Professional Documents
Culture Documents
Quick-Reference Reset Guide: For Reference Use Only
Quick-Reference Reset Guide: For Reference Use Only
RESET
GUIDE
FOR REFERENCE USE ONLY
The data contained herein is intended to assist troubleshooting
only and is not a substitute for Embraer and/or operators
manuals. Fault correcting maintenance and the aircrafts return
to service testing shall be accomplished in full accordance with
proper Embraer and/or operators manuals.
JANUARY 2006
REVISION 10 May 2010
Copyright 2010 by EMBRAER - Empresa Brasileira de Aeronutica S.A. All rights reserved. This
document shall not be copied or reproduced, whether in whole or in part, in any form or by any means
without the express written authorization of Embraer. The information, technical data, designs and
drawings disclosed in this document are property information of Embraer or third parties and shall not be
used or disclosed to any third party without permission of Embraer.
TABLE OF CONTENTS
INTRODUCTION ......................................................................... 8
MAU AND SPDA RESET SAFETY PROCEDURES ................. 10
GENERAL INFORMATION ....................................................... 15
ACARS FROZEN ...................................................................... 16
ADS 1 FAIL............................................................................... 17
ADS 1 HTR FAIL ...................................................................... 17
ADS 1 HTR FAULT................................................................... 18
ADS 2 FAIL............................................................................... 18
ADS 2 HTR FAIL ...................................................................... 19
ADS 2 HTR FAULT................................................................... 20
ADS 3 FAIL............................................................................... 21
ADS 3 FAIL............................................................................... 22
ADS 3 SLIPCOMP FAIL ........................................................... 23
ADS 4 HTR FAIL ...................................................................... 24
ADS 4 SLIPCOMP FAIL ........................................................... 25
ADS PROBE 1 FAIL ................................................................. 26
ADS PROBE 2 FAIL ................................................................. 27
ADS PROBE 3 FAIL ................................................................. 28
ADS PROBE 4 FAIL ................................................................. 29
AFCS FAULT............................................................................ 30
A-I ENG 1 FAULT ..................................................................... 31
A-I ENG 2 FAULT ..................................................................... 32
A-I WING FAIL.......................................................................... 33
AMBER "X" ON RECIRC FAN INDICATION
(ECS SYNOPTIC PAGE) .......................................................... 34
AOA LIMIT FAIL ....................................................................... 35
APPR 2 NOT AVAIL ................................................................. 35
APU FAIL.................................................................................. 36
APU FUEL SOV FAIL ............................................................... 36
AT FAIL .................................................................................... 37
AURAL WRN SYS FAIL ........................................................... 38
AURAL WRN SYS FAULT........................................................ 38
AUTOBRAKE FAIL................................................................... 39
AVNX MAU 1A FAIL ................................................................. 39
AVNX MAU 1A FAULT ............................................................. 40
AVNX MAU 1B FAIL ................................................................. 41
AVNX MAU 1B FAULT ............................................................. 42
AVNX MAU 2A FAIL ................................................................. 43
Page 2 May 10
AVNX MAU 2A FAULT .............................................................44
AVNX MAU 2B FAIL .................................................................45
AVNX MAU 2B FAULT .............................................................46
AVNX MAU 3A FAIL .................................................................47
AVNX MAU 3A FAULT .............................................................48
AVNX MAU 3B FAIL .................................................................49
AVNX MAU 3B FAULT .............................................................50
BLEED 1 FAIL...........................................................................51
BLEED 1 OFF ...........................................................................52
BLEED 2 FAIL...........................................................................53
BLEED 2 OFF ...........................................................................54
BRK CONTROL FAULT............................................................55
BRK LH FAULT ........................................................................55
BRK LH FAULT ........................................................................56
CAS MSG INDICATION ON PFD ..............................................56
CENTER EBAY FANS FAIL......................................................57
CHIMES NOT AVAILABLE - ALL POSITIONS .........................58
CMF 1 FAIL...............................................................................58
"CMC IN AIR" OR "CMC CONNECTION FAILED"
MESSAGES ON CMC SCREEN ...............................................59
COPILOT DAP PROBLEMS - DISPLAY, VOLUME AND
CONTROLS ..............................................................................60
CVR AFT FAIL ..........................................................................60
CVR FWD FAIL .........................................................................61
DATALINK TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD..........................................................................61
DATALINK TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD..........................................................................62
EICAS FAULT ...........................................................................62
ELEVATOR FAULT...................................................................63
ELEVATOR LH FAIL.................................................................63
ELEVATOR RH FAIL ................................................................64
ENG 1 FADEC FAULT ..............................................................65
ENG 1 FUEL SW FAIL .............................................................66
ENG 2 FADEC FAULT ..............................................................67
ENG 2 FUEL SW FAIL .............................................................68
ENG TLA TRIM FAIL ................................................................69
FDR AFT FAIL ..........................................................................70
FDR FWD FAIL .........................................................................70
FLAP FAIL ................................................................................71
Page 3 May 10
FLAP LO RATE ........................................................................ 72
FLT CTRL BIT EXPIRED .......................................................... 73
FLT CTRL FAULT..................................................................... 74
FLT CTRL NO DISPATCH ........................................................ 75
FLT CTRL NO DISPATCH/FLT CTRL FAULT/FLT CTRL BIT
EXPIRED, AUTO CONFIG TRIM FAIL (ALTERNATE
PROCEDURE) .......................................................................... 76
FMS 1 FAIL............................................................................... 77
FMS 2 FAIL............................................................................... 78
FMS1 TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD ......................................................................... 79
FMS1-2 TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD ......................................................................... 80
FMS1-2 TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD ......................................................................... 81
FMS2 TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD ......................................................................... 82
FUEL DC PUMP FAIL............................................................... 83
FUEL EQUAL-XFEED OPEN.................................................... 83
FWD EBAY FANS FAIL............................................................ 84
GND PROX FAIL ...................................................................... 85
GROUND SPOILERS FAIL....................................................... 86
HUD 1 FAIL .............................................................................. 86
HUD 2 FAIL .............................................................................. 87
HUD FAIL ................................................................................. 88
ICE DETECTOR 1 FAIL ............................................................ 89
ICE DETECTOR 2 FAIL ............................................................ 90
INPH AUDIO (BETWEEN DAPS) - NOISY
OR NOT AVAILABLE ............................................................... 91
INVERTER FAIL ....................................................................... 91
IRS 1 FAIL ................................................................................ 92
IRS 2 FAIL ................................................................................ 92
IRS PRES POS INVALID .......................................................... 93
LAV SMOKE ............................................................................. 94
LAV SMOKE DET FAIL ............................................................ 95
LG NO DISPATCH.................................................................... 96
LG NOSE DOOR OPEN............................................................ 96
LG WOW SYS FAIL.................................................................. 97
MFD 1 FAULT........................................................................... 97
MFD 2 FAULT........................................................................... 98
Page 4 May 10
NAVCOM 1 FAIL.......................................................................98
NAVCOM 2 FAIL.......................................................................99
NO LEFT FUEL QTY INDICATION ON EICAS .........................99
NO RIGHT FUEL QTY INDICATION ON EICAS .....................100
NO TOTAL FUEL QTY INDICATION ON EICAS ....................100
OBSERVER DAP PROBLEMS - DISPLAY,
VOLUME AND CONTROLS....................................................100
PACK 1 FAIL ..........................................................................101
PACK 2 FAIL ..........................................................................101
PFD 1 FAULT..........................................................................102
PFD 2 FAULT..........................................................................102
PILOT DAP PROBLEMS - DISPLAY, VOLUME AND
CONTROLS ............................................................................103
PITCH TRIM BKUP FL............................................................103
PITCH TRIM FAIL ...................................................................104
PITCH TRIM SW 1 FAIL..........................................................105
PITCH TRIM SW 2 FAIL..........................................................106
POTABLE WATER OR WASTE SYSTEM INOPERATIVE. ....107
PRESN AUTO FAIL ................................................................108
PRESN AUTO FAULT.............................................................109
PRESN MAN FAIL ..................................................................110
RADIOS TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD........................................................................111
RADIOS TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD........................................................................111
RALT 1 FAIL ...........................................................................112
RALT 2 FAIL ...........................................................................112
RAM AIR FAULT.....................................................................113
RAT FAIL ................................................................................114
RECIRC SMK DET FAIL .........................................................115
RECIRC SMOKE.....................................................................115
REFUEL PG TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD........................................................................116
REFUEL PG TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD........................................................................117
REMOTE CB TRIP ..................................................................118
RUDDER FAIL ........................................................................119
RUDDER FAULT.....................................................................119
SETUP PG TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD........................................................................120
Page 5 May 10
SETUP PG TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD ....................................................................... 120
SHAKER 1 FAIL ..................................................................... 121
SHAKER 2 FAIL ..................................................................... 122
SLAT FAIL .............................................................................. 123
SLAT LO RATE ...................................................................... 124
SLAT-FLAP LEVER DISAG.................................................... 125
SPDA FAIL ............................................................................. 125
SPDBRK LEVER DISAG ........................................................ 126
SPOILER FAULT .................................................................... 126
STEER FAIL ........................................................................... 126
STEER FAULT........................................................................ 127
TAT 1 FAIL ............................................................................. 127
TAT 2 FAIL ............................................................................. 127
TCAS FAIL ............................................................................. 128
TERRAIN FAIL ....................................................................... 129
TERRAIN NOT AVAILABLE................................................... 130
TEST PG TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD ....................................................................... 131
TEST PG TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD ....................................................................... 131
THRUST MGT TIMEOUT SHOWS ON THE MCDU 1
SCRATCHPAD ....................................................................... 132
THRUST MGT TIMEOUT SHOWS ON THE MCDU 2
SCRATCHPAD ....................................................................... 133
TRU 1 FAIL ............................................................................. 134
TRU 2 FAIL ............................................................................. 134
TRU ESS FAIL........................................................................ 135
UNCOMMANDED CHIME GENERATION ALL
POSITIONS............................................................................. 135
UNCOMMANDED HF COMM TRANSMISSION ALL
POSITIONS............................................................................. 136
UNCOMMANDED VHF COMM 1 TRANSMISSION - ALL
POSITIONS............................................................................. 136
UNCOMMANDED VHF COMM 2 TRANSMISSION - ALL
POSITIONS............................................................................. 137
UNCOMMANDED VHF COMM 3 TRANSMISSION - ALL
POSITIONS............................................................................. 137
WATER SYSTEM FAULT INDICATION ON AFT FLIGHT
ATTENDANT PANEL ............................................................. 138
Page 6 May 10
WINDSHEAR FAIL..................................................................139
WINDSHIELD 1 HTR FAIL ......................................................140
WINDSHIELD 2 HTR FAIL ......................................................140
WX FAIL MESSAGE ON THE MFD ........................................141
XPDR 1 FAIL...........................................................................142
XPDR 2 FAIL...........................................................................142
Page 7 May 10
INTRODUCTION
This guide does not cover all the messages/faults that may be
detected on the aircraft. If the message/fault is not given in the
quick-reference guide, refer to the FAULT ISOLATION MANUAL.
Page 8 May 10
(b) If there are no correlated CMC messages go
directly to the task given in the GO TO FIM
TASK column.
If you have any doubts about how to use the FIM, refer to FAULT
ISOLATION MANUAL USAGE section.
Page 9 May 10
MAU and SPDA RESET SAFETY PROCEDURES
(2) If the aircraft is energized with APU and you open the
circuit breaker MAU 3 PWR 1, the APU will shutdown.
Page 10 May 10
(7) This procedure must be done to prevent the integrated
pitot/static/AOA and TAT system heating in any of these
situations:
(a) Open this circuit breaker and put a circuit breaker ring
and tag (inoperative - do not operate) on it:
Page 11 May 10
(c) Open these circuit breakers and put a circuit breaker
ring and tag (inoperative - do not operate) on each one of
them:
Page 12 May 10
SPDA - MAINTENANCE SAFETY PROCEDURES
Page 13 May 10
PROBE 3 HEATER PWR-RHCBP (DC ESS BUS 3
NAV)
ADS PROBE 1 HTR-LICC (DC BUS 1)
ADS PROBE 2 HTR-LICC (DC BUS1)
ADS PROBE 4 HTR-RICC (DC BUS 2)
Page 14 May 10
General Information
Page 15 May 10
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE:
Yes.
CAUTION: MAKE SURE THAT THE INTEGRATED
FIM TASK 23-24-00-810-
PITOT/STATIC/AOA SENSORS, TAT SENSORS, ICE
868-A
DETECTORS, AND STATIC PORT HAVE NO COVERS ON THEM
ACARS
23 BEFORE YOU DO THE MAINTENANCE PROCEDURE. THESE
FROZEN No.
COMPONENTS CAN BECOME HOT DURING THE
Refer to the correspondent
MAINTENANCE PROCEDURE. AS A RESULT, DAMAGE TO
chapter of the FIM for
THEM WILL OCCUR IF YOU DO NOT REMOVE THE COVERS.
troubleshooting.
Open this circuit breaker and, after approximately 5 seconds, close
it:
MAU 3 PWR 2-RHCBP (DC BUS 2)
May 10 Page 16
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 34-15-00-810-
Open these circuit breakers and, after approximately 5 seconds, 825-A
close them:
34 ADS 1 FAIL ADS 1 PROBE 1A-2A-LHCBP (DC BUS 1 NAV) No.
ADS FC PROBE 1B-2B-LHCBP (DC BUS 1 NAV) Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FAULT CONDITION: During power-up FIM TASK 34-15-00-810-
825-A
ADS 1 HTR PROCEDURE: Open these circuit breakers and, after 30 seconds,
30
FAIL close them: No.
ADS 1 PROBE 1A-2A-LHCBP (DC BUS 1/NAV) Refer to the correspondent
ADS FC PROBE 1B-2B-LHCBP (DC BUS 1/NAV) chapter of the FIM for
troubleshooting.
May 10 Page 17
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FAULT CONDITION: During power-up FIM TASK 34-15-00-810-
825-A
ADS 1 HTR PROCEDURE: Open these circuit breakers and, after 30 seconds,
30
FAULT close them: No.
ADS 1 PROBE 1A-2A-LHCBP (DC BUS 1/NAV) Refer to the correspondent
ADS FC PROBE 1B-2B-LHCBP (DC BUS 1/NAV) chapter of the FIM for
troubleshooting.
EFF: [ON ACFT WITH ADS 3/STBY PROBE 3B CIRCUIT
BREAKER ON DC ESS BUS 2]
May 10 Page 19
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 20
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 21
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 22
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 23
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 24
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 25
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH PRIMUS EPIC LOAD UP TO 21.5]
Yes.
FAULT CONDITION 1: The CAS message shows from the moment FIM TASK 34-15-00-810-
in which the aircraft is at the gate until the takeoff. ADS 1 FAIL does 852-A
not show on the EICAS display. No.
PROCEDURE: De-energize the aircraft and energize it again. Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
EFF: [ON ACFT WITH PRIMUS EPIC LOAD 23.1 AND ON] FIM TASK 34-15-00-810-
FAULT CONDITION: The CAS message shows as soon as the 801-A
aircraft lands. No.
PROCEDURE: Open these circuit breakers and, after Refer to the correspondent
approximately 5 seconds, close them: chapter of the FIM for
ADS 1 PROBE 1A-2A-LHCBP (DC BUS 1 NAV) troubleshooting.
ADS FC PROBE 1B-2B-LHCBP (DC BUS 1 NAV)
May 10 Page 26
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH PRIMUS EPIC LOAD UP TO 21.5]
Yes.
FAULT CONDITION 1: The CAS message shows from the moment FIM TASK 34-15-00-810-
in which the aircraft is at the gate until the takeoff. ADS 1 FAIL does 853-A
not show on the EICAS display. No.
PROCEDURE: De-energize the aircraft and energize it again. Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
EFF: [ON ACFT WITH PRIMUS EPIC LOAD 23.1 AND ON] FIM TASK 34-15-00-810-
FAULT CONDITION: The CAS message shows as soon as the 801-A
aircraft lands. No.
PROCEDURE: Open these circuit breakers and, after Refer to the correspondent
approximately 5 seconds, close them: chapter of the FIM for
ADS 1 PROBE 1A-2A-LHCBP (DC BUS 1 NAV) troubleshooting.
ADS FC PROBE 1B-2B-LHCBP (DC BUS 1 NAV)
May 10 Page 27
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH PRIMUS EPIC LOAD UP TO 21.5] Yes.
FAULT CONDITION 1: The CAS message shows from the moment in which the FIM TASK 34-15-00-810-854-A
aircraft is at the gate until the takeoff. ADS 2 FAIL and ADS 3 FAIL do not show on the No.
EICAS display. Refer to the correspondent
PROCEDURE: De-energize the aircraft and energize it again. chapter of the FIM for
FAULT CONDITION 2: The CAS message shows as soon as the aircraft lands. troubleshooting.
EFF: [ON ACFT WITH ADS 3/STBY PROBE 3B CIRCUIT BREAKER ON DC ESS
BUS 2]
PROCEDURE: Open these circuit breakers and, after approximately 5 seconds, close
them:
ADS 2 PROBE 3A-RHCBP (DC ESS BUS 3 NAV)
ADS 3/STBY PROBE 3B-RHCBP (DC ESS BUS 2 NAV)
Yes.
EFF: [ON ACFT WITH ADS 3/STBY PROBE 3B CIRCUIT BREAKER ON DC ESS FIM TASK 34-15-00-810-806-A
BUS 3] No.
PROCEDURE: Open these circuit breakers and, after approximately 5 seconds, close Refer to the correspondent
ADS PROBE 3 them: chapter of the FIM for
34 ADS 2 PROBE 3A-RHCBP (DC ESS BUS 3 NAV) troubleshooting.
FAIL ADS 3/STBY PROBE 3B-RHCBP (DC ESS BUS 3 NAV)
EFF: [ON ACFT WITH PRIMUS EPIC LOAD 23.1 AND ON]
FAULT CONDITION: The CAS message shows as soon as the aircraft lands.
EFF: [ON ACFT WITH ADS 3/STBY PROBE 3B CIRCUIT BREAKER ON DC ESS
BUS 2]
PROCEDURE: Open these circuit breakers and, after approximately 5 seconds, close
them:
ADS 2 PROBE 3A-RHCBP (DC ESS BUS 3 NAV) Yes.
ADS 3/STBY PROBE 3B-RHCBP (DC ESS BUS 2 NAV) FIM TASK 34-15-00-810-806-A
No.
EFF: [ON ACFT WITH ADS 3/STBY PROBE 3B CIRCUIT BREAKER ON DC ESS Refer to the correspondent
BUS 3] chapter of the FIM for
PROCEDURE: Open these circuit breakers and, after approximately 5 seconds, close troubleshooting.
them:
ADS 2 PROBE 3A-RHCBP (DC ESS BUS 3 NAV)
ADS 3/STBY PROBE 3B-RHCBP (DC ESS BUS 3 NAV)
May 10 Page 28
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH PRIMUS EPIC LOAD UP TO 21.5]
FAULT CONDITION 1: The CAS message shows from the moment Yes.
in which the aircraft is at the gate until the takeoff. ADS 2 FAIL and FIM TASK 34-15-00-810-
ADS 3 FAIL do not show on the EICAS display. 855-A
PROCEDURE: De-energize the aircraft and energize it again. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
FAULT CONDITION 2: The CAS message shows as soon as the
aircraft lands. Yes.
PROCEDURE: Open these circuit breakers and, after FIM TASK 34-15-00-810-
approximately 5 seconds, close them: 806-A
ADS PROBE 4 ADS 2 PROBE 4A-RHCBP (DC BUS 2 NAV) No.
34
FAIL ADS 3/STBY PROBE 4B-RHCBP (DC ESS BUS 2 NAV) Refer to the correspondent
chapter of the FIM for
troubleshooting.
EFF: [ON ACFT WITH PRIMUS EPIC LOAD 23.1 AND ON]
FAULT CONDITION: The CAS message shows as soon as the Yes.
aircraft lands. FIM TASK 34-15-00-810-
PROCEDURE: Open these circuit breakers and, after 806-A
approximately 5 seconds, close them: No.
ADS 2 PROBE 4A-RHCBP (DC BUS 2 NAV) Refer to the correspondent
ADS 3/STBY PROBE 4B-RHCBP (DC ESS BUS 2 NAV) chapter of the FIM for
troubleshooting.
May 10 Page 29
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 30
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 31
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 32
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
FAULT CONDITION: "A-I WING FAIL" CAS message shows during
the BIT (Built-in Test)
May 10 Page 33
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
AMBER "X" FAULT CONDITION: RECIRC switch is set to AUTO, batteries are Yes.
ON RECIRC set to ON/AUTO, and the GPU is OFF for more than one minute FIM TASK 21-24-00-810-
FAN 805.
PROCEDURE: On the overhead panel, on the AIR
21 INDICATION COND/PNEUMATIC control panel, set the RECIRC pushbutton to No.
(ECS the unlatched (off) position. Wait 60 seconds and set it back to the Refer to the correspondent
SYNOPTIC latched (auto) position. If it does not work, reset the aircraft (power chapter of the FIM for
PAGE) down/up). troubleshooting.
May 10 Page 34
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 27-03-00-810-
89L-A
AOA LIMIT On the maintenance panel, make sure the FCS MAINT switch is in
27
FAIL the OFF position. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 22-11-00-810-
981-A
Make sure that the same ADS and IRS sources are not selected on
APPR 2 NOT
22 PFD 1 and PFD 2, the indications of RALT/IRS/ADS/FD are correct
AVAIL and there are no messages related to these systems on the EICAS.
No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 35
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
On the MCDU, open these SSPCs and close them after 10 seconds FIM TASK 49-10-00-810-
to confirm that the failure has occurred: 801-A
APU FADEC (CB/CB BY SYS/APU)
49 APU FAIL ABC CMD PWR (CB/CB BY SYS/APU) No.
ASC CMD PWR (CB/CB BY SYS/APU) Refer to the correspondent
Start the APU again. chapter of the FIM for
troubleshooting.
May 10 Page 36
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
FAULT CONDITION 1: "ENG TLA TRIM FAIL" message is active on the EICAS; AND
FAULT CONDITION 2: The following maintenance messages are active on the CMC:
22310005TA1 - ENGINE DATA [TRSA1] FAULT
22310005TA2 - ENGINE DATA [TRSA2] FAULT
22310023TA1 - FADEC1/FADEC2 [ATA1] WRG FAULT
22310023TA2 - FADEC1/FADEC2 [ATA2] WRG FAULT
22310079TA1 - LEFT FADEC [ATA1] FAULT
22310079TA2 - LEFT FADEC [ATA2] FAULT
22310080TA1 - RIGHT FADEC [ATA1] FAULT
22310080TA2 - RIGHT FADEC [ATA2] FAULT
NOTE: The recording of "RIGHT FADEC [ATxx] FAULT" or "LEFT FADEC [ATxx] FAULT"
maintenance message on the CMC depends on the faulty FADEC. The left FADEC refers to Yes.
engine 1 and the right FADEC refers to engine 2. FIM TASK 22-31-00-810-
EFF: [ALL] 821-A
22 AT FAIL PROCEDURE: No.
On the CMC, use the sequence that follows to get access to the ENGINE 1 GENERAL
STATUS PAGE: Refer to the correspondent
73 - ENGINE FUEL AND CONTROL chapter of the FIM for
21 - ENGINE FADEC 1A
ENGINE 1 GENERAL STATUS PAGE troubleshooting.
If the CHANNEL IN CONTROL status is the same for both channels, go to the FIM TASK 22-
31-00-810-821-A.
On the CMC, use the sequence that follows to get access to the ENGINE 2 GENERAL
STATUS PAGE:
73 - ENGINE FUEL AND CONTROL
21 - ENGINE FADEC 2A
ENGINE 2 GENERAL STATUS PAGE
If the CHANNEL IN CONTROL status is the same for both channels, go to the FIM TASK 22-
31-00-810-821-A.
May 10 Page 37
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 38
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 32-41-00-810-
809-A
AUTOBRAKE On the CMC (System Diagnostics/ 32 - Landing Gear), run the
32
FAIL RESET TEST for AUTOBRAKE MODULE. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
CAUTION: MAKE SURE THAT THE INTEGRATED PITOT/STATIC/AOA
SENSORS, TAT SENSORS, ICE DETECTORS AND STATIC PORT HAVE
NO COVERS ON THEM BEFORE YOU DO THE MAINTENANCE
PROCEDURE. THESE COMPONENTS CAN BECOME HOT DURING THE
MAINTENANCE PROCEDURE. AS A RESULT, DAMAGE TO THEM WILL
OCCUR IF YOU DO NOT REMOVE THE COVERS.
Yes.
Open these circuit breakers and, after approximately 5 seconds, close them: FIM TASK 31-42-00-810-
NOTE: If power is removed from the CMC module for more than 10 seconds, 808-A
AVNX MAU 1A the CMC module will start its shutdown procedure. When power is supplied to
31 the CMC module again, it will start its power-up procedure. The full process
FAIL takes approximately 5 minutes. No.
MAU 1 PWR 1-LHCBP (DC ESS BUS 1) Refer to the correspondent
MAU 1 PWR 2-LHCBP (DC ESS BUS 1) chapter of the FIM for
MAU 1 PWR 3-LHCBP (DC BUS 1) troubleshooting.
On the CMC, use the sequence that follows to do the MAU 1 NIC module 1
reset test:
31 - INDICATING/RECORDING SYSTEMS
41 - MAU 1 NIC 1
MAU1_NIC1 MODULE RESET TEST
May 10 Page 39
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
On the CMC, use the sequence that follows to do the MAU 1 NIC
module 1 reset test:
31 - INDICATING/RECORDING SYSTEMS
41 - MAU 1 NIC 1
MAU1_NIC1 MODULE RESET TEST
May 10 Page 40
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
On the CMC, use the sequence that follows to do the MAU 1 NIC
module 1 reset test:
31 - INDICATING/RECORDING SYSTEMS
41 - MAU 1 NIC 2
MAU1_NIC2 MODULE RESET TEST
May 10 Page 41
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
On the CMC, use the sequence that follows to do the MAU 1 NIC
module 2 reset test:
31 - INDICATING/RECORDING SYSTEMS
41 - MAU 1 NIC 2
MAU1_NIC2 MODULE RESET TEST
May 10 Page 42
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH MAU2 PWR2 PRI CIRCUIT BREAKER ON
DC BUS 2]
EFF: ALL
May 10 Page 43
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH MAU2 PWR2 PRI CIRCUIT BREAKER ON
DC BUS 2]
EFF: ALL
May 10 Page 44
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH MAU2 PWR2 PRI CIRCUIT BREAKER ON
DC BUS 2]
EFF: ALL
May 10 Page 45
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH MAU2 PWR2 PRI CIRCUIT BREAKER ON
DC BUS 2]
EFF: ALL
May 10 Page 46
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 47
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 48
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 49
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 50
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 51
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 36-11-00-810-
FAULT CONDITION: The message BLEED 1 OFF comes into view
813A
on the EICAS.
36 BLEED 1 OFF No.
PROCEDURE: Make sure that the bleed 1 pushbutton is in the
Refer to the correspondent
AUTO position (pushed - light goes off).
chapter of the FIM for
troubleshooting.
May 10 Page 52
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 53
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 36-11-00-810-
FAULT CONDITION: The message BLEED 2 OFF comes into view
814A
on the EICAS.
36 BLEED 2 OFF No.
PROCEDURE: Make sure that the bleed 2 pushbutton is in the
Refer to the correspondent
AUTO position (pushed - light goes off).
chapter of the FIM for
troubleshooting.
May 10 Page 54
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 32-41-00-810-
FAULT CONDITION: After the aircraft power-up
BRK 860-A
32 CONTROL PROCEDURE:
No.
FAULT De-energize the aircraft (AMM TASK 24-42-02-860-802-A);
Refer to the correspondent
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
chapter of the FIM for
troubleshooting.
May 10 Page 55
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
CAS MSG If the message does not go out of view do the power-down/up
Compare the two CAS
procedure to reset the SPDAs. To do this, you must de-energize the
31 INDICATION aircraft (AMM TASK 24-42-02-860-802-A/200) and energize it again
message lists and do the
ON PFD related fault isolation task.
(AMM TASK 24-42-02-860-801-A/200).
May 10 Page 56
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH SPDA BLOCK 6.1 (MICRO/COMM PN 1705540D)]
FAULT CONDITION: Aircraft changes directly from Ground Service Mode to
any other operating mode such as:
Ground Service to Batteries
Ground Service to GPU
Ground Service to APU Gen
May 10 Page 57
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE:
On the CMC, use the sequence that follows to do the MRC 1 NIM
reset test (AMM TASK 45-45-00-970-805-A/200): Yes.
34 - NAVIGATION FIM TASK 23-51-00-810-
Chimes not 02 - MODULAR RADIO CABINET 1 - NIC 849-A
MRC1 NIM [NIC] MODULE RESET TEST
23 available - All No.
Positions Afterwards, on the CMC, use the sequence that follows to do the Refer to the correspondent
MRC 2 NIM reset test (AMM TASK 45-45-00-970-805-A/200): chapter of the FIM for
34 - NAVIGATION troubleshooting.
02 - MODULAR RADIO CABINET 2 - NIC
MRC2 NIM [NIC] MODULE RESET TEST
PROCEDURE:
Yes.
CAUTION: MAKE SURE THAT THE INTEGRATED
FIM TASK 23-24-00-810-
PITOT/STATIC/AOA SENSORS, TAT SENSORS, ICE
907-A
DETECTORS, AND STATIC PORT HAVE NO COVERS ON THEM
23 CMF 1 FAIL BEFORE YOU DO THE MAINTENANCE PROCEDURE. THESE
No.
COMPONENTS CAN BECOME HOT DURING THE
Refer to the correspondent
MAINTENANCE PROCEDURE. AS A RESULT, DAMAGE TO
chapter of the FIM for
THEM WILL OCCUR IF YOU DO NOT REMOVE THE COVERS.
troubleshooting.
Open this circuit breaker and, after approximately 5 seconds, close
it:
MAU 3 PWR 2-RHCBP (DC BUS 2)
May 10 Page 58
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 59
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
Copilot DAP FIM TASK 23-51-00-810-
Problems - PROCEDURE: 854-A
Open this circuit breaker and, after approximately 5 seconds, close
23 Display, it: No.
Volume and COMM AUDIO 2-RHCBP (DC ESS BUS 2) Refer to the correspondent
Controls chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 31-31-00-810-
On the MCDU, use the sequence in parentheses to open these 810-A
SSPCs. After approximately 10 seconds, close them:
31 CVR AFT FAIL FDR ACCEL-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) No.
DVDR 2-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 60
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 31-31-00-810-
On the MCDU, use the sequence in parentheses to open these 809-A
SSPCs. After approximately 10 seconds, close them:
31 CVR FWD FAIL FDR ACCEL-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) No.
DVDR 1-SPDA1 (CBMENU/CB BY SYS/FDR/CVR) Refer to the correspondent
chapter of the FIM for
troubleshooting.
PROCEDURE: Yes.
DATALINK 1) On the MCDU 1, push the CLR key as necessary until you clear FIM TASK 23-24-00-810-
TIMEOUT the scratchpad; 905-A
2) On the MCDU 1, push the MENU function key and then, the DLK
23 Shows on the function key; No.
MCDU 1 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
May 10 Page 61
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: Yes.
DATALINK 1) On the MCDU 2, push the CLR key as necessary until you clear FIM TASK 23-24-00-810-
TIMEOUT the scratchpad; 906-A
2) On the MCDU 2, push the MENU function key and then, the DLK
23 Shows on the function key; No.
MCDU 2 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
Yes.
FIM TASK 31-61-00-810-
88G-A
Open this circuit breaker and, after approximately 5 seconds, close
31 EICAS FAULT it: No.
EICAS-LHCBP (DC ESS BUS 1 DISPLAY/CONTROL)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 62
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 27-30-00-810-
801-A
Make sure that the hydraulic systems are on. On the FLIGHT
ELEVATOR
27 CONTROLS panel, push the ELEVATORS pushbutton. After 3
FAULT No.
seconds, push it again.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FAULT CONDITION: Hydraulic systems are OFF No maintenance action.
No.
PROCEDURE: Pressurize No. 1, No. 2, and No. 3 hydraulic Refer to the correspondent
systems (AMM TASK 29-10-00-863-802-A/200). chapter of the FIM for
ELEVATOR LH troubleshooting.
27
FAIL
FAULT CONDITION: Hydraulic systems are ON Yes.
FIM TASK 27-03-00-810-90Y-A
PROCEDURE: On the FLIGHT CONTROLS panel, push the No. Refer to the correspondent
ELEVATORS pushbutton. After 3 seconds, push it again. chapter of the FIM for
troubleshooting.
May 10 Page 63
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
No maintenance action.
FAULT CONDITION: Hydraulic systems are OFF
No.
PROCEDURE: Pressurize No. 1, No. 2, and No. 3 hydraulic Refer to the correspondent
systems (AMM TASK 29-10-00-863-802-A/200). chapter of the FIM for
troubleshooting.
ELEVATOR RH
27
FAIL Yes.
FAULT CONDITION: Hydraulic systems are ON FIM TASK 27-03-00-810-
92K-A
PROCEDURE: On the FLIGHT CONTROLS panel, push the
ELEVATORS pushbutton. After 3 seconds, push it again. No. Refer to the
correspondent chapter of
the FIM for
troubleshooting.
May 10 Page 64
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 73-21-00-810-
PROCEDURE: Open these circuit breakers and close them after 5 82C-A
ENG 1 FADEC seconds to confirm that the failure has occurred:
73
FAULT FADEC 1A-LHCBP (DC ESS BUS 1 ENGINE) No.
FADEC 1B-RHCBP (DC ESS BUS 2 ENGINE) Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 65
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
FAULT CONDITION: If there is a CMC message correlated to the
EICAS message.
PROCEDURE: Make sure that all fuel pumps are off and the
engines are not running. Do the steps that follow:
NOTE: Do not perform this procedure during the refueling
procedure.
On the FUEL panel, set the XFEED switch to the LOW1 position;
Open the access door of the refueling panel (616HB);
On the refueling panel, set the DEFUELING switch to the OPEN Yes.
position; FIM TASK 73-31-00-810-
Wait for 30 seconds; 805-A
ENG 1 FUEL On the refueling panel, set the DEFUELING switch to the
73
SW FAIL CLOSED position; No.
Close the access door of refueling panel (616HB); Refer to the correspondent
On the FUEL panel, set the XFEED switch to the OFF position; chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
May 10 Page 66
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 73-21-00-810-
PROCEDURE: Open these circuit breakers and close them after 5 82C-A
ENG 2 FADEC seconds to confirm that the failure has occurred:
73
FAULT FADEC 2A-LHCBP (DC ESS BUS 1 ENGINE) No.
FADEC 2B-RHCBP (DC ESS BUS 2 ENGINE) Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 67
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
FAULT CONDITION: If there is a CMC message correlated to the
EICAS message.
PROCEDURE: Make sure that all fuel pumps are off and the
engines are not running. Do the steps that follow:
NOTE: Do not perform this procedure during the refueling
procedure.
On the FUEL panel, set the XFEED switch to the LOW1 position;
Open the access door of the refueling panel (616HB) ;
On the refueling panel, set the DEFUELING switch to the OPEN Yes.
position; FIM TASK 73-31-00-810-
Wait for 30 seconds; 805-A
ENG 2 FUEL On the refueling panel, set the DEFUELING switch to the
73
SW FAIL CLOSED position; No.
Close the access door of refueling panel (616HB); Refer to the correspondent
On the FUEL panel, set the XFEED switch to the OFF position; chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
May 10 Page 68
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
FAULT CONDITION: The following maintenance messages are active on the CMC:
22310005TA1 - ENGINE DATA [TRSA1] FAULT
22310005TA2 - ENGINE DATA [TRSA2] FAULT
22310023TA1 - FADEC1/FADEC2 [ATA1] WRG FAULT
22310023TA2 - FADEC1/FADEC2 [ATA2] WRG FAULT
22310079TA1 - LEFT FADEC [ATA1] FAULT
22310079TA2 - LEFT FADEC [ATA2] FAULT
22310080TA1 - RIGHT FADEC [ATA1] FAULT
22310080TA2 - RIGHT FADEC [ATA2] FAULT
NOTE: The recording of "RIGHT FADEC [ATxx] FAULT" or "LEFT FADEC [ATxx]
FAULT" maintenance message on the CMC depends on the faulty FADEC. The left
FADEC refers to engine 1 and the right FADEC refers to engine 2. Yes.
FIM TASK 22-31-00-810-821-A
EFF: [ALL]
ENG TLA TRIM PROCEDURE:
22 No.
FAIL On the CMC, use the sequence that follows to get access to the ENGINE 1 GENERAL
Refer to the correspondent
STATUS PAGE:
73 - ENGINE FUEL AND CONTROL
chapter of the FIM for
21 - ENGINE FADEC 1A troubleshooting.
ENGINE 1 GENERAL STATUS PAGE
If the CHANNEL IN CONTROL status is the same for both channels, go to the FIM
TASK 22-31-00-810-821-A.
On the CMC, use the sequence that follows to get access to the ENGINE 2 GENERAL
STATUS PAGE:
73 - ENGINE FUEL AND CONTROL
21 - ENGINE FADEC 2A
ENGINE 2 GENERAL STATUS PAGE
If the CHANNEL IN CONTROL status is the same for both channels, go to the FIM
TASK 22-31-00-810-821-A.
May 10 Page 69
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 31-31-00-810-
On the MCDU, use the sequence in parentheses to open these 808-A
SSPCs and, after approximately 10 seconds, close them:
31 FDR AFT FAIL FDR ACCEL-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) No.
DVDR 2-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 31-31-00-810-
On the MCDU, use the sequence in parentheses to open these 807-A
SSPCs and, after approximately 10 seconds, close them:
31 FDR FWD FAIL FDR ACCEL-SPDA2 (CBMENU/CB BY SYS/FDR/CVR) No.
DVDR 1-SPDA1 (CBMENU/CB BY SYS/FDR/CVR) Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 70
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 71
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 72
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Do the flight control electrical P-BIT (Power-up Built-in Test). To do this
test, you must de-energize the aircraft (AMM TASK 24-42-02-860-802-
A/200) and energize it again (AMM TASK 24-42-02-860-801-A/200).
NOTE: The flight control electrical built-in test is complete three minutes
after the AC power is connected to the aircraft. If you set the hydraulic
pump to ON before that, the flight control electrical built-in test is
canceled.
You must not move the flight control commands. If you move the
flight control commands with the hydraulic pressure off, a CAS message
will show.
Pressurize No. 1, No. 2 and No. 3 hydraulic systems (AMM TASK 29-10- Yes.
00-863-802-A/200) to do the flight control hydraulic P-BIT (Power-up FIM TASK 27-00-00-810-
Built-in Test). 801-A
FLT CTRL BIT NOTE: You must not move the flight control commands until the flight
27
EXPIRED control actuators engages in the daily switch configuration. No.
Make sure that the rudder surface is not fully deflected to the Refer to the correspondent
LEFT position (due to wind action, for instance). chapter of the FIM for
If the fault is not removed, do the flight control electrical P-BIT (Power-up troubleshooting.
Built-in Test) again. To do this test, you must de-energize the aircraft
(AMM TASK 24-42-02-860-802-A/200) and energize it again (AMM
TASK 24-42-02-860-801-A/200).
NOTE: The flight control electrical built-in test is complete three minutes
after the AC power is connected to the aircraft. If you set the hydraulic
pump to ON before that, the flight control electrical built-in test is
canceled.
You must not move the flight control commands. If you move the
flight control commands with the hydraulic pressure off, a CAS message
will show.
May 10 Page 73
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Make sure that the hydraulic systems are on. On the FLIGHT Yes.
CONTROLS panel, push the ELEVATORS, RUDDER and FIM TASK 27-03-00-810-
SPOILERS pushbuttons. After 3 seconds, push them again. Do the 91A-A
FLT CTRL P-BIT (Power-up Built-in Test). To do this test, you must de-
27
FAULT energize the aircraft (AMM TASK 24-42-02-860-802-A/200) and No.
energize it again (AMM TASK 24-42-02-860-801-A/200). Do the Refer to the correspondent
return-to-service test of the flight control system (AMM TASK 27-00- chapter of the FIM for
00-070-801-A/200). troubleshooting.
May 10 Page 74
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 75
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: On the maintenance panel, make sure the FCS MAINT switch is in the
OFF position.
Pressurize the No. 1, No. 2, and No. 3 hydraulic systems (AMM TASK 29-10-00-863-
802-A/200).
NOTE: Wait 1 minute until the FCS PCUs engage in the daily switch configuration.
You must not move the flight control commands until the flight control PCUs engage
in the daily switch configuration.
FLT CTRL NO Make sure that the rudder surface is not fully deflected to the LEFT position (due to
DISPATCH/FLT wind action, for instance).
On the FLIGHT CONTROLS panel, push the ELEVATORS, RUDDER, and
CTRL SPOILERS pushbuttons. After 3 seconds, push them again. Yes..
FAULT/FLT Do the return-to-service test of the flight control system until you push the CLEAR FIM TASK 27-00-00-810-801-A
CTRL BIT RAM button (CMC Page 2) (AMM TASK 27-00-00-070-801-A/200).
27 Set the FCS MAINT switch to the OFF position. No.
EXPIRED, Examine the message window on the EICAS display and make sure that there are no Refer to the correspondent
AUTO CONFIG FLT CTRL NO DISPATCH/FLT CTRL FAULT/FLT CTRL BIT EXPIRED messages: chapter of the FIM for
1) If there are none of these error messages, continue the return-to-service test of the troubleshooting.
TRIM FAIL flight control system (AMM TASK 27-00-00-070-801-A/200);
(Alternate 2) If there are any of these error messages, on the HYDRAULIC control panel, set the
SYS 1, SYS 2 and SYS 3 - ELEC PUMP switches to OFF and do the P-BIT
procedure) (Power-up Built-in Test). To do this test, you must de-energize the aircraft
(AMM TASK 24-42-02-860-802-A/200) and energize it again (AMM TASK 24-42-02-
860-801-A/200).
NOTE: The flight control electrical built-in test is completed three minutes after the
AC power is connected to the aircraft. If you set
the hydraulic pump to ON before that, the flight control electrical built-in test is
cancelled.
You must not move the flight control commands. If you move the flight control
commands with the hydraulic pressure off, a CAS message will show.
May 10 Page 76
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH FMS2 AND MAU2 PWR2 PRI CIRCUIT
BREAKER ON DC BUS 2]
EFF: ALL
May 10 Page 77
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
May 10 Page 78
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: Yes.
FMS1 1) On MCDU 1, push the CLR key as necessary until you clear the FIM TASK 34-61-00-810-
TIMEOUT scratchpad; 890-A
2) On MCDU 1, push the MENU function key and then the
34 Shows on the applicable FMS function key; No.
MCDU 1 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
May 10 Page 79
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: Yes.
FMS1-2 1) On MCDU 1, push the CLR key as necessary until you clear the FIM TASK 34-61-00-810-
TIMEOUT scratchpad; 898-A
2) On MCDU 1, push the MENU function key and then the
34 Shows on the applicable FMS function key; No.
MCDU 1 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
May 10 Page 80
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: Yes.
FMS1-2 1) On MCDU 2, push the CLR key as necessary until you clear the FIM TASK 34-61-00-810-
TIMEOUT scratchpad; 899-A
2) On MCDU 2, push the MENU function key and then the
34 Shows on the applicable FMS function key; No.
MCDU 2 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
May 10 Page 81
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE: Yes.
FMS2 1) On MCDU 2, push the CLR key as necessary until you clear the FIM TASK 34-61-00-810-
TIMEOUT scratchpad; 891-A
2) On MCDU 2, push the MENU function key and then the
34 Shows on the applicable FMS function key; No.
MCDU 2 3) If the message persists, do the steps that follows: Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A). troubleshooting.
May 10 Page 82
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 28-22-00-810-
808-A
FUEL DC
28 On the FUEL overhead panel, set DC PUMP to ON. Wait 10
PUMP FAIL No.
seconds and set it back to AUTO.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 28-21-00-810-
820-A
FUEL EQUAL-
28 Make sure that the XFEED switch is in the OFF position.
XFEED OPEN No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 83
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH SPDA BLOCK 6.1 (MICRO/COMM PN 1705540D)]
May 10 Page 84
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: [ON ACFT WITH MAU2 PWR2 PRI CIRCUIT BREAKER ON
DC BUS 2]
EFF: ALL
May 10 Page 85
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 27-03-00-810-
GROUND 83B-A
Do the return-to-service test of the flight control system (AMM TASK
27 SPOILERS 27-00-00-070-801-A/200). No.
FAIL Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-25-00-810-
EFF: [ON ACFT WITH DUAL HEAD-UP GUIDANCE SYSTEM]
805-A
Open these circuit breakers and, after a minimum of 60 seconds,
34 HUD 1 FAIL close them:
No.
COMPUTER - RHCBP - DC BUS 2/HUD 1
Refer to the correspondent
OVHD UNIT - RHCBP - DC BUS 2/HUD 1
chapter of the FIM for
troubleshooting.
May 10 Page 86
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 34-25-00-810-
EFF: [ON ACFT WITH DUAL HEAD-UP GUIDANCE SYSTEM]
806-A
Open these circuit breakers and, after a minimum of 60 seconds,
34 HUD 2 FAIL close them:
No.
COMPUTER - LHCBP - DC BUS 1/HUD 2
Refer to the correspondent
OVHD UNIT - LHCBP - DC BUS 1/HUD 2
chapter of the FIM for
troubleshooting.
May 10 Page 87
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 34-25-00-810-
EFF: [ON ACFT WITH SINGLE HEAD-UP GUIDANCE SYSTEM]
805-A
Open these circuit breakers and, after a minimum of 60 seconds,
34 HUD FAIL close them:
No.
COMPUTER - RHCBP - DC BUS 2/HUD
Refer to the correspondent
OVHD UNIT - RHCBP - DC BUS 2/HUD
chapter of the FIM for
troubleshooting.
May 10 Page 88
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: 170 - [ON EMBRAER 170 ACFT WITH PRIMUS EPIC LOAD
17.1 AND ON] OR [POST-MOD 170-31-0010/01]
190 - [ON EMBRAER 190 ACFT WITH PRIMUS EPIC LOAD 4.2
AND ON]
PROCEDURE:
WARNING: DO NOT OPERATE THE ENGINE OR
PRESSURIZE THE BLEED AIR SYSTEM. THE BLEED AIR WILL
Yes.
FLOW OUT OF THE BLEED AIR LINE AND CAUSE INJURIES TO
FIM TASK 30-81-00-810-
PERSONS.
ICE 801-A
30 DETECTOR 1 WARNING: DO NOT TOUCH THE INTEGRATED
No.
FAIL PITOT/STATIC AOA SENSOR, TAT SEN-SOR, STATIC PORT
Refer to the correspondent
AND ICE DETECTORS IMMEDIATELY AFTER THE HEATER
chapter of the FIM for
WAS SET TO OFF TO PREVENT INJURY
troubleshooting.
TO PERSONS.
May 10 Page 89
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
EFF: 170 - [ON EMBRAER 170 ACFT WITH PRIMUS EPIC LOAD
17.1 AND ON] OR [POST-MOD 170-31-0010/01]
190 - [ON EMBRAER 190 ACFT WITH PRIMUS EPIC LOAD 4.2
AND ON]
PROCEDURE:
WARNING: DO NOT OPERATE THE ENGINE OR
PRESSURIZE THE BLEED AIR SYSTEM. THE BLEED AIR WILL
Yes.
FLOW OUT OF THE BLEED AIR LINE AND CAUSE INJURIES TO
FIM TASK 30-81-00-810-
PERSONS.
ICE 802-A
30 DETECTOR 2 WARNING: DO NOT TOUCH THE INTEGRATED
No.
FAIL PITOT/STATIC AOA SENSOR, TAT SEN-SOR, STATIC PORT
Refer to the correspondent
AND ICE DETECTORS IMMEDIATELY AFTER THE HEATER
chapter of the FIM for
WAS SET TO OFF TO PREVENT INJURY
troubleshooting.
TO PERSONS.
May 10 Page 90
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
PROCEDURE:
On the CMC, use the sequence that follows to do the MRC 1 NIM
reset test (AMM TASK 45-45-00-970-805-A/200): Yes.
INPH audio 34 - NAVIGATION FIM TASK 23-51-00-810-
(Between 02 - MODULAR RADIO CABINET 1 - NIC 831-A
MRC1 NIM [NIC] MODULE RESET TEST
23 DAPs) - Noisy No.
or not Afterwards, on the CMC, use the sequence that follows to do the Refer to the correspondent
Available MRC 2 NIM reset test (AMM TASK 45-45-00-970-805-A/200): chapter of the FIM for
34 - NAVIGATION troubleshooting.
02 - MODULAR RADIO CABINET 2 - NIC
MRC2 NIM [NIC] MODULE RESET TEST
May 10 Page 91
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 34-26-00-810-
Open these circuit breakers and, after approximately 5 seconds, 801-A
close them:
34 IRS 1 FAIL IRS 1 PWR 1-LHCBP (DC ESS BUS 1 NAV) No.
IRS 1 PWR 2-RHCBP (DC ESS BUS 2 NAV) Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-26-00-810-
Open these circuit breakers and, after approximately 5 seconds, 808-A
close them:
34 IRS 2 FAIL IRS 2 PWR 1-RHCBP (DC BUS 2 NAV) No.
IRS 2 PWR 2-LHCBP (DC BUS 1 NAV) Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 92
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
On the MCDU, do the steps that follow to get access to the POS
SENSORS page:
Push the NAV function key to show the NAV INDEX page 1/2. Yes.
Push the LSK (NAV IDENT) to show the NAV IDENT page. FIM TASK 34-26-00-810-
Push the LSK (POS INIT) to show the POSITION INIT page. 805-A
IRS PRES POS Push the LSK (POS SENSORS) to show the POS SENSORS
34
INVALID page. No.
If the GPS 1/2 is not available on the POS SENSORS page of the Refer to the correspondent
MCDU, put the aircraft out of the hangar or in a place where the chapter of the FIM for
GPS signal is available. troubleshooting.
Note: "IRS PRES POS INVALID" CAS message comes into view if
the GPS signal is not available.
May 10 Page 93
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FAULT CONDITION: CMC indicates a failure in the forward FIM TASK 26-14-00-02-
lavatory smoke detector during the test 810-801-A
May 10 Page 94
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FAULT CONDITION: CMC indicates a failure in the forward FIM TASK 26-14-00-02-
lavatory smoke detector 810-801-A
May 10 Page 95
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 32-00-00-810-
FAULT CONDITION: During power-up
801-A
LG NO
32 PROCEDURE: Reset MAU 1 PWR 1-LHCBP (DC ESS BUS 1).
DISPATCH No.
If it does not clear the message, reset MAU 3 PWR 1.
Refer to the correspondent
If it does not clear the message, reset the aircraft power.
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 32-00-00-810-
FAULT CONDITION: During power-up
801-A
LG NOSE
32 PROCEDURE: Reset MAU 1 PWR 1-LHCBP (DC ESS BUS 1).
DOOR OPEN If it does not clear the message, reset MAU 3 PWR 1.
No.
Refer to the correspondent
If it does not clear the message, reset the aircraft power.
chapter of the FIM for
troubleshooting.
May 10 Page 96
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 32-00-00-810-
FAULT CONDITION: During power-up
801-A
LG WOW SYS
32 PROCEDURE: Reset MAU 1 PWR 1-LHCBP (DC ESS BUS 1).
FAIL No.
If it does not clear the message, reset MAU 3 PWR 1.
Refer to the correspondent
If it does not clear the message, reset the aircraft power.
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 31-61-00-810-
88E-A
Open this circuit breaker and, after approximately 5 seconds, close
31 MFD 1 FAULT it: No.
MFD 1-RHCBP (DC ESS BUS 2 DISPLAY/CONTROL)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 97
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 31-61-00-810-
88F-A
Open this circuit breaker and, after approximately 5 seconds, close
31 MFD 2 FAULT it: No.
MFD 2-LHCBP (DC BUS 1 DISPLAY/CONTROL)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-02-00-810-
804-A
Open this circuit breaker and, after approximately 5 seconds, close
NAVCOM 1
34 it:
FAIL MRC 1-LHCBP (DC ESS BUS 1 COMM)
No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 98
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 34-02-00-810-
818-A
On the MCDU, use the sequence in parentheses to open the SSPC
NAVCOM 2
34 below. After a minimum of 10 seconds, close it:
FAIL No.
MRC 2-SPDA2 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 28-41-00-810-
NO LEFT FUEL 820-A
Open this circuit breaker and, after approximately 5 seconds, close
QTY
28 it:
INDICATION FUEL QTY 1 - LHCBP - DC ESS BUS 1 . No.
ON EICAS Refer to the correspondent
chapter of the FIM for
troubleshooting.
May 10 Page 99
MESSAGE / IS THE FAULT
ATA MAINTENANCE ACTION REMOVED?
FAULT
Yes.
FIM TASK 28-41-00-810-
NO RIGHT 821-A
Open this circuit breaker and, after approximately 5 seconds, close
FUEL QTY
28 it:
INDICATION FUEL QTY 2 - RHCBP - DC ESS BUS 2
No.
ON EICAS Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 28-41-00-810-
NO TOTAL Open these circuit breakers and, after approximately 5 seconds, 822-A
FUEL QTY close them:
28
INDICATION FUEL QTY 1 - LHCBP - DC ESS BUS 1 No.
ON EICAS FUEL QTY 2 - RHCBP - DC ESS BUS 2 Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
Observer DAP FIM TASK 23-51-00-810-
Problems - PROCEDURE: 855-A
Open this circuit breaker and, after approximately 5 seconds, close
23 Display, it: No.
Volume and COMM AUDIO 3-LHCBP (DC BUS 1) Refer to the correspondent
Controls chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 31-61-00-810-
88C-A
Open this circuit breaker and, after approximately 5 seconds, close
31 PFD 1 FAULT it:
No.
PFD 1-LHCBP (DC BUS 1 DISPLAY/CONTROL)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 31-61-00-810-
88D-A
Open this circuit breaker and, after approximately 5 seconds, close
31 PFD 2 FAULT it:
No.
DISPLAY PFD 2-RHCBP (DC BUS 2)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
Pilot DAP FIM TASK 23-51-00-810-
Problems - PROCEDURE: 853-A
Open this circuit breaker and, after approximately 5 seconds, close
23 Display, it: No.
Volume and AUDIO 1-LHCBP (DC ESS BUS 1 COMM) Refer to the correspondent
Controls chapter of the FIM for
troubleshooting.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the OFF position at the same time.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the ON position at the same time. Yes.
Do the return-to-service test of the flight control system (AMM FIM TASK 27-43-00-810-
TASK 27-00-00-070-801-A/200). 809-A
PITCH TRIM Push and hold the BACKUP PITCH TRIM switch to the nose-up
27
BKUP FL position for 3 to 5 seconds. Make sure that the leading edge of the No.
horizontal stabilizer moves down a short distance and then stops, Refer to the correspondent
and that the PITCH trim indication on the EICAS moves up. chapter of the FIM for
Push and hold the BACKUP PITCH TRIM switch to the nose-down troubleshooting.
position for 3 to 5 seconds. Make sure that the leading edge of the
horizontal stabilizer moves up a short distance and then stops, and
that the PITCH trim indication on the EICAS moves down.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the OFF position at the same time.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the ON position at the same time. Yes.
If the fault is not removed, do the return-to-service test of the flight FIM TASK 27-41-00-810-
control system (AMM TASK 27-00-00-070-801-A/200). 809-A
PITCH TRIM Push and hold the BACKUP PITCH TRIM switch to the nose-up
27
FAIL position for 3 to 5 seconds. Make sure that the leading edge of the No.
horizontal stabilizer moves down a short distance and then stops, Refer to the correspondent
and that the PITCH trim indication on the EICAS moves up. chapter of the FIM for
Push and hold the BACKUP PITCH TRIM switch to the nose-down troubleshooting.
position for 3 to 5 seconds. Make sure that the leading edge of the
horizontal stabilizer moves up a short distance and then stops, and
that the PITCH trim indication on the EICAS moves down.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the OFF position at the same time.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the ON position at the same time.
Yes.
Do the return-to-service test of the flight control system (AMM
FIM TASK 27-43-00-810-
TASK 27-00-00-070-801-A/200).
801-A
Push and hold the pilot control-yoke pitch-trim switch to the nose-
PITCH TRIM
27 up position for 3 to 5 seconds. Make sure that the leading edge of
SW 1 FAIL No.
the horizontal stabilizer moves down a short distance and then
Refer to the correspondent
stops, and that the PITCH trim indication on the EICAS moves up.
chapter of the FIM for
Push and hold the pilot control-yoke pitch-trim switch to the nose-
troubleshooting.
down position for 3 to 5 seconds. Make sure that the leading edge
of the horizontal stabilizer moves up a short distance and then
stops, and that the PITCH trim indication on the EICAS moves
down.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the OFF position at the same time.
On the TRIM control panel, push the SYS 1 CUTOUT and SYS 2
CUTOUT pushbuttons to the ON position at the same time.
Yes.
Do the return-to-service test of the flight control system (AMM
TASK 27-00-00-070-801-A/200).
FIM TASK 27-43-00-810-
Push and hold the copilot control-yoke pitch-trim switch to the
802-A
PITCH TRIM nose-up position for 3 to 5 seconds. Make sure that the leading
27
SW 2 FAIL edge of the horizontal stabilizer moves down a short distance and
No.
then stops, and that the PITCH trim indication on the EICAS moves
Refer to the correspondent
up.
chapter of the FIM for
Push and hold the copilot control-yoke pitch-trim switch to the
troubleshooting.
nose-down position for 3 to 5 seconds. Make sure that the leading
edge of the horizontal stabilizer moves up a short distance and then
stops, and that the PITCH trim indication on the EICAS moves
down.
During servicing, draining or when the passenger use the lavatory Yes.
POTABLE or the flight attendant use the galleys. FIM TASK 38-00-00-810-
WATER OR PROCEDURE: 801A.
Reset the WWSC. Open these circuit breakers and, after
38 WASTE approximately 5 seconds, close them: No. Refer to the
SYSTEM WATER WASTE CTRL1 - LICC - DC GND SVC BUS correspondent chapter of
INOPERATIVE. WATER WASTE CTRL2 - LICC - DC BUS 1 the FIM for
WATERWASTE CTRL3 - AICC - HOT BATT BUS 3 troubleshooting.
Yes.
PROCEDURE:
RADIOS FIM TASK 23-12-00-810-
1) On MCDU 1, push the CLR key until you clear the scratchpad;
TIMEOUT 863-A
2) On MCDU 1, push the MENU function key and then, the RADIO
23 Shows on the function key;
No.
MCDU 1 3) If the message persists, do the steps that follows:
Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A);
chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
troubleshooting.
Yes.
PROCEDURE:
RADIOS FIM TASK 23-12-00-810-
1) On MCDU 2, push the CLR key until you clear the scratchpad;
TIMEOUT 864-A
2) On MCDU 2, push the MENU function key and then, the RADIO
23 Shows on the function key;
No.
MCDU 2 3) If the message persists, do the steps that follows:
Refer to the correspondent
Scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A);
chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
troubleshooting.
Yes.
FIM TASK 34-31-00-810-
801-A
On the MCDU, use the sequence in parentheses to open this
34 RALT 1 FAIL SSPC. After approximately 10 seconds, close it:
No.
RALT 1-SPDA2 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-31-00-810-
802-A
On the MCDU, use the sequence in parentheses to open this
34 RALT 2 FAIL SSPC. After approximately 10 seconds, close it:
No.
RALT 2-SPDA1 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
EFF: [ON ACFT WITH SPDA BLOCK 9 AND AMS BLACK LABEL Yes.
UP TO 4.0] FIM TASK 21-25-00-810-
804.
RAM AIR FAULT CONDITION: Aircraft changes directly from Ground Service
21
FAULT Mode to any other operating mode such as: No.
Ground Service to Batteries Refer to the correspondent
Ground Service to GPU chapter of the FIM for
Ground Service to APU Gen troubleshooting.
PROCEDURE:
1) On MCDU 1, push the CLR key as necessary until you clear the Yes.
REFUEL PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 1, push the MENU function key; 892-A
3) On MCDU 1, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 1 4) On MCDU 1, push the LSK adjacent to REFUEL; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
PROCEDURE:
1) On MCDU 2, push the CLR key as necessary until you clear the Yes.
REFUEL PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 2, push the MENU function key; 893-A
3) On MCDU 2, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 2 4) On MCDU 2, push the LSK adjacent to REFUEL; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
EFF: [ACFT WITH SPDA S/W BLOCK 11.1 AND ON, AND WITH
CMC LDI V08 AND ON]
PROCEDURE: If the message is related to a system that was
intentionally deactivated, do the thermal CB/SSPC status
acknowledgement to clear the message on the MCDU (AMM TASK
24-60-00-910-801-A/200).
Yes.
No maintenance action.
FAULT CONDITION: Hydraulic systems OFF
27 RUDDER FAIL PROCEDURE: Pressurize No. 1, No. 2 and No. 3 hydraulic No.
Refer to the correspondent
systems (AMM TASK 29-10-00-863-802-A/200).
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 27-20-00-810-
801-A
Make sure that the hydraulic systems are on. On the FLIGHT
RUDDER
27 CONTROLS panel, push the RUDDER pushbutton. After 3
FAULT seconds, push it again.
No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
PROCEDURE:
1) On MCDU 1, push the CLR key as necessary until you clear the Yes.
SETUP PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 1, push the MENU function key; 894-A
3) On MCDU 1, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 1 4) On MCDU 1, push the LSK adjacent to SETUP; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
PROCEDURE:
1) On MCDU 2, push the CLR key as necessary until you clear the Yes.
SETUP PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 2, push the MENU function key; 895-A
3) On MCDU 2, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 2 4) On MCDU 2, push the LSK adjacent to SETUP; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
FAULT CONDITION: The SPDA FAIL CAS message was displayed Yes.
during flight and the CMC maintenance message is related to the FIM TASK 24-61-00-810-
SPDA MICRO/COMMS module(s) (Fault Codes: 24610004SP2, 810-A
24610016SP2, 24610004SP1 and/or 24610017SP1)
24 SPDA FAIL
PROCEDURE: Do the power-down/up procedure to reset the No.
SPDAs. To do this, you must de-energize the aircraft (AMM TASK Refer to the correspondent
24-42-02-860-802-A/200) and energize it again (AMM TASK 24-42- chapter of the FIM for
02-860-801-A/200). troubleshooting.
Yes.
FIM TASK 32-53-00-810-
806-A
PROCEDURE: Open this circuit breaker and, after 5 seconds, close
32 STEER FAIL it:
No.
MAU 2 PWR 1-RHCBP (DC BUS 2)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-15-00-810-
808-A
Open this circuit breaker and, after approximately 5 seconds, close
34 TAT 2 FAIL it:
No.
ADS 2 PROBE 4A-RHCBP (DC BUS 2 NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-43-00-810-
801-A
On the MCDU, use the sequence in parentheses to open this SSPC
34 TCAS FAIL and, after a minimum of 10 seconds, close it:
No.
TCAS-SPDA1 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
EFF: ALL
EFF: ALL
PROCEDURE:
1) On MCDU 1, push the CLR key as necessary until you clear the Yes.
TEST PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 1, push the MENU function key; 896-A
3) On MCDU 1, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 1 4) On MCDU 1, push the LSK adjacent to TEST; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
PROCEDURE:
1) On MCDU 2, push the CLR key as necessary until you clear the Yes.
TEST PG scratchpad; FIM TASK 34-61-00-810-
TIMEOUT 2) On MCDU 2, push the MENU function key; 897-A
3) On MCDU 2, push the LSK adjacent to MISC to get access to the
34 Shows on the MISC MENU page; No.
MCDU 2 4) On MCDU 2, push the LSK adjacent to TEST; Refer to the correspondent
Scratchpad 5) If the message persists, do the steps that follows: chapter of the FIM for
De-energize the aircraft (AMM TASK 24-42-02-860-802-A); troubleshooting.
Energize the aircraft (AMM TASK 24-42-02-860-801-A).
PROCEDURE: Yes.
THRUST MGT 1) On MCDU 1, push the CLR key as necessary until you clear the FIM TASK 76-12-00-810-
TIMEOUT scratchpad; 802-A
2) On MCDU 1, push the MENU function key and then, the TRS
76 shows on the function key; No.
MCDU 1 3) If the message persists, do the steps that follows: Refer to the correspondent
scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A) troubleshooting.
PROCEDURE: Yes.
THRUST MGT 1) On MCDU 2, push the CLR key as necessary until you clear the FIM TASK 76-12-00-810-
TIMEOUT scratchpad; 803-A
2) On MCDU 2, push the MENU function key and then, the TRS
76 shows on the function key; No.
MCDU 2 3) If the message persists, do the steps that follows: Refer to the correspondent
scratchpad De-energize the aircraft (AMM TASK 24-42-02-860-802-A); chapter of the FIM for
Energize the aircraft (AMM TASK 24-42-02-860-801-A) troubleshooting.
Yes.
FIM TASK 24-31-00-810-
803-A
Cycle the TRU1 toggle switch from AUTO to OFF. Then, return it to
24 TRU 1 FAIL AUTO again. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 24-31-00-810-
804-A
Cycle the TRU2 toggle switch from AUTO to OFF. Then, return it to
24 TRU 2 FAIL AUTO again. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 24-31-00-810-
815-A
Cycle the TRU ESS toggle switch from AUTO to OFF. Then, return
24 TRU ESS FAIL it to AUTO again. No.
Refer to the correspondent
chapter of the FIM for
troubleshooting.
PROCEDURE:
On the CMC, use the sequence that follows to do the MRC 1 NIM
reset test (AMM TASK 45-45-00-970-805-A/200): Yes.
34 - NAVIGATION FIM TASK 23-51-00-810-
Uncommanded 02 - MODULAR RADIO CABINET 1 - NIC 845-A
chime MRC1 NIM [NIC] MODULE RESET TEST
23
generation - No.
All Positions Afterwards, on the CMC, use the sequence that follows to do the Refer to the correspondent
MRC 2 NIM reset test (AMM TASK 45-45-00-970-805-A/200): chapter of the FIM for
34 - NAVIGATION troubleshooting.
02 - MODULAR RADIO CABINET 2 - NIC
MRC2 NIM [NIC] MODULE RESET TEST
Yes.
PROCEDURE: FIM TASK 23-12-00-810-
Uncommanded On the CMC, use the sequence that follows to do the MRC 1 NIM 854-A
VHF COMM 1 reset test (AMM TASK 45-45-00-970-805-A/200):
23
Transmission - 34 - NAVIGATION No.
All Positions 02 - MODULAR RADIO CABINET 1 - NIC Refer to the correspondent
MRC1 NIM [NIC] MODULE RESET TEST chapter of the FIM for
troubleshooting.
Yes.
PROCEDURE: FIM TASK 23-12-00-810-
Uncommanded On the CMC, use the sequence that follows to do the MRC 2 NIM 858-A
VHF COMM 2 reset test (AMM TASK 45-45-00-970-805-A/200):
23
Transmission - 34 - NAVIGATION No.
All Positions 02 - MODULAR RADIO CABINET 2 - NIC Refer to the correspondent
MRC2 NIM [NIC] MODULE RESET TEST chapter of the FIM for
troubleshooting.
EFF: ALL
Yes.
FIM TASK 34-42-00-810-
WX FAIL On the MCDU (AMM SDS 34-61-00/1), use the sequence in 816-A
parentheses to open this SSPC and, after a minimum of 10
34 MESSAGE ON seconds, close it: No.
THE MFD WX RADAR-SPDA1 (CBMENU/CB BY SYS/NAV) Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-52-00-810-
801-A
On the MCDU, use the sequence in parentheses to open this
34 XPDR 1 FAIL SSPC. After a minimum of 10 seconds, close it:
No.
TRANSPONDER 1-SPDA1 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.
Yes.
FIM TASK 34-52-00-810-
802-A
On the MCDU, use the sequence in parentheses to open this
34 XPDR 2 FAIL SSPC. After a minimum of 10 seconds, close it:
No.
TRANSPONDER 2-SPDA2 (CBMENU/CB BY SYS/NAV)
Refer to the correspondent
chapter of the FIM for
troubleshooting.