Professional Documents
Culture Documents
99717
99717
99717 - PARTS DESCRIPTION & PRICE LIST BY FUNCTION - Effective February 2002
Notes: 1. All Fuel Manager Diesel Fuel Filter/Water Separator Systems remove both particulates AND water. It is very important to DRAIN
WATER REGULARLY. Even if a see-through water collection/storage bowl is not present, the filter/separator is removing water, and
must be drained.
2. All Fuel Manager Diesel Fuel Filter/Water Separator units can be installed on the suction side OR the low pressure side of the fuel
transfer pump.
3. All Fuel Manager FM 100 Series Diesel Fuel Filter/Water Separator Systems are suitable for any diesel engine or equipment with
fuel flows of up to 80 US galls/hr. (300 liters/hr) with 3/8" ports. This is equivalent to approximately 350 HP.
4. All Fuel Manager FM 1000 Series Diesel Fuel Filter/Water Separator Systems are suitable for any diesel engine or equipment with
fuel flows of up to 180 US galls/hr. (680 liters/hr). This is equivalent to approximately 600 HP.
Stanadyne Corporation
92 Deerfield Road, Windsor, CT 06095, U.S.A. Tel: (860) 525-0821; Fax: (860) 683-4587; www.stanadyne.com
Page 1 of 6
Suggested
Part No. Description Pkg. Qty.
List Price
CONVENTIONAL FM 100 SERIES FUEL FILTER/WATER SEPARATORS
Suitable for diesel engines with up to 80 US gallons/hr (300 liters/hr) total fuel flow (including return flow), or about 350 HP
FM 100 Series Complete "Starter" Kit containing a selection of components to custom build filter units
32902 Starter Kit - components to build FM assemblies. See PB2017 for contents 1 $956.02
FM 100 Series Header Assemblies (Mounting Headers with cap, volume plug, seals etc. No filter element.)
30837 Header Ass'y - Conventional - 1/2" - 20 straight thread (SAE) ports 1 $46.21
33260 Header Ass'y - Conventional - 1/4" - 18 NPTF ports (replaces 29888) 1 $46.21
33648 Header Ass'y - Conventional - 3/8" - 18 NPTF ports 1 $46.21
34504 Header Ass'y - Conventional - M12 x 1.5 'O' ring ports 1 $46.21
34306 Header Ass'y - Conventional - M14 x 1.5 'O' ring ports 1 $46.21
FM 100 Series Replacement Elements for conventional normal flow assemblies (Branded FUEL MANAGER in red )
150 micron Pre-Filter/Water Separator Replacement Elements
33169 150 micron Pre-filter Water Separator Element - 3.6" nominal length 12 $216.96
31649 150 micron Pre-filter Water Separator Element - 4.3" nominal length 12 $236.16
31648 150 micron Pre-filter Water Separator Element - 6.0" nominal length 12 $274.56
Page 2 of 6
Suggested
Part No. Description Pkg. Qty.
List Price
FM 100 Series Optional Module Kits (containing all parts and instructions)
31341 Heater Kit - 100 Watt - Top Load 12 volt 1 $64.46
32364 Heater Kit - 150 Watt - Top Load 12 volt (replaces 29255) 1 $72.77
33649 Heater Kit - 150 Watt - Top Load 24 volt 1 $73.90
32283 Heater Kit - 100 Watt - Side Load 1/4" - 18 NPT - 12 volt 1 $61.98
35160 Heater Kit - 100 Watt - Side Load 3/8" - 18 NPT - 12 volt 1 $61.98
30939 Heater Kit - 100 Watt - Side Load 1/2" - 20 straight thread - 12 volt 1 $61.98
34743 Heater Kit - 100 Watt - Side Load - M12 x 1.5 - 12 volt 1 $61.98
34144 Heater Kit - 100 Watt - Side Load 1/4" - 18 NPT - 24 volt 1 $64.48
34145 Heater Kit - 100 Watt - Side Load 3/8" - 18 NPT - 24 volt 1 $64.48
34146 Heater Kit - 100 Watt - Side Load 1/2" - 20 straight thread - 24 volt 1 $64.48
35334 Heater Kit - 100 Watt - Side Load - M12 x 1.5 - 24 volt 1 $64.48
29268 Water Sensor Kit - Conventional 12 volt 1 $95.18
33651 Water Sensor Kit - Conventional 24 volt 1 $147.48
29899 See-through water collection/storage bowl kit (not Marine) 1 $42.25
29578 Normal Flow Hand Primer Pump Kit (not Marine) 1 $30.72
29575 150 micron Pre-Filter Screen 6 $43.12
FM 100 Series Complete MARINE filter/separator assemblies, with special extra corrosion protection.
33643 Pre-filter Assy. with 3/8" NPT ports & 4.3" 150 micron marine element & marine drain 1 $61.90
33644 Pre-filter Assy. with 3/8" NPT ports & 4.3" 30 micron marine element & marine drain 1 $63.10
33645 Final filter Assy. with 3/8" NPT ports & 4.3" 5 micron marine element & marine drain 1 $64.15
FM 100 Series Header Assemblies for MARINE (Mounting Headers w/cap, volume plug, seals etc. No filter element.)
Use standard header kits (details on page 2)
FM 100 Series MARINE replacement elements (with special extra corrosion protection)
32200 150 micron Pre-filter Water Separator Element - 4.3" Marine 12 $262.08
32201 150 micron Pre-filter Water Separator Element - 6.0" Marine 12 $293.76
32177 30 micron Pre-filter Water Separator Element - 4.3" Marine 12 $252.60
32180 30 micron Pre-filter Water Separator Element - 6.0" Marine 12 $284.52
32178 5 micron Final Filter Water Separator Element - 4.3" Marine 12 $272.52
32179 5 micron Final Filter Water Separator Element - 6.0" Marine 12 $306.48
Page 3 of 6
Suggested
Part No. Description Pkg. Qty.
List Price
FM 100 ELEC. PURGE PUMP/FILTER SEPARATOR ASSY. for intermittent use with "Reverse Flow" configuration.
~ Unique REVERSE FLOW mounting header. Check arrows for correct inlet/outlet flow directions.
~ Must be used with REVERSE FLOW replacement elements, with BLACK logo. (See below)
~ Intended for use as a pre-filter/water separator assembly only.
~ Must also have a final (or secondary) filter e.g. 33642 between this pump/filter assembly and the engine.
~ This pump/filter/separator is available as complete unit only.
~ The Purge Pump module is NOT available as separate service module, and the electric
pump must NOT be installed on any other header unit. It is not seviceable.
~ In the event of pump failure, the complete unit (34301) must be replaced.
Replacement Elements - Special Reverse Flow configuration (Branded Fuel Manager in black)
150 micron Reverse Flow Pre-Filter/Water Separators
33962 150 micron Reverse Flow Pre-Filter Water Separator Element - 3.6" nominal length 12 $221.58
33963 150 micron Reverse Flow Pre-Filter Water Separator Element - 4.3" nominal length 12 $240.78
33965 150 micron Reverse Flow Pre-Filter Water Separator Element - 6.0" nominal length 12 $279.18
Reminder: The above "Reverse Flow" (black logo) elements must not be used on conventional Fuel
Manager assemblies; and conventional (red logo) elements must not be used on a "Reverse Flow"
header.
FM 100 Series Optional Module Kits for Purge Pump/Filter Separator Assembly.
Water sensor kit and side-load heater (See P3) can be used on integral Lift/Transfer Pump/Filter assemblies
Page 4 of 6
Suggested
Part No. Description Pkg. Qty.
List Price
FM 100 ELECTRIC LIFT PUMP/FILTER SEPARATOR ASSY. for constant use, with "Reverse Flow" configuration.
~ Unique REVERSE FLOW mounting header. Check arrows for correct inlet/outlet flow directions.
~ Must only be used with REVERSE FLOW replacement elements, with BLACK logo. (See below).
~ Can be used as FINAL filter/separator unit using 5-micron reverse flow element, or as
PRE-filter/separator unit, using 30-micron reverse flow element. Do not use 150-micron element.
~ If used as the only (FINAL) filter, it must have 5-micron reverse flow element. Can also be
used in combination with any pre-filter/water separator assembly "upstream".
~ If used as a PRE-filter unit, there must be a FINAL (5-micron) filter downstream.
~ This lift pump/filter/separator is available as a complete unit only.
~ The Lift Pump module is NOT available as separate service module, and the electric lift
pump must NOT be installed on any other header unit.
~ In the event of pump failure, the complete unit (33945) must be replaced.
FM 100 Series Replacement Elements - Special Reverse Flow configuration (Branded Fuel Manager in black)
5 micron Reverse Flow Final Filter/Water Separator elements.
33957 5 micron Reverse Flow Final Filter Water Separator Element - 2.8" nominal length 12 $213.05
33958 5 micron Reverse Flow Final Filter Water Separator Element - 3.6" nominal length 12 $232.25
33959 5 micron Reverse Flow Final Filter Water Separator Element - 4.3" nominal length 12 $251.45
33960 5 micron Reverse Flow Final Filter Water Separator Element - 5.1" nominal length 12 $270.65
33961 5 micron Reverse Flow Final Filter Water Separator Element - 6.0" nominal length 12 $289.85
Reminder: The above "Reverse Flow" (black logo) elements must not be used on conventional Fuel
Manager assemblies; and conventional (red logo) elements must not be used on a "Reverse Flow"
header.
FM 100 Series Optional Module Kits for Lift Pump/Filter Separator Assembly.
Water sensor kit and side-load heater (See Page 3) can be used on integral Lift/Transfer Pump/Filter assemblies
Page 5 of 6
Suggested
Part No. Description Pkg. Qty.
List Price
FM 1000 SERIES FUEL FILTER/WATER SEPARATORS
Suitable for diesel engines with up to 180 US galls/hr (680 liters/hr) total fuel flow (including return flow), or about 600 HP
FM 1000 Series Header only Assemblies (Header with cap, volume plug, seals etc.)
33564 FM 1000 header, black 'E' coated , with 1/2" - 14 NPTF thread ports 1 $135.60
33102 FM 1000 header, black 'E' coated , with 7/8" - 14 straight thread 'O' ring ports 1 $135.60
FM 1000 Series Replacement Elements for conventional normal flow assemblies (Branded FUEL MANAGER in red )
30 micron Pre-Filter/Water Separator Replacement Elements
33634 30 micron Pre-filter Water Separator Element - 4" nominal length 6 $155.52
33638 30 micron Pre-filter Water Separator Element - 8" nominal length 6 $184.32
Information & Promotion Material for all Fuel Manager Filter/Water Separators
99781 FM Full Line Color Brochure 1 N/C
99795 FM Users Guide 1 N/C
99769 FM Specification Summary 1 N/C
99441 FM 100 Series Display Model 1 $81.12
99440 FM 100 Series Display Banner 1 $5.71
Page 6 of 6