Professional Documents
Culture Documents
SKEMA
SKEMA
SKEMA
PANITIA KIMIA
SEKOLAH MENENGAH TEKNIK JOHOR BAHRU
PERATURAN PEMARKAHAN
1 (a)
Eksperimen A Eksperimen B
Pemerhatian pada Gelembung gas tidak berwarna Elektrod kuprum menjadi nipis
anod terbebas
The copper electrode becomes
Observation at the Colourless bubbles gas evolved thinner
anode
Pemerhatian pada Pepejal berwarna perang Elektrod kuprum menebal
katod terenap
The copper electrode becomes
Observation at the Brown solids deposited thicker
cathode
Hasil yang terbentuk Gas oksigen Ion kuprum(II), Cu2+
di anod
Oxygen gas Copper(II) ion, Cu2+
Products formed at
the anode
Hasil yang terbentuk Kuprum Kuprum
di katod
Copper Copper
Product formed at
the cathode
Setengah 4OH 2H2O + O2 + 4e Cu Cu2+ + 2e
persamaan di anod
(b)(i)
* Terminal negatif : Magnesium
Negative terminal : Magnesium
* Terminal positive : Kuprum
Positive terminal : Copper
2
* Arah pengaliran elektron : Mengalir daripada elektrod Magnesium ke elektrod Kuprum melalui
litar luar
Direction of electron flow : Flow from Magnesium electrode to copper electrode through external
wire
2. (a)(i) Saiz kalsium karbonat dalam Eksp II lebih kecil berbanding daripada Eksp I
The size of calcium carbonate in Experiment II is smaller than Experiment I
Jumlah luas permukaan kalsium karbonat yang terdedah kepada perlanggaran dalam
Eksperimen II adalah lebih besar
The total surface area of calcium carbonate exposed to collision in Experiment II is bigger
Frekuensi perlanggaran antara ion hidrogen dan kalsium karbonat dalam eksperimen II
lebih tinggi.
Frequency of collision between hydrogen ion and calcium carbonate in experiment II is
higher
Maka kadar tindak balas bagi Eksperimen II adalah lebih tinggi daripada Eksperimen I
Thus, the rate of reaction for Experiment II is higher than Experiment I
(iii) Kecerunan tangen ditunjukkan dengan betul pada t= 90s pada lengkung I dan lengkung II.
Correct gradient of tangent drawn at t = 90s in Curve I and Curve II.
Kadar tindak balas pada masa 90 s Eksp I = kecerunan tangen = 43 20 = 0.11 cm3 s-1
Instantaneous rate of reaction at 90 s Exp I gradient of tangent 202.5 0
Kadar tindak balas pada masa 90 s Eksp II = kecerunan tangen = 44 20 = 0.15 cm3 s-1
Instantaneous rate of reaction at 90 s Exp II gradient of tangent 162 0
5
(b) 1. Tambahkan serbuk magnesium secara berlebihan ke dalam 25 cm3 asid hidroklorik
1 mol dm-3
Add excess magnesium powder with 25 cm3 of 1 mol dm-3 hydrochloric acid
2. Pada suhu yang sama
At the same temperature
Atau /or
(c) Kadar tindak balas yang menggunakan asid sulfurik adalah lebih tinggi
Rate of reaction using sulphuric acid is higher
Asid sulfurik adalah asid dwibes dan bilangan mol ion H+ adalah dua kali ganda.
Sulphuric acid is diprotic acid and the number of mole of H+ ion is doubled
Maka, Isi padu maksimum gas yang terkumpul adalah dua kali ganda lebih tinggi
Therefore, maximum volume of gas collected is doubled
The electron arrangement of atom Y is 2.8.1. The electron arrangement of atom Z is 2.8.7
Susunan elektron atom Y adalah 2.8.1. Susunan elektron atom Z adalah 2.8.7.
Atom Y release 1 electron to achieve a stable octet electron arrangement. Y+ ion is formed.
Atom Y mendermakan 1 elektron untuk mencapai susunan elektron oktet yang stabil. Ion Y +
terbentuk.
Atom Z accept 1 electron to achieve a stable octet electron arrangement. Z ion is formed.
Atom Z menerima 1 elektron untuk mencapai susunan elektron oktet yang stabil. Ion Z terbentuk.
Y +
ion and Z ion are attracted to each other by strong electrostatic force.
Ion Y +
dan ion Z ditarik antara satu sama lain oleh daya elektrostatik yang kuat.
The electron arrangement of atom X is 2.4. The electron arrangement of atom Z is 2.8.7
Susunan elektron atom X adalah 2.4. Susunan elektron atom Z adalah 2.8.7.
Atom X needs 4 more electrons. Therefore atom X contributes 4 electrons for sharing.
Atom X memerlukan 4 lagi elektron. Maka, atom X menyumbangkan 4 elektron untuk
perkongsian.
Atom Z needs 1 more electron. Therefore, atom Z contributes 1 electron for sharing.
Atom Z memerlukan 1 lagi elektron. Maka, atom Z menyumbangkan 1 elektron untuk perkongsian.
One atom X shares 1 pair of electron each with four atom Z to achieve stable octet electron
arrangement.
Satu atom X berkongsi 1 pasang elektron setiap satu dengan empat atom Z untuk mencapai
susunan elektron oktet yang stabil.
(ii) Acid A / Hydochloric acid is a strong acid which ionises completely in water to form high
concentration of hydrogen ion.
Acid A / asid hidroklorik adalah asid kuat yang mengion lengkap dalam air menghasilkan
kepekatan ion hidrogen yang tinggi.
Acid B / ethanoic acid is a weak acid which ionises partially in water to form low concentration of
hydrogen ion.
Acid B / asid etanoik adalah asid lemah yang mengion separa dalam air menghasilkan kepekatan
ion hidrogen yang rendah.
The concentration of hydrogen ion in acid A / hydrochloric acid is higher than acid B / ethanoic
acid.
Kepekatan ion hidrogen dalam asid A / asid hidroklorik lebih tinggi daripada asid B / asid etanoik.
The higher the concentration of hydrogen ion in acid A / hydrochloric acid, the lower the pH value.
Semakin tinggi kepekatan ion hidrogen dalam asid A / asid hidroklorik, semakin rendah nilai pH.
(ii) Ammonia ionises in solvent X / water to form freely moving ions. The presence of freely moving
ions can conduct electricity.
Ammonia mengion dalam pelarut X / air menghasilkan ion-ion bebas bergerak. Kehadiran ion-ion
bebas bergerak boleh mengkonduksikan elektrik.
Ammonia does not ionise in solvent Y / methyl benzene. Ammonia remains as neutral molecules
and cannot conduct electricity.
Ammonia tidak mengion di dalam pelarut Y / metil benzena. Ammonia kekal dalam bentuk molekul
neutral dan tidak mengkonduksikan elektrik.
(d)(i) Nitrogen
Nitrogen
(ii) Percentage of nitrogen in (NH4)2SO4 = 2 x 14 x 100 = 21.21 %
Peratus nitrogen dalam (NH4)2SO4 2(18) + 32 + 4(16)
Urea is the better fertiliser because the percentage of nitrogen by mass is higher.
Urea adalah baja yang lebih baik kerana peratus nitrogen mengikut jisim lebih tinggi.
Q: Consists of ions
Mengandungi ion
The ions are attracted to each other by strong electrostatic forces
Ion-ion ditarik antara satu sama lain oleh daya elektrostatik yang kuat
More heat energy is needed to overcome the forces
Lebih banyak tenaga haba diperlukan untuk mengatasi daya tersebut
The electron arrangement of atom Z is 2.8.2. The electron arrangement of atom Y is 2.7
Susunan elektron atom Z adalah 2.8.2. Susunan elektron atom Y adalah 2.7.
Atom Z release 2 electrons to achieve a stable octet electron arrangement. Z2+ ion is formed.
Atom Z mendermakan 2 elektron untuk mencapai susunan elektron oktet yang stabil. Ion Z 2+
terbentuk.
Atom Y accept 1 electron to achieve a stable octet electron arrangement. Y ion is formed.
Atom Y menerima 1 elektron untuk mencapai susunan elektron oktet yang stabil. Ion Y
terbentuk.
Z 2+
ion and Y ion are attracted to each other by strong electrostatic force.
Ion Z 2+ dan ion Y ditarik antara satu sama lain oleh daya elektrostatik yang kuat.
The electron arrangement of atom X is 2.4. The electron arrangement of atom Y is 2.7
Susunan elektron atom X adalah 2.4. Susunan elektron atom Y adalah 2.7.
Atom X needs 4 more electrons. Therefore atom X contributes 4 electrons for sharing.
Atom X memerlukan 4 lagi elektron. Maka, atom X menyumbangkan 4 elektron untuk
perkongsian.
Atom Y needs 1 more electron. Therefore, atom Y contributes 1 electron for sharing.
Atom Y memerlukan 1 lagi elektron. Maka, atom Y menyumbangkan 1 elektron untuk perkongsian.
10
One atom X shares 1 pair of electron each with four atom Y to achieve stable octet electron
arrangement.
Satu atom X berkongsi 1 pasang elektron setiap satu dengan empat atom Y untuk mencapai
susunan elektron oktet yang stabil.
(c)(i)
7. (a)(i) Ethanol
Etanol
Properties:
Sifat-sifat:
1. Miscible in water
Terlarutcampur dalam air
2. Colourless liquid
Cecair tak berwarna
3. Low melting and boiling point
Takat lebur dan didih yang rendah
4. Highly volatile // easy to evaporate
Sangat mudah meruap // mudah menyejat
5. Cannot conduct electricity in any state
Tidak mengkonduksikan elektrik dalam semua keadaan.
(ii)
Name of the reaction : Esterification
Nama tindak balas tersebut: Pengesteran
Chemical equation: C2H5COOH + C2H5OH C2H5COOC2H5 + H2O
Persamaan kimia:
The name of the ester: Ethyl propanoate
nama ester yang terhasil: Etil propanoat
Structural formula of the ester:
Formula struktur bagi ester:
(b) (i) Heat change when 1 mol of silver chloride precipitate is formed from the reaction
between silver nitrate solution and potassium chloride solution.
Perubahan haba apabila 1 mol mendakan argentum klorida terbentuk daripada tindak balas
antara larutan argentum nitrat dan larutan kalium klorida.
(ii)
13
(iii) No of mol AgCl = no of mol AgNO3 / KCl = M V = 0.5 (20) = 0.01 mol
Bil mol AgCl = bil mol AgNO3 / KCl 1000 1000
H = - 65.5 kJ mol-1
Heat released, H = m c
Haba terbebas, H
655 = (20 + 20) (4.2)
= 3.9 C
Because the reaction still produce the same 1 mol of AgCl precipitate.
Kerana tindak balas masih membentuk 1 mol mendakan AgCl yang sama.
(iii) Process Z:
Proses Z:
Mix nitrogen gas and hydrogen gas in the ratio of N:H = 1:3
Campurkan gas nitrogen dan gas hidrogen dalam nisbah N:H = 1:3
Conditions required for the reaction:
Keadaan yang diperlukan semasa tindak balas:
Temperature / Suhu : 450C
Pressure / Tekanan : 200 atm
Catalyst / Mangkin : Iron / Ferum
Chemical equation : N2 + 3H2 2NH3
Persamaan kimia:
14
(b) *Soap is dissolved in water to reduce the surface tension of water so that the water easily
wet the dirty cloth.
Sabun dilarutkan di dalam air untuk mengurangkan tegangan permukaan air supaya air mudah
membasahkan kain yang kotor.
*Soap anion consists of hydrophobic part and hydrophilic part.
Anion sabun mengandungi bahagian hidrofobik dan bahagian hidrofilik.
*Hydrophobic parts dissolve in grease (dirts) whereas hydrophilic parts dissollve in water
Bahagian hidrofobik melarut di dalam gris (kotoran) manakala bahagian hidrofilik melarut dalam
air
* During rubbing / scrubbing, the grease is loosened and lifted off from the cloth.
Semasa menggosok / menyental, gris ditanggalkan daripada kain.
* The grease forms smaller droplets (emulsion) and suspended in water.
Gris membentuk titisan kecil (emulsi) dan terampai di dalam air.
* The grease droplets are negatively charged and repel each other so that the grease do not
redeposit on the cloth.
Titisan gris bercas negatif dan menolak antara satu sama lain supaya gris tidak terenap pada
kain semula.
*Rinsing with water removes the grease droplets together with soap foams.
Membilas dengan air menyingkirkan titisan gris bersama-sama dengan buih sabun.
(c)
Types of medicine Function
Jenis ubat Fungsi
Analgesics To relieve pain.
Analgesik Melegakan kesakitan.
Antibiotic To kill or inhibit the growth of infectios bacteria
Antibiotik Membunuh atau merencatkan pembiakan bakteria pembawa penyakit
Psychotherapeutic To control symptoms of mental ilness
Psikoterapeutik Untuk mengawal gejala penyakit mental
15
Salt (NaCl)
Garam (NaCl)
Susunan elektron atom natrium adalah 2.8.1 dan susunan elektron atom klorin adalah 2.8.7.
-Sodium atom releases one electron to achieve stable octet electron arrangement. Sodium ion,
Na+ is formed.
Atom natrium mendermakan satu elektron untuk mencapai susunan elektron oktet yang stabiil.
Ion natrium, Na+ terbentuk.
-Chlorine atom receives one electron to achieve stable octet electron arrangement. Chloride ion,
Cl is formed.
Atom klorin menerima satu elektron untuk mencapai susunan elektron oktet yang stabiil. Ion
klorida, Cl terbentuk.
-Sodium ion, Na+ and chloride ion, Cl are attracted to each other by a strong electrostatic force
of attraction.
Ion natrium, Na+ dan ion klorida, Cl ditarik antara satu sama lain oleh daya elektrostatik yang
kuat.
-An ionic compound with formula of NaCl is formed.
Sebatian ion dengan formula NaCl terbentuk.
(ii) Table salt/ sodium chloride can conduct electricity in solvent W/ water.
Garam / natrium klorida boleh mengkonduksi elektrik dalam pelarut W / air.
Because table salt/ sodium chloride in solvent W (water) exists as free moving ions.
Kerana garam / natrium klorida di dalam pelarut W (air) wujud sebagai ion-ion bebas bergerak.
Table salt/ sodium chloride in solvent X (methyl benzene) cannot conduct electric.
Garam / natrium klorida dalam pelarut X (metil benzena) tidak boleh mengkonduksikan elektrik.
Because table salt/ sodium chloride in solvent X (methyl benzene) has no free moving ions/ ions
in a fix position / Table salt cannot dissolve in solvent X (methyl benzene).
Kerana garam / natrium klorida dalam pelarut X (metil benzena) tiada ion-ion yang bebas bergerak
/ ion-ion dalam kedudukan yang tetap / garam tidak melarut dalam pelarut X (metilbenzena).
Mass of NH4Cl that has not been reacted = 3.0 0.13375 = 2.866 g
Jisim NH4Cl yang belum bertindak balas
Acid Q : hydrochloric acid // nitric acid // sulphuric acid (any name of strong acid)
Asid Q : Asid hidroklorik // asid nitrik // asid sulfurik (nama mana-mana asid kuat)
(ii) Set I:
Acid P / ethanoic acid is a weak acid.
Asid P / asid etanoik adalah asid lemah.
Acid P / ethanoic acid ionises partially in water to form lower concentration of hydrogen ion.
Asid P / asid etanoik mengion separa dalam air menghasilkan kepekatan ion hidrogen yang lebih
rendah.
Lower number of hydrogen ions release lower volume of carbon dioxide gas.
Bilangan ion hidrogen yang lebih rendah membebaskan isi padu gas karbon dioksida yang lebih
rendah.
Lower volume of carbon dioxide takes longer time for the lime water to turn chalky.
Isi padu gas karbon dioksida yang lebih rendah mengambil masa yang lebih panjang untuk
mengeruhkan air kapur.
The rate of reaction is lower.
Kadar tindak balas lebih rendah.
Set II:
Acid Q / hydrochloric acid is a strong acid.
Asid Q / asid hidroklorik adalah asid kuat.
Acid Q / hydrochloric acid ionises completely in water to form higher concentration of hydrogen
ions.
Asid Q / asid hidroklorik mengion lengkap dalam air menghasilkan kepekatan ion hidrogen yang
lebih tinggi.
Higher number of hydrogen ions release higher volume of carbon dioxide gas.
Bilangan ion hidrogen yang lebih tinggi membebaskan isi padu gas karbon dioksida yang lebih
tinggi.
Higher volume of carbon dioxide gas takes shorter time for the lime water to turn chalky.
Isi padu gas karbon dioksida yang lebih tinggi mengambil masa yang lebih singkat untuk
mengeruhkan air kapur.
The rate of reaction is higher.
Kadar tindak balas lebih tinggi.
18
(ii)
(ii) Butan-1-ol is better fuel because the fuel value is higher // 1 g of the fuel releases 36.1 kJ of
heat energy.
Butan-1-ol adalah bahan api yang lebih baik kerana nilai bahan api lebih tinggi // 1 g bahan api
membebaskan 36.1 kJ tenaga haba.
12. (a)
Compound formed between X and Y Compound formed between Z and Y
Sebatian terbentuk antara X dan Y Sebatian terbentuk antara Z dan Y
Types of chemical Ionic bond. Covalent bond.
bond Ikatan ion. Ikatan kovalen.
Jenis ikatan kimia
Boiling point and *High. * Low
melting point Tinggi. Rendah
Takat didih dan *The ions are attracted to each *The molecules are attracted to
takat lebur other by strong electrostatic force. each other by weak intermolecular
Ion-ion ditarik antara satu sama lain forces.
oleh daya elektrostatik yang kuat. Molekul molekul ditarik oleh daya
* More heat energy is needed to antara molekul yang lemah.
overcome the forces. *Less heat energy is needed to
Lebih banyak tenaga haba overcome the forces.
diperlukan untuk mengatasi daya Sedikit tenaga haba diperlukan untuk
tersebut. mengatasi daya tersebut.
(b)
The electron arrangement of atom X is 2.8.2. The electron arrangement of atom Y is 2.6.
Susunan elektron atom X adalah 2.8.2. Susunan elektron atom Y adalah 2.6.
Atom X release 2 electrons to achieve a stable octet electron arrangement. X2+ ion is formed.
Atom X mendermakan 2 elektron untuk mencapai susunan elektron oktet yang stabil. Ion X 2+
terbentuk.
Atom Y accept 2 electron to achieve a stable octet electron arrangement. Y2- ion is formed.
Atom Y menerima 2 elektron untuk mencapai susunan elektron oktet yang stabil. Ion Y2-
terbentuk.
X2+ ion and Y2- ion are attracted to each other by strong electrostatic force.
Ion X 2+ dan ion Y2- ditarik antara satu sama lain oleh daya elektrostatik yang kuat.
20
Apparatus: crucible, pipe-clay triangle, tripod stand, Bunsen burner, connecting wire, switch, 2
dry cells, bulb.
Radas: mangkuk pijar, segi tiga tanah liat, tungku kaki tiga, penunu Bunsen, wayar penyambung,
suis, 2 sel kering, mentol.
Procedure:
Prosedur:
1. Fill a crucible with solid naphthalene (P) until it is half full.
Isikan pepejal naftalena (P) ke dalam mangkuk pijar sehingga separuh penuh.
2. Dip two carbon electrodes into the naphthalene
Celupkan dua elektrod karbon ke dalam naftalena.
3. Connect both carbon electrode to a switch, dry cells and bulb using connecting wire.
Sambungkan kedua-dua elektrod karbon kepada suis, sel kering dan mentol menggunakan
wayar penyambung.
4. Turn on the switch and record the observation before heating.
Hidupkan suis dan rekodkan pemerhatian sebelum pemanasan.
5. Heat solid naphthalene (P) strongly until its melt completely.
Panaskan pepejal naftalena (P) dengan kuat sehingga melebur dengan lengkap.
6. Turn on the switch again and record the observation during heating.
Hidupkan suis sekali lagi dan rekodkan pemerhatian semasa pemanasan.
7. Repeat steps 1 to 6 using solid lead(II) bromide (Q) to replace solid naphthalene(P).
Ulangi langkah 1 hingga 6 menggunakan pepejal plumbum(II) bromida (Q) bagi menggantikan
pepejal naftalena (P).
21
Observation:
Pemerhatian:
Compound Physical state Observation
Sebatian Keadaan fizik Pemerhatian
naphthalene Solid Bulb does not light up
naftalena Pepejal Mentol tidak menyala
Molten Bulb does not light up
Leburan Mentol tidak menyala
lead(II) bromide Solid Bulb does not light up
plumbum(II) bromida Pepejal Mentol tidak menyala
Molten Bulb lights up
Leburan Mentol menyala
Conclusion:
Kesimpulan:
Naphthalene is covalent compound. Naphthalene cannot conduct electricity in any state.
Naftalena adalah sebatian kovalen. Naftalena tidak mengkonduksikan elektrik dalam semua
keadaan.
Lead(II) bromide is ionic compound. Lead(II) bromide cannot conduct electricity in solid state but
can conduct electricity in molten state.
Plumbum(II) bromida adalah sebatian ion. Plumbum(II) bromida tidak mengkonduksikan elektrik
dalam keadaan pepejal tetapi mengkonduksikan elektrik dalam keadaan leburan.
13. (a)(i) The electron arrangement of sodium atom, Na = 2.8.1 and chlorine atom, Cl =
2.8.7.
Susunan elektron atom natrium, Na = 2.8.1 dan atom klorin, Cl = 2.8.7.
Both atoms have 3 shells occupied with electrons.
Kedua-dua atom mempunyai 3 petala berisi elektron.
Sodium atom, Na and chlorine atom, Cl are located in Period 3.
Atom natrium, Na dan atom klorin, Cl terletak dalam Kala 3.
The number of valence electrons of sodium atom, Na is 1, so it is located in Group 1.
Bilangan elektron valens atom sodium, Na ialah 1, maka ia terletak dalam Kumpulan 1.
The number of valence electrons of chlorine atom, Cl is 7 so it is located in Group 17.
Bilangan elektron valens atom chlorine atom, Cl ialah 1, maka ia terletak dalam Kumpulan
17.
-Sodium ion, Na+ and chloride ion, Cl are attracted to each other by a strong electrostatic force
of attraction.
Ion natrium, Na+ dan ion klorida, Cl ditarik antara satu sama lain oleh daya elektrostatik yang
kuat.
-An ionic compound with formula of NaCl is formed.
Sebatian ion dengan formula NaCl terbentuk.
Compound in (a)(ii) / NaCl consists of ions which are held together by strong electrostatic
force.
Sebatian dalam (a)(ii) / NaCl mengandungi ion-ion yang ditarik oleh daya elektrostatik yang
kuat.
More heat energy is needed to overcome the forces.
Lebih banyak tenaga haba diperlukan untuk mengatasi daya tersebut.
14. (a)(i)
Type of food additive Function
Jenis bahan tambah makanan Fungsi
Thickener To thicken food.
Pemekat Untuk memekatkan makanan.
Preservative To slow down / to prevent the growth of microorganisms
Bahan pengawet Untuk melambatkan / manghalang pembiakan
mikroorganisma
Antioxidant To prevent oxidation of foods.
23
(ii) Advantage:
Kebaikan:
Make food stay fresh longer.
Makanan tahan lebih lama.
Make food look nicer.
Makanan nampak lebih menarik.
Make food taste better.
Makanan rasa lebih baik.
Disadvantage:
Keburukan:
Able to cause serious diseases like cancer and asthma.
Boleh menyebabkan penyakit berbahaya seperti barah/kanser dan asma.
Able to cause allergy.
Boleh menyebabkan allergi / alahan.
(iii)
Mahmud Ah Seng
Type of medicine: Type of medicine:
Jenis ubat: Jenis ubat:
Antibiotic / Antibiotik Analgesic / analgesik
1. (a)(i) Asid monobes ialah asid yang mengion dalam air untuk menghasilkan 1 mol ion
hidrogen.
Monoprotic acid is an acid that ionise in water to produce 1 mol of hydrogen ion.
Asid dwibes ialah asid yang mengion dalam air untuk menghasilkan 2 mol ion hidrogen.
Diprotic acid is an acid that ionise in water to produce 2 mol of hydrogen ion.
(ii)
Asid sulfurik Asid hidroklorik
Sulphuric acid Hydrochloric acid
Bilangan mol H2SO4 = M V = 1 (50) Bilangan mol HCl = M V = 1(50)
No of mol H2SO4 1000 1000 No of mol HCl 1000 1000
= 0.05 mol = 0.05 mol
1 mol H2SO4 mengion kepada 2 mol ion H+ 1 mol HCl mengion kepada 1 mol H+
1 mol H2SO4 ionises to 2 mol ion H+ 1 mol HCl ionises to 1 mol H+
0.05 mol H2SO4 mengion kepada 0.1 mol H+ 0.05 mol HCl mengion kepada 0.05 mol H+
0.05 mol H2SO4 ionises to 0.1 mol ion H+ 0.05 mol HCl ionises to 0.05 mol H+
Bilangan ion hidrogen dalam kedua-dua asid dengan kepekatan yang sama adalah dua kali
ganda dalam asid sulfurik dibandingkan dengan asid hidroklorik.
Number of hydrogen ion in both acids with the same concentration is doubled in sulphuric acid
compared to hydrochloric acid.
25
Kesimpulan:
Conclusion:
Asid sulfurik adalah asid dwibes di mana 1 mol asid sulfurik mengion kepada 2 mol ion hidrogen
manakala asid hidroklorik adalah asid monobes di mana 1 mol asid hidroklorik mengion kepada
1 mol ion hidrogen.
Sulphuric acid is a diprotic acid in which 1 mol sulphuric acid ionises to form 2 mol hydrogen ion
whereas hydrochloric acid is a monoprotic acid in which 1 mol of hydrochloric acid ionises to
form 1 mol hydrogen ion.
Jisim NaOH = bil mol x jisim molar = 0.25 x [1(23) + 1(16) + 1(1)]
Mass of NaOH no of mol x molar mass = 0.25 x 40 = 10 g
Kaedah :
Procedure:
1. Timbang 10 g natrium hidroksida dengan tepat di dalam sebuah bikar kecil menggunakan
penimbang elektronik.
Weigh exactly 10 g of sodium hydroxide in a small beaker using electronic balance.
2. Tambahkan sedikit air suling ke dalam bikar dan kacau dengan menggunakan rod kaca.
Add a little distilled water into the beaker and stir using glass rod.
3. Masukkan larutan ini ke dalam kelalang volumetrik 250 cm3 menggunakan corong turas.
Pour the solution into a 250 cm3 volumetric flask using filter funnel.
4. Bilas bikar dan corong turas dengan air suling beberapa kali dan masukkan air bilasan ini ke
dalam kelalang volumetrik.
Rinse the beaker and filter funnel with distilled water several times and transfer all the solution
into volumetric flask.
5. Tutupkan kelalang volumetrik dengan penutup dan goncang sehingga semua natrium
hidroksida larut.
Close the volumetric flask using stopper and shake the flask until sodium hydroxide dissolves
completely.
6. Tambahkan air suling secara perlahan sehingga mencapai tanda senggatan pada kelalang
volumetrik.
Add distilled water slowly until it reaches the graduation mark of the volumetric flask.
7. Kelalang ditutup semula dan digoncang beberapa kali supaya larutan bercampur dengan
lengkap.
Close the flask with stopper again and shake the flask several times.
8. Larutan yang diperoleh adalah larutan natrium hidroksida yang berkepekatan 1.0 mol dm-3
dengan isipadu 250 cm3.
Standard sodium hydroxide solution of volume 250 cm3 with concentration of 1.0 mol dm-3 is
formed.
26
Heksena menghasilkan lebih banyak jelaga kerana peratus karbon mengikut jisim lebih tinggi
berbanding heksana.
Hexene produces more soot because the percentage of carbon by mass is higher compared to
hexane.
(b)
Bilangan mol C4H9OH = jisim = mass = 3.7 = 3.7 = 0.05 mol
No of mol jisim molar Molar mass 4(12) + 1(10) + 16 74
0.05 mol C4H9OH terbakar menghasilkan 0.05 x 2678 = 133.9 kJ = 133 900 J
0.05 mol C4H9OH burnt release 1
(c) Apparatus : Copper container, thermometer, measuring cylinder, tripod stand, spirit lamp,
windshields, electronic balance
Radas : Bekas kuprum, termometer, silinder penyukat, tungku kaki tiga, lampu pelita,
penghadang angin, penimbang elektronik
Diagram / Rajah:
27
Procedure:
Prosedur:
1. Measure 200 cm3 of water using measuring cylinder and is poured into a copper container.
Sukat 200 cm3 air dengan menggunakan silinder penyukat dan dituangkan ke dalam bekas
kuprum.
2. Record the initial temperature of water using thermometer, T1
Rekodkan suhu awal air menggunakan termometer, T1
3. Fill a spirit lamp with butanol until half full
Isikan sebuah lampu pelita dengan butanol sehingga separuh penuh.
4. Weigh the spirit lamp and its content using electronic balance and record its mass, m1.
Timbangkan lampu pelita dan kandungannya menggunakan penimbang elektronik dan jisim
direkodkan, m1.
5. Place the spirit lamp under the copper container as closed as possible and the wick is ignited.
Letakkan lampu pelita diletakkan di bawah bekas kuprum sedekat yang mungkin dan sumbu
pelita dinyalakan.
6. Stir the water continuously.
Kacaukan air berterusan.
7. When the temperature of water is increases by 30 oC, the flame is put off.
Apabila suhu air meningkat sebanyak 30 oC, lampu pelita dipadam.
8. Weigh the spirit lamp and its content immediately, and the mass is recorded, m2.
Timbangkan lampu pelita dan kandungannya serta-merta, dan jisim direkodkan, m2.
Tabulation of data:
Penjadulan data:
Suhu awal air /oC
T1
Initial temperature of water /oC
Suhu tertinggi air /oC
T2
Highest temperature of water /oC
Perubahan suhu /oC
T2 T1
Temperature rise /oC
Jisim awal butanol + lampu pelita /g
m1
Initial mass of butanol + spirit lamp /g
Jisim akhir butanol + lampu pelita /g
m2
Final mass of butanol + spirit lamp /g
Jisim butanol terbakar /g
m1 m2
Mass of butanol burnt /g
Calculation/ pengiraan :
3. (a) At anode:
Di anod:
Products: Oxygen gas (and water)
Hasil: Gas oksigen (dan air)
At Cathode:
Di katod:
Product: Hydrogen gas
Hasil: Gas hidrogen
(b)
Cell X / Sel X Cell Y / Sel Y
Energy change Chemical energy to electrical Electrical energy to chemical
Perubahan tenaga energy energy
Tenaga kimia kepada tenaga Tenaga elektrik kepada
elektrik tenaga kimia
Terminal Negative: Zinc Cathode: Copper
Terminal Negatif: zink Katod: Kuprum
Positive: Copper Anode: Copper
Positif: kuprum Anod: Kuprum
Half equation at positive Cu 2+
+ 2e Cu Cu Cu2+ + 2e
terminal
Setengah persamaan di
terminal positif
Half equation at negative Zn Zn2+ + 2e Cu2+ + 2e Cu
terminal
Setengah persamaan di
terminal negatif
Observation at positive Copper becomes thicker Copper becomes thinner
terminal Kuprum semakin menebal Kuprum semakin menipis
Pemerhatian di terminal
positif
Observation at negative Zinc becomes thinner Copper becomes thicker
terminal Zink semakin menipis Kuprum semakin menebal
Pemerhatian di terminal
negatif
29
(c) Materials: Magnesium ribbon, copper strip, 1 mol dm-3 lead(II) nitrate solution, sand paper.
Bahan: Pita magnesium, jalur kuprum, 1 mol dm-3 larutan plumbum(II) nitrat, kertas pasir.
Procedure:
Prosedur:
1. Clean magnesium ribbon using sand paper.
Bersihkan pita magnesium menggunakan kertas pasir.
2. Pour 5 cm3 of 1 mol dm-3 lead(II) nitrate solution into a test tube.
Tuangkan 5 cm3 larutan plumbum(II) nitrat 1 mol dm-3 ke dalam sebuah tabung uji.
3. Drop the magnesium ribbon into the solution.
Masukkan pita magnesium ke dalam larutan.
4. Record the observation.
Rekodkan pemerhatian.
5. Repeat steps 1 to 4 using copper strip.
Ulangi langkah 1 hingga 4 menggunakan jalur kuprum.
Observation:
Pemerhatian:
Metal and solution Observation
Logam dan larutan Pemerhatian
Magnesium + Lead(II) nitrate solution Deposit formed
Magnesium + larutan plumbum(II) nitrat Enapan terbentuk
Copper + Lead(II) nitrate solution No change
Kuprum + larutan plumbum(II) nitrat Tiada perubahan
Magnesium (more electropositive metal) can displace lead (less electropositive metal) from
lead(II) nitrate solution.
Magnesium (logam lebih elektropositif) boleh menyesarkan plumbum (logam kurang
elektropositif) daripada larutan plumbum(II) nitrat.
(ii) Use electrical appliances that use energy efficiently (energy saving appliances)
Gunakan alatan elektrik yang menggunakan tenaga dengan cekap ( alatan jimat tenaga)
- Unplug appliances that are not in use.
Cabutkan plug peralatan yang tidak digunakan.
- Replace regular bulb with LED bulbs
Gantikan mentol biasa kepada mentol LED
(c) Apparatus : Copper container, thermometer, measuring cylinder, tripod stand, spirit lamp,
windshields, electronic balance
Radas : Bekas kuprum, termometer, silinder penyukat, tungku kaki tiga, lampu pelita,
penghadang angin, penimbang elektronik
Diagram / Rajah:
31
Procedure:
Prosedur:
1. Measure 200 cm3 of water using measuring cylinder and is poured into a copper container.
Sukat 200 cm3 air dengan menggunakan silinder penyukat dan dituangkan ke dalam bekas
kuprum.
2. Record the initial temperature of water using thermometer, T1
Rekodkan suhu awal air menggunakan termometer, T1
3. Fill a spirit lamp with ethanol until half full
Isikan sebuah lampu pelita dengan etanol sehingga separuh penuh.
4. Weigh the spirit lamp and its content using electronic balance and record its mass, m1.
Timbangkan lampu pelita dan kandungannya menggunakan penimbang elektronik dan jisim
direkodkan, m1.
5. Place the spirit lamp under the copper container as closed as possible and the wick is ignited.
Letakkan lampu pelita diletakkan di bawah bekas kuprum sedekat yang mungkin dan sumbu
pelita dinyalakan.
6. Stir the water continuously.
Kacaukan air berterusan.
7. When the temperature of water is increases by 30 oC, the flame is put off.
Apabila suhu air meningkat sebanyak 30 oC, lampu pelita dipadam.
8. Weigh the spirit lamp and its content immediately, and the mass is recorded, m2.
Timbangkan lampu pelita dan kandungannya serta-merta, dan jisim direkodkan, m2.
Tabulation of data:
Penjadulan data:
Suhu awal air /oC
T1
Initial temperature of water /oC
Suhu tertinggi air /oC
T2
Highest temperature of water /oC
Perubahan suhu /oC
T2 T1
Temperature rise /oC
Jisim awal ethanol + lampu pelita /g
m1
Initial mass of etanol + spirit lamp /g
Jisim akhir etanol + lampu pelita /g
m2
Final mass of ethanol + spirit lamp /g
Jisim etanol terbakar /g
m1 m2
Mass of ethanol burnt /g
Calculation/ pengiraan :
(ii)
Information: Maklumat:
The reaction is exothermic // the reaction releases heat energy to surrounding
Tindak balas adalah eksotermik // tindak balas membebaskan tenaga haba ke persekitaran
Temperature of the surrounding (solution) increases.
Suhu persekitaran ( larutan) bertambah.
Total energy content of reactants (KOH and HX) is higher the the total energy content of
products (KX and H2O)
Jumlah kandungan tenaga bahan tindak balas (KOH dan HX) adalah lebih tinggi daripada
jumlah kandungan tenaga hasil tindak balas (KX dan H2O)
When 1 mol KOH reacts with 1 mol HX to produce 1 mol KX and 1 mol H2O, 54 kJ of heat is
released.
Apabila 1 mol KOH bertindak balas dengan 1 mol HX untukmenghasilkan 1 mol KX dan 1 mol
H2O, 54 kJ tenaga haba dibebaskan.
Procedure/kaedah :
1. Measure 25 cm3 of 0.2 mol dm-3 copper (II) sulphate solution using measuring cylinder and
pour into a polystyrene cup.
33
Sukat 25 cm3 larutan kuprum (II) sulfat 0.2 mol dm-3 menggunakan silinder penyukat dan
tuangkan ke dalam cawan polistirena.
2. Place the thermometer into the polystyrene cup and record the initial temperature of the
solution, T1
Letakkan thermometer ke dalam cawan polistirena dan rekodkan suhu awal larutan, T1
3. Add 1 g of zinc powder quickly and carefully into the polystyrene cup.
Dengan cepat dan berhati-hati, tambahkan setengah spatula serbuk zink ke dalam cawan
polistirena
4. Cover the polystyrene cup with lid and stir the mixture using thermometer.
Tutupkan cawan polistirena dengan penutup dan kacaukan campuran menggunakan
termometer.
5. Record the highest temperature of the mixture, T2.
Rekodkan suhu tertinggi campuran, T2.
Tabulation of data:
Penjadualan data:
Calculation/ pengiraan :
Zn + CuSO4 ZnSO4 + Cu
Set I Set II
Change of oxidation +2 to +3 -1 to 0
number +2 kepada +3 -1 kepada 0
Perubahan nombor
pengoksidaan
34
(b) Chemicals: Potassium iodide solution (reducing agent) and bromine water (oxidising agent)
Bahan kimia: Larutan kalium iodida (agen penurunan) dan air bromin (agen pengoksidaan)
35
Prosedur: / Procedure:
Observations:
Pemerhatian:
Negative terminal:
Terminal negatif:
Colourless solution turns brown.
Larutan tak berwarna bertukar perang.
Positive terminal:
Terminal positif:
Brown bromine water turns colourless.
Warna perang air bromin bertukar kepada tak berwarna.
Direction of electrons flow:
Arah pengaliran elektron:
From carbon electrode immerse in potassium iodide solution to carbon electrode immerse in
bromine water through external wire.
Daripada elektrod karbon yang direndam dalam larutan kalium iodida ke elektrod yang
direndam dalam air bromin melalui wayar luar.
36
7. (a) *The smaller the size of beef, the larger the total surface area of beef exposed to heat.
Semakin kecil saiz daging, semakin besar jumlah luas permukaan terdedah kepada haba.
*More heat is absorbed and the beef will cook fasted.
Lebih banyak haba diserap dan daging akan cepat masak.
Materials: 0.2 mol dm-3 sodium thiosulphate, 1.0 mol dm-3 sulphuric acid, white paper with mark
X
Bahan: 0.2 mol dm-3 natrium tiosulfat, 1.0 mol dm-3 asid sulfurik, kertas putih bertanda X
Apparatus: Conical flask, measuring cylinder (50 cm3 and 10 cm3), stopwatch, thermometer,
Bunsen burner, tripod stand, wire gauze.
Radas: kelalang kon, silinder penyukat (50 cm3 dan 10 cm3), jam randik, termometer, penunu
Bunsen, tungku kaki tiga dan kasa dawai.
Procedure:
Prosedur:
1. Measure 50 cm3 of 0.2 mol dm-3 sodium thiosulphate solution and pour into a conical flask.
Sukat 50 cm3 larutan natrium tiosulfat 0.2 mol dm-3 dan tuangkan ke dalam kelalang kon.
2. Record the initial temperature of the solution.
Rekodkan suhu awal larutan.
3. Place the conical flask on top of white paper with mark X at the centre.
Letakkan kelalang kon di atas kertas putih bertanda X di bahagian tengahnya.
4. Measure 5 cm3 of 1.0 mol dm-3 sulphuric acid and pour quickly and carefully into the conical
flask.
37
Sukat 5 cm3 larutan asid sulfurik 1.0 mol dm-3 dan tuangkan dengan pantas dan berhati-hati ke
dalam kelalang kon.
5. Start the stopwatch immediately.
Mulakan jam randik serta-merta.
6. Swirl the conical flask.
Goncangkan kelalang kon.
7. Stop the stopwatch immediately once the mark X disappeared from sight and record the
time taken.
Hentikan jam randik serta-merta apabila tanda X hilang daripada penglihatan dan rekodkan
masa yang diambil.
8. The experiment is repeated using 50 cm3 of 0.2 mol dm-3 sodium thiosulphate solution heated
at different temperature of 35C, 40C, 45C and 50C.
Ulangi eksperimen dengan menggunakan 50 cm3 larutan natrium tiosulfat 0.2 mol dm-3 yang
dipanaskan pada suhu yang berlainan iaitu 35C, 40C, 45C dan 50C.
Tabulation of data:
Penjadualan data:
The higher the temperature of sodium thiosulphate solution, the shorter the time taken for the
X mark to disappear from sight.
Semakin tinggi suhu larutan natrium tiosulfat, semakin singkat masa yang diambil untuk tanda
X hilang daripada penglihatan.
Conclusion:
Kesimpulan:
The higher the temperature of sodium thiosulphate solution, the higher the rate of reaction.
Semakin tinggi suhu larutan natrium tiosulfat, semakin tinggi kadar tindak balas.
Observation:
Pemerhatian:
Mixture Observation
Campuran Pemerhatian
Zinc + hydrogen chloride in methylbenzene No change
Zink + hidrogen klorida dalam metilbenzena Tiada perubahan
Zinc + hydrogen chloride in water Gas bubbles released
Zink + hidrogen klorida dalam air Gelembung-gelembung gas terbebas
Explaination:
Penerangan:
Hydrogen chloride does not ionise in methylbenzene. Hydrogen ion is not present and hydrogen
chloride does not shows acidic property.
Hidrogen klorida tidak mengion dalam metilbenzena. Ion hidrogen tidak hadir dan hidrogen
klorida tidak menunjukkan sifat keasidan.
Hydrogen chloride ionises in water to form hydrogen ion. Hydrogen chloride shows acidic
property.
Hidrogen klorida mengion dalam air membentuk ion hidrogen. Hidrogen klorida menunjukkan
sifat keasidan.
(ii) Materials: 1 mol dm-3 hydrochloric acid, zinc oxide powder (zinc powder / zinc carbonate
powder), filter paper
Bahan: 1 mol dm-3 asid hidroklorik, serbuk zink oksida (serbuk zink / serbuk zink karbonat),
kertas turas
Apparatus: Beaker, glass rod, measuring cylinder, wire gauze, tripod stand, Bunsen burner, filter
funnel, retort stand, clamp, evaporating dish
Radas: Bikar, rod kaca, silinder penyukat, kasa dawai, tungku kaki tiga, penunu Bunsen, corong
turas, mangkuk penyejat, kaki retort dan pengapit.
Procedure:
Procedure:
1. Measure 100 cm3 of 1 mol dm-3 hydrochloric acid using measuring cylinder and pour into a
beaker. Heat the solution gently.
Sukat 100 cm3 larutan asid hidroklorik 1 mol dm-3 menggunakan silinder penyukat dan tuangkan
ke dalam sebuah bikar. Panaskan larutan perlahan-lahan.
2. Add zinc oxide powder little by little until in excess.
Tambahkan serbuk zink oksida sedikit demi sedikit sehingga berlebihan.
3. Stir the mixture using glass rod.
Kacaukan campuran menggunakan rod kaca.
39
H = 1376 kJ mol-1
1376 kJ heat 1 mol ethanol
1376 kJ tenaga 1 mol etanol
= 0.0305 46
= 1.403 g // 1.4 g
(b) (i)
Experiment I Experiment II
Eksperimen I Eksperimen II
Type of reaction Exothermic Endothermic
Jenis tindak balas Eksotermik Endotermik
Energy contents Total energy content of products Total energy content of products is
Kandungan tenaga is LOWER than total energy HIGHER than total energy content
content of reactants. of reactants.
Jumlah kandungan tenaga hasil Jumlah kandungan tenaga hasil
tindak balas LEBIH RENDAH tindak balas LEBIH TINGGI daripada
daripada jumlah kandungan jumlah kandungan tenaga bahan
tenaga bahan tindak balas. tindak balas.
40
(ii)
(c) Materials: 0.5 mol dm-3 calcium nitrate and 0.5 mol dm-3 sulphuric acid.
Bahan: 0.5 mol dm-3 kalsium nitrat dan 0.5 mol dm-3 asid sulfurik.
Procedure/kaedah :
1. Measure 25 cm3 of 0.5 mol dm-3 sulphuric acid solution using measuring cylinder and pour
into a polystyrene cup. Record the initial temperature of solution using termometer, T1.
Sukat 25 cm3 larutan asid sulfurik 0.5 mol dm-3 dengan menggunakan silinder penyukat dan
tuangkan ke dalam cawan polistirena. Rekodkan suhu awal larutan menggunakan terrmometer.
2. Measure 25 cm3 of 0.5 mol dm-3 calcium nitrate solution using measuring cylinder and pour
into another polystyrene cup. Record the initial temperature of solution using termometer, T2.
Sukat 25 cm3 larutan kalsium nitrat 0.5 mol dm-3 dengan menggunakan silinder penyukat dan
tuangkan ke dalam cawan polistirena yang lain. Rekodkan suhu awal larutan menggunakan
terrmometer, T2.
3. Pour sulphuric acid solution quickly and carefully into calcium nitrate solution.
Tuangkan larutan asid sulfurik dengan cepat dan berhati-hati ke dalam larutan kalsium nitrat.
4. Cover the polystyrene cup with lid and stir the mixture using thermometer.
Tutupkan cawan polistirena dengan penutup dan campuran dikacau menggunakan termometer.
5. Record the highest temperature of the mixture, T4.
Rekodkan suhu tertinggi campuran, T4.
Observation / Pemerhatian:
White precipitate is formed.
Mendakan putih terbentuk.
Chemical equation: Ca(NO3) + H2SO4 CaSO4 + 2HNO3
Persamaan kimia:
Results: / Keputusan:
Initial temperature of H2SO4 solution (oC) T1
Suhu awal larutan H2SO4 (oC)
Initial temperature of Ca(NO3)2 solution (oC) T2
Suhu awal larutan Ca(NO3)2 (oC)
Average temperature of the solution (C) T1 + T 2 = T3
Suhu purata larutan (C) 2
Highest temperature of the mixture (oC) T4
Suhu tertinggi campuran (oC)
Change in temperature (oC) T4 T3
Perubahan suhu (oC)
41
CALCULATION: / PENGHITUNGAN:
(iii) Material: 0.5 mol dm-3 nitric acid, 1.0 mol dm-3 nitric acid, magnesium powder (metal Q) and
water
Bahan: 0.5 mol dm-3 asid nitrik , 1.0 mol dm-3 asid nitrik, serbuk magnesium (logam Q) dan air
Apparatus: Burette, basin, conical flask, measuring cylinder, stopper with delivery tube,
electronic balance, stopwatch, retort stand and clamp.
Radas: Buret, basin, kelalang kon, silinder penyukat, penyumbat bersama salur penghantar,
penimbang elektronik, jam randik, kaki retort dan pengapit.
42
Procedure:
Prosedur:
(b)(i) Bottle Z
Botol Z
Because the concentration of acid from the lemonade is the highest // concentration of
hydrogen ions from the lemonade is the highest // lemonade contains acid.
Kerana kepekatan asid daripada jus lemon adalah paling tinggi // kepekatan ion hidrogen
daripada jus lemon adalah paling tinggi // jus lemon mengandungi asid.
43
(ii) 1. Diabetes
Penyakit diabetes
2. Tooth decay
Kerosakan gigi // Gigi mereput
3. Stomach ulcer
Ulser dalam perut
Persamaan setengah:
(b)
Cell M Cell N
Sel M Sel N
Type of cell Electrolytic cell Voltaic cell / Chemical cell
Jenis sel Sel elektrolisis Sel voltan / Sel kimia
Ions present in solution Cu , SO4 , H , OH
2+ 2- +
Cu2+, SO42-, H+, OH
Ion-ion yang hadir dalam
karutan
At anode / negative terminal Copper anode is
active Magnesium is more
Di anod / terminal negatif electrode. electropositive than copper.
Anod kuprum adalah elektrod Magnesium becomes negative
aktif. terminal. Magnesium release
electron and ionises to form
Copper release electron and magnesium ion, Mg2+.
ionises to form copper(II) Magnesium lebih
ions, Cu2+. elektropositif daripada
Kuprum mendermakan kuprum. Magnesium menjadi
elektron dan mengion terminal negatif. Magnesium
membentuk ion kuprum(II), mendermakan elektron dan
Cu2+ mengion membentuk ion
magnesium, Mg2+.
Half equation at anode / Cu Cu2+ + 2e Mg Mg2+ + 2e
negative terminal
Persamaan setengah di anod
/ terminal negatif
At cathode / positive terminal Ions attracted to cathode: Ions attracted to positive
Di katod / terminal positif Ion tertarik ke katod: terminal (cathode):
Cu2+ and H+ Ion tertarik ke terminal positif
Cu dan H
2+ +
(katod):
Mg2+, Cu2+ and H+
Cu2+ ion is selectively Mg2+ , Cu2+ dan H+
discharged at cathode
because its position is lower Cu2+ ion is selectively
than H+ ion in electrochemical discharged at positive
series. Cu2+ ion accept terminal because its position
electron to form copper atom. is lower than Mg2+ ion and H+
44
(c) Materials: Iron key, copper plate, 0.5 mol dm-3 copper(II) sulphate solution, sand paper
Bahan: Kunci besi, plat kuprum, 0.5 mol dm-3 copper(II) sulphate solution, kertas pasir
Procedure:
Prosedur:
1. Clean the iron key using sand paper.
Bersihkan kunci besi menggunakan kertas pasir.
2. Pour 150 cm3 of 0.5 mol dm-3 copper(II) solution into a beaker.
Tuangkan 150 cm3 0.5 mol dm-3 larutan kuprum(II) sulfat ke dalam sebuah bikar.
3. Immerse the iron key and copper plate into the solution.
Rendamkan kunci besi dan plat kuprum ke dalam larutan.
4. Connect copper plate to positive terminal and iron key to negative terminal of dry cells using
connecting wire.
Sambungkan plat kuprum kepada terminal positif dan kunci besi kepada terminal negatif sel
kering menggunakan wayar penyambung.
5. Turn on the switch and allow current flow for 30 minutes.
Hidupkan suis dan biarkan arus mengalir selama 30 minit.
6. Rotate the iron key slowly during electroplating.
Putarkan kunci besi perlahan-lahan semasa penyaduran.
7. Record the observation.
Rekodkan pemerhatian.
45
Observation:
Pemerhatian:
Electrode Observation
Elektrod Pemerhatian
Anode (copper plate) Copper becomes thinner.
Anod (plat kuprum) Kuprum semakin menipis.
Cathode (iron key) Brown solid deposited on iron key.
Katod (kunci besi) Pepejal perang terenap pada kunci besi.
Half equation:
Persamaan setengah:
(ii) Experiment I:
Eksperimen I:
Average rate of reaction = volume = 30 = 3.0 cm3 s-1
time 10
Experiment II:
Eksperimen II:
Average rate of reaction = volume = 30 = 1.5 cm3 s-1
time 20
Material: 0.5 mol dm-3 hydrochloric acid, zinc granule, zinc powder, water
Bahan: 0.5 mol dm-3 asid hidroklorik, ketulan zink, serbuk zink, air
Apparatus: Burette, basin, conical flask, measuring cylinder, stopper with delivery tube,
electronic balance, stopwatch, retort stand and clamp.
Radas: Buret, basin, kelalang kon, silinder penyukat, penyumbat bersama salur penghantar,
penimbang elektronik, jam randik, kaki retort dan pengapit.
Procedure:
Prosedur:
1. Fill a basin with water until half full.
Isikan sebuah besen dengan air sehingga separuh penuh.
2. Fill a burette with water until full and invert it into the basin filled with water.
Masukkan air ke dalam buret sehingga penuh dan telangkupkannya ke dalam besen berisi air.
3. Clamp the burette vertically to a retort stand. Adjust and record the initial burette reading.
Apitkan buret secara menegak kepada kaki retort. Laraskan dan rekodkan bacaan awal buret.
4. Measure 50 cm3 of 0.5 mol dm-3 hydrochloric acid and pour into a conical flask.
Sukat 50 cm3 asid hidroklorik 0.5 mol dm-3 dan tuangkan ke dalam sebuah kelalang kon.
5. Weigh 2 g of zinc granule and place it into the conical flask containing hydrochloric acid.
Timbangkan 2 g ketulan zink dan masukkan ke dalam kelalang kon berisi asid hidroklorik.
6. Close the conical flask immediately with stopper fitted with delivery tube and connect the rubber
tube into the burette.
Tutupkan kelalang kon serta-merta menggunakan penyumbat bersama salur penghantar dan
sambungkan salur penghantar ke dalam buret.
7. Start the stopwatch immediately.
Mulakan jam randek serta-merta.
8. Shake/swirl the conical flask continuously.
Goncangkan kelalang kon secara berterusan.
9. Record the burette reading at 30 seconds intervals.
Rekodkan bacaan buret setiap sela masa 30 saat.
10. Repeat steps 1 to 9 by using zinc powder to replace zinc granule.
Ulangi langkah 1 hingga 9 menggunakan serbuk zink bagi menggantikan ketulan zink.
47
Conclusion :
Kesimpulan:
Rate of reaction using zinc powder is higher. // Rate of reaction in experiment II is higher than
experiment I.
Kadar tindak balas menggunakan serbuk zink lebih tinggi // Kadar tindak balas dalam
eksperimen II lebih tinggi daripada eksperimen I.
Factor: Temperature
Faktor: Suhu
Materials: 0.2 mol dm-3 sodium thiosulphate, 1.0 mol dm-3 sulphuric acid, white paper with mark
X
Bahan: 0.2 mol dm-3 natrium tiosulfat, 1.0 mol dm-3 asid sulfurik, kertas putih bertanda X
Apparatus: Conical flask, measuring cylinder (50 cm3 and 10 cm3), stopwatch, thermometer,
Bunsen burner, tripod stand, wire gauze.
Radas: kelalang kon, silinder penyukat (50 cm3 dan 10 cm3), jam randik, termometer, penunu
Bunsen, tungku kaki tiga dan kasa dawai.
48
Procedure:
Prosedur:
1. Measure 50 cm3 of 0.2 mol dm-3 sodium thiosulphate solution and pour into a conical flask.
Sukat 50 cm3 larutan natrium tiosulfat 0.2 mol dm-3 dan tuangkan ke dalam kelalang kon.
2. Record the initial temperature of the solution.
Rekodkan suhu awal larutan.
3. Place the conical flask on top of white paper with mark X at the centre.
Letakkan kelalang kon di atas kertas putih bertanda X di bahagian tengahnya.
4. Measure 5 cm3 of 1.0 mol dm-3 sulphuric acid and pour quickly and carefully into the conical
flask.
Sukat 5 cm3 larutan asid sulfurik 1.0 mol dm-3 dan tuangkan dengan pantas dan berhati-hati ke
dalam kelalang kon.
5. Start the stopwatch immediately.
Mulakan jam randik serta-merta.
6. Swirl the conical flask.
Goncangkan kelalang kon.
7. Stop the stopwatch immediately once the mark X disappeared from sight and record the
time taken.
Hentikan jam randik serta-merta apabila tanda X hilang daripada penglihatan dan rekodkan
masa yang diambil.
8. The experiment is repeated using 50 cm3 of 0.2 mol dm-3 sodium thiosulphate solution heated
at different temperature of 35C, 40C, 45C and 50C.
Ulangi eksperimen dengan menggunakan 50 cm3 larutan natrium tiosulfat 0.2 mol dm-3 yang
dipanaskan pada suhu yang berlainan iaitu 35C, 40C, 45C dan 50C.
Tabulation of data:
Penjadualan data:
The higher the temperature of sodium thiosulphate solution, the shorter the time taken for the
X mark to disappear from sight.
Semakin tinggi suhu larutan natrium tiosulfat, semakin singkat masa yang diambil untuk tanda
X hilang daripada penglihatan.
Conclusion:
Kesimpulan:
The higher the temperature of sodium thiosulphate solution, the higher the rate of reaction.
Semakin tinggi suhu larutan natrium tiosulfat, semakin tinggi kadar tindak balas.
Apparatus: Crucible, lid, pipe clay triangle, tripod stand, Bunsen burner, tongs, electronic
balance.
Radas: mangkuk pijar, penutup, segi tiga tanah liat, tungku kaki tiga, penunu Bunsen, penyepit
kayu, penimbang elektronik
50
Procedure :
Prosedur:
1. Weigh an empty crucible and its lid and record its mass, m1.
Timbangkan mangkuk pijar kosong bersama penutup dan rekodkan jisimnya, m1.
2. Clean 10 cm of magnesium ribbon / metal Y by using sand paper.
Bersihkan 10 cm pita magnesium / logam Y menggunakan kertas pasir.
3. Coil the magnesium ribbon and place into the crucible.
Gulungkan pita magnesium dan letakkan di dalam mangkuk pijar.
4. Weigh the crucible with lid and its content again and record its mass, m2.
Timbangkan mangkuk pijar bersama penutup serta kandungannya dan rekodkan jisimnya, m2.
5. Heat the crucible strongly without its lid.
Panaskan mangkuk pijar dengan kuat tanpa penutupnya.
6. When magnesium / metal Y starts to burn, close immediately with its lid.
Apabila magnesium / logam Y mula terbakar, tutupkan mangkuk pijar dengan cepat.
7. Using a pair of tongs, the lid is lifted at intervals.
Menggunakan penyepit kayu, angkatkan sedikit penutup pada sela masa yang pendek.
7. When the burning has completed, the lid is removed and the crucible is heated strongly for 2
minutes.
Apabila pembakaran telah lengkap, penutup dialihkan dan mangkuk pijar dipanaskan dengan
kuat selama 2 minit.
8. The crucible is allowed to cool to room temperature, weighed again and its mass is
recorded, m3.
Mangkuk pijar disejukkan ke suhu bilik, ditimbang semula dan jisimnya direkodkan, m3.
9. The heating, cooling and weighing process are repeated until a constant mass is obtained.
Proses pemanasan, penyejukan dan penimbangan diulangi sehingga mendapat jisim yang tetap.
Result :
Keputusan:
Calculation:
Penghitungan:
Mg O
Mass (g) m2 m1 = p m3 m2 = q
Jisim
Number of mol P = r q = s
Bilangan mol 24 16
Simplest ratio a b
Nisbah teringkas
14. (a)(i) Number of mole of butanol = mass = jisim = 3.7 = 0.05 mol
Bilangan mol butanol molar mass jisim molar 74
H = - 2520 kJ mol-1
(ii) Some heat is lost to the surrounding//heat is absorbed by the apparatus/ tripod stand/
windshield/copper can.
Sebahagian haba telah hilang ke persekitaran // haba telah diserap oleh radas /tungku kaki
tiga/penghadang angin / bekas kuprum.
Butanol undergoes incomplete combustion // does not undergo complete combustion.
Butanol mengalami pembakaran tidak lengkap // tidak mengalami pembakaran lengkap.
(iii)
Propanol Butanol
Procedure/kaedah :
1. Measure 25 cm3 of 0.2 mol dm-3 copper (II) sulphate solution using measuring cylinder and
pour into a polystyrene cup.
Sukat 25 cm3 larutan kuprum (II) sulfat 0.2 mol dm-3 menggunakan silinder penyukat dan
tuangkan ke dalam cawan polistirena.
2. Place the thermometer into the polystyrene cup and record the initial temperature of the
solution, T1
Letakkan thermometer ke dalam cawan polistirena dan rekodkan suhu awal larutan, T1
3. Add 1 g of zinc powder quickly and carefully into the polystyrene cup.
Dengan cepat dan berhati-hati, tambahkan setengah spatula serbuk zink ke dalam cawan
polistirena
4. Cover the polystyrene cup with lid and stir the mixture using thermometer.
Tutupkan cawan polistirena dengan penutup dan kacaukan campuran menggunakan
termometer.
5. Record the highest temperature of the mixture, T2.
Rekodkan suhu tertinggi campuran, T2.
Tabulation of data:
Penjadualan data:
Calculation/ pengiraan :
Zn + CuSO4 ZnSO4 + Cu