power supply pin for CH1, CH2, and CH3 at "Power" stage
11 VO1(-) Driver CH1 - Negative output
12 VO1(+) Driver CH2 - Positive output
B 13 VO2(-) Driver CH2 - Negative output
14 VO2(+) Driver CH2 - Positive output
15 VO3(+) Driver CH2 - Positive output
16 VO3(-) Driver CH2 - Negative output
17 VO4(+) Driver CH4 - Positive output
18 VO4(-) Driver CH4 - Negative output
19 POWVCC2 Power supply pin for CH4 at "Power" stage
20 GND Ground pin
21 CNT Control pin
22 LDIN Loading input
23 OPOUTSL Output pin for preamplifier for thread
24 OPINLSL Input pin for preamplifier for thread
C 25 OPOUT3 CH3 preamplifier output pin
26 OPIN3(-) Input pin for inverting input for CH3 preamplifier
27 OPIN3(+) Input pin for non-inverting input for CH3 preamplifier
28 PREVCC PreVcc
BA5839FP
14 1
15 28
DEH-1950/XU/CN5
56
1 2 3 4
5 6 7 8
RFGND1
RFGND2
RFGND3
RFGND4
IFOUTB
IFOUTA
SLOUT
RFINA
RFINB
DGND
LDET
SLIN
VCC
VDD
ANT
CE1
CE2
DO
A
CK
DI
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
IC2
EEPROM
VCO LFP
B
ATT
ATT
TANK
IC1
MIX / IF / PLL
ATT RF LFP
CF
No. Symbol
y I/O Explain
1 ANT I Antenna Input Antenna input. 75 . Surge absorber is necessary. C
Series circuit including an inductor and a resistor is connected with RF
ground for the countermeasure against the ham of power transmission line.
2 RFGND1 RF Ground Ground of R.F. block
3 RFGND2 RF Ground Ground of R.F. block
4 RFGND3 RF Ground Ground of R.F. block
5 RFGND4 RF Ground Ground of R.F. block
6 VCC Power Supply Power supply for Analog block. D.C 8.4 V 0.3 V
(performance isn't guaranteed besides 8.4 V)
7 SLIN I Signal
g Level Input Input signa
g level from BE_IC
8 IFOUTA O IF Output IF signal output (F.E.output)
9 IFOUTB O IF Output IF signal
g output ((F.E.output)) D
10 DGND Digital Ground Ground of Digital. block
11 REFINA I Reference Signal Input reference signal for PLL part with FE_IC
12 REFINB I Reference Signal Input reference signal for PLL part with FE_IC
13 LDET O Lock Detector PLL lock detecter output "High" active
14 VDD Power Supply Power supply for Digital block. D.C 3.3 V 0.2 V
15 DI I Data In Data input (not sending data in tuner reception operating in noise
being output)
16 CK I CK Clock data input(not sending data in tuner reception operating in noise
being output)
17 CE1 I Chip Enable-1 Chip enable for FE_IC "High" active
E
18 DO O Data Out Data output
19 CE2 O Chip Enable-2 Chip enable for EEPROM "Low" active. in power ON/OFF, please turn CE2
into "High" (= VDD).
20 SLOUT O Signal Level Output Output of FM/AM signals level (D.C.)
DEH-1950/XU/CN5
5 6 7 8
57
1 2 3 4
7.2.2 DISPLAY
- LCD(CAW1931)
A
E
SEGMENT
COMMON
DEH-1950/XU/CN5
58
1 2 3 4
5 6 7 8
A
Power ON
VDD
Pin 8
bsens
B
Pin 36
bsens = L
asens
Pin 35
asens = L
300 ms
SWVDDH
Pin 1
300 ms
Source ON
SYSPWH
Pin 15
E
Completes power-on operation.(After that, proceed to each source operation.)
DEH-1950/XU/CN5
5 6 7 8
59
1 2 3 4
8. OPERATIONS
DEH-1950/XU/CN5
60
1 2 3 4
5 6 7 8
(CXX2204)
DEH-1950/XU/CN5
5 6 7 8
61
1 2 3 4
DEH-1950/XU/CN5
62
1 2 3 4
5 6 7 8
DEH-1950/XU/CN5
5 6 7 8
63
1 2 3 4
- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking
g the g
grating
g
L.P.F. Checking
g the g
grating
g ((Two pieces))
- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
B Grease GEM1045 CD Mechanism Module
DEH-1950/XU/CN5
64
1 2 3 4