Professional Documents
Culture Documents
Lčkiuztr
Lčkiuztr
Lčkiuztr
ssssssssssssssssssssssssssss
ddddddddddddddddddddddddd
Sensor test devices
884 907 014 0 (~230 V)
884 011 158 0 (~115 V)
1st Edition
2007 WABCO
Table of Contents
Explanation of Symbols
Step
CAUTION Potentially hazardous situation which,
if not avoided, may result in minor or
moderate injury.
2
Description of the sensor test device Sensor test device 1
RS232 SAPP-5k
Main Controller Sensor Connector
WFCA
Resistance Module
RS232 IEEE-488
3
1 Sensor test device Description of the sensor test device
Front face
Select
884 907 014 0
1 2 Sensor Test Device
Single ON
4 3 5
Continuous
Back face
4
Function / operation Sensor test device 2
5
2 Sensor test device Function / operation
2.3 Measured value output The data can be logged with a monitor program
(e. g. Terminal.exe by Windows).
2.3.1 Display Transfer rate / data bits/ stop bits / parity /
Immediately after the measurement, the measured log: 19200 / 8 / 1 / - / - /
values are displayed in the following format:
Data string
W1= xxx.x Height uncompensated in [s] All capital letters and numbers are fixed designa-
charge time tions that cannot be changed.
W2= xxx.x Height uncompensated in [s] aaaabb<TAB>ccc<SPACE>ccc<SPACE>ccc
discharge time or 000.0 for <SPACE>c<TAB>W1<TAB>xxx.x<TAB>W2<TAB>
WFCA xxx.x<TAB>W3<TAB>xxx.x<TAB>R<TAB>xxxx.x
W3= xxxx.x Height compensated in [s] <CR><LF>
6
Special functions Sensor test device 3
3 Special functions
The special functions described below are not 3.2 Reading the saved compensation
designed for use in normal measuring operation. parameter file
They are designed for setting up and calibrating the
test device. (Push-button Select up)
If one of the two push-buttons is pressed within one The entire content of the compensation parameter
second of switching on the sensor test device, the file is output via the RS232 interface. The receipt of
device switches into a special mode. the data is not checked. After sending the data, the
test device switches into normal measuring mode.
Push-button 1 Output of the compensation The data can be received and displayed with a
Select parameter file via the RS232 monitor program (e. g. Terminal.exe by Windows).
Up interface
Push-button 1 Importing a compensation Send parameter P1
Select parameter file via the RS232
Down interface
Push-button 2
Calling up calibration routines
Single Transfer rate / data bits/ stop bits / parity / log:
Push-button 2 Selection of interface RS232 / 19200 / 8 / 1 / - / - /
Continuous IEC
Example of a file that contains data for all
sensor types:
3.1 Importing a new compensation 0x0000 (checksum)
Sensor test device 884 907 014 0 parameter file V1.00
parameter file WFCA01W=4410505300U=407O=0699I=158Y=178R=087.5
WFCA02W=4410505310U=407O=0699I=158Y=178R=087.5
(Push-button Select down) WOCA01W=0000000001U=999O=9999I=999Y=999R=999.9
WOCA02W=4411000010U=037O=0266I=098Y=200R=071.0
A new compensation parameter file can be
WISA01W=4411005390G=1.81A1=+0.020M1
imported via the RS232 interface. The data is =+0.600T1=9999A2=-0.000M2=-0.000T2
checked for validity and stored in the sensor test =0000A3=-0.000M3=-0.000T3=0000A4
=-0.000M4=-0.000T4=0000
device. If an error is detected in the data, an error WISA02W=4411000200G=1.58A1=-0.148M1
message is output. =+0.540T1=9999A2=-0.000M-0.000T2
=0000A3=-0.000M3=-0.000T3=0000A4=0.000M4
7
3 Sensor test device Special functions
8
Error messages Sensor test device 4
4 Error messages
4.1 Checking the parameter file Test WFCA WOCA WISA Explanation
. in the . Fixed
If a new parameter file is loaded to the sensor test -81 -82 -82
number character
device (see x.x), the plausibility of this file is
checked during the load process. If an error occurs, <CR>
<CR> -91 -92 -93
the process is interrupted and an error message is expected
output. Number 0-9
-101 -102 -103
s in row expected
Example:
A fixed
A - - -113
Error -32 /101 indicates character
Waiting for data...
Error message: -32 an error in the WOCA G fixed
G - - -123
Row: 101 parameter set in row character
101. M fixed
M - - -133
character
The last character indicates the error range
(sensor type). + or -
+- - - -143
expected
(0) = Undefined range
(1) = Error in WFCA range
4.2 Checking the internal
(2) = Error in WOCA range
communication with the data
(3) = Error in WISA range logger
List of all error messages
If the internal communication with the data logger
Test WFCA WOCA WISA Explanation does not work, the following error messages are
output:
Check- Checksum
-00 -00 -00
sum error
Sensor Test Device
WFCA,
Unknown
WOCA, -10 -10 -10 RS232 active
sensor type Error: Data logger
WISA
= fixed char-
= -11 -12 -13
acter
W fixed char- 4.3 Error in measuring with SAPP-5K
W -21 -22 -23 (WFCA)
acter
U fixed char-
U -31 -32 - If the internal communication with the SAPP-5K
acter
does not work, the following error messages are
O -41 -42 - O fixed error possible:
I fixed char-
I -51 -52 -
acter WFCA03 441 050 100 0
Open wire
Y fixed char-
Y -61 -62 -
acter
R fixed char-
R -71 -72 -
acter
9
4 Sensor test device Error messages
10
Technical data Sensor test device 5
5 Technical data
11
5 Sensor test device Technical data
12
ssssssssssssssssssssssssssss
ddddddddddddddddddddddddd
WABCO
WABCO WORLD-WIDE
WORLDWIDE