Professional Documents
Culture Documents
D2004-5TR14 Model Centurion Series 1970 - 1976 Serv. Man.) REVISION 14
D2004-5TR14 Model Centurion Series 1970 - 1976 Serv. Man.) REVISION 14
This Temporary Revision consists of the following pages, which revise and add to existing pages in the paper
copy manual.
SECTION
2B
AIRWORTHINESS
LIMITATIONS
THE AIRWORTHINESS LIMITATIONS SECTION IS FAA APPROVED AND GIVES INSPECTIONS AND
MAINTENANCE THAT ARE REQUIRED BY PARTS 43.16 AND 91.403 OF TITLE 14 OF THE CODE OF
FEDERAL REGULATIONS, UNLESS AN ALTERNATIVE PROGRAM HAS BEEN FAA APPROVED.
10 FEBRUARY 2014
CESSNA AIRCRAFT COMPANY
MODEL 210 SERIES (1970 1976)
SERVICE MANUAL
2B Title
2B List of Effective Pages Page 1 Feb 10/2014
2B Table of Contents Page 1 Feb 10/2014
2B List of Revisions Page 1 Feb 10/2014
2B-00-00 Page 1 Feb 10/2014
2B-10-00 Page 1 Feb 10/2014
2B-11-00 Page 1 Feb 10/2014
CONTENTS
2B - CONTENTS Page 1 of 1
Cessna Aircraft Company Feb 10/2014
CESSNA AIRCRAFT COMPANY
MODEL 210 SERIES (1970 1976)
SERVICE MANUAL
LIST OF REVISIONS
1. Revisions
A. FAA Approved Airworthiness Limitations are incorporated in this manual as Section 2B. Revisions to
Section 2B are dated as approved by the FAA Regional Manager, Aircraft Certification Office. To make
sure that the maintenance information required under Title 14 of the Code of Federal Regulations, Parts
43.16 and 91.409 is current, the revisions listed in Table 1 must be incorporated in Section 2B as they are
issued.
AIRWORTHINESS LIMITATIONS
1. Scope
A. This section gives the mandatory replacement times and inspection intervals for components and airplane
structures. This section also gives the required details to monitor them using scheduled inspections.
This section applies to items such as fatigue components and structures, which are a part of the
certification procedures.
NOTE: The Airworthiness Limitations section is FAA-Approved and gives specified inspection and
maintenance necessary under Parts 43.16 and 91.409 of Title 14 of the Code of Federal
Regulations, unless an alternative program has been approved by the FAA.
2. Definition
2B-00-00 Page 1
Cessna Aircraft Company Feb 10/2014
CESSNA AIRCRAFT COMPANY
MODEL 210 SERIES (1970 1976)
SERVICE MANUAL
1. General
A. The inspection time intervals that apply to the systems and components that follow represent the
maximum inspection intervals. Detailed inspection and maintenance check procedures are described in
the associated documents elsewhere in this manual.
NOTE: An initial inspection and subsequent recurring structural inspections of these items are necessary
to maintain the airworthiness of the airplane. The recurring inspection intervals do not begin until
after the completion of the initial inspection.
2. Inspection Schedule
A. Wings (Section 4)
(1) Main Spar Lower Cap
Part Numbers 1221005-3 and -4
For airplanes operating in a typical environment, do the inspection at 8,000 hours and every
2,000 hours thereafter.
Refer to Section 2A-14-23, Supplemental Inspection Number 57-11-03.
(2) Main Spar Lower Cap
Part Numbers 1221005-3 and -4
For airplanes operating in a severe environment, do the inspection at 3,500 hours and every 500
hours thereafter.
Refer to Section 2A-14-23, Supplemental Inspection Number 57-11-03.
2B-10-00 Page 1
Cessna Aircraft Company Feb 10/2014
CESSNA AIRCRAFT COMPANY
MODEL 210 SERIES (1970 1976)
SERVICE MANUAL
1. General
A. You must replace the life-limited components that follow at the specified time. It is recommended that
you schedule the components for replacement during the airplane's inspection interval that aligns with or
occurs just before the specified time limit expires. Procedures to replace the components are given in the
applicable sections in this service manual.
2. Replacement Schedule
A. There are currently no scheduled replacement time limits associated with this airplane.
2B-11-00 Page 1
Cessna Aircraft Company Feb 10/2014