Professional Documents
Culture Documents
WMSD 723b Eu - 7107
WMSD 723b Eu - 7107
WASHING MACHINE
Contents GB
Installation, 2-3
GB PL UA Unpacking and levelling
Connecting the electricity and water supplies
English,1 Polski,13 ,25 The first wash cycle
Technical data
Troubleshooting, 11
Service, 12
1
Installation
! This instruction manual should be kept in a safe place for Levelling the machine correctly will provide it with stability,
GB future reference. If the washing machine is sold, transferred help to avoid vibrations and excessive noise and prevent it
or moved, make sure that the instruction manual remains from shifting while it is operating. If it is placed on carpet or
with the machine so that the new owner is able to familiari- a rug, adjust the feet in such a way as to allow a sufficient
se himself/herself with its operation and features. ventilation space underneath the washing machine.
! Read these instructions carefully: they contain vital infor- Connecting the electricity and water
mation relating to the safe installation and operation of the supplies
appliance.
Connecting the water inlet hose
Unpacking and levelling
1. Connect the supply pipe
Unpacking by screwing it to a cold
water tap using a gas
1. Remove the washing machine from its packaging. threaded connection (see
2. Make sure that the washing machine has not been figure).
damaged during the transportation process. If it has been Before performing the con-
damaged, contact the retailer and do not proceed any nection, allow the water to
further with the installation process. run freely until it is perfectly
clear.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber 2. Connect the inlet hose
washer with the correspon- to the washing machine by
ding spacer, located on the screwing it onto the corre-
rear part of the appliance sponding water inlet of the
(see figure). appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
1. Install the washing machine on a flat sturdy floor, without ! Never use second-hand hoses.
resting it up against walls, furniture cabinets or anything
else. ! Use the ones supplied with the machine.
2
Connecting the drain hose ! Do not use extension cords or multiple sockets.
GB
Connect the drain hose, ! The cable should not be bent or compressed.
without bending it, to a drai-
nage duct or a wall drain ! The power supply cable must only be replaced by autho-
located at a height between rised technicians.
65 and 100 cm from the
65 - 100 cm floor; Warning! The company shall not be held responsible in the
event that these regulations are not respected.
the socket is able to withstand the maximum power load maximum pressure 1 MPa (10 bar)
of the appliance as indicated on the Technical Data Plate Water connections minimum pressure 0.05 MPa (0.5 bar)
fixed on the machine; drum capacity 48 litres
the power supply voltage falls within the values indicated Spin speed up to 1200 rotations per minute
on the Technical Data Plate fixed on the machine;
Test wash cycles
in accordance programme ;
the socket is compatible with the plug of the washing
with directives temperature 60C (2nd press of the button);
machine. If this is not the case, replace the socket or the
1061/2010 and temperature 40C (3rd press of the button).
plug.
1015/2010
3
Description of the washing machine
DISPLAY
START/PAUSE
WASH MY button with
CYCLE CYCLE FUNCTION indicator light
Detergent dispenser drawer SELECTOR button buttons
buttons
DELAY TEMPERATURE
TIMER button
ANTI button
ALLERGY
RINSE CHILD LOCK
button button
Detergent dispenser drawer: used to dispense deter- TEMPERATURE button : press to decrease the tem-
gents and washing additives (see Detergents and laundry). perature: the value will be shown on the display.
ON/OFF button : press this briefly to switch the ma- CHILD LOCK button : to activate the control panel
chine on or off. The START/PAUSE indicator light, which lock, press and hold the button for approximately 2
flashes slowly in a green colour shows that the machine is seconds. When the symbol is illuminated, the control
switched on. To switch off the washing machine during the panel is locked. This means it is possible to prevent wash
wash cycle, press and hold the button for approximately 3 cycles from being modified accidentally, especially where
seconds; if the button is pressed briefly or accidentally the there are children in the home. To deactivate the control
machine will not switch off. If the machine is switched off panel lock, press and hold the button for approximately 2
during a wash cycle, this wash cycle will be cancelled. seconds.
WASH CYCLE SELECTOR buttons: used to set the DELAY TIMER button : press to set a delayed start
desired wash cycle (see Table of wash cycles). time for the selected wash cycle. The delay time will be
shown on the display.
MY CYCLE button: press and hold the button to store a
cycle with your own set of preferences in the memory of START/PAUSE button with indicator light: when the gre-
the machine. To recall a previously stored cycle, press the en indicator light flashes slowly, press the button to start a
MY CYCLE button. wash cycle. Once the cycle has started the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
FUNCTION buttons: press the button to select the press the button again; the indicator light will flash in an
desired function. The corresponding indicator light on the orange colour. If the symbol is not illuminated, the door
display will switch on. may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
CLEANING ACTION button : to select the desired
wash intensity. Standby mode
This washing machine, in compliance with new energy sa-
ANTI ALLERGY RINSE button : press to select ving regulations, is fitted with an automatic standby system
the desired rinse type. which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
SPIN button : press to reduce or completely exclude machine to start up again.
the spin cycle - the value is indicated on the display. Consumption in off-mode: 1 W
Consumption in Left-on: 1 W
4
Display
GB
A X
Z B
D
C
E
The display is useful when programming the machine and provides a great deal of information.
The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-
tion relating to the progress status of the wash cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the
time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include
a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-
rature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.
! The first time the machine is switched on, you will be asked to select the language and the display will automatically show
the language selection menu.
To select the desired language press the X and Y buttons; to confirm the selection press the Z button.
To change the language switch off the machine and press buttons X, Y, Z simultaneously until an alarm is heard: the
language-selection menu will be displayed again.
5
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the On/Off The cycle will reduce the drum rotation to ensure
GB button ; the text POWER ON will appear on the washing results are perfect for delicate garments. If the
display and the START/PAUSE indicator light will flash current selection can be neither set nor changed, the
slowly in a green colour. display will show Not allowed.
2. LOAD THE LAUNDRY. Open the porthole door. Set the rinse type.
Load the laundry, making sure you do not exceed Option makes it possible to select the desired rinse
the maximum load value indicated in the table of type for sensitive skin. Press the button once for the
programmes on the following page. Extra Rinse level, which makes it possible to select
3. MEASURE OUT THE DETERGENT. Open the an additional rinse after the standard cycle rinse and
detergent dispenser drawer and pour the detergent into remove all traces of detergent. Press the button again
for the Sensitive Skin level, which makes it possible to
the relevant compartments as described in Detergents
select two additional rinses to the standard cycle rinses; it
and laundry.
is recommended for very sensitive skin. Press the button
4. CLOSE THE DOOR. for the third time for the Anti allergy Rinse level, which
5. SELECT THE WASH CYCLE. Press one of the WASH makes it possible to select three additional rinses to the
CYCLE SELECTOR buttons to select the required wash standard cycle rinses and remove major allergens such as
cycle; the name of the wash cycle will appear on the pollen, mites, cat and dog hair. Press the button again to
display. A temperature and spin speed is set for each go back to the Normal Rinse rinse type. If the current
wash cycle; these may be adjusted. The duration of the adjustment can be neither set nor changed, the display will
cycle will appear on the display. show Not allowed.
6. CUSTOMISE THE WASH CYCLE. Use the relevant Modifying the cycle settings.
buttons: Press the button to enable the function; the indicator
Modifying the temperature and/or spin light corresponding to the button will switch on.
speed. The machine automatically selects the Press the button again to disable the function; the
maximum temperature and spin speed set for the indicator light will switch off.
selected wash cycle; these values cannot therefore ! If the selected function is not compatible with the
be increased. The temperature can be decreased by programmed wash cycle, the indicator light will flash
pressing the button, until the cold wash OFF and the function will not be activated.
setting is reached. The spin speed may be progressively ! If the selected function is not compatible with
reduced by pressing the button, until it is completely another function which has been selected previously,
excluded (the OFF setting). If these buttons are the indicator light corresponding to the first function
pressed again, the maximum values are restored. selected will flash and only the second function will
Setting a delayed start. be activated; the indicator light corresponding to the
To set a delayed start for the selected programme, enabled function will remain lit.
press the corresponding button repeatedly until the ! The functions may affect the recommended load value
required delay period has been reached. When this and/or the duration of the cycle.
option is enabled, the symbol lights up on the 7. START THE PROGRAMME. Press the START/PAUSE
display. To remove the delayed start function press the button. The corresponding indicator light will become
button until the text OFF appears on the display. green, remaining lit in a fixed manner, and the door will be
Set the desired wash intensity. locked (the DOOR LOCKED symbol will be on). During
Option makes it possible to optimise washing the wash cycle, the name of the phase in progress will
based on the level of soil in the fabrics and on desired appear on the display. To change a wash cycle while
wash cycle intensity. it is in progress, pause the washing machine using the
Select the wash programme: the cycle will be START/PAUSE button (the START/PAUSE indicator light
automatically set to Normal as optimised for garments will flash slowly in an orange colour); then select the
with an average level of soil (this setting is not applicable to desired cycle and press the START/PAUSE button again.
the Wool cycle, which is automatically set to Delicate). To open the door while a cycle is in progress, press
For heavily-soiled garments press button until the START/PAUSE button; if the DOOR LOCKED
the Super Wash level is reached. This level ensures symbol is switched off the door may be opened. Press
a high-performance wash due to a larger quantity of
the START/PAUSE button again to restart the wash cycle
water used in the initial phase of the cycle and due to
from the point at which it was interrupted.
increased drum rotation. It is useful when removing the
most stubborn stains. 8. THE END OF THE WASH CYCLE. This will be
It can be used with or without bleach. If you wish to indicated by the text END OF CYCLE on the display;
bleach the items insert the additional compartment when the DOOR LOCKED symbol switches off
(4) into compartment 1. When pouring the bleach, be the door may be opened. Open the door, unload the
careful not to exceed the max level marked on the
laundry and switch off the machine.
central pivot (see figure pag. 8).
For lightly-soiled garments or a more delicate treatment ! If you wish to cancel a cycle which has already begun,
of the fabrics, press button until the Delicate level press and hold the button. The cycle will be stopped
is reached. and the machine will switch off.
6
Wash cycles and functions
Cycle duration
Residual dam-
sumption kWh
Total water lt
Wash cycles
Energy con-
Detergents
Max. load
pness %
Max. Max.
(kg)
Description of the wash cycle temp. speed
(C) (rpm) Pre- Wash Bleach Fabric
Wash softener
Wash functions
Timer Saver Eco Wash
If you select this option, the wash cycle duration will be redu- The Eco Wash function saves energy by not heating the
ced by up to 50%, depending on the selected cycle, thereby water used to wash your laundry an advantage both to
guaranteeing simultaneous water and energy saving. Use this the environment and to your energy bill. Instead, intensified
cycle for lightly soiled garments. wash action and water optimisation ensure great wash
! It cannot be used with the , Fastwash 60, , , . results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
Easy Iron a liquid detergent.
By selecting this function, the wash and spin cycles will be ! It cannot be used with the , (90C), , , , .
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine will perform
slow rotations of the drum; the Easy Iron and START/
PAUSE indicator lights will flash (orange) and the text END
OF CYCLE will appear on the display. To end the cycle,
press the START/PAUSE button or the Easy Iron button.
! It cannot be used with the , Fastwash 30, , ,
Fast spin Resistents and Pump out.
7
Detergents and laundry
8
Precautions and tips
! This washing machine was designed and constructed in Opening the porthole door manually
accordance with international safety regulations. The fol- GB
In the event that it is not possible to open the porthole
lowing information is provided for safety reasons and must
door due to a powercut, and if you wish to remove the
therefore be read carefully.
laundry, proceed as follows:
General safety
1. remove the plug from the
This appliance was designed for domestic use only. electrical socket.
This appliance is not intended for use by persons (inclu- 2. make sure the water level
ding children) with reduced physical, sensory or mental inside the machine is lower
capabilities, or lack of experience and knowledge, unless 20
than the door opening; if it
they have been given supervision or instruction concer- is not, remove excess water
ning use of the appliance by a person responsible for using the drain hose, collec-
their safety. Children should be supervised to ensure that ting it in a bucket as indicated
they do not play with the appliance. in the figure.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
3. using a screwdriver, remo-
Do not pull on the power supply cable when unplugging ve the cover panel on the lo-
the appliance from the electricity socket. Hold the plug wer front part of the washing
and pull. machine (see figure).
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extreme-
ly high temperatures.
Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
4. pull outwards using the tab as indicated in the figure,
sure the drum is empty.
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
Disposal
Disposing of the packaging materials: observe local regu- 5. reposition the panel, making sure the hooks are securely
lations so that the packaging may be re-used. in place before you push it onto the appliance.
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the im-
pact on human health and the environment. The crossed
out wheeled bin symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected. Consumers should contact
their local authority or retailer for information concerning the
correct disposal of their old appliance.
9
Care and maintenance
Cutting off the water and electricity Caring for the door and drum of your
GB supplies appliance
Turn off the water tap after every wash cycle. This will limit Always leave the porthole door ajar in order to prevent
wear on the hydraulic system inside the washing machine unpleasant odours from forming.
and help to prevent leaks.
Cleaning the pump
Unplug the washing machine when cleaning it and du-
ring all maintenance work. The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
Cleaning the washing machine items (such as coins or buttons) may fall into the pre-cham-
ber which protects the pump, situated in its bottom part.
The outer parts and rubber components of the applian-
ce can be cleaned using a soft cloth soaked in lukewarm ! Make sure the wash cycle has finished and unplug the
soapy water. Do not use solvents or abrasives. appliance.
The washing machine has a Auto Clean programme
for its internal parts that must be run with no load in the To access the pre-chamber:
drum.
For maximum performance you may want to use either 1. using a screwdriver,
the detergent (i.e. a quantity 10% the quantity specified remove the cover panel
for lightly-soiled garments) or special additives to clean on the lower front part of
the washing machine. We recommend running a cleaning the washing machine (see
programme every 40 wash cycles. figure);
To start the programme press buttons A and B simulta-
neously for 5 seconds (see figure).
The programme will start automatically and will last appro-
ximately 70 minutes. To stop the cycle press the START/
PAUSE button.
A B
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
Check the inlet hose at least once a year. If there are any
2
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
10
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make sure
that the problem cannot be not solved easily using the following list. GB
The washing machine does not The appliance is not plugged into the socket fully, or is not making contact.
switch on. There is no power in the house.
The wash cycle does not start. The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see Running a wash cycle).
The washing machine does not The water inlet hose is not connected to the tap.
take in water (the text NO WATER, The hose is bent.
CHECK SUPPLY appears on the The water tap has not been opened.
display). There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine continuously The drain hose is not fitted at a height between 65 and 100 cm from the floor
takes in and (see Installation).
drains water. The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The washing machine does not The wash cycle does not include draining: some wash cycles require the drain
drain or spin. phase to be started manually (see Wash cycles and functions).
The EASY IRON function has been activated: To complete the wash cycle,
press the START/PAUSE button (see Wash cycles and functions).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The washing machine vibrates a lot The drum was not unlocked correctly during installation (see Installation).
during the spin cycle. The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The washing machine leaks. The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and maintenance).
The drain hose is not fixed properly (see Installation).
The machine is locked and the display Switch off the machine and unplug it, wait for approximately 1 minute and then
flashes, indicating an switch it back on again.
error code (e.g. F-01, F-..). If the problem persists, contact the Technical Assistance Service.
There is too much foam. The detergent is not suitable for machine washing (it should display the text
for washing machines or hand and machine wash, or the like).
Too much detergent was used.
11
Service
12
Instrukcja obsugi
PRALKA
Spis treci PL
Instalacja, 14-15
PL Rozpakowanie i wypoziomowanie
Podczenia hydrauliczne i elektryczne
Polski Pierwszy cykl prania
Dane techniczne
Programy i funkcje, 19
Tabela programw
Funkcje prania
Utrzymanie i konserwacja, 22
Odczenie wody i prdu elektrycznego
Czyszczenie pralki
Czyszczenie szufladki na rodki piorce
Konserwacja okrgych drzwiczek i bbna
Czyszczenie pompy
Kontrola przewodu doprowadzajcego wod
Serwis Techniczny, 24
13
Instalacja
! Naley zachowa niniejsz ksieczk, aby mc z niej Staranne wypoziomowanie pralki zapewnia jej stabilno
PL i zapobiega wibracjom, haasowi oraz przesuwaniu si
skorzysta w kadej chwili. W przypadku sprzeday,
odstpienia lub przeniesienia pralki w inne miejsce maszyny w czasie pracy. W razie ustawienia na dywa-
naley zadba o przekazanie instrukcji wraz z maszyn, nie lub wykadzinie dywanowej naley tak wyregulowa
aby nowy waciciel mg zapozna si z dziaaniem nki, aby pod pralk pozostawaa wolna przestrze
urzdzenia i z dotyczcymi go ostrzeeniami. niezbdna dla wentylacji.
14
Podczenie przewodu odpywowego ! Nie uywa przeduaczy ani rozganikw.
PL
Podczy przewd ! Przewd nie powinien by pozginany ani przygnieciony.
odpywowy, nie zginajc
go, do rury ciekowej lub ! Przewd zasilania elektrycznego moe by wymieniany
do otworu odpywowego wycznie przez autoryzowanych technikw.
w cianie, ktre powin-
65 - 100 cm ny znajdowa si na Uwaga! Producent nie ponosi adnej odpowiedzialnoci
wysokoci od 65 do 100 w przypadku nieprzestrzegania powyszych zasad.
cm od podogi;
15
Opis pralki
Wywietlacz
Przycisk z
Przycisk Przyciski kontrolk
Przyciski MY CYCLE FUNKCJI START/PAUSE
PRZECZNIKA
Szufladka na rodki piorce PROGRAMW
Przycisk Przycisk
TYP TEMPERATURY
PUKANIA
Przycisk
BLOKADA
Przycisk PRZYCISKW
URUCHOMIENIE
OPNIONE
Szufladka na rodki piorce: do dozowania rodkw Przycisk TEMPERATURY : nacisn w celu zmniejsze-
piorcych i dodatkw (patrz rodki piorce i bielizna). nia temperatury: warto zostaje wywietlona na ekranie.
Przycisk ON/OFF : nacisn krtko przycisk w celu Przycisk BLOKADA PRZYCISKW : w celu
wczenia lub wyczenia maszyny. Kontrolka START/ uruchomienia lub wylaczenia blokady panelu sterowania
PAUSE, ktra pulsuje powoli w kolorze zielonym wskazu- nalezy przytrzymac nacisniety przycisk przez okolo
je, e maszyna jest wczona. W celu wyczenia pralki 2 sekundy. Podswietlony symbol wskazuje, ze
podczas prania konieczne jest dusze przytrzymanie panel sterowania zostal zablokowany. W ten sposb
nacinitego przycisku, przez okoo 3 sek.; krtkie lub uniemozliwia sie dokonywanie przypadkowych zmian w
przypadkowe nacinicie wystarczy do wyczenia ma- programach, zwlaszcza, jesli w domu obecne sa dzieci.
szyny. Wyczenie maszyny podczas trwajcego prania W celu wylaczenia blokady panelu sterowania nalezy
anuluje program prania. przytrzymac nacisniety przycisk przez okolo 2 sekundy.
16
Wywietlacz
PL
A X
Z B
D
C
E
W obu wierszach grnych A i B wywietlane s: wybrany program prania, faza prania biecego oraz wszelkie wskaza-
nia zwizane ze stanem zaawansowania programu.
W wierszu C wywietlany jest czas pozostay do koca cyklu prania biecego oraz, jeli zaprogramowano URUCHO-
MIENIE OPNIONE, czas brakujcy do uruchomienia wybranego programu.
W wierszu D wywietlana jest maksymalna warto szybkoci wirwki, jak maszyna moe uzyska w przypadku wybra-
nego programu; jeli program nie przewiduje wirowania wiersz pozostaje wygaszony.
W wierszu E wywietlana jest maksymalna warto temperatury, jak mona wybra w przypadku wybranego programu,
jeli program nie przewiduje ustawiania temperatury, wiersz pozostaje wygaszony.
Kontrolki F zwizane s z funkcjami i wczaj si, kiedy wybrana funkcja zgodna jest z wybranym programem.
Symbol zablokowanych drzwiczek
Zapalony symbol oznacza, e okrge drzwiczki pralki s zablokowane, aby zapobiec przypadkowemu ich otworzeniu.
Aby unikn uszkodzenia pralki, naley odczeka, a symbol ten zganie, zanim przystpi si do otwierania drzwiczek
pralki.
Uwaga: jeli aktywna jest funkcja URUCHOMIENIE OPNIONE drzwiczek nie mona otworzy. W celu ich otwarcia
naley ustawi maszyn w pauzie poprzez nacinicie przycisku START/PAUSE.
! Podczas pierwszego uruchomienia wymagane bdzie dokonanie wyboru jzyka a wywietlacz ustawi si automatycznie
na menu wyboru jzyka.
W celu wybrania danego jzyka nacisn przyciski X i Y, dla potwierdzenia wyboru nacisn przycisk Z.
Aby zmieni jzyk, naley wyczy urzdzenie, nacisn rwnoczenie przyciski X, Y, Z, a do usyszenia sygnau
dwikowego, wywietli si menu wyboru jzyka.
17
W jaki sposb wykona cykl prania
1. WCZENIE MASZYNY. Nacisn przycisk , na odziey. Jeli ktre z ustawie lub zmiana ustawienia
PL wywietlaczu pojawi si napis WCZENIE, kontrolka nie jest moliwe, na wywietlaczu pojawi si napis
START/PAUSE zacznie powoli pulsowa w kolorze zielonym. ZABLOKOWANE.
2. WKADANIE BIELIZNY. Otworzy szklane drzwiczki. Ustawi rodzaj pukania.
Woy bielizn uwaajc, aby nie przekroczy wielkoci Opcja umoliwia wybranie rodzaju pukania
wsadu wskazanej w tabeli programw na nastpnej stronie. przeznaczonego do jak najwikszej ochrony delikatnej
3. DOZOWANIE RODKA PIORCEGO. Wysun skry. Po pierwszym naciniciu przycisku, zostaje
szufladk i wsypa detergent do odpowiednich komr w ustawiony poziom EXTRA PUKANIE, ktry pozwala
sposb wyjaniony w rodki piorce i bielizna. wybra dodatkowe pukanie, oprcz standardowego,
w celu usunicia wszelkich pozostaoci detergentu.
4. ZAMKN DRZWICZKI.
Po drugim naciniciu przycisku, zostaje ustawiony
5. WYBR PROGRAMU. Nacisn jeden z przyciskw poziom WRALIWA SKRA, ktry pozwala wybra
PRZECZNIKA PROGRAMW w celu wybrania dwa dodatkowe pukania, oprcz standardowego, w
potrzebnego programu, nazwa programu pojawi si na celu jak najlepszej ochrony delikatnej skry. Po trzecim
wywietlaczu; z nim powizana jest temperatura oraz naciniciu przycisku, zostaje ustawiony poziom
prdko wirowania, ktre mog zosta zmienione. Na ANTYALERGICZNE, ktry pozwala wybra trzy
wywietlaczu pojawi si czas trwania cyklu. dodatkowe pukania, oprcz standardowego, w celu
6. PERSONALIZACJA CYKLU PRANIA. usunicia gwnych alergenw, takich jak pyki, roztocza,
Przy pomocy odpowiednich przyciskw: sier psw i kotw. Nacisn ponownie przycisk, aby
Zmieni temperatur i/lub wirwk. Maszyna powrci do PUKANIE STANDARDOWE rodzaju
wybierze automatycznie temperatur oraz wirwk pukania. Jeli ktre z ustawie lub zmiana ustawienia
maksymalne przewidziane dla danego programu, dlatego nie jest moliwe, na wywietlaczu pojawi si napis
nie mog one by zwikszane. Poprzez naciskanie ZABLOKOWANE.
przycisku stopniowo zmniejsza si temperatur a do Zmiana charakterystyki cyklu.
prania w zimnej wodzie OFF. Naciskajc przycisk Naciska przycisk w celu uruchomienia funkcji;
stopniowo zmniejsza si wirwk a do jej wyczenia zawieci si kontrolka odpowiadajca przyciskowi.
OFF. Dodatkowe nacinicie przyciskw przywrci Nacisn ponownie przycisk w celu wyczenia funkcji,
maksymalne wartoci przewidywane. kontrolka zganie.
Ustawienie opnionego rozpoczcia. ! Jeli wybrana funkcja nie jest zgodna z wybranym
W celu ustawienia opnionego rozpoczcia wybranego programem, kontrolka bdzie pulsowa, a funkcja nie
programu naley naciska odpowiedni przycisk a do zostanie uruchomiona.
osignicia danego czasu opnienia. Kiedy opcja ta jest ! Jeli wybrana funkcja nie jest zgodna z inn, ustawion
aktywna, na wywietlaczu pojawia si symbol . W celu uprzednio, kontrolka odpowiadajca pierwszej funkcji
usunicia opnionego uruchomienia naley naciska bdzie pulsowaa i uruchomiona zostanie jedynie druga
przycisk a do pojawienia si napisu OFF. funkcja a kontrolka uruchomionej funkcji zawieci si.
Ustawi dany stopie intensywnoci prania. ! Funkcje mog zmienia zalecane obcienie i/lub czas
Opcja umoliwia optymalizacj prania w trwania cyklu.
zalenoci od stopnia zabrudzenia tkanin oraz danej 7. URUCHOMIENIE PROGRAMU. Nacisn przycisk
intensywnoci prania. START/PAUSE. Odpowiednia kontrolka zawieci si
Wybra program prania, cykl zostanie automatycznie kolorem zielonym i drzwiczki zostan zablokowane
ustawiony na poziomie NORMALNY, przeznaczonym (symbol ZABLOKOWANYCH DRZWICZEK wieci
dla rednio zabrudzonej odziey, (ustawienie to si). Podczas prania na wywietlaczu pojawi si nazwa
nie stosuje si dla cyklu Wena, ktry ustawia si biecej fazy. W celu zmiany programu w czasie trwania
automatycznie na poziomie DELIKATNE). cyklu naley ustawi pralk w pauzie naciskajc przycisk
W przypadku silnie zabrudzonej odziey, naley nacisn START/PAUSE (kontrolka START/PAUSE zacznie powoli
przycisk a do przejcia do poziomu SUPER pulsowa w kolorze pomaraczowym); nastpnie wybra
PRANIE. Poziom ten gwarantuje wysokiej jakoci potrzebny cykl i ponownie nacisn przycisk START/
pranie, dziki uyciu wikszej iloci wody w pocztkowej PAUSE. W celu otwarcia drzwiczek w trakcie wykonywania
fazie cyklu i intensywniejszym ruchom mechanicznym cyklu naley nacisn przycisk START/PAUSE; jeli
suy do usuwania najoporniejszych plam. Moe by symbol ZABLOKOWANYCH DRZWICZEK jest
uywany z wybielaczem i bez niego. wyczony moliwe bdzie otwarcie drzwiczek Nacisn
Jeli chce si przeprowadzi wybielanie, naley woy ponownie przycisk START/PAUSE, aby uruchomi
dodatkow szufladk 4, znajdujc si w wyposaeniu, program od punktu, w ktrym zosta przerwany.
do szufladki 1. Nie przekracza poziomu max 8. KONIEC PROGRAMU. Wskazywany jest napisem
wybielacza w pynie, podanej na rodkowym wskaniku KONIEC CYKLU na wywietlaczu, kiedy symbol
(zobacz rysunek na str. 20). ZABLOKOWANYCH DRZWICZEK wyczy si,
W przypadku lekko zabrudzonej odziey lub w celu moliwe bdzie otwarcie drzwiczek. Otworzy drzwiczki,
delikatnego obchodzenia si z tkaninami, naley wyj bielizn i wyczy maszyn.
nacisn przycisk a do przejcia do poziomu
DELIKATNE. Cykl zredukuje ruchy mechaniczne, ! Jeli zamierza si anulowa uruchomiony juz cykl,
aby zagwarantowa doskonay efekt prania delikatnej przytrzyma duej nacinity przycisk . Cykl zostanie
przerwany i maszyna wyczy si.
18
Programy i funkcje
Tabela programw
PL
Wilgotno resztkowa %
Woda cznie lt
Prd-
Programy
ko
Temp.
Opis programu max
max.
(obro- Pranie Pra- Wybie- rodek
(C)
tw na wstpne nie zmik-
lacz
minut) czajcy
Funkcje prania
Pranie szybkie
Wybierajc t opcj, skraca si czas trwania programu na- ! Nie mona go uruchomi w programach ,
wet do 50%, w zalenoci od wybranego cyklu, gwarantujc Szybkie Pranie 30, , , Wirowanie Intensywne i
rwnoczenie oszczdno wody i energii. Z cyklu naley Odprowadzamie wody.
korzysta do prania niezbyt zabrudzonej odziey. Eco wash
! Nie mona jej uruchomi w programach , Szybkie Funkcja Eco Wash umoliwia oszczdnoci pod
Pranie 60, , , . wzgldem zuywanej energii, nie podgrzewajc wody
atwe prasowanie uywanej do prania, co niesie za sob korzyci zarwno
Po wybraniu tej funkcji, pranie oraz wirwka zostan dla rodowiska naturalnego, jak i dla rachunku za prd.
odpowiednio zmienione w celu ograniczenia Wzmocniona sia dziaania i zoptymalizowane zuycie
powstawania zgniece. wody gwarantuj doskonae rezultaty przy dugoci
Po zakoczeniu cyklu pralka wykona powolne obroty cyklu takiej samej, jak w przypadku cyklu standard. Aby
bbna, kontrolka funkcji ATWE PRASOWANIE zawieci uzyska jak najlepsze rezultaty, zalecamy korzysta z
si, a kontrolka START/PAUSE bdzie pulsowaa powoli pynu do prania.
w kolorze pomaraczowym. W celu zakoczenia cyklu ! Nie mona jej uruchomi w programach , (90C),
naley nacisn przycisk START/PAUSE lub przycisk , , , .
ATWE PRASOWANIE.
19
rodki piorce i bielizna
20
Zalecenia i rodki
ostronoci
! Pralka zostaa zaprojektowana i wyprodukowana zgodnie Konsumenci powinni kontaktowa si z wadzami
z midzynarodowymi normami bezpieczestwa. Niniej- lokalnymi lub sprzedawc w celu uzyskania informacji PL
sze ostrzeenia zostay tu zamieszczone ze wzgldw dotyczcych postpowania z ich zuytymi urzdzeniami
bezpieczestwa i naley je uwanie przeczyta. gospodarstwa domowego.
Utylizacja
Utylizacja opakowania: stosowa si do lokalnych pr-
zepisw, dziki temu opakowanie bdzie mogo zosta
ponownie wykorzystane.
Europejska Dyrektywa 2002/96/EC dotyczca Zuytych
Elektrycznych i Elektronicznych Urzdze zakada zakaz 4. pocign na zewntrz klapk wskazan na rysunku,
pozbywania si starych urzdze domowego uytku a do wyzwolenia si z zacisku plastikowego zaczepu;
jako nieposortowanych mieci komunalnych. Zuyte nastpnie pocign go w d i rwnoczenie otworzy
urzdzenia musz by osobno zbierane i sortowane drzwiczki.
w celu zoptymalizowania odzyskania oraz ponownego
przetworzenia pewnych komponentw i materiaw. 5. ponownie zaoy panel upewniwszy si, przed
Pozwala to ograniczy zanieczyszczenie rodowiska i dociniciem go do maszyny, czy zatrzaski zostay umie-
pozytywnie wpywa na ludzkie zdrowie. Przekrelony szczone w odpowiednich otworach.
symbol kosza umieszczony na produkcie przypomina
klientowi o obowizku specjalnego sortowania.
21
Utrzymanie i konserwacja
22
Nieprawidowoci w dziaaniu
i sposoby ich usuwania
Moe si zdarzy, e pralka nie dziaa. Przed wezwaniem Serwisu Technicznego (patrz Serwis Techniczny) naley
sprawdzi, czy problemu nie da si atwo rozwiza przy pomocy poniszego wykazu. PL
Cykl prania nie rozpoczyna si. Drzwiczki pralki nie s dobrze zamknite.
Nie zosta wcinity przycisk ON/OFF.
Nie zosta wcinity przycisk START/PAUSE.
Kurek dopywu wody jest zamknity.
Zostao nastawione opnienie startu (patrz W jaki sposb wykona cykl
prania).
Pralka nie pobiera wody (na Przewd doprowadzajcy wod nie jest podczony do kurka.
wywietlaczu pojawi si napis BRAK Przewd jest zgity.
WODY, SPRAWD DOPYW WODY). Kurek dopywu wody jest zamknity.
W domu nastpia przerwa w dostawie wody.
Cinienie wody nie jest wystarczajce.
Nie zosta wcinity przycisk START/PAUSE.
Pralka cay czas pobiera i odprowad- Przewd odpywowy nie zosta zainstalowany na wysokoci midzy 65 a
za wod. 100 cm od podogi (patrz Instalacja).
Kocwka przewodu odpywowego jest zanurzona w wodzie (patrz Instalacja).
Otwr odpywowy w cianie nie posiada odpowietrznika.
Jeli po sprawdzeniu tych moliwoci problem nie zostanie rozwizany, naley
zamkn kurek dopywu wody, wyczy pralk i wezwa Serwis Techni-
czny. Jeli mieszkanie znajduje si na najwyszych pitrach budynku, moe
wystpi efekt syfonu, w wyniku ktrego pralka cay czas pobiera i odprowad-
za wod. W celu wyeliminowania tej niedogodnoci naley zakupi specjalny
zawr, zapobiegajcy powstawaniu efektu syfonu.
Pralka nie odprowadza wody i nie Program nie przewiduje odprowadzania wody: w przypadku niektrych pro-
odwirowuje prania. gramw naley uruchomi je rcznie (patrz Programy i funkcje).
Wczona jest funkcja ATWE PRASOWANIE: aby zakoczy program,
naley nacisn przycisk START/PAUSE (Programy i funkcje).
Przewd odpywowy jest zgity (patrz Instalacja).
Instalacja odpywowa jest zatkana.
Pralka mocno wibruje w fazie wirowania. Podczas instalacji pralki bben nie zosta prawidowo odblokowany (patrz
Instalacja).
Pralka nie jest waciwie wypoziomowana (patrz Instalacja).
Pralka, zainstalowana pomidzy meblami a cian, ma za mao miejsca
(patrz Instalacja).
Z pralki wycieka woda. Przewd doprowadzajcy wod nie jest dobrze przykrcony (patrz Instalacja).
Szufladka na rodki piorce jest zatkana (w celu jej oczyszczenia patrz Utr-
zymanie i konserwacja).
Przewd odpywowy nie jest dobrze zamocowany(patrz Instalacja).
Maszyna jest zablokowana, wywietlacz Wyczy maszyn i wyj wtyczk z gniazdka, odczeka okoo 1 minuty,
pulsuje i sygnalizuje kod anomalii (np.: nastpnie wczy j ponownie.
F-01, F-..). Jeli problem nie ustpuje, naley wezwa Serwis Techniczny.
Tworzy si zbyt dua ilo piany. rodek piorcy nie jest odpowiedni do pralek automatycznych (na opako-
waniu musi by umieszczony napis: do pralek, do prania rcznego i w
pralce lub podobny).
Uyto za duo rodka piorcego.
23
Serwis Techniczny
Naley poda:
rodzaj nieprawidowoci;
model maszyny (Mod.);
numer seryjny (S/N).
Informacje te znajduj si na tabliczce umieszczonej w tylnej czci pralki oraz widocznej z przodu po otwarciu drzwiczek.
24
Ii i
UA
UA , 26-27
ii i
, 28-29
, 30
, 31
WMSD 723 , 32
i
, 33
, 34
, 35
, 36
25
! , i ii
UA - . i i ii,
, i .
,
, ,
. .
! :
,
.
i
1.
,
1. .
2. , 3/4 (.
i . , ).
i i i
. i ,
.
3. 4
i
2.
, i ,
(. i
). ,
i
(. ).
4.
.
5. i i : i 3. , .
i i.
!
! i . (. ).
! ,
1. .
, , , .
! , i i.
2. i
i , ! .
ii
i
i (. )
;
i
i
2.
26
! .
UA
ii ! i i
, i ii.
, i
!
i , i .
65 - 100 cm ii
65 -100 i i;
i i
,
i,
(60C).
,
(.
).
.
!
. i ii
, , ii i
150 . WMSD 723
59,5
i 85
i i , 43,5
, :
ii i i 1 7
. i
; i
1 (10 )
i
, ii 0,05 (0,5 )
i
(. ); 48 i
i
1200 i
,
(. );
; 60C (
.
);
. 7 .
EN 60456
!
, i,
ii
. :
- 2004/108/CE (
! , ii)
. - 2002/96/CE
- 2006/95/CE ( )
! .
27
UA ON/OFF
I
MY CYCLE START/PAUSE
I
I
: :
i (. i i). : i
.
ON/OFF :
i . I :
START/PAUSE i i
, , 2 .
i. , .
,
3 .; , . i
. i i
ii . 2 .
: I : i
, i
(. ). . i i .
MY CYCLE: , START/PAUSE:
i .
, , , .
i MY CYCLE. ,
. ,
I: ;
i . .
ii i . i, i .
, ,
: .
.
i
: ii ,
. i,
(stand by), 30
I : ii .
i i; i ON/OFF i
i . .
28
UA
A X
Z B
D
C
E
; i ii ii.
i , , i i
.
i , , i
I .
D i i i, i
; i i, .
E i , i
; i , .
Ii F i i: , i i
.
i , , i i.
i , i i , , .
: i i I i , i
i , START/PAUSE.
! ii , i .
i X Y, i i, i Z.
, X, Y, Z
, .
29
1. . i : ,
UA WELCOME; i
START/PAUSE i .
i i. ,
2. . Not allowed ( ).
. , , .
,
. ,
3. . .
, Extra Rinse ( )
ii . ,
.
4. . Sensitive Skin ( ),
5. .
i ; ;
; .
i i Anti allergy Rinse (
i i. ),
i . ,
6. I I , , ,
. iii : . ,
/ i Normal Rinse () .
. ,
, Not allowed ( ).
, . ii .
, i i i;
i ii i .
OFF. , i i;
, OFF. .
! i ,
. ,
i i . i .
i ! ,
ii , ,
i i. i ,
, . i,
i , i.
OFF. ! i i
/ i .
.
7. . START/
PAUSE. ii i i
. i,
, (i )
Normal () , i
. i i
( i , START/
, PAUSE (i START/PAUSE
Delicate () ). i i);
i i START/
Super Wash (). PAUSE .
START/PAUSE;
,
; , .
. START/PAUSE,
. i, .
, 4 8. . END
1. i OF CYCLE ;
ii i , i.
max i (. , .
. 32). ! ii i ,
, , i
, .
, Delicate ().
30
UA
.
.
. i
. (i - -
i
() -
-
)
-
()
40 1200 - - 4
i ( ): 90 1200 - 7
i.
i (1) ( ): i 60 1200 - 7
i i .
ii ii i .
(2) ( ): i 40 1200 - 7
ii ii i .
i ( ): i 60 800 - 3
i ii .
i (4) ( ): i 40 800 - 3
i ii .
i ( ): i 40 800 - 3
i ii .
Mix 60 ( ): i
( , 60 1200 - - 3.5
).
Mix 30 ( ): i
( , 30 800 - - 3
).
M My Cycle: , i
(3): . 60 1200 - - 7
: , i, . 40 800 - - 1.5
30 0 - - 1
i ( ) - 1200 - - - - 7
( ) - 1200 - - - 7
( ) - 0 - - - - 7
, , . ,
, , , , , .
i :
1) i EN 60456: 60C ( ).
2) : 40C ( ).
3) : ; 40C ( ).
4) : 60C ( ); 40C
( ).
Eco wash
i i i Eco Wash ,
50% i ,
i.
. .
,
! , Mix 60, , , . ,
. ,
.
. ii ! , (90C), , , , .
ii ; Ii i
,
END OF CYCLE.
i START/PAUSE
.
! , Mix 30, , ,
i, .
31
i
UA
i :
:
.
i ( A).
, i. .
.
! .
, . :
A
i
B
i
4
MAX
ii i, : ,
- / i.
- : i i i i i. ,
. , .
i
i: ,
ii : . 7 , .
i : . 3
ii : . 2 .
: . 1,5
: . 1
? .
1 400-500
1 150-200
1 400-500
1 900-1200
1 150-250
32
!
. . UA
, ,
. .
,
i
. .
,
,
. ,
, -
, , :
. ,
. 1.
.
2. ,
,
.
20
;
.
,
,
,
,
,
.
.
i i
.
3.
: , ,
.
: (.
i i ).
i.
i ,
i ii
ii .
i, i
.
i i.
i
. i
i - i ,
.
, ,
.
:
, 4. i
. i,
2002/96/CE i; i i ,
i .
,
5. , ,
. , i
i .
, ,
33
UA
,
.
.
.
. , .
, (,
) ,
, .
, . ! , ,
. .
, :
-
. 1.
( 10%
)
(.
);
.
40 .
A B 5 . (. ).
70 .
i START/PAUSE. 2. ,
A B (. ):
ii
;
3. ;
4. ;
5. , ,
, i
1 i , i i .
i
(. ).
;
.
. ,
:
2
.
! , i i.
34
, . i (.
), , , , . UA
: /:
. i.
.
. .
ON/OFF .
START/PAUSE .
.
i (. ).
i .
.
( .
No water, check supply). .
.
START/PAUSE .
65 100
. (. ).
(. ).
i ii i.
,
, i
. ,
, ,
. ,
, .
:
i. (. ).
i
i START/PAUSE ( ).
(. ).
.
i i , ,
i. (. ).
(. ).
(. ).
. (. ).
( .
).
(. ).
, , 1
.
(.: F-01, F-..). , i .
. (
, , ).
.
35
195097594.00
11/2011 - Xerox Fabriano
i :
UA , (. );
, ;
i, i i , ,
i ii.
! .
:
;
(.);
(/).
ii i i i i,
i .
36