Professional Documents
Culture Documents
CH 01 Introduction To Valves PDF
CH 01 Introduction To Valves PDF
I Introduction to Valves
1.1. Valve
Valves are mechanical devices specifically designed to
direct, start, stop, mix, or regulate the flow, pressure,
or temperature of a process fluid.
Berdasarkan atas fungsinya, aplikasinya, dan
rancangannya, valve dapat dibedakan ke dalam
beragam kelas styles, sizes, dan ragam pressure.
Tipe yang umum ditemukan adalah plug, ball, globe,
butterfly, dan gate valves.
Valve dapat dibuat dari berbagai material seperti:
steel, iron, plastic, brass, atau sejumlah material
paduan khusus lainnya.
Komponen-komponen utama sebuah valve diberikan
pada Gbr. 1
Training on Valve Technology 2
1
Ch. I Introduction to Valves
The internal
elements of a valve
are collectively
referred to as a
valve's trim.
The trim typically
includes a disc,
seat, stem, and
sleeves needed to
guide the stem.
A valve's performa
nce is determined
by the disk and
seat interface and
the relation of the
disk position to the
seat.
Gbr. 2
Manual Valve Gbr.3
Control Valve
Training on Valve Technology 4
2
Ch. I Introduction to Valves
Gbr. 4
Ball Valve
Gbr. 5
Gate Valve
Gbr. 6
Plug Valve
Training on Valve Technology 5
Gbr. 7
Globe Valve
Gbr. 8
Butterfly Valve
Training on Valve Technology 6
3
Ch. I Introduction to Valves
4
Ch. I Introduction to Valves
1. On-off Valves
Terkadang juga disebut sebagai block valve.
Kelompok valve ini yang umum dijumpai: gate, plug,
ball, pressure relief, dan tank-bottom valves.
Jenis on-off valve umumnya hand-operated, walaupun
dapat diotomasi dengan tambahan aktuator.
Pressure-relief valves adalah self-actuated on-off
valves yang dapat terbuka hanya jika preset pressure
dilampaui (mencegah over pressuration).
Pressure-relief valves dibagi menjadi 2: Relief valves,
untuk aplikasi pada fluida cair dan safety valves,
untuk aplikasi pada fluida gas.
5
Ch. I Introduction to Valves
2. Non-return Valves
Nonreturn valves memungkinkan fluida untuk
mengalir ke suatu arah yang diinginkan (hanya satu
arah saja).
Semua check valves termasuk ke dalam kelompok
nonreturn valves.
Valve jenis ini digunakan untuk mencegah terjadinya
backflow yang tidak diinginkan.
Contoh aplikasi: untuk melindungi instalasi pompa
atau kompresor dari backflow saat shut down.
Nonreturn valves juga digunakan dalam sistem proses
dengan variasi tekanan yang harus dijaga secara
terpisah.
6
Ch. I Introduction to Valves
3. Throttling Valves
Valve jenis ini digunakan untuk mengatur aliran,
temperatur, atau tekanan.
Operasi throttling valves: manual (handwheel or
lever) atau dengan kontrol otomatis, Gbr. 13(a).
Pressure regulators adalah throttling valve yang
memvariasikan posisi valve untuk menjaga tekanan di
hilir valve tetap konstan, Gbr. 13(b)
Automatic control valves atau control valves is a term
commonly used to describe valves that capable of
varying flow conditions to match the process
requirements dilengkapi dengan actuator.
7
Ch. I Introduction to Valves
8
Ch. I Introduction to Valves
Manual Otomatis
9
Ch. I Introduction to Valves
10
Ch. I Introduction to Valves
11
Ch. I Introduction to Valves
1. Full-Port Size
12
Ch. I Introduction to Valves
2. Reduced-Port Size
13
Ch. I Introduction to Valves
Note:
PN is an approximation to the corresponding ANSI pressure class, and should
not be used as an exact correlation between two standards.
Training on Valve Technology 28
14
Ch. I Introduction to Valves
Reference
Skousen, P.L., Valve Handbook, McGraw-Hill, USA,
1998.
Fisher, Control Valve Handbook, Fisher Control
International, USA, 2001.
15